Device not detected; Installation of the dll Qt.Declarative 4.

Similar Questions

• Device not detected, I lost the sound. It is said that the material change

  original title: device not detected

  Hello! I have Dell Inspiron 1545e and I lost the sound. It is said that the material change. But I looked at the problem. But it only shows the hardware changes. Please I need help.

  Hello! I have Dell Inspiron 1545e and I lost the sound. It is said that the material change. But I looked at the problem. But it only shows the hardware changes. Please I need help.

  Have you visited the suport Dell and drivers download page for your system (by serial number would be better) and download the driver for audio and install it?

• Device not detected, I copied the Diagonstic report file...

  I copied the Diagonstic report file.  It shows me:

  Win32_PNPEntity.DeviceID="ACPI\\ENE0201\\3&11583659&0".

  the following line of Code ConfigManagerError (red flag)

  the following line: ConfigManagerUserConfig 0

  the last line: status: error

  This is a FEATURE 'UNKNOWN '.

  Ben Berzins

  http://support.Lenovo.com/en_GB/downloads/default.page? #

  There are a number of models Y550, you should have a shortcut of Lenovo desktop update

• O2 dongle is never to step of the password and then just says device not detected / found

  Original title: im trying to use my o2 dongle to connect to the internet, but for some reason some he used to let me...

  Ive connected the dongle and it goes through the normal treatment it says connection. However, it's never at the stage of the password and then just says device not detected / found

  Hello

  You can try to reinstall the USB controllers and check.

  a. Click Start and type devmgmt.msc and then click OK.

  b. expand Bus USB controllers.

  Note: You will need to scroll down to find this point.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  f. check the device to see if it works.

  You can also consult the following link:

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Hope this information is helpful

• Samsung Galaxy - device not detected. ERRO - unknown device

  Original title: Samsung Galaxy - device not detected

  I have a samsung Galaxy ace and my pc does not detect. He said that the controlprogram is not installed and I can't install it, my pc says its and unknown device...

  Hello

  1 have had any changes made on the computer before the show?

  2 have you installed the software for the Samsung Galaxy Ace?

  3. the device was working fine on the computer as soon as possible?

  4. are you face any problem with the installation of the program Samsung?

  Method 1:

  I suggest you to refer to article and install the software on the computer and check if it helps.

  http://www.Samsung.com/hk_en/consumer/mobile/mobile-phones/Smartphone/gt-S5830OKATGY/index.idx?PAGETYPE=prd_detail&tab=support

  Method 2:

  Check the link and see if it helps:

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

• Linksys wusb100 device not detected-'Code 43'

  Original title: linksys wusb100 device not detected

  I am running windows 7 64 bit I have a Linksys WUSB100 the error I get is Windows has stopped this device because it has reported problems. (Code 43) I think that the device does not work in windows 7 any idea out there

  Hello

  1. Have you made changes on the computer before this problem?
  2. He previously worked?
  3. Have you installed device driver oon your computer?

  I suggest you try these methods and check the status of the issue.

  Method 1:

  Run the facilities of diagnostic tool do not work or are not detected in Windows

  Hardware devices do not work or are not detected in Windows.

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 2:

  Update a hardware driver that is not working properly.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3:

  Uninstall the device driver, download the latest driver by downloading from the website of the manufacturer of the device, install on your computer and check the status of the issue.

  a. click the Start button, select Control Panel, click System and Maintenance and then click Device Manager.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
   
  b. in the list, double-click the type of device and then look for the specific device that is not working properly.
   
  If an exclamation point appears next to the device name, Device Manager cannot find the device driver. Go to "Use Windows Update to find a device driver."
   
  If no exclamation point appears next to the name of the device, go to "uninstall and reinstall the driver for the device."

• ATI Theater 650 Pro digital tuner not detected / installation in Media Center

  I have Vista Ultimate 64 with SP2 and an ATI Theater 650 Pro with the latest driver installed ATI. Media Center does not detect and configure the digital tuner, only analog (tuner works very well - get all analog and digital - channels in Win7 RC). Other tuners were detected drink they will not set up due to missing or inconsistent signals connected to them. I have installed ALL the ATI driver available in turn, including Dell (card/system provider). I reinstalled windows several times (at the request of Dell). The tuner has attempted without ever addressing the digital and cable HDTV signals. It worked the first time, in Win 7 RC.

  Someone at - it a way to make this work? Thank you!

