Designjet z5200 will not print red

Similar Questions

• Photosmart C & 180 will not print red

  The printer has suffered when we had a power cut and he was turned on.

  Since then, it will not print red. (I just get yellow).

  Have looked through the wire "Will not print Magenta", I'm not sure who, magenta cartridges (or both), I need to try hard - or if there are a few other adjustments that I do.

  Hello Phil1812,

  Please confirm the process you have already finished.

  Another process, you could try is as follows:

  (1) remove all ink cartridges.

  (2) close the ink access door.

  (3) disconnect the printer.

  (4) wait for about 30 seconds.

  (5) connect the printer.

  (6) a message indicating to load the cartridges should appear on the control panel.

  (7) reload cartridges.

  Kind regards

  Lynn_B

• Will not print red

  Hi, I own a number of hp photosmart premium c310 series: model {deleted personal information}: cn503a it will not print red. Have preformed obvious troubleshooting, other technical suggestions. Could not do stack or facing other alternatives with similar problem

  Did you also check to make sure that the printer firmware is up-to-date?
  I would like to do a manual cleaning the contacts on the cartridges, the printer and the print head next to ensure that this accumulation on these pieces is not the cause of the problem. Solution 4 this document here shows how to clean the contacts of the cartridge on the cartridges and the printer. The solution in this document here shows how to clean the print head. I know that the titles of the documents do not meet your specific question, but they are the steps to take to remove accumulation. If you have the print head of the machine, take a look at the printed on date while you clean the contacts that the date is in this part of the printhead. If this date is not passed, this is a replaceable part that can be troubleshoot-performed and replaced by contacting HP Total Care. If this date has passed, please post back with this date and I can give directions over here.

• DesignJet T770: DesignJet T770 will not print in color

  After you move a DesignJet T770 44 inch queue from a Windows 2003 server to a Server Windows 2012 R2 the T770 will not print in color.

  The general tab on the properties T770 printer States ' color: No. '.  Yet once on the printer properties on the tab color color management is set to "Automatic (recommended)".

  The T770 printer driver has been downloaded from Windows Update I was unable to get a T770 driver from the HP website.

  The T770 product no is CH539A / CN375A. Strangely, none of these product numbers have been recognized by the search for product number for th HP Web site.

  My question is how do the T770 to print color again?

  Any help would be appreciated.

  I would say that you definitely have a driver problem if you has not changed the settings in the built-in web server printer at the time wherever you spent since Windows Server to the other server in Windows.
  
  I check all the settings on each tab in the driver to see if it is possible that somewhere in there color is disabled.
  
  I also go back to HP.com and look for driver for that machine again.
  
  I am also looking for a print utility for this machine, which should not be confused with a printer utility, even if they might be named roughly the same.
  
  I recall there are two utilities is to monitor the status of your printer, and the other is to print and work around the driver.
  
  When you have found the right print utility you save your print format JPEG or PDF file and then open it in the print utility and send it to the printer without ever open drivers.
  
  Another experiment, you can try it if you have a practical PDF just open a web browser and access the built-in web server printer and then try to print the PDF file directly by using the option for printing on the web server.
  
  The purpose of some of these things is number one determine if the printer has developed a problem that it prevents printing color and print JPEG or PDF from the built-in Web server where all you do is send the file directly to the printer would let you know that the printer is always able to color.
  
  So if you can get the print work utility where you can open the PDF on a PC and then send it to the printer you have to least a workaround while you solve the driver problem.
  
  If my post solves your problem, please click on the accepted solution button under the post. Thank a technician for their efforts in the creation of these posts please to give them a little nudge upwards, just click this icon under the post and give them a few congratulations.

• HP ColorJet 2600n: HP ColorJet 2600n will not print RED

  I have all new 4 124 HP toners and HP124A (combo) installed at the same time, but the red color does not print. I had the same problem with the last 4 tones and thought the Magenta was BAD, and now with all new shades, the problem is still there. Help, please!

  The goal of the scanner is sprinkled on.  Here is a sheet of instructions with pictures on how to repair.  It will take some time but works perfectly when you are finished.

• 895cse will not print red or yellow

  Arrested 895Cse print any color (white). I put in new cartridge. Now, it will print blue but not red or yellow (again just empty). Black is fine.

  OK, a few things to check - I would start with the date on the cartridge as described in this document.  A few years ago, I ran across a major retailer who had long expired cartridges for sale, they probably would have questions right out of the box.

  Although it is possible, this could be caused by a printer hardware problem that is less likely, that all colors are driven by a single chip driver.  It woud not likely that two of the colors fail but cyan would still print as a result of the failure of the electronics.

