Developer SQL does not recognize my network drive

Similar Questions

• Windows 7 backup function does not recognize the external drive connected to the wireless router

  I installed a Belkin router for my laptop and pc, it came with a usb port so that I can connect my external hard drive directly and share it as a backup drive.  But when I tried to set up in Windows 7, the backup options list.  The network recognizes it, but Windows will not let me select it as backup destination.  A buddy of mine said that the backup of Windows 7 does not work with network drives, but no matter who else thought of it?  Thnx.

  It depends on the flavor of Windows 7. The Home Premium version will not network disks, backup but the Ultimate version. You can connect your drive as a USB drive when you make your backup.
  _________________________
  ID #0316. If this answer was helpful, you can vote by clicking on the green triangle. If it solves the problem, click 'propose as answer. Thank you.

• Tecra S3: Installation of Vista does not recognize the HARD drive

  I try to install Vista Ultimate on my Tecra S3, but installation does not recognize the HARD drive.

  I tried to find the driver for Vista for my computer, but not found RAID.
  Tried it with XP drivers, but no longer works.

  Do you have an idea where I can download Vista drivers for RAID?

  THX

  Hello

  Your suggestion is good. The Tecra S3 supports the RAID, and the RAID driver is required to install the OS on the HARD drive.
  On the European driver Toshiba page I found a RAID for XP driver.

  I put t know if this driver will run under Vista, but I recommend to test.
  The RAID XP 1.3.8.0 driver version can be downloaded from this site:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU

  Please note; You can store the RAID driver on an external USB and Vista should recognize it!

  Good luck

• Satellite A30 - 30F does not recognize my hard drive

  Hello
  I have a laptop Satellite A30 and when I start it up I get this message:

  For Realtek RTL8139 (X) /8130/ 810 X PCI Fast Ethernet Controller v2.13 (020326)
  PXE - E61: Media test failure, check cable of
  PXE - M0F: Exit PXE ROM

  I think my laptop is trying to boot from LAN because that does not recognize the hard drive, but the drive is ok, I tried on another computer with problem. Sometimes, not always, and I don't know why, I can start from the CD. If I boot from the Windows XP installation disk, I can access the hard drive. I've run fixboot and fixmbr hard disk, but that does not change. The bios recognizes the hard drive. BIOS vertsion is 1.20. I tried to upgrade the BIOS, but I need to Windows, so...

  Thank you very much and sorry for my English :)

  Luis

  Hello!

  To message PXE, you can consult this document:
  http://APS2.toshiba-tro.de/KB0/TSB8A02G90000R01.htm

  I think that your HARD drive or disc HARD controller of the motherboard is faulty, but I don't know m.
  Have you checked the HARD drive with a special tool for this? The Drive Fitness Test can check the HARD drive for bad sectors or something else:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT

  Take the test and post your result!

  Good bye

• Satellite A205-S4777 - XP does not recognize the HARD drive

  Hello!

  Recently I buyed a new satellite Toshiba A205-S4777 with Windows Vista home premium installed
  and I noticed too many errors in Windows Vista and the pc is very slow so I decided to downgrade to XP

  I want to directly install Windows XP but the installer does not recognize the hard drive or more exactly controllers!

  I nLite Sata drivers in Windows Xp Sp2, I bought on the microsoft.com site!

  Everything worked well.
  The Installer recognized fine hard and Setup finallased!

  But here's the problem when loading windows and try to pass on gorge yourself sort of blue screen one unreadable!

  And restarts and let, it does all day the same thing!

  I'm afraid that I have not nLite the right drivers.

  Is there anyone Heve downgraded this model?
  Thanx

  Hello

  Maybe you did not use good SATA driver?  :| Who knows
  The point is that there are two different versions of Intel Matrix Storage Manager supports different chipsets.
  I put t know what chipset is in charge of your laptop but you should check this and must also check the description of the Intel Storage Manager and check what chipsets are supported.

  In addition, you should have a look here in this doc from Toshiba:
  [How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

  Good bye

• Qosmio F30 - 112 - Windows XP does not recognize the HARD drive

  Hello.

  I have a Qosmio F30-112.
  I tried to install the Windows XP Professional instead of the Media Center edition.
  However, during the execution of the installer, my laptop does not recognize the hard drive. Therefore, the installation cannot continue.

  I thought it might be a problem of corruption with my laptop and reinstalled Media Center Edition successfully.
  But when I try to install XP Professional it always gives me the same error.

  Suggestions for the configuration of the BIOS or solutions for why this is happening?

  Thanks in advance.

  Hello

  Just a question:
  You are looking for in this forum for other similar issues with regard to the installation of Win XP and lack HARD drive? I doubt

  The fact is that your notebook has a SATA controller and you need a SATA (Intel Matrix Storage Manager) driver.

  You should have a look here in this doc from Toshiba:
  [How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

  and should also search this forum for other threads

  Good bye

• Satellite A30 PSA30E - BIOS does not recognize the HARD drive

  Hi all
  I have a Satellite A30 (PSA30E) and I start the computer. When I enter the BIOS it does not recognize the hard drive.
  Does anyone no what I can do?
  Is it possible to restore the BIOS?

  Thank you

  Hello

  You replaced the HARD drive by a new one or the BIOS don't recognize the old HDD?

  Usually if the laptop is not able to start and that the BIOS does not see the old HDD then I guess that the HARD drive is faulty.
  If the BIOS doesn't recognize the inserted new HARD drive and then either you ve bought is not compatible, or the size of the HARD drive is just too big.

  Please provide more info. You see error messages?