  Hi Carl,

  What is you receive the exact error message?

  I suggest you try the following steps:

  Step 1: Change the Windows Media Center Receiver Service to a specific to a Local System account account name:

  1. click on start-run, type services.msc, the, click OK.

  "2. when loads Services window, navigate to the" " " Windows Media Center Receiver Service ', double click on it to open it,

  3. click on the tab connection , and then select the Local System account.

  4. click on ""apply ', then OK on Services of warning message. "

  5 restart the computer. Click OK again, and then restart the computer

  Now check if the problem is resolved.

  Step 2: Disable the security software and update the driver for DELL motherboard chipset

   

  http://support.Dell.com/support/downloads/index.aspx

   

  To disable the security software, follow the steps mentioned below

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Important: Activate security software once everything is done.

  For more information, see the link below:

  What should I know before adding TV to use with tuners Windows Media Center?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-should-I-know-before-adding-TV-tuners-to-use-with-Windows-Media-Center

  Set up a TV signal in Windows Media Center

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-TV-signal-in-Windows-Media-Center

  TV on your computer: understanding signals TV and TV tuners

  http://Windows.Microsoft.com/en-us/Windows-Vista/TV-on-your-computer-understanding-TV-signals-and-TV-tuners

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• During the installation of an update for Skype get device not detected DirectX error

  Original title: is no longer detected device DirectX

  When you install an update to Skype, it crashed (and does so every time I have install and reinstall) peripheral suitor DirectX not detected.  Someone knows what to do?

  Hello

  ·         The issue is only with Skype?

  ·         What operating system do you use?

  I suggest you to contact the Skype support for any known problem connects to the update of Skype.

  https://support.Skype.com/

  See also:

  Diagnosing basic problems with DirectX

  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-basic-problems-with-DirectX

   

  Run the DirectX Diagnostic tool

  http://Windows.Microsoft.com/en-us/Windows-Vista/run-DirectX-Diagnostic-tool

• X121e Bluetooth device not detected

  Hello, I just got a new Thinkpad X121e (the one with 1.3 GHz i3 CPU). I tried to get the Bluetooth in Windows 7, but the driver gives me an error message during the installation my Bluetooth device is not detected. Bluetooth is enabled in the Bios. Everything else, including WiFi, works without problem. What kind of device is built in this kind of Thinkpad's Bluetooth? Are there other measures I could try to fix this?

  I found the solution: the necessary tool is included in the "lenovo power management. Now I turn on Bluetooth with Fn + F5 and it works as expected. Also when you use the ThinkVantage System Update software, it was possible to install the Bluetooth tools when Bluetooth is turned off. Which was not possible, by directly downloading the Bluetooth software.

• Bluetooth device not detected - HP Pavilion G6-1139TX

  Yesterday (January 7, 2012), I bought a HP Pavilion G6-1139TX. I installed Windows 7 (32 bit). Everything installed properly, but the system does not detect the Bluetooth device. When I try to install the software/driver Bluetooth that is "Broadcom 2070 Bluetooth", it gives me error "No. BLUETOOTH DEVICE CONNECTED/DETECTED" and abandonment of the installation. Same Bluetooth switch is on. In Device Manager there is a yellow question mark with the code "BCM20702A0". Please guide me what is the problem and how to fix this problem. What's the problem in hardware or something else?  For your information, a Wi - Fi connection works correctly.

  I had the same problem Bro too. Here's what I did,

  Google code as 'BCM20702A0 driver '. Then try to catch the driveridentifier site link (sorry bro m not at home to provide you with exact link.m via my phone right nw.) Just saw your message and Thoth to answer with what I know). Then, there will be a link to download not only bcm2070 pilot but also any blutooth broadcom drivers.

  * Download the package. It will be like 100-150 mb. CNT remember exactly. And don't forget to check that your hardware ID list. You can get that from Device Manager. And neglect even if the site mentioned another computer brand.not hp.
  * install the pack, and then restart the laptop.
  * After this, return to Device Manager and go to the properties of the bluetooth driver. (the one with the yellow exclamation point. I hope you know how to do and do not forget to activate the wireless cnction otherwise it wouldn't show up there)

  * in the Properties window, go to the update driver and click on the button browse my computer for driver.
  Then select bluetooth, then broadcom adapters and I remember select bluetooth 3.0 HS... blah... blah... it will be a lot like that. But try to choose a simple. It still works.
  * to transfer files, I s\u0026 an incompatibility with the windows utility. Then first pair your device. Then use Obex Commander. Its a free app and I find it more useful to use.

