DesignJet 350 c

Similar Questions

• HP Designjet 350 c driver

  I'm looking for a driver for a HP Designjet 350 c printer. Problems with the Vista compatibility.

  Hi grainhandler,

  You can download the driver for Designjet 350 c here: http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=12642&lang=en&cc=us&taskId=135&prodTypeId=18972&prodSeriesId=28430

  I hope this helps.

• DesignJet 350 c E/A0

  My Chartplotter goes all the Service Mode, we test still fails when loading the roll paper. It goes through all the usual steps to advance the paper, etc. Then feeding roller reverse and spit the paper. The LEDs indicate then 1259 bit that I can't find that anywhere as error code in the maintenance manual.

  If there roll of paper in place and I press Form Feed the roll of media turns backward and keeps spinning until I get the book far enough to clear the media sensor.

  Clues?

  I'm not working on one of these years. One thing, you may want to check is stick something in the cover open button so you can see the action of the transport as it moves to measure paper. You should see a Flash of red light down first on the left side, then transportation should move to the right side with the red light on until it reaches the edge of the paper and then stops. What this. Sometimes the receiver part of the blockage led table with ink so he does not see the return of red light that it touches the edge and see the black tree that reflects the light from the back.

• I bring you my affected MacBook Pro (17-inch late 2011) at the centre for Apple in Algeria and they refused to cover the repair and asked to pay $ 350.

  I bring you my affected MacBook Pro (17-inch late 2011) at the centre for Apple in Algeria and they refused to cover the repair and asked to pay $ 350.

  When did you purchase the MacBook? What reason they gave for the tarp does not it? What you expect from us, your fellow users?

• When you use unified folders, the high-level junk folder indicates a number of 350, although there may be no spam in any of the accounts. How can I erase this number?

  I went through all the settings. I deleted and recreated the e-mail accounts. I have restarted Thunderbird. I rebooted the macbook. Disabled all plugins and Add-ons. Nothing gets rid of this false charge. This is what it looks like (sorta):
  Inbox
  Air currents
  Envoy
  Junk (350)

    account1 (1)
    account2
    account3
  

  etc...
  Any help or sympathy enjoyed.
  Linda

  You can try to rebuild the Junk folder: select Help/Troubleshooting Information, show the folder to open the profile folder in Explorer, TB of output, look for the files Junk and Junk.msf (mbox file) and index file, rename them or move them out of the profile folder, restart TB and see if a junk clean folder is created after you mark the first message as spam :

  http://KB.mozillazine.org/Compacting_folders#Real_fix

• I teach a cardio dance class on the inside and I can't give them a many exact calories when class ends.  The only choice is on the Apple Watch is the 'other' and I know that the class Burns 600 calories in an hour, but my watch shows only 250-350 burned. 

  I use my Apple Watch throughout the day and when I teach a cardio dance class, the number of calories is MUCH lower than other materials.  Why is the Watch not count my calories accurately?  The ladies like to know the calories to burn when the class is over and I can't give them using my Apple Watch.  Others in this class that wear the watch tells you how many is not too accurate.  We burn usually about 600 + calories and I'll be happy if my registers 350.  What could be wrong? Thank you!

  Hello

  Do not forget that Apple Watch uses Active calories (those who are burned by orders or travel) as the main measure for the app to training and activity app.

  Many other applications of fitness / devices report total calories, which consists of active calories + calories at rest (that your body is still burning even when you're not active).

  More information:

  Use the activity on your Apple Watch - Apple Support

• Designjet T120: HP T120 error BA7F11E0 designjet

  We have a HP designjet T120 when power on/off, this (BA7F11E0) error message appears on the screen immediately.  No movement of transport or initialization is performed. Just the error and nothing else. Pls help.

  Thank you

  Hello

  Try to isolate the printer, remove the printhead, inks, connectivity cables and turn on the printer.

  If the error persists, it may be a problem with the APC hand.

  Best regards

  Mike G

• DesignJet 130nr: canvas print Designjet 130NR

  Print on canvas of sheet (13 x 19) on Designjet 130NR works very well. Called HP Support asking if there are 24 "canvas rolls that work. Told me and it makes sense, the tool can not handle the Cup fabric.

  Someone at - he found and printed successfully pre-cut large canvases for the 130NR? I've got a good big letter opener, but as anyone who uses the 130 know, it rejects easily paper cut perfectly.

  Thank you

  Marty

  Hello

  Strawberry is not really designed to cut the canvas. Is too thick

  You can still use it, but you will need to replace it more often.

  If your knife used to work, you may need to replace it now

  Here is the part number Q1292-60064 Media knife

• Designjet t125: designjet t125 blue screen error B332347C

  Hello.

  I was ask to get this error:

  When you feed the plotter that blue screen appears with this code: B332347C

  I can't find the service manual for this, if anyone can help me?

  HELO try this solution
  You need to replace hp designjet encrypted t520 chip on the motherboard inside the plotter
  You can buy it on ebay http://www.ebay.co.uk/itm/HP-Designjet-T520-Blue-Screen-Error-Solution-Encrypted-chip/282223353841

• Designjet t520: designjet t520 error b3d73738

  HP Designjet T520 36 inches gives b3d73738 on the screen, never seen that before and isn't anythong on this subject,

  the printer does not start or let me take any operation

  need urgent hepl on this issue.

