Designjet t120: ERROR B333007C

Amanecio con este error el designjet t120 B333007C PANTALLA AZUL Y No. HACE NADA No. SONIDOS NOMAS MESSAGES

Hola,

Papel, unit cables, el cabezal, initiates remover los cartuchos of tinta

Initiates otro poder cable y otra coneccion.

If the problem persists that whole el hand APC.

Whole para part would UN tecnico.

ACA comparto el enlace a los foros Español

http://h30467.www3.HP.com/T5/impresi%C3%B3n-Escaneo-fax-y-Copia/BD-p/Escaneo

Saludos

Tags: HP Printers

Similar Questions

  • DesignJet T120 error 42: 10 (transport cannot move)

    I recently prunched printer DesigntJet T120 Wireliss

    and while I was printing a project (Roll - like paper A2)

    He is arrested when printing with the message "carriage cannot move, check the jam... etc.".

    and this is the position of transport

    (he moved there that the error pops up)

    so I unloaded the roll and removed support back Pope & searched the papers, there was nothing

    then the 42: 10 error appeared when you turn on the printer

    and when I tried the diagnostic options, transport did not move with the same error (42:1:10)

    tried a soft/hard reset but it asks to enter a PIN number I do not know and can not find anywhere.

    can someone help me?

    Anyone know what is the PIN?

    Thanks in advance

    Hi Gendows,

    The Designjet is a commercial product.  I you a link towards the Designjet forums try to repost your question here for better coverage.

    Designjet Forums

  • Designjet T120: HP T120 error BA7F11E0 designjet

    We have a HP designjet T120 when power on/off, this (BA7F11E0) error message appears on the screen immediately.  No movement of transport or initialization is performed. Just the error and nothing else. Pls help.

    Thank you

    Hello

    Try to isolate the printer, remove the printhead, inks, connectivity cables and turn on the printer.

    If the error persists, it may be a problem with the APC hand.

    Best regards

    Mike G

  • Designjet T120 does not print full page

    I recently bought a designjet T120. I am printing drawings to her and it is printing only half of them. I had this problem on a designjet T520, and you get the error "out of memory". If you go in the printer preferences, then advanced, you can choose to send the work in the form of bitmap and it feeds through.

    My problem is that in the T120 printing preferences, there is no option to choose it. Under document options - features of the printer it doesn't have the ability to send in the form of bitmap.

    Any help? Thanks in advance

    What operating system the drivers are different for each operating system. If you still have the T520 driver loaded, change the port to the port of the T120, and see if it works like so many drivers use the same printer language.

  • Designjet T120: T120 - sustainability of the printhead Designjet

    Consider buying Designjet T120 for a small office, where my question:

    What is the sustainability of the print head? (how many pages can be printed)?

    With almost all designjet hp I've seen over the years, the print head life is never determined by the number of pages. There are just too many variables.  Unlike most printers Designjet the T120 T520 doesn't have a separate print heads, but is rather a unit and is replaced as such.  I have not heard or seen any problems with the printhead on this model, so I guess that it will last several years.  With printers Designjet most lack of use is the cause of most of the problems with the printheads.  Also do not have the cart placed above the service station causes problems.  Example the belt has a problem for the plotter stops in the middle and the user plan nor get the fixed tracer for over 2 weeks.  This has a detrimental effect on the printhead (s) as they tend to dry out when not capped.  The correct use and fairly constant use of designjet keep the printheads for years.  I have repaired several hp Designjet printers where the print heads are more than 10 years and still works fine.  However I maintained Designjet printers where the print heads spoil in less than a year with most of them in the latest, due to lack of use.  I also perfer for guests to leave their tracers on all the time.  Less stress on the components as they go through many electrical test when the first being enabled.

  • HP DesignJet T120 prints blank Pages with software of CAD DraftSight

    Hello

    I grew up this question with the DraftSight support as well.  They are currently studying the issue, but I doubt very much they can do about so I wanted to get feedback from the HP support as well.  Basically, the problem is that I can't print using the HP DesignJet T120 and CAD software free DraftSight.  The job is sent to the printer, but the pages come out blank.  I was hoping that if someone can also confirm this behavior or help me solve the problem.  Here is some information on my situation:

    1. I can print other software for the T120

    2. I can print draftsight on another printer (Toshiba e-Studio 281)

    3. my system configuration:

    -Windows 7 x 64

    -Printer connected via usb

    -Use the latest printer drivers for T120 (61.124.1518.100)

    -DraftSight V1R3.1 x 64 http://www.3ds.com/products/draftsight/download-draftsight/

    4. I tried the method of pilot alternative described in http://h30434.www3.hp.com/t5/Printer-All-in-One-Software-Drivers-e-g-Windows-8/How-to-Assign-Alterna...

    but it is not really one another driver I can choose.