  That's it bro.

• Devices not detected after Windows 7 (Downgrade Up)

  My ex has a brand new HP 15 - g012dx provided with Windows 8, but has driver support for Win7 x 64.

  She has all the driver files, but none will install; they do not have the Setup installers I can say. There is no driver chipset, so automatic PNP/detection will not work. So, how can I install them manually? Essentially, I unzipped the one-at-a-time to a folder. It has Windows 7 x 64 Edition.

  You are the very welcome.

  When you run the file, decompresses it and usually the default directory of the driver unpacks to East C:\SWSetup\spXXXXX where XXXXX is the number of the file download.

  Then, a Setup screen should automatically pop up and let you know which driver is installed and you follow the instructions on the screen.

  To install manually a driver W7 after running the driver by which file above, you close out of the installation dialog box.

  Go to Device Manager, click the device that you are installing the driver, click on the driver tab, click on put up-to-date driver, select travel it my computer for software driver and browse to folder applicable drivers.

  Make sure the box include subfolders is installed and must install the driver.

  There are a few riders where you can't do this and you must let the autorun driver because there is no setup informatiion files in the pack of drivers that you can see or extract.

• My HP 3 year all-in-one C4280 shows USB not connected and "device not detected.

  Everything works OK until a few weeks ago. I uninstalled reinstalled. During the installation, there is a message' device detected"and then at the end of"device not found ".

  Also USB not connected. Switched USB to another port, nothing helps. Contacted HP.com.I running Vista Home Premium SP2. This is my last ditch attempt to resolve. Is this a problem with Vista?

  Hello

  I suggest you try to run the Microsoft Fixit from this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  It will be useful.

• recovered XP (fully updated) will not complete installation of the software of HP officejet j6480

  The test report of wireless since installation of the printer indicates everything should be good, however, the installation of the officejet software never ends siaying may not detect the printer wireless. The test report the router and the printer are okay.

  I did not use to have Avast! Kaspersky Anti-virus when this same problem (pc recovery and al.) who has spent 9 months ago.

  My Fios Actiontec router shows the printer on the WiFi network is-, but it does not print!

  Hello

  Try to install the drivers of printer using DVD connected via a cable, and then try to configure the same wireless network.

• importing video WMM-"video capture device not detected...". »

  try to import my movies from my canon camcorder. When I try to import into WMM I get this error "a video capture device it not detected. check a device is turned on and connected to the computer correctly. I use my usb cable that I use with my canon photo camera. It allows to work with two cameras, now he's going to transfer the images from the camera but I get nothing of the video camera. do I need a driver? or a new usb cable for the video camera?

  When I try to import to corel DVD maker I get "no capture driver is available in the system.

  try to import my movies from my canon camcorder. When I try to import into WMM I get this error "a video capture device it not detected. check a device is turned on and connected to the computer correctly. I use my usb cable that I use with my canon photo camera. It allows to work with two cameras, now he's going to transfer the images from the camera but I get nothing of the video camera. do I need a driver? or a new usb cable for the video camera?

  When I try to import to corel DVD maker I get "no capture driver is available in the system.

  ========================================
  What is the model of your Canon camcorder? If records to
  media other than mini DV tapes, it will not import into Movie Maker.

  Also... USB is not the best method to download... Movie Maker
  has been designed to work with FireWire.

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Windows 7 - "USB device not recognized" - to load the new electronic Cigarette device. Help, please?

  I have Windows 7 Home Premium.  I just bought a unit of the electronic cigarette, manufacturer is "Innokin Cool Fire IV", the usb charger plugged on Acer laptop and comes to the screen "USB device not recognized".  I loaded different brand before without problem, I don't know what to do and I am NOT GOOD WITH COMPUTERS!  My settings are at "install updates automatically" and I DON'T WANT WINDOWS 10!  Can someone help me please?  Thank you for taking the time to read this.

  This seems to indicate that the charger has actually been detected as a device, but Windows can not work it out.

  Normally such a device should only connect to 5v and 0v pins and have no connection with the pins of data, in this way, that it will not be seen by Windows. I would be concerned by the quality of the device if it has some form of data connection. If you want to continue with this charger, that I would recommend to use a power supply of 5v USB instead of risking the USB port of the laptop, a lot less expensive if it does not. It has been reported several eCig Chargers catch fire. Something like this: