Develop a virtual drive on a Dell Perc 6 / i Raid 6?

Similar Questions

• "Setup cannot find not all hard disks" on Dell PERC 6/1 RAID controller-supported?

  Hi team - I have a Dell R710 (physical host) PE server that uses the Dell PERC RAID controller 6/1.  Windows Server 2008 x 64 is the host operating system.  VMW Server 2.02 installs and works very well, and I need to install W2K8 x 32 (guest) server configuration, but windows can't see the virtual disk with the same error "Setup cannot find not all hard disks", you get the installation on Windows XP Home edition- but the documentation does not say it's controller RAID is not taken in charge should be... any ideas?

  This is not a problem of the underlying RAID/hardware controller.

  Virtual MACHINE on VMware Server just to see the virtual hardware that you have configured when creating the virtual machine, or through the settings.

  Be sure to select the correct target OS when you create a virtual machine. This configures the disk controller HARD virtual appropriate, which should be supported on the OS installation media.

  If you have selected the right OS and still have problems, please post the vmx file.

  André

• Windows 7 x 64 driver for Dell PERC 320/DC

  Dear Dell,

  I'm migration of Windows XP 32 bit to Windows 7 64 bit and I'm looking for drivers for my Dell PERC 320/DC (RAID SCSI PCI - X controller).

  There is no compatible driver on this site, I've tried them all, even the driver XP 64-bit.

  Because I know the controller is based on Adaptecs ASR-2200, I went looking on their website for the drivers, but they were not compatible either. I tried them.

  Adaptec said there is a driver for the embedded ASR-2200 on the DVD - Windows 7/Installation, it's true, but also that, if selected manually is not compatible: when you try to install the driver, it returns "the device cannot start. (Code 10) ».

  I tried updates firmware, such as provided by Adaptec for the ASR-2200, but nothing helps: the type of controller does not match. No firmware updates have been executed. The card still has the original and functional v4.0.0 build 5813 firmware on it.

  The controller has always worked and it still works perfectly when using, for example, windows XP 32-bit, so it is not defective.

  The chipset of computers is also not cause some sort of hardware conflict, then it works very well in both my Precision 690 and T5400 under windows xp 32-bit, BUT NOT in windows 7 64 bit.

  I even contacted Adaptec on this issue, but they told me to contact Dell after trying what I already have.

  I already checked this support site and found these interesting links, but none were of no help:

  http://en.community.Dell.com/support-forums/servers/f/1466/p/17771774/17894760.aspx#17894760

  http://support.Dell.com/support/eDOCS/storage/RAID/P41698/320UG/en/index.htm

  So I hope that now a compatible driver indication can be given so that I can proceed with my Dell products.

  Please, help me on this one, it's my last hope.

  Thanks in advance!

  Kind regards

  aprocita (from Belgium)

  I used one I found of ASUSTek.

  Description Adaptec HostRAID Driver for Windows 64 bit V2.0.0.201

  506.08 file size (KB)

  http://support.ASUS.com/download/download.aspx?model=RS160-E3/PS4&OS=23&SLanguage=en-us

  Enjoy! :-D

• Reference Dell perc h800

  Hello everyone we recently bought dell precision t7600 and perc h800 map for

  control of Keystone md 1200 powe... Win server 2008 r2 is installed but no driver work for dell perc h800 tried so site Web of frim dell drivers but still no hope... am wondring if anyone can help me... Thank you

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/PowerEdge-T710?driverId=W7X7H&osCode=WS8R2&FILEID=3176115748&LanguageCode=en&CategoryID=SF

  Since you're under 2008 R2, you might be able to run the Package version of update for Microsoft Windows, but since 2008 R2 is not supported on the T7600, it may not work properly, then you can try the hard drive version.  Since the H800 is not supported on the T7600 at all, it is possible that none of the Dell drivers will work.

