Designjet T520 36 inches (CQ893): Designjet T520 36 - in
My tracer: HP designjet T520 36 inches (CQ893) start.
The screen is blue, B87E7114 error code
Turn off and turn on probably. Power button 15 seconds and powering button 50 seconds also.
If push yellow power light. power on no beep error.
End of warranty: 2015.02
What is my error code?
Thank you
Sorry, but your post is very confusing. You've got an ok error code, after that I do not understand what you mean by switch / stop and seconds. First thing you need to do is to unplug the plotter of the power source. Wait about 30 seconds and plug back in and if the power does not turn on by itself, use the power button to turn it on and tell us what appears on the screen.
Tags: HP Printers
Similar Questions
-
Designjet t520: designjet t520 error b3d73738
HP Designjet T520 36 inches gives b3d73738 on the screen, never seen that before and isn't anythong on this subject,
the printer does not start or let me take any operation
need urgent hepl on this issue.
Thank you
Hello
Try the following
-Replace the power cable
-Connect the printer to a different outlet
-Isolate the printer, remove the ink cartridges, print head, cable connectivity
If you still have problems, you may need to replace the APC's hand
-
Designjet T520: Designjet T520 PCA main Board
Why the different part numbers for a 24 "and 36" Designjet T520 hand PCA Council?
Can I interchange the two parties?
24 "CQ890-67081
36 "CQ890-67097
Hello
Yes, they use the same hand APC
Do not use a main ACP USED, you will have other problems.
-
Designjet T520: Designjet T520: failure of the printer
Had Designjet T520 about 18 months. Use it only for printing large format on roll paper. Error message: the printer failed. "There is a problem with the printer or ink system. Turn the printer off, then on. If the problem persists, contact HP. »
Have made the procedure "on - off" several times including disconnect, allowing the printer to sit idle and then plug it in, turn on and still the same problem. I also removed and checked each ink cartridge and cannot detect all problems.
Remove all the ink cartridges and turn on the plotter. When he asks the ink, put them in one at a time and see if the error is displayed when only one of the ink cartridges installed.
-
HP Designjet T520 color prints have strips
The plot of a file prn in an Autodesk product: Revit using HP paper, the color of drawing a 1 4 "strips that lighten a dark color. The stripes running lengthwise through the drawing, in parallel with the wide edge of 36 "of a conspiracy of 24 x 36. If the size of the plot is changed, the bands remain 1 1 4 "wide. Spare bands natural color for 1 1/4 ", then a band that clears up the same color, then color. No banding occurs on the black and white prints
It's a problem of correspondence of GIS of paper Type. When a roll of HP Designjet Bright white 24lb paper is used, the type of paper bearing the same name is selected, then the file printed correctly, no strip of color - Revit and Bluebeam.
If the paper type does not match the paper roll in the HP T520, print quality has visible lines. On the touch screen of the printer, press 'Roll', touch "document Type", "More" touch, touch "Bond and covered with paper" or read the HP manual, page 107
-
Designjet t520 36inch spit long paper instead of print
Product is HP Designjet T520 36 "tracer. 36 "roll paper installed. Printing from Adobe Acrobat, maps of large size, print to 35 "x 60". Sending of print on the drawing board causes the plotter spit a large white paper instead of print. Do you receive an error message.
Help ~ it's wasting a whole roll of paper! There is no way to cancel or suspend the plotter when it feeds large blank sheets instead of print.
We tried different settings. Updated the firmware today. Very frustrated ~ can someone help please?
I solved my problem by determining there was something wrong with this particular PDF. As another PDF of the same size and similar content files have been feeling very well, I'm focused on PDF export process.
This 'problem' PDF was created in ArcGIS. To resolve this problem, I have re-exported a new PDF, using graphics tablets vector (deflation LZW) and rasterize all symbols; the new PDF print very well.
ALSO, for anyone who uses Pipelogix with ArcGIS, make sure that your toolbar does not work properly. If you get the toolbar alerts, remove the toolbar and start a new session, before exporting a PDF file. This may sometimes cause the problem I mentioned above.
-
The HP DesignJet T520 firmware update
Hello
I have a HP Designjet T520 and I'm trying to update the firmware on the printer.
The printer is currently connected to our print through our network server
The aim Guide do the following:
Using the integrated Web server, select Firmware update
Although, when I connect to the web server, I don't see the update of the Firmware.
Can someone tell me where is this info?
Thank you
René
Hi ReneMenard,
The Designjet is a commercial product. I you a link towards the Designjet forums try to repost your question here for better coverage.
-
Designjet T520 printing with ink cartridge empty
can a t520 print (black) even if a color cartridge is empty or the printer stops all functions until the replacement of the cartridge?
We intend to replace a hp not by a T520 tracer (go maybe later us to the 2500 series) and especially question is a "decision point" for "buy or not.
Thanks for any official information on the subject.
Best regards / WAG_Frutigen
This forum focuses on the level of consumer products. For the Designjet that you can have better results, post in the forum HP DesignJet here, this is where the DesignJet experts.
-
Printing on roll paper using hp designjet t520
Hello
I bought a t520 24 "hp designjet printer that can print on a 24" or 600mm roll.
The problem I have is that I can only select format A1 (594 mm x 840 mm) but I'm not able to select a custom size to really make use of the roller. Does anyone have experience with printing on rolls?
Thank you
Jakob
We have a different designjet, but I may be able to help. Our current designjet is not postscript, and Custom is grayed out in the main menu to print. Enter the Page Setup and choose manage custom paper sizes, we can define the size here. On our printer, the unprintable area must be the moins.25 on the et.67 on the bottom sides, or Setup fails.
