Device USB ATA/ATAPI Bridge are representatives

Similar Questions

• IDE ATA/ATAPI controllers does not, unable to TRIM SSD

  I'm having a problem with my newly installed SSD. I just got an Alienware Aurora R4 with Windows 8. I immediately cloned the HDD to a vector of OCZ serving 256 GB drive of EaseUs ToDo Backup, which worked perfectly when I just upgraded to an SSD on my laptop. At the beginning I had a problem with recognition by car, but then ensured this bios was set to AHCI and UEFI and finally to load Windows 8. I reformatted the hard drive 2 TB for Data (d :)) and loaded all my music, videos etc..) Then when I went to optimize my readers, I clicked on the optimization of the DDI, and she went from needing optimization to "optimization is not available" - which it is said now and is gray. I realized that it is a question as optimization in Win 8 on an active SSD TRIM (works on my laptop).  Do not know if it is a matter of concern, but the (I'm sure that what is already hidden) partition DIAGS on the original drive received a drive letter (e :)) on the SSD.

  Anyway back to the no optimization/TRIM. My first reaction was to google "Value is not available" and I found this link.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-performance/when-i-try-to-optimize-drives-i-get-optimization/20a45c49-a774-42B1-8317-20ef7799b6ad

  The poster says he fixed his problem by updating its storage controller drivers. "Basically, I downloaded the latest drivers Intel Rapid Storage Technology for Windows 8."
  I checked my control of storage drivers in Device Manager, and these are listed:

  Intel (r) 600 Series chipset SATA AHCI controller
  Microsoft storage controller

  Read more in the article someone else with a similar problem mentioned tried using the admin command promp to activate the TRIM (what to me then tried and had the exact same message of error/result), with the following results:

  Type "defrag c:/l '.

  Coating invoking the name of the drive (C :)...)

  Lining: 100% full.

  The requested operation is not supported by the hardware of the volume. (0x8900002A)

  This individual, and then upgraded to Windows 8 and leaves choose drivers and apparently its has started working. He mentioned its IDE ATA/ATAPI Controller amended in both disk management. Reading that I decided to see what mine were and noticed that I have not yet to IDE ATA/ATAPI controller listed in disk management on my system! Even when the control to display hidden is not a controller to IDE ATA/ATAPI list. Should I do this?

  I went to the controller driver dell to check to see if I needed updates. It shows me only Windows 7 updates as it says that my R4 Aurora accompanies when I added my service code (is there a way to fix this?). I just chose to watch an empty Arurora R4 and was able to see the drivers of Windows 8 and downloaded all updates that seemed relevant (also update bios to A07 A06). When I downloaded the class Serial ATA driver (7D9TS) and you click Update, it says just the file is decompressed, but have not installed anywhere (unlike the other pilots).

  If anyone knows why I don't have IDE ATA/ATAPI listed and how to get this device?

  For those who have an SSD on their Aurora R4 with Win 8 are you able to optimize and what drivers you have this affect it?

  What are the latest drivers Intel Rapid Storage Technology for Windows 8 and how do I know if I have same Intel Rapid storage available?

  Thank you very much. Sorry the length, but I wanted to be as detailed as possible.

  SUTEKH

  I'm having a problem with my newly installed SSD. I just got an Alienware Aurora R4 with Windows 8. I immediately cloned the HDD to a vector of OCZ drive 256 GB using EaseUs ToDo Backup,

  I think that the problems started here, on this stage of EaseUs.

  I hope that you always have this original Image backup... probably on an external USB or something. Good... Keep this forever (especially since it looks like that delete you the original copy/drive).

  You have to clean install Win - 8 (and support adequate and other drivers chipset) this SSD so you can check the materials. It is not easy because of no victory-8 media and hidden serial OEM key. You may need to talk with Dell for some OEM DVD or USB Flash media.

  Personally, I would have also created the Dell 16 GB USB Flash device recovery initially. It might be useful now. He could have facilitated a full restore of your OEM-Windows-8... same "bare metal" (to your Virgin SSD).

• burner not found disk (itunes) IDE ATA/ATAPI driver and found subcomponents

  iTunes keeps popping up with not found disc burner. One of the help pages supposed to go on computer, right click / Manage / device driver / and find the IDE ATA/ATAPI and it wasn't there. so I checked it on my laptop which is windows too, but shows IDE ATA/ATAPI. What should I do now? What is my problem I-tunes?

  Hello

  Sometimes they have too many programs for CD/DVD (burning and reading) causes conflicts that can cause a
  strange as errors they are competing for resources. The problems of corruption and the system hardware could also
  also be at fault.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  --------------------

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• No IDE ATA/ATAPI

  I have brand new m9441 Vista 64 bit. When I look in Device Manager, there is no IDE ATA/ATAPI entry! Is this normal?