• Reference Dell 2950 Perc 6/i Raid card device driver

  Good morning community, I'm trying to find the Dell 2950 Perc 6/i Raid adapter Device Driver for Windows 2008 R2 Standard OS. Thanks in advance for your help. Modem489

  You don't need to load a driver for the PERC 6 / i in Server 2008 or newer version, the driver is 'native' for Windows.  If you think that you need a driver, I suspect it is because you tried to install and it is not all discs.  If Yes, do not forget that PERC does NOT support RAID/JBOD, then you must configure disks to a virtual disk (VD, matrix RAID) before they can be presented to the OS.  It can be configured in the CTRL-R utility (be sure to check the boxes of progress/Initialize options too).

• Dell OpenManage Essentials 1.1.0 and physical/virtual drive information

  We have OME installed on a server, and we followed the servers with it. I just added the customers, who are mostly Dell Precision T3500s, and I installed OMCI on clients. Customers found out and I get health and inventory data, but I get no information about physical disks is or virtual drives on the clients or servers. Am I missing a setting somewhere, or if it is not supported by this version, and I'll have to upgrade to the latest version?

  Doug

  Hey Doug, thanks for the question.

  I remember that we have added a few additional customer stocks associated with disc in the version 1.3 of OME.

  Thank you very much

  Rob

  www.delltechcenter.com/OME

• Reference Dell PERC H710P: Firmware hangs on Windows RTM 8.1 with the default driver

  My H710P Dell (with the last FW A04) PERC was working completely fine with the driver 5.2.220.64 on Windows 8, until recently, I tried installing Windows RTM 8.1 on the machine, it caused hang FW at the launch of the Windows installation:

  266	[Information, 0]	05 seconds restart	Controller ID: 0 edge revision: A01	1367
  261	[Information, 0]	05 seconds restart	Controller ID: 0 Package version 21.2.0 - 0007	1366
  141	[Information, 0]	05 seconds restart	Controller ID: 0 battery present	1365
  1	[Information, 0]	04 seconds restart	Controller ID: 0 Image version: 3.130.05 - 2086	1364
  0	[Information, 0]	04 seconds restart	Controller ID: 0 has started the initialization of the Firmware: (PCI ID 0x5b / 0x1000 / 0x1f31 / 0 x 1028)	1363
  15	[Fatal, 3]	2013-09-11 21:00:27	Controller ID: 0 Fatal firmware error of: line 1232 in... /... /RAID/1078dma.c	1362
  15	[Fatal, 3]	2013-09-11 21:00:27	Controller ID: 0 Fatal firmware error of: line 1232 in... /... /RAID/1078dma.c	1361
  15	[Fatal, 3]	2013-09-11 21:00:27	Controller ID: 0 Fatal firmware error of: driver has detected possible FW, FW to stop blocking.	1360
  389	[Information, 0]	2013-09-11, 20:57:11	Controller ID: 0 host driver is loaded and operational	1359
  44	[Information, 0]	2013-09-11 20:56:33	Controller ID: 0 time established for power: time 2013-09-11 20:56:33 34 seconds	1358

  Windows 8.1 was delivered with the version of the downloadable 6.801.5.0 driver from Dell, I also tried and committed in my opinion the FW even hanging the question.

  I'm afraid - anyone know what is happening?

  See you soon

  Chris

  Appearantly this is related to the latest driver from Dell. I've found a workaround, but it's a bit complicated:

  1 connect a USB stick which is big enough

  2. install Wndows 8.1 on the * USB drive *.

  3. start Windows, and then remove the current driver and install the previous driver for Windows Server 2012.

  4. use the 3rd party software (say that Ghost) to copy the windows from USB drive to VD on Dell PERC H710P controller.

  5. start Windows in the USB drive again and use 'bcdedit' to clean boot stuff

  in any case, I'm LSI 9361-8i, so it won't be a problem for me in the future...

• PERC H330 and Raid 5, try adding another SATA drive raid 5 array

  Hi all

  I have one server PowerEdge T330 with 8 slots of disc and have currently 3 SATA drives running a raid 5 configuration.  I have a virtual disk configured for Raid (must).

  The operating system recognizes the disk and is able to use the resources...

  My desire is to add another hard drive to the table (hard disks of the same size, same brand, etc.) with 4 disks without losing any data.

  I looked in the settings of the iDrac and the only adjustment was to add the new disk as a global hot spare or a hot spare dedicated to the virtual drive.