    I appreciate all the help and feedback!

    Thank you!

    I'm linking you the Designjet forums below. Please just transfer your question on the forums of Designjet.

    Designjet forum

  • Driver missing for HP DesignJet T120

    Cannot install the printer driver for the HP DesignJet T120

    Well windows OS must have access to the software of the printer. To do this, run or cmd, type: appwiz.cpl

    In Add/Remove components of Windows Open (menu L.sub) highlight the printer, chk, the outlet boxes.

    This opens the services or...

  • print landscape A3 on Designjet T120

    We have a new plotter Designjet T120, which works very well!

    The problem is, I can't get a correctly printed A3 or A4 landscape. Apparently, it is not made that he must return the print job 90 ° to make things...

    Is there a setting I need to change? It seems really stupid, but I don't know why it isn't done automatically...

    I really want to get this setting right, to get the maximum from our printer.

    Thank you!

    solved!

    I had to install Microsoft Update Net4 MS., afterwards, I was able to install software from CD ePrint. After installing ePrint, I had a 'radio button' to aktivate the PREVIEW. Now I can print with preview and rotate the output as I like.

    Lars

  • How to install a DesignJet T120 (or other) driver printer bypassing the printer connected?

    Hi all

    As shown in the topic, how can you install a printer driver without going through the connected printer?

    We have a user who has problems with its layout with the DesignJet T120 and want to help reproduce the problem so that we can find a solution, but it seems that, without actually connecting the printer, the driver installation is less difficult.

    We use Windows 8, but have access to all the operating systems.

    Thanks for the solution!

    OK, you can find the answer here:

    http://h30434.www3.HP.com/T5/printer-all-in-one-software-drivers-e-g-Windows-8/CP1518-installing-drivers-without-printer-present-for-remote/TD-p/104904

  • HP Designjet T120: T120 Designjet error HP: 805D06E31

    Hello

    My HP Designjet 120 gives the error code: 805D6E31.

    I tried to install the new drivers, but my printer will not be available in the Hp Utility tool.

    Of course, tried to reset it but you need the touch screen for this. which displays the blue screen.

    Any solutions guys?

    Found the solution.  The plug was defective.  replaced and it worked.   @HP - please get this error on a Web page code, sound very confusing and it is illogical that this error code is not traceable at all.

  • HP Designjet T1300 error 08:04

    Hello!

    I have a T1300 Designjet, a few years old (2010 I think) and I have printed a few rolls of paper on it. (5-6)? There are a few firmware updates he has begun to show 08:04 error message. He asked me to update the firmware, if the problem persists (does it well). I have the new firmware (?) IG_04_00_05.2.

    Sometimes I have to reboot 10 to 15 times before I can print. Sometimes it goes to error if I don't use pace for an hour or two. Sometimes he goes to error in the middle of printing, or just by turning or when ever. Sometimes it starts immediately and I can print all day with no problems.

    Any ideas?

    Now, I checked again for the new firmware. the printer says there is new firmware, but he went to 08:04 error mode in the audit.

    Now after 4 restarts, the printer started to install the new firmware. at the end of the installation program stops and when restarting, the printer starts at 08:04 mode.

    Restart the printer again and again. Allways 08:04 code. What is 08:04 code means?

    OK... updates history:

    Today first MS_01_01_23.1 was installed and after this IG_04_00_05.2.

    No newer firmware available.

    I will update this if it doesn´t enter the error mode more...

    Today, I finally had the time to print again. The T1300 always happening in error mode 08:04.

    Help!

    I've never seen an INVERTER causes a hardware failure, but I saw them will interrupt power.  I unplug it and try it this way for a test.   Can you connect a computer directly to the printer without going through your network and see if it starts and prints normally then?

