Device simulated in MAX, auto test without error and has work Test panels, but is not displayed in the DAQ assistant.

Similar Questions

• 201003-error occurred in the DAQ Assistant

  Hello. I use "cDAQ-9178" and "NI 9215" and "NEITHER 9402" are added on. "

  However, when I run Labview code, "Error-201003" occurs.

  {

  Device not available. Possible causes:

  Device is no longer present in the system / device is not powered.

  Device is turned on, but was temporarily without electricity / device is damaged

  }

  (Error appears as the 1st and 2nd figures below).

  (Plans of logic is the figure below).

  Thank you.

  I could be something with the pilot

  Check this box:

  Error 201003 to the MAX test panel or all by running the DAQ Assistant

  http://digital.NI.com/public.nsf/allkb/5413F392D88326148625746B006745C5

  In this forum, they speak the same error:

  Spontaneous error code 201003 for acquisition of data PCI configuration

  http://forums.NI.com/T5/SignalExpress/spontaneous-error-code-201003-for-PCI-DAQ-Setup/TD-p/830707

• No device supported in the DAQ assistant

  Hi all

  I use the scanner high speed (NI 5922). I installed Labview 8.5.1, then the software scope OR the digitizer NI 5922 high of speed, then the hardware driver. I tested the DAQmx with the MAX and it passes the test. But when I started to use the labview with the DAQ assistant, as described in the manuals I have not found all devices supported! Should I log a physical device to the hardware driver channels or what should I do?

  Thank you

  Ibrahim

  The 5922 is supported by NO-Scope http://www.ni.com/digitizers/software.htm and not by DAQmx. This page should help you get started.

• Simulate signals wired to the DAQ assistant for USB-6009 device

  Hello

  I'm trying to send a signal to the DAQ Assistant Express VI.  I watched the movie "Generating a Signal" on the Web site of NOR (www.ni.com/academic/students/learnlabview/generate.htm) and I have my Signal simulate connected directly on the DAQ Assistant, as shown in this film.  In my case, the DAQ Assistant sends the signal to a device USB-6009.

  However, I received this message:

  Error-200077 occurred to the DAQ Assistant
  Possible reasons:

  Requested value is not supported for this property value. The value of the property may be invalid because it is in conflict with another property.

  Property: SampTimingType
  asked the value: Sample clock
  You select: On-demand

  If I select 'On Demand' in my DAQ assistant and run the vi everything works beautifully.  However, I need my DAQ assistant to be configured to generate a waveform AC continuous, not output a single alternating current rippling.

  What happens here?  I did not have this problem before on other devices of NOR. I am using LABView 2010.

  Please answer.

  Thank you.

  double post

• Error of the DAQ Assistant

  I've just updated LV 2009 SP1 LV 2010. I use a LV 32-bit on a 64-bit computer.

  When I open the DAQ Assistant, I get a pop up window that says "LabVIEW: an exception occurred in the external code that is called by a function of the call library node."  This could have corrupted memory of LabVIEW.  Save all work to a new location and restart LabVIEW.  VI "Advanced Timing.vi:1" was arrested in node "" a call to "get of DAQmxAssitant_DAQmx IO Info.vi of control.

  If I hit OK, DAQ Assistant is locked up, if I use the Task Manager to close the LabVIEW vi breaks down.

  I already reinstalled 9.5.1 DAQ device drive. without success.

  There is no such version. The most recent is 9.2.2.

• Error 0 x 80070522: A required privilege is not held by the customer

  When I try to save, copy paste, delete any document to my C:\ drive I get this error.
  Error 0 x 80070522: A required privilege is not held by the customer

  Here, http://www.sevenforums.com/hardware-devices/265615-creating-new-file-c-drive-gives-error-0x80070522.html

• VMware Fusion has encountered an error and has stopped Windows.

  Summary:

  I started experiencing this problem in November and was beaten on that since including using the VMware support and Apple support.

  Full of the message in the virtual machine window:

  = VMware Fusion has encountered an error and has stopped

  = bottom of Windows.

  ====

  = Click on restart Windows to start Windows again.  Click report for

  = collect and request the support of VMware.

  ====

  = < ignore > < report... > < Windows restart >

  By clicking < report... > generates the report

  Clicking on < reboot Windows > hangs the system.