  A way to check the cartridge would be as follows: remove the cartridge and gently pat dry the nozzles on a wet tissue.  A good cartridge would have strong cyan, magenta and yellow stripes.  If your cartridge only displays a task strong cyan, with a bit of magenta and yellow, then maybe it's the problem.

  If the task of cartridge shows not all colors there are a possible (but maybe temporary) solution.  Put a little folded paper towel in the bottom of a cup and drop of the cartridge on paper.  (That would be the same orientation that would be the cartridge in the printer).  Pour in hot water to a depth of about 1, 5-2 "and let the cartridge to soak for about ten minutes.  After soaking, remove the cartridge and gently dry the electric contacts with a fluffy - a coffee filter works well.  Replace the cartridge in the printer and try to print the page of diagnosis as described in this document.

• Will not print red F4580

  My f4580 prints everything red yellow, if I use the cleaning cartridge program it works but I have to do each time. Any help please

  The number of our UK customers should be: 0844 369 0369

• C410 Photosmart will not print red after magenta cartridge replaced

  Hello

  I just replaced the cartridge Magenta on my Photosmart C410, it was a genuine HP cartridge and the printer shows ink levels are now full but when I try and print anything in color that it is, or printing of the Red hues.  Any suggestions as to what I can do?

  Thank you

  Hello

  Please click here here for access which should solve the problem.

• Designjet 130: Two printers Designjet 130 do not print with Windows 10

  I have two printers Designjet 130. Both work fine with XP/Vista/Windows 7. They do not work with 10.

  I spent 20 hours trying to get these things to work with no luck. I tried TWO different machines running windows 10 does not. These printers are running via a USB connection.

  I can install, make the printer by default and PRINT TEST page! I can also print from the HP Scan DR who assures me that all is well. However, when I go to a program such as Notepad, they will not print. Notepad returns an error "The deal invalid. I tried researching this message, but it leads to good spirits more that I can understand.

  My machine is a processor Intel X 5960, 32 GB of memory and a motherboard Asus x 99 Deluxe.

  I tried to launch the installation of the HP software in a variety of modes compatible with no luck.

  I'm out of ideas other than to roll back my 7 software, which I really don't want to do.

  Thanks in advance.

  Ok. I finally solved this problem. I went to the HP site and even ONCE downloaded the driver Designjet 130.

  Download driver on Dec30, 13:34 had a 2 652 k file size

  Today at 11:53 driver has a file size of 3099 KB.

  Maybe they (HP) fixed.

  Maybe my original upload has been altered.

  Very simply:

  Connect your printer. Windows will find and automatically install the USB printing as well as a device driver option. This driver won't work, however, you end up being able to print a test page. This ultimately will always be a false confirmation. The driver version 7.00 is for Vista, Windows 7 and 8. It doesn't work in either compatibility mode.

  Go ahead:

  Go to devices and printers.

  A series of beautiful graphic icons opens.

  Double-click your printer.

  Double click on "customize your printer.

  Go to the about tab.

  Check your installed printer driver version

  10 Windows will install default v7.00 and will keep you in saying he has the best version

  available. Don't believe that.

  The Hewlett Packard scanner DR software will tell you the same thing.

  Do not think that either.

  You want to version 8.10. It is available on the site of HP in 32-bit and 64-bit versions. Download it. I unzipped in a folder on my desktop.

  Now, go to the Device Manager.

  Scroll down to "printers". Click on.

  Right click on your printer.

  Click on "Update driver software"

  Do not click on the first option by default.

  Do not click on "Browse my computer for driver software".

  Click on "Search for driver at this location software '-specify the folder on your desktop and select"include subfolders. "

  Click Browse. The software will make a satisfying update.

  Return to the file "Devices and printers" and the option "customize your printer.

  Double-click. Return to the 'About' tab and confirm that driver version 8.10 is installed.

  Close to everything and to print something.

  Just to check myself, I printed my second document to confirm a nagging doubt.

  The impression is confirmed. Good year for me and anyone else reading this.

• Epson printer does not print red color.

  Original title: I have a printer Epson SX110 Series. Troubel is that it will not print the coloar RED at all. All new cartridges, was working fine last night. Could you please help me.  Your JB

  I have an Epson SX110 Series printer. Troubel is that it will not print the coloar RED at all. All new cartridges, was working fine last night. Could you please help me.  Your JB

  Hello

  ·         You did changes to the computer before the show?

  ·         What application are you using to print?

  ·         What operating system is installed on your computer?