  • Designjet T120: Can't trace file size D (T120)-specific PDF drawing

    Hi all

    Having problems trying to draw a PDF specific drawing D-size (SolidWorks saves) on our plotter T120.  It plots just fine in the sizes A, B and C, but when I try D, it just hangs, then times out with an error.  I tried to update drivers, run the HP diagnostic utility, run the utility from Microsoft, etc. but nothing seems to work.  I traced several other designs in the past in D format without any problem (tried a while ago with a different design of PDF and it worked fine).  Looking for ideas...

    In which case it is important:

    * Wireless printing

    * The PDF file size is 1.30 MB (spools up quickly to 13.4MB/15.7MB then crashes)

    Thanks, Jeff

    Hi Jeff,

    Thanks for your reply. Maybe you are not understood my message. First update you the firmware from the link below: Driver and Firmware through EWS and follow the instructions.

    Latest Firmware: Version - AXP2CN1623AR; Date - August 1, 2016; Size of the file - 24.7 MB

    Please share your firmware version. who is now in your printer.

    The printer settings printer Goto and information on the internal use print printer page them you can find the firmware information, or also through printer EWS.

    Firmware can not uninstalled process.

    Thank you
    Rashed

    I'm not an employee of HP, but I am an engineer @ HP Partner and I share my knowledge of my own time.

    If your problem is resolved please click the button "accept as a Solution.

    If my answer was helpful, please click the 'Thumbs Up' to say 'thank you '.

  • DesignJet 5500: DesignJet 5500 error 5015

    I have a 5500 DesignJet.  I changed the ink, cartridges and the dye prinheads 81 to 83 UV tubes.

    I get error printhead code 5015 (only the black print head) which is a print head "internal power failure" or "Printhead Cleaner is not correct type" according to which manual checking.

    I didn't know that the printhead cleaners are different. How does the printer know vacuuming is of the wrong type, is there a chip in the vacuum?

    Anyone know where I can buy cleaners printhead for a reasonable price?

    Or, is it an internal electrical failure of print head? And, is it possible to disassemble the print head and set the internal electrical failure?

    The first hypothesis is correct.  The black print head has a power outage.  I would replace the print head first.  See attachment.

  • Designjet 800: designjet 800 error code 11:11

    Anyone know how to go about resolving the error code 11:11 on designjet 800?

    Hello

    Here's what means error

    System error: 11:11

    Problem

    Description:

    Rear cable not connected.

    Corrective actions: End plug correctly.

    You will be recolve reconnecting the cable or by replacing it.

    Best regards

    Mike G

  • Designjet T2300: Error 59.3 Designjet T2300

    Hello.

    I wonder to watch an error Designjet T2300 8.01.

    Someone in front of me like a tried to solve the problem by replacing format it and the hard disk, which are both recycle parts.

    For this reason, he created an error 59.3 & 8.04 (tracer require new original pieces of work).

    The control panel were also replaced.

    So after some tests it looks like no drive must be replaced.

    Do I have to replace the trainer so if I replace the hard drive?

    Thank you.

    I got the number of part of a confidential document from HP, you may have to contact HP service provider to buy the parts.

    You can also try the computers in Minnesota, they are fairly well informed and have many DesignJet parts in stock.

Maybe you are looking for

  • BT device detection not working no-Satellite A100 & LG mobile

    I connected my new LG mobile for my toshiba A100 running windows XP pro Service Pack 3. However when I try to send files from my pc to my phone and use the wireless transfer, the pc can't find my phone again through discovery - even if the PC tells m

  • 600 dead or not?

  • Create local variable programmatically in TestStand

    Can someone please explain the process of creating a local variable by programming?  I searched the forums but have not found what I'm looking for yet. I have an array of unknown size.  I use a foreach loop to go through the table and enter the data

  • HP EliteBook 8440p: BIOS of HP EliteBook 8440p administrator password

    Please indicate the BIOS HP EliteBook 8440p administrator password. If this isn't a solution, kindly suggests the following method to resolve the problem on my system. During commissioning, it says "non-system disk or disk error Replace and strike an

  • Active Sync problem - push slow

    Hello I use the premium new Z5 with Active Sync (Microsoft Exchange Online). The email push notifications come very late, sometimes several minutes later. What could be the problem? Thank you Marco