  SATA has replaced the IDE / ATA. It's faster and you no longer have to deal with the giant band inside the computer.

• Satellite A660 - USB 2.0 ports are inadmissible

  My laptop series Satellite A660 is a month old and worked fine so far. However, I turned on the machine and all the three Ports USB 2.0 are inadmissible. I Shut Down and restarted the computer - no change.

  (Windows 7-16 Bit OS) Control Panel - manage devices - it is said that all USB Ports 2.0 are recognized and working. In fact, NO device in one of the three (3) USB2.0 Ports are actually be recognized or working at all - there is no answer. Interestingly, the port eSATA/USB combo of 1 one works and responds correctly.

  Can anyone help?

  Should I just send it was pushing the shop? Yes, it's still under warranty.

  Hey,.

  > Should I just send it was pushing the shop?
  No, I think that it s just a USB driver problem.

  In your case I would reinstall the chipset of the official website of Toshiba driver. Also, you have the latest version, try to reinstall it because it contains the USB drivers and maybe it's something wrong with her s.

  After installation of the chipset driver test it again. If it doesn t work to remove all the USB ports on the Device Manager and restart your laptop. The USB ports will be reinstalled automatically.

  What version of BIOS you have installed?

• Trying to simulate the device USB-6366 (without success)

  I read through the tutorials DAQmx and MAX about the simulation of the device, but I can't yet find a way to effectively simulate the acquisition and generation of a signal using a device USB-OR-6366.

  I am a (given at the entrance of this VI) signal using DAQmx Write and then use DAQmx Read to read the signal captured from the internal memory of the card (which has a buffer of 32 MS). To do this, I created a task with DAQmx I feed in the writing block.

  I know that the approach is most likely wrong, but I can't understand not just how to do this in a simple way and documentation of NOR is anything but simple. All I want is to

  (a) test using 2 digital inputs to capture this signal by the device and then read what she has gained from its internal buffer

  (b) send the same signal to 2 digital outputs the signal output again.

  See you soon

  Yes! the simulation is designed to allow you to write a program and check that it works theoretically even if you do not have the material physically available. It has no interface programming to influence on the what the reading functions will return simulated data. And write the function has no notable effect anywhere, working as a receiver of data in nirvana. It is always useful because you can test software without getting all kinds of errors on the non existing hardware access attempt, but it has its limits, of course. However, a programming interface for manipulating that which and how the data are simulated, while it would be a very interesting feature, is almost certainly to complicated not only to implement but also to use.

• DRIVERS CONTROLLERS ATA/ATAPI IDE that I use windows 7 of the month last on a laptop HP PAVILION g7-1279dx

  Help

  Hi @stevewalters

  Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I saw your post about some kind of problem with the ATA/ATAPi IDE controller drivers. There is no specific drivers listed on the page of the driver for your model. Here is a third-party link that will show you how to upgrade your drivers from the Device Manager.

• Meaning of the States LED tricolor on device USB-232

  It's more curiosity, rather than a problem.  I noticed that the devices USB-232/4 most recently bought that we have received seem to now have the status of Panel before LED that show * 3 * States (4 If you include "LED off"!) - yellow, green and Red now.

  I have not found anything whether in literature online to describe something as mundane as what led.  I always assumed that yellow and green are the indicators of mark/space.  Sometimes now they light up briefly in red, but I have not found to correlate to any abnormal operation.

  What is happening with this?

  Dave

  Hi David,

  I found the following page in help OR Serial.

  

  I hope that answers your question!

  Thank you

  Scott M.

• device USB 43 error code

  Ive got a didital nine unused usb just lost the manual photo frame, ive plugged into my laptop and windows tells me there is a problem with it (code 43) what is the code 43 and what can I do to use my unit ive tried updating drivers and it still says theres an error please help! Thank you

  Hi Paulwhitaker,

  You can read the following article and try to run the fixit of material.

  Hardware devices do not work or are not detected in Windows

  For more information, you can consult the following article:

  Code 43: Windows has stopped this device because it has reported problems

  Hope this information is useful.

• Device USB-8451 reference and attached device

  I have 2 test systems PC using NI USB-8451 I2C communication.

  A reference device... 33 b... and the other a... 33D..., so I can't use the default fixed values.

  Also, I may need to run an exe have respected for others to use.

  Questions:

  1. it is not VISA. No VISA opening or closing.

  2. nothing in the compare pallete validates this reference of the device.

  3. no USB device attached validation (Are You There).