  Method 1: I suggest you follow the steps in the link to fix the problem:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 2: You can also try to download the latest driver on the Epson site and check if it helps:

  http://eSupport.Epson-Europe.com/CountrySelector.aspx?LNG=en-GB&data=emW65r3CP2FEFCEcZMfKegKdCohCVtGx

  Reference: & Support drivers: Epson Stylus SX110-known issue

  http://www.Epson.EU/nbsp/printers-and-all-in-ones/Epson-Stylus-SX110/drivers-support?target=article&Extn=.html&articleid=1334

  If the above mentioned methods does not help then contact Epson for assistance:

  http://www.Epson.com/cgi-bin/store/AboutContactUs.jsp

• New Photosmart 5520 will not print in black

  I have a new HP Photosmart 5520 printer all-in-one.  Black ink ran out so I replaced it with a previously used ink cartridge which is of the same type # 564 but a XL version.  This cartridge has been barely used.  Now, I just can't get anything to print in black.  It will print in color, but not black.  I tried to turn off the printer.  I put the cartridge in my printer and it worked fine.  What should I do?

  edgarlogcabin wrote:
  

  my printer hp 5520 will not print black

  The in the here document troubleshooting steps may help resolve problems with black not not printing on your Photosmart 5520.  Especially make sure to check the events as on the Six Solution.

• My HP Officejet 4500 printer all-in-one will not print web pages

  My new printer will not print anything when I try to print selections as a route on a web page of travel.
  Other features of the printer works k o such as print emails.
  I have Windows 7 Professional 64 bit system.

  "My new printer. »

  For a newly installed printer, you may need to reset some hidden preferences, print.print_printer, in particular, for Firefox to recognize the new printer.

  • See-> http://kb.mozillazine.org/Problems_printing_web_pages (see "Reset printer")
  • See-> http://kb.mozillazine.org/About:config

  If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.

  Not related to your question, but...

  You may need to update some plug-ins. Check your plug-ins and update if necessary:

  • Plugin check-> http://www.mozilla.org/en-US/plugincheck/
  • Adobe Shockwave for Director Netscape plug-in: install (or update) the Shockwave with Firefox plugin
  • Adobe PDF plug-in for Firefox and Netscape: Installation/update Adobe Reader in Firefox
  • Shockwave Flash (Adobe Flash or Flash): updated Flash in Firefox
  • Next generation Java plug-in for the Mozilla browser: install or update Java in Firefox

• HP4480: will not print in black

  I have recently upgraded to the version of windows in 10 home edition 1511.  I have a HP4480 that is compatible with windows 10.  It is updated with the correct drivers.

  My printer will be printed in black and white if I copy a document on the printer, HOWEVER it will not print in black and white if I print a document on my laptop or from a Web page.  I'm also using Microsoft Edge.

  I run Scan Doctor, clean my print heads, made sure everything is aligned, but can not determine why I can not print in black and white the computer laptop but can from the printer.

  The diagnostic message only I received is "peripheral composite USB does not work with USB 3.0' I have no idea what this means and don't think that I have the choice for the ports on my Inspiron 15R laptop 5520.»

  I've also posted on the Microsoft forums but really need to get the printer works with the operating system and cannot afford to buy a new printer just because I upgraded.

  Any help is appreciated.

  Thank you.

  Janet

  I solved the problem.  For some reason, my real print HP 60 cartridge was the question.   Almost empty, I left forward without problem.  Once I replaced the cartridge, all now print correctly in black and white.

• Office Jet Pro 8500 black ink cartridge will not print

  black ink does not print and alignment fails.  I cleaned the printheads through all the levels.  The colors print perfectly but black will not print.  I have reset the printer, run test pages, but still no black ink and unity trys to align, but fails.  The unit is no longer in warranty.

  Hi mariajw,

  Thank you for your answer!

  What I would recommend to do at the moment is to please call our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. Language-country selector.

  Best regards!

• My office print 8600 ProPlus will not print pdf files sent from an iPad with ePrint.

  My office print 8600 ProPlus will not print pdf files sent from an iPad with ePrint.  I just get an error message when I go to the HP Eprint centre.  It prints the address email of the coverage, but nothing else.  The attachment is not sure that I can see.  I tried to send an attachment from my Mac and worked well.

  Thank you for your response and I am sorry for the delay to return to you.  I tried save the Pages document in a Word document and send it to the printer using ePrint but it is even.  That is to say the handout printed but not the attachment.  However, when we removed the accompanying document and sent the attachment in its own it has worked well for we have managed to solve the problem. Thank you very much.