  I also looked in the BIOS and do not see a way to add the new drive.

  Does anyone know how to increase capacity?  I can blow the virtual drive if necessary and start over without problem.  I intend to gradually accomplish this Act until adding 8 disks. (5 times).

  Help!

  Hello.

  Management controllers RAID and tables is not made in the BIOS iDRAC or systems. For the management of the RAID (virtual disks) arrays, you have OpenManage Server Administrator (OMSA). If not installed, see the link: http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=TK61C once installed, go to-> Storage->-> H330 PERC controllers-> virtual disk--> sub tasks available-> select reconfigure and run-> then check a box to add the fourth disk on the next page. Follow the prompts and allows you to extend your range of RAID 5.

• Dell Power Edge R410 & Dell Perc H700 modular F2WGY

  Hi guys

  Need some advice please, a few weeks ago, we bought a Dell R410. This came with a modular 6/ir Perc. However, when we arrived at the installation of drives we noticed that the controller did not recognize disks larger than 2 TB. It's not good because we need to use 2 x 3 and 2 x 500 GB disks in a RAID 1 Configuration.

  After Googling autour, I came to the conclusion that the card that it came with the "Perc 6/ir' does not support disks larger than 2 TB.

  So, I advanced and bought a new modular a "Dell Perc H700 F2WGY" controller which apparently supports disks more great.

  the controller came yesterday so I removed the old Perc 6/ir controller from the slot in the bottom of the map editing and trendy "Dell Perc H700 F2WGY" modular at the same place. : Photo of slot, I inserted H700

  H700 card: see picture

  PERC 6/ir map: see picture

  Anyway, once I inserted the card and started, I was presented with the error; "PCIE training error" system HALT.

  Obviously this would not start any further. So I brought the wrong card? im confused at the moment between modular and integrated? the pcie slot is low for integrated only cards?

  I then add the new map on the PCIE Top slot. the system then started and he could see the card. However, it found no readers?

  What exactly I do bad will this card work at all? or I'm out of luck and need another card?

  Cappilio,

  The problem you are experiencing is due to the model of the H700. Map H700 modular version is actually designed for the blade server Poweredge series. The model that you would need is the H700i which is the version that is integrated, designed to go into the white storage controller slot you are talking about. The references are KK67X and CNXVV. The latest model of the H700 is the H700A which is the adapter, it's the model that is necessary for installation in a PCIe location.

  This link explains in detail in the overview H700 - http://www.dell.com/downloads/global/products/pvaul/en/perc-technical-guidebook.pdf

  Let me know if it helps.

• MD 1220 / PERC H800 - how Raid 1 virtual disks?

  Hello I'm trying to configure Raid 12 1 (two pairs disks) in my Inbox MD 1220 with PERC H800. I started with 12 discs as 12 virtual drives Raid 0 and have recently added 12 additional physical disks for a mirror. I am able to mirror 9 virtual disks but when I select my 9th virtual to the mirror, no drives appear as available. The other 3 drives are there in the 'ready' State, but manage to open or the BIOS configuration utility seem to be able to use them as candidates of mirror. My computer is running in a kind of limitation of Raid 1 with Cabinet / card? Operating system: Windows 2008 R2 Datacenter Open Manage 7.4 Latest firmware / drivers for PERC H800 thanks! Dan ouedraogo

  Hi Joey

  I just tried OMCleanup and reinstalled 7.4.  He exhibited the same symptoms showing is not the physical drives in the H800.  I can't find a download 7.2 but would be willing to try the previous versions.  A previous version of OM worked with the same controllers / speakers / computer, but I do not remember the version where I improved.  (I am an individual shop and am not very informed when it comes to managing open, its versions and how to install/uninstall).

  I can still kill the DSM SA connection Service by running a foolish occupation for the H800 report.  The report H700 works fine.

  Dan

• PowerEdge T110II - Dell Perc H200

  Hi all

  Is there a chance to use at the same time SAS and SATA HDD on the Dell Perc H200 controller installed in the PowerEdge T110II? Currently I 3xSATA HARD drive and I thought to add additional SAS HDD, so is it possible that controller to be taken in charge this kind of configuration.