  Up to now

  1. a successful simple i/o operation can check "Are You There". I chose Dig I/O read a bit.

  2. #1 above also validates the reference of the device.

  Is there a smoother, faster way to do this? Windows operating system does not record stuff USB etc... ?

  TODO:

  Get the device USB-8451 reference in MAX.

  This link may be the solution, I'll know tomorrow. I was expecting a VISA VI to be useful.

  http://forums.NI.com/T5/LabVIEW/how-to-ask-the-I2C-device-alias-name-from-the-Max/TD-p/1231439/highl...

  Jeff

  This seems good.

  Thank you

• HP Pav HPE h8-1300z: LACK of CONTROLLERS IDE ATA/ATAPI!

  Recently I had to reformat my HARD drive using my HP OEM recovery disks. Now when I go into Device Manager, there is no registration for the ATA/ATAPI IDE controller. There is no UNKNOWN devices and there is no OTHER devices listed by eliminating this question. I feel I might need to re Flash my BIOS but there is no ads for this installation of support for my PC software it displays only a BIOS for another MoBo. I was hoping that the recovery disks would have an opportunity to re - install the drivers, but it seems he does only a comeplete OS re - install.

  Is there a way I can install the IDE ATA/ATAPI controllers without having to do a complete OS re - install?

  Your motherboard has a SATA controller and the connectors. There is no IDE connector on the motherboard Angelica2.

  Your PC card

  http://support.HP.com/us-en/product/HP-Pavilion-HPE-H8-desktop-PC-series/5258496/model/5261714/product-info

  

• How can I get updates for IDE ATA / ATAPI Controller for windows xp pro

  Where can I find drivers updates for IDE ATA / ATAPI Controllers for windows xp pro?

  These are usually Microsoft drivers, and they are as old as the hills, why do you need to update the drivers?  If the Microsoft drivers are not appropriate, then get the drivers from the manufacturer of the motherboard.

  John

• Apple Mobile Device USB Driver has not passed Logo testing for compatibility with Windows XP, I ran the suggestion to "fix" 925196 that it still does not work. What can I do else?

  Bought the iPhone 3 g (not 4) trying to run the material but get the following error: Apple Mobile Device USB Driver no has not passed Windows Logo testing to verify compatibility with Windows XP continues the installation of this software may impair or destabilize the functioning of your system.

  Windows XP Service Pack 3 is running.

  I ran the 'Fix - It' 925196 solution, but the problem could not be solved. What is a malware problem?

  Hi deanie3,

  We will check if the following is useful.

  Method 1: Run the next Fixit and check the issue.

  Hardware devices do not work or are not detected in Windows

  Method 2: Follow the steps in the below article mentioned to see if it helps.

  You cannot install some programs or updates

• Said device USB to serial port Manager works, but it is not

  Original title: PL2303 USB to Serial No. GB
  My laptop is running Windows 7. I loaded the drivers PL2303. The Manager of said devices usb-serial comm port works. Set at 9600 baud, 8 No 1 order no flow.
  The GPS is a Garmin etrex Euro software version 2.06. GPS version model 156 206.
  I communicate successfully with the GPS unit via an DB9pin port at the back of my office. 9600 8 No 1 Garmin format.
  When I added the USB cable series to communicate via a usb port the "EasyGPS'program cannot read the GPS.

  I down loaded the PL2303 drivers for my desktop (XP) and the same problem occurs.

  I get the message ' device working properly "for both laptop and desktop."
  There is however no communication to the GPS.
  I tried again via the DB9pin port and communication are OK.

  Any Suggestions
  Thanks, Jim

  Hello

  I suggest you to join easygps helpdesk on this issue.
  www.EasyGPS.com/support.asp

• ds8a25 device, one ata dvd Slimtype not has regconized

  in my settings systems device slimtype dvd a ds8a25 ata are regconized has a match score on top of lable

  Hello

  1 when was the last time it was working fine?

  2. don't you make changes to the computer until the problem occurred?

  3. What is the brand of the DVD player?

  I suggest you to try the steps below and check if it helps.

  Method 1: Try running the Fixit tool from the link below.

  Hardware devices do not work or are not detected in Windows:
  http://support.Microsoft.com/GP/hardware_device_problems

  Method 2: If the problem persists, then try uninstalling and reinstalling the DVD driver in Device Manager.

  a. type devmgmt.msc in the search box start and press ENTER.

  (b) in Device Manager, expand DVD player.

  d. click on uninstall.

  e. restart the computer.

  Pilots should settle automatically after the computer restarts.

  You can also check the manufacturer for an updated driver and install the latest version. See the guidance below mentioned link: http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly

  Hope this information is useful.