  Thank you

  Hello

  Try the following

  -Replace the power cable

  -Connect the printer to a different outlet

  -Isolate the printer, remove the ink cartridges, print head, cable connectivity

  If you still have problems, you may need to replace the APC's hand

• Designjet T520 36 inches (CQ893): Designjet T520 36 - in

  My tracer: HP designjet T520 36 inches (CQ893) start.

  The screen is blue, B87E7114 error code

  Turn off and turn on probably. Power button 15 seconds and powering button 50 seconds also.

  If push yellow power light. power on no beep error.

  End of warranty: 2015.02

  What is my error code?

  Thank you

  Sorry, but your post is very confusing.  You've got an ok error code, after that I do not understand what you mean by switch / stop and seconds.  First thing you need to do is to unplug the plotter of the power source.  Wait about 30 seconds and plug back in and if the power does not turn on by itself, use the power button to turn it on and tell us what appears on the screen.

• HP Designjet T1300 error 08:04

  Hello!

  I have a T1300 Designjet, a few years old (2010 I think) and I have printed a few rolls of paper on it. (5-6)? There are a few firmware updates he has begun to show 08:04 error message. He asked me to update the firmware, if the problem persists (does it well). I have the new firmware (?) IG_04_00_05.2.

  Sometimes I have to reboot 10 to 15 times before I can print. Sometimes it goes to error if I don't use pace for an hour or two. Sometimes he goes to error in the middle of printing, or just by turning or when ever. Sometimes it starts immediately and I can print all day with no problems.

  Any ideas?

  Now, I checked again for the new firmware. the printer says there is new firmware, but he went to 08:04 error mode in the audit.

  Now after 4 restarts, the printer started to install the new firmware. at the end of the installation program stops and when restarting, the printer starts at 08:04 mode.

  Restart the printer again and again. Allways 08:04 code. What is 08:04 code means?

  OK... updates history:

  Today first MS_01_01_23.1 was installed and after this IG_04_00_05.2.

  No newer firmware available.

  I will update this if it doesn´t enter the error mode more...

  Today, I finally had the time to print again. The T1300 always happening in error mode 08:04.

  Help!

  I've never seen an INVERTER causes a hardware failure, but I saw them will interrupt power.  I unplug it and try it this way for a test.   Can you connect a computer directly to the printer without going through your network and see if it starts and prints normally then?

• DesignJet T2530: T2530 selection automatic Roll Correct

  We recently bought a DesignJet T2530 to replace our old Gestetner requiring parts that are no longer available. We've had for about a month now and we had questions make him print the good roll all the time. We have a wide roll 36 '' loaded roll of 1 and a 30 "wide roll to roll 2. When printing the drawings AutoCAD or a PDF Adobe, 24 "x 36" designs would be to print in portrait mode (24"wide) to 30' wide roll instead of landscape (36" wide) to 36"wide roll." Also, 30 "x 42" designs would be automatic selection of portrait print (30' wide) for the 36"wide roll instead of 30" roll. " We called our service contract provider and they came out, looked through a bunch of settings and finish the download complete driver with PS drivers and HPGL2, set a custom. PC3 for AutoCAD file to force the printer to print 24 "x 36" designs on the 36' roll after we say from the printer, and everything has worked for a few days. " Service came out again, changed a few extra settings in the printer properties, ended up needing to replace the touch screen because it was just bad out of the box, and again once it worked fine for a few days. More recently this week, it started printing the 30 designs "x 42" 42"wide on the 36" "roll, cut 3" on each side of the drawing. " Service came out yesterday again, was here for about an hour, has insisted that it is absolutely not the machine and it must be a problem with AutoCAD and Adobe (which seems strange since it has the same problems of each program), tried a reset of the printer without result and basically said it's just not to the automatic selection the right to ride , so we will have to change the settings in the properties of each time that we print something. Then, after the left, custom. PC3 file, put it in place before (as previously mentioned) has stopped working properly and the 24 "x 36" drawings started printing out on the 30' wide roll again. " As it is now, when I print a drawing, I have to go into the properties of the printer in the print window, select the correct size paper, select the correct role and select the correct orientation so that it can print correctly. I put just customized. The PC3 in AutoCAD files for it so I do not always go through this when printing from AutoCAD, but I must still manually change all these settings for each picture I print from Adobe and I don't know if these custom. PC3 settings will decide to stop working again like last time.

  Someone else has had this problem on this model printer and, if so, have you found a solution so he can get the correct width for automatic selection?

  Hello

  Go to the printer Embedded Web Server and select the option use the exact width of the roll.

  Also, make sure that the drawing was generated landscape as the application will replace all the settings on the driver and the printer.

• HP designjet T790

  hp designjet t790 22.0.10 error code pls help...

  This code is important when someone replaces the star engine and when reinstalling the electronic module that they mix the large 2 connectors on the main map.

• DesignJet 200 C3180A: Lost printer driver-DesignJet 200

  I seem to have lost the driver for my DesignJet 200 C3180A antique during the upgrade of Windows 10. It worked two months ago (on Windows 7), and the only change I made to the computer - I think - is the upgrade. Now when I go on the list of printers it just isn't there. I tried to search the Internet but nothing seems available after Vista. I'm at a loss as to how I had it works on Win 7 now! Any ideas where a Windows 10 driver is not found?

  I connected via a parallel adapter / USB and the port was virtual USB001 (or was it 002?) and he has worked in the past connected like that.

  Any help would be appreciated, thanks.

  Hello

  Try this other driver for the DJ 430

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=11203514 & swLangOid = 8 & swEnvOid = 2100

  Hope to work