  Thanks in advance.

  Martino

  Should work.

• Reference Dell PERC 6 / i stand?

  I have a Setup Raid 6 on a Dell PERC 6 / i on a Supermicro H8DGU

  running a trial of the esxi 5.5u2

  No matter what I try, I can't do the Dell raid card is displayed in the storage adapters. I don't get any device also appear for passthrough if it means something.

  I have the AMD - V active and I had once made quick initialization (it's now the initialization in the background) I saw him appear on the list as a possible drive to install esxi. That tells me the esxi sees the card and the raid. But once I'm in vsphere nothing appears. Have not found a lot of messages from people not able to pick up this card so I think that the problem is just me. Ideas of things to check?

  But I guess that even with 'Boot Support' is enabled on Perc, is yet to appear in ESXi?

  I just checked your listing of motherboards to Supermicro. It employs riser card for the PCIe slots. Just to rule out it because there are a lot of wiring on the Perc: the card is well adjusted to the port of mounting?

  You can check if ESXi usually sees the device by runiing "lspci - vvv" on the CLI/ssh. It lists the devices seen by the kernel, if Perc is not here I would consider the Perc is defective or some strange PCIe connection problem.

  I have a Perc 6 / I works well for a client on a DELL Poweredge 2950 ex personalised Dell VMWare 5.5 Update 2 but on SAS, disks. But it's all DELL hardware and software side. I assume that the custom DELL VMWare image works only on DELL systems.

  I have found several traces as the Perc 6 / I could run a little crazy if you use disks not certified by DELL. Also the Perc 6 controllers do not seem to be supported more than 2 TB of drives (see for example: disk HARD Support for 2.5 to 3 TB drives and beyond - TechCenter Extras - Wiki - TechCenter Extras - Dell Community)

  So, you can probably run the test to disconnect all readers of your first and remove the Perc firmware RAID configuration and see if ESXi detects and it lists. If it does not help either I ran the test on different materials/mobo.

• How to remove some virtual drives of portable Satellite

  MY TOSHIBA HAS A LOT OF VIRTUAL DRIVES, THAT IT LEAVES ONLY 1 FREE SPACE TO PLUG A USB BACKUP DEVICE.

  I CAN'T SEEM TO RECORD INFORMATION TO ONE OF THESE READERS, NO MATTER WHAT I TRY!

  HOW CAN I GET RID OF ALL OR PART OF THESE READERS VIRTUAL SO-CALLED OR GET A JOB?

  Hello

  Could you please put more details?
  What is your laptop model and what operating system are you using?

  It would be useful for other suggestions

• Message "Please disable software virtual drive and emulation.

  I just installed Indiana Jones Lego, but when I try to start, I get the message "Please deactivate virtual drive and a software emulation." I turned off of Daemon tools, but there is no change in the message. I use XP if that makes a difference. Any help would be appreciated.

  See you soon

  -------------

• Problem with the virtual drive.

  On my g6 Pavilion, I get the full message e: HP_TOOLS road.   It is a virtual drive on my pc, how do I deploy using DISKPART to BACK?

  Thank you

  Tom

  Did you make the registry change that I sent you a private message?

  So, I agree with your statement. These are certainly back up files. The question is; What is backup files?

  Microsoft System Restore only deals with backup of critical system files and registration and records in a hidden folder that is not easily editable. In addition, you verified that this is not enabled for this player. So who is excluded.

  Another possibility is that other Windows, such as Windows Backup service, creates these files. Backup Windows treats the user's choice of the files instead of just the files of backup system.

  Try the following steps.

  1. Click Start, type "backup and restore" and press ENTER.
  2. This will bring up the Windows backup window. It seems to be set up, or it asks you to configure for the first time?
  3. If it is flagged by the look on the left side and you should see an option "disable automatic schedule;" turn this option off. The backup will be not automatically, but you can always do it manually on this screen.
  4. Delete the file Moberdan_HP from the HP_Tools partition.
  5. Improperly editing the registry if you used it.
  6. Reboot the laptop and make sure that the problem is resolved.