• HP Solution Center does not recognize the network printer

  Network has a hp 309 a printer, can print from the computer, the problem is:

  HP Solution Center not load-says incomplete installation.  If I plug in the USB cable and let it continue, it sets up a second printer that only works on the USB cable and it still does not recognize the network printer.

  Question how can I get the Hp solution program to reward the network printer.  If I reload the CD, then reinstall the will other people on the network of the problems?

  Resettlement on your machine won't affect only you, no other machines on the network.

• Recovery Manager HP does not recognize my flash drive!

  My computer is HP Pavilion p6 desktop computer - 2317c, running windows 8.

  I am trying to create a recovery media and have a 32 facet of Cruzer Sandisk of Go that I intended to use for this. Unfortunately, Recovery manager does not recognize the flash drive... it never appears in the menu at all. The drive appears when I click on the computer icon in the section files, with no problems at all, as you can see.

  

  I have not created a game of recovery media, and it shows not enough space error, he just lets it appear at all!

  What can I do to fix this? I really want to do a recovery set, to prepare for a visit to the demon responsible for foulups visit.

  Hi Savvy2,

  SanDisk has changed the firmware in their most recent products so that the USB appears as a local drive and not as a removal media device. Keys older HP Recovery Manager on this information, and that's why the HP Recovery Manager is not recognized your USB key.  Review of the information that has been compiled by Erico below.

  Success

  Transcend 16 GB 3.0 USB

  Team F108 64 G Group (reported as a success by Big_Dave)

  PNY Turbo 3.0 - 32 GB

  Lexar Jumpdrive M10 sure 64GB USB 3.0

  Patriot anger 3.0 32 GB

  Failure

  Kingston DataTraveler 100 32 GB G3

  Kingston DT R3.0 USB 3.0 32 GB

  The Pro ADATA s102 - 32GB USB 3.0

  SanDisk Extreme 32 GB 3.0
  SanDisk Cruzer Blade USB 2.0 Flash Drive 32GB

• Computer does not recognize my Flash drive or application to be open.

  Original title: usb not recognized

  My computer does not recognize my Flash drive or application to be open. However, I cannot hear the sound produced when something is connected.

  Hello Miss beautiful,

  1. are you facing problems with USB devices?

  2. did you of recent changes on the system?

  You can read the following article and check if it helps.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

  Important: The above link contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

• Lost in car-Windows xp does not recognize the slave drive

  I do reinstall xp home, no problem when I did the system does not recognize the slave drive I have.  As far as I can tell that it's all hooked up correctly.  When I go into disk management it does not recognize the drive either.  All of the suggestions.

  Hi james.williams,

  1. How is the drive connected to the computer?
  2. What is the number of the brand and model of the player?

  I suggest that you check the jumper settings and make sure that the jumpers are correctly positioned.

  Make sure they are in the two master/slave jumper and not cable select.

• does not recognize the flash drive. I get a code 28, pilot not available and the code 19 registry damaged. How to solve this problem?

  Original title: Pny flash drive problems

  I used my flash drives on my pc with xp as os without problem. I then took the same flash drive for my laptop with the windows operating system 7, I opened the files. Then I went to the computer with xp, and the pc does not recognize the flash drive. I get a code 28, pilot not available and the code 19 registry damaged. How to solve this problem?

  Hello

  Do you see these error codes in Device Manager?

  Plug the flash drive and run the Fixit of the article below and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/

  See also the section below, which might be useful in solving the problems of USB devices.
  Advanced troubleshooting tips for General USB for Windows XP problems
  http://support.Microsoft.com/kb/310575

• Western Digital WD10EARS internal hard drive Caviar Green 1 TB - my system does not recognize the new drive

  I recently bought a computer Dell 4700 to a friend with Windows XP installed. I've updated the memory to 2 GB and now seeks to install a WD10EARS 1 TB harddrive. The new works of fine memory is not the hard drive. My system does not recognize the new drive. I contacted WD for help and they told me to try diferent rider combinations that were Jumper 1-2 and 5-6, still does not work, I checked the hardware compatibility list and he said he would start uo without modification. This isn't. I would be very greatlyful for any suggestions, to HELP!

  I've had several people tried to help me solve my problem. They were all, I thought, more than I am computer savvy. As time progressed, solutions became more complex. After they all left without resolution I thought and it appeared to me that the simplest solution might be correct. One person had checked. I turned on the computer and when the Dell logo came I pushed the F12 key to open the Dell configuration screen. The drive on which the new drive has been installed has NOT been activated! Duh! I activated the he and the program Acronis recognized and everything went like clockwork after that. Phew! What relief! Thank you for your comments I am just glad that my problem it doesn't require resolution. Are Mod

• my pc does not recognize the cd drive. I tried restoring the system without success.

  Windows does not recognize the cd drive

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• NSLU2 does not recognize the hard drive

  Hello

  I have a NSLU2 on Win XP SP3.

  It does not recognize the USB drives, he wrote that 'drive not formatted '. It only recognizes the USB key as "disk2".

  Current firmware is V2.3R29.

  When I try to update the firmware, the "not enough disk space" message.

  I tried the same disc on a different NSLU2 and it worked fine.

  What can I do my NSLU2 reading displays the disc correctly?

  Thank you very much for your help!

  Markus

  It seems to be a firmware issue... The V2.3R29 firmware. is quite old. The latest firmware is Ver.2.3R63... Hard reset the NSLU2, power cycle it and then try to update the firmware. After upgrading the firmware, reset it again and reconfigure... Disconnect the HARD drive before upgrading.