  Various VMware Fusion, Virtual Machine commands do nothing.

  Again, only way I found to get there is to Apple, Force Quit of VMware Fusion.

  Two systems in question, iMac and MacBook.

  Familiar to anyone else?

  Details: =.

  The two systems were very well work well on several years.

  Status of starting point was.

  -iMac and MacBook running VMware without any problems for several years.

  -This includes several updates to Mac OS and VMware Fusion.

  -OS X 10.9.5 on both systems with the latest upgrades.

  -VMware Fusion 6 on all systems with the latest upgrades.

  -Virtual Machines on two almost identical systems - Windows 7, all derivatives of a VM database.

  
  

  Problem started only on iMac.

  
  

  In weeks, with the encouragement of support VMware and Apple have updated to Yosemite, installed VMware Fusion 7 and built Windows 8.1 scratch machines.

  
  

  Problem now happening on both systems with MacBook, stay alive for about 15 minutes and iMac may be several hours.

  Any ideas appreciated.

  Thank you.

  Paul

  In summary...

  This problem was initially detected on iMac and MacBook:

  Mavericks

  Fusion 6.x

  Windows 7

  The ultimate resolution iMac and MacBook:

  Yosemite

  Fusion 7.1.1

  Windows 8.1

  Details of the way pick up what 7.1.0 merger was in place for the ultimate resolution in the chat messages.

• upgrade to windows 10, cannot open itunes, it opened the first time, and imported all my songs, but does not open a second time, get the error that the path is not correct and file not found

  upgrade to windows 10, cannot open itunes, it opened the first time, and imported all my songs, but does not open a second time, get the error that the path is not correct and file not found

  Try to repair the security permissions for iTunes for Windows and the empty/corrupted after upgrade/crash iTunes library.

  TT2

• I double clicked on update of programs and I wonder now run a legacy cpl high. When I click ok it says script errors and nothing works.

  original title: run a legacy cpl high?

  Hi all. on my control panel I double clicked on update of programs and I wonder now run a legacy cpl high. When I click ok it says script errors and nothing works. If I click on details until I click on continue it says; "C:\Windows\System32\RunLegacyCPLElevated.exe" Shell32.dll, Control_RunDLL "C:\Windows\system32\ISUSPM.cpl",Program updates I'm not very technical and well I tried to look on the search engines, I can't find anything to help me.

  Hope someone can advise me please

  Thank you aypee74

  I figured how to stop my warning high. I just got an answer and it reminded me that I now know why my computer was giving this prompt. This may help a bit there. So I decided to write.

  In my case it was my 'Sigmatel Audio Control Panel.
  I had disabled "allow reconfiguration pop ups".
  This will make the warning "Run a legacy CPL high" lights up to chance that your system can access this audio program. Once I've rechecked. The warnings went away unless I open the control panel. But it's a normal warning according to the manufacturer of my computer.
  Some of you may have something much more serious, but for the few who becomes confused by the latter and have this audio driver, this may help.

• My wireless router does not appear when I shoot to the top of my devices. It shows my fax, modem, scanner and a few others. But not my belkin wireless.

  My wireless router does not appear when I shoot to the top of my devices. It shows my fax, modem, scanner and a few others. But not my belkin wireless. And when I try to add it, the system can't find it. Please help

  Belkin support for your model, for installation instructions.

  Your router will not appear in the devices

• WINDOWS 8 - error 0 x 80070522: A required privilege is not held by the customer

  When I try to copy a file to a flash drive for my C:\ drive I get this error.
  Error 0 x 80070522: A required privilege is not held by the customer

  How can I solve this problem?

  Hi guys

  You must completely disable UAC. This is done in the registry.
  Click Start > run > regedit. Make a backup of the registry first to be safe.
  Navigate to the path below and change the DWORD 0
  HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Policies\System, EnableLUA and value0

  It worked for me

• ???  I just installed Lightroom 5 from Amazon for my Mac with 10.10.1 software.  When I open it I get: "an error occurred when attempting to change modules.  It will not import pictures and has no side panels under the library.  What should I do?

  I just installed Lightroom 5 from Amazon for my Mac with 10.10.1 software.  When I open it I get: "an error occurred when attempting to change modules.  It will not import pictures and has no side panels under the library.  What should I do?