I think that it's related to the absence of postscript because our previous design jet was equipped with postscript, and we were able to define page formats custom in the main window of the print.
-
DesignJet T520 36in: DesignJet T520 36in printing problem
I have a banner that I created in Adobe InDesign CS6. File is 12.2 MB. The file was created 36 "x 70". When I try to print in our T520 it will print only a small part of the left area of the bottom of the picture.
I tried printing from, PS, ID, Preview, Acrobat, ArcGIS... all with the same result. and using PDF, JPG, etc.
I also tried the 34 x 68 thus configuration.
It seems that if I select E papersize and tailored size, it begins to print across the width of the banner. I would not waste the ink to see if it does not print the entire banner.
So, best I can tell, something goes wrong, after that I will more than 44 inches in length on the banner.
Any thoughts on how to get the full banner to print? Thank you!
Really not an expert in this area but what happens if you reverse your size settings. Instead of 36 X 70 have it size 70 X 36 as the printer maybe is the thought that the 70 is the width it cannot the printer.
-
Designjet T520: Designjet T520 24 in. don't size printing
Hello
I try DJ T520 of my office to print a size D ANSI drawing. We bought this one a few months ago and it works fine, but I found an option that we had in our old office in isn't there anymore. I used to be able to rotate the print 90 degrees manually in the print settings. Because we have 24 in the version of the printer, I need to print the drawing in the portrait which means he needs to rotate 90 degrees, so it can adapt. Is there a way of setting this? Is this just a problem of drivers? I worked with our company this GUY to try to understand this. Thank you!
Please see the section "Use paper economically" to the following HP web link to use the desired job rotation option:
http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c03559791
I hope this helps!
-
Designjet T520 print size problem
Hello my name is Sonny, we're a small plane forming of sheet metal co. We print a lot of drawing and plate unfolded size. We use Catia, Solidworks and Surfcam most. We recently bought a T520 replace our old 750 c +.
The problem I have is the ratio is out of length, width, if I print a 24.00 24.00 x sq it prints x 24.00 23.95.
I tried it on vellum paper and 4mill inkbond and with the settings of all the 'best '.
been through the book and tried everything I think.
need help please.
Thank you
Sonny
Hello.
Not easy to understand, but I guess the print length is too short.
If you go into the setup, you should have the quality - calibration paper feed maintenance.
Run calibration in advance paper create and test with new impression.
-
Designjet t520: designjet t520 default login and password for web server
Hello!
Which is the default login and password for the web server and how to reset the password?
Hello
As mention Rashed, there is no password to the factory.
Try a Restore Factory Settings.
If this does not work, go to the Help Menu and do a Soft Reset. (Don't do the hard reset).
For access to the support menu press on and hold the power button for 15 seconds, or at the home screen tap home, back, home, home.
Concerning
Mike -
HP designjet t520: Hp designjet t520 of emergency firmware recovery
Hi, there is no solution to recover the firmware on the system board flash drive?
PC sees only "PSC sboot" device. y at - it pilot for pscboot and flashing for this utility?
can I copy some how internal firmware file to flash drive? everyone?
Maybe someone - internal flash disk image?
-
DesignJet T520 36 "tracer: DesignJet T520 36" takes hours to print my PDF graphics files
It wasn't a problem for a few weeks after I installed the drivers on 2 users PC. Then both started having this problem. The PDF file can be 20 MB for example and the print job in the queue is create a "spool" file that is 5 times bigger and 2 hours to print. All of my PDF files do so. A 20.4 MB PDF created a 537 MB file when sending to the printer. Only a night or more than 5 printed pages. Don't forget, he did not this time at first. We also tried printing directly on the plotter via a USB cable. No improvement. The driver has been installed a few weeks ago and downloaded from the HP website. And two HP computers, a laptop and the other an Z210 workstation, take the ridiculous time even to print.
Is there a setting on the printer or in the device settings on the PC that could be the problem?
Thanks in advance for your help.
Hello
That's right, according to the amount of data is on the file, when it reaches the spooler starts a larger file, the numbers you give does not sound weird.
That's what you can try:
1. at the computer, go to printing preferences > Advance > Max. Resolution enforcement > select 300
This wil help you reduce the amout of data sent
2 - If you print from Adobe Reader, go to file > print > Advance > select print as image
It will be flat image and can help with the issue
3. before saving the file in PDF, flattening the image in a single layer. And if possible, reduce the dpi.
I hope this helps.
Best regards
Mike G
Maybe you are looking for
-
How to edit the Windows Installer build system Path Environment Variable?
My library feature vi uses appeal to post a link to a dll, the dll calls several other dll. If I create an installation package and install and put all the conscripts of the dll in the Windows\System32 directory on a target program machine works ver
-
can I put my taskbar across two monitors?
I hooked to a monitor to go with my laptop and I want the taskbar to be available on both screens. I want to continue to use the dual monitors as separate screens (I put "extend these screens") can I do? Also if there is another cool thing I should k
-
Error code: 8024200d (cannot install updates)
Error code: 8024200d (cannot install updates)
-
ARE THERE WINDOWS 8 TO 8.1 UPGRADE FEES?
I received an email saying that I can get a free update of Windows 8 to 8.1 now I just see that if you download the upgrade through Windows there are a load of HP. It is a HP computer brand new so I thought that maybe it's a promotion at HP and I wan
-
Can't re install epson multifunction thatstoped work
After you run the majority of the installation installation displayed in error and cannot complete the process