  Error changing modules | Lightroom

• Error (Hex 0xBFFF0015) time-out in NI VISA test panel when you try to play the system

  Hello

  I try to control the position of three valves actuator of four lanes of Garland. They are VICI Valco and model # EUHA. I connected them via RS - 232 to USB in my computer. I was able to communicate with them, when I sent a few simple commands through hyperterminal and when I open MAX devices appear and the sign says the devices are working properly. However, when I go in the test panel and try to run some of the default commands, I get timeout error, 0xBFFF0015, during the reading of the order. Thanks for any help you can provide.

  To get your LabVIEW code, you right-click on the control/string constant and select '-' display Codes?

• HP 8600 will print a test page but does not Word print

  Hello

  My HP 8600 worked very well, but is no longer allows to print from Word. It will print when I go to the HP page to test, but not from anywhere else.

  I'm on a Mac OS X.9.5

  I tried to uninstall and reinstall.

  Thank you

  HM, OK, thanks for getting back to me!

  Try power cycling network devices:
  Turn off the printer and the computer and unplug the router for 1 minute (do not press the buttons on the router).
  Plug the router back in and wait another minute, and then turn on the printer and the computer and test print.

• 2 problems: code 80070424 error and a message saying that I am not under a copy is authentic.

  Out of the blue, I get a message in the corner of my screen, "Windows 7 Build 7601, this copy of Windows is not genuine." All day, I tried Microsoft solutions without success. At the same time, I got a window that asked my product ID, and I used the 25-digit Microsoft label on my computer. The ID was dismissed as unfounded. Long story short, I got the key product using Belarc and its different from that on the label, but it's correct. I know because Microsoft, I learned the last 10 digits and it matches. Now I can not find the Microsoft page requesting my product ID. I don't have the option, click Start, right-click computer, click Properties and activate. It says unavailable.

  Second problem that my being the result of the first, when I use the update of the window, I get the error code 80070424. I tried all the solutions on the Microsoft Web site, and I feel like a dog chasing its tail. I downloaded all Fixit and even said that it is not a problem with the Update window. When I click on windows update, I get the message "you may be victim of software counterfeiting. My computer is a gateway and Windows 7 has been factory-installed by Acer.
   
  Of you techies light allows an old man to solve these problems?
  Jerry

  Hello

   
  Thanks for posting of application on Microsoft Community.
   
  According to the information you have given it seems that you are not able to run Windows Update as a result of not being able to activate Windows. Therefore logically first difficulty
  the problem of activation and then work on Windows updates.
  As you say "at a time given, I got a window that asked my product ID, and I used the 25-digit Microsoft label on my computer." The ID was rejected as unfounded". I wish to inform you that a product ID is different from the product key. If you receive an activation window then in order to validate the window you must enter the product key 25 digits.
  The 20-character product * ID * is created during the installation and displays highlight down (in the Activation section) on the opening window resulting Panel right click on the computer icon and select 'Properties' from the context menu. It is used to get/qualify for technical support (limited though it may be) of Microsoft; It is of no use during the installation process.
  25 character product * key * is used to 'prove' ownership of a license is necessary to perform the installation and is either stored on the DVD packaging on a sticker that says "Don't lose that number", or on a certificate of authenticity (CoA) label
  for an OEM computer.
  To access the window of Activation of Windows, follow these steps:
  1. Click Start
  2. Type slui.exe and press ENTER.
  3. You will see the Windows Activation window
  4. Enter the 25-character product key and try to activate Windows.

  See also the suggestions of Keith - on April 30, 2010

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/Windows-is-showing-as-not-genuine/cbd43297-0e4d-458C-8487-9168c4cd668d
   

  Error "Windows is not genuine" in Windows 7 or Windows Server 2008 R2

  http://support.Microsoft.com/kb/2704233

  Note: Above the method contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  For the problem with Windows Update, I suggest you refer to the article below:

  Windows Update error 80070424

  http://Windows.Microsoft.com/en-us/Windows/Windows-Update-error-80070424#1TC=Windows-7

  Additional reference:

  Genuine Windows: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows/help/genuine/FAQ

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.