Different 'outside_cryptomap access-list"for each VPN?

Similar Questions

• Question of access list for Cisco 1710 performing the 3DES VPN tunnel

  I have a question about the use of access lists in the configuration of a router Cisco 1710 that uses access lists to control traffic through the VPN tunnel.

  For example the following lines in a configuration on the remote router. My question is whether or not the traffic that matches the definition of list access-130 (something other than 192.168.100.0/24), cross the VPN tunnel or go directly to the Ethernet0 interface.

  My understanding is that traffic that matches the access list 120 would be encrypted and sent through the IPSec tunnel. If there was "ban" set out in the statements of 120 access-list, the traffic for those would be sent through the IPSec tunnel but not encrypted (if possible). And finally, given that the definition of crypto card reference only "adapt to 120", any traffic that matches 130 access list would be sent Ethernet0 but not associated with the card encryption and thus not sent through the IPSec tunnel. "

  Any input or assistance would be greatly appreciated.

  Map Test 11 ipsec-isakmp crypto

  ..

  match address 120

  Interface Ethernet0

  ..

  card crypto Test

  IP nat inside source overload map route sheep interface Ethernet0

  access-list 120 allow ip 192.168.100.0 0.0.0.255 10.10.0.0 0.0.255.255

  access-list 130 refuse ip 192.168.100.0 0.0.0.255 10.10.0.0 0.0.255.255

  access-list 130 allow ip 192.168.100.0 0.0.0.255 any

  sheep allowed 10 route map

  corresponds to the IP 130

  He would go through the interface e0 to the Internet in clear text without going above the tunnel

  Jean Marc

• Access lists applied inbound VPN connections

  I try to configure access to homeland security lists, we have a multi site VPN services Terminal Server is the main traffic flowing on the VPN.

  102 of the ACL applies to cryptographic cards

  access-list 100 permit ip 10.1.5.0 255.255.255.0 10.1.6.0 255.255.255.0

  access-list 102 permit ip 10.1.5.0 255.255.255.0 10.1.6.0 255.255.255.0

  We need only allow traffic to domain connections and Terminal Server services only.

  I tried with no luck, remote clients lose the ability to auth against the domain controller.

  access-list 102 permit ip 10.1.5.20 host 10.1.6.0 255.255.255.0

  (DC also DNS and WINS)

  access-list 102 permit ip 10.1.5.21 host 10.1.6.0 255.255.255.0

  (DC secondary also DNS and WINS)

  access-list 102 permit ip 10.1.5.22 host 10.1.6.0 255.255.255.0

  (terminal server 1)

  access-list 102 permit ip 10.1.5.23 host 10.1.6.0 255.255.255.0

  (terminal server 2)

  access-list 102 permit ip 10.1.5.24 host 10.1.6.0 255.255.255.0

  (terminal server 3)

  If once they have connected to this topic, I've implemented these access lists it works very well, but once they log off and attempt to relog on, they are blocked. This leads me to believe there is more for field connections then meets the eye.

  Anyone have any suggestions for me? Everyone knows about this problem?

  Thanks in advance!

  Gregg

  Domain logon may require programming. It will probably be in the form of emissions e.g. directed 10.1.5.255. These emissions are going to spend your first list, but blocked by the second access list. To get around this, you can use assistance on the net 10.1.6.0 ip addresses. You can also add the following line to list 102:

  access-list 102 permit ip 10.1.5.255 host 10.1.6.0 255.255.255.0.

  Another thing to consider is to simplify your ACL 102. Small access lists provide better performance. In the given situation, the separate lines for 10.1.5.20 up to 10.1.5.23 IP addresses can be replaced by a oneliner: access-list 102 permit ip 10.1.5.20 255.255.255.252. Taking this one step further, you can even create a oneline for guests access list when you move the third server terminal server to the range of 16-19.

• Order a different number of prints for each image

  If there is a way to order prints of different images different number?

  Say I want to order a print of all my images in a collection of 4 x 6, simple enough.

  Then, I want to order some of them also in format 8 x 10, also quite simple.

  But what I can't find out how to order say;  3 copies of the #4 8 x 10 image, 2 copies of the #5 8 x 10 image and 10 copies of the image #14 in 8 x 10.

  Something I m missing?

  Any help is appreciated.

  Thanks in advance.

  • The options button lets you change the number of prints for each selected photo.
  • The 'add pictures and change print sizes' button allows you to add additional formats and you can even select different amounts for each size.

  See this help page: https://help.apple.com/photos/mac/1.0/?lang=en#/pht6e15ea68

  

• the analysis of a word table of ms with different numbers of columns for each row

  I'm reading in a MS Word table that contains 20 lines, each with a different number of columns.  I have to iterate over each line then I iterate on each column of the row and read his text.  I don't know a way to find out how to stop an iteration on the columns.  Is a property or a method which tells you the number of columns in a specific line for a table in MS Word?

  ID says:

  I'm reading in a MS Word table that contains 20 lines, each with a different number of columns.  I have to iterate over each line then I iterate on each column of the row and read his text.  I don't know a way to find out how to stop an iteration on the columns.  Is a property or a method which tells you the number of columns in a specific line for a table in MS Word?

  For each row, use the count property of cells. Since there a number of subject lines is the number of columns.

  Ben64

• Access denied for each file

  Dear all

  I hope you do well.

  Please let me know if you can help me with the following problem.

  I have a laptop with windows vista home premium, I only C & D drives, only a single user.
  in front of a low, I added new standard user called HARNOIS, no administrator and I edited the security option for the D drive, and I REFUSED all permissions for this user 'HARNOIS', which means HAMZEH may not access anything on the D drive.
  then after a day, I deleted account HARNOIS and then I tried to restore everything as before, but unfortunately my (Administrator) account, I encountered ERROR of ACCESS DENIED, I tried to take possession of each folder and then apply a full permission and subfolder and files in this folder, but the problem is the following:
  I need to change the option of advanced security for each file in this folder, nothing to apply at once, instead, I have to file-by-file and I have a large number of files in each folder.

  so, how can I restore my previous setting at a time.

  Thank you in advance.

  Best regards

  Faisal

  Hi FAisalFodeh, try this fix it tool to reset all security settings on this system http://support.microsoft.com/kb/313222 Steve Hebert - MVP Microsoft, Internet Explorer

• access list for traffic crossing and IPSEC

  Hi, just a question fast and easy if everything goes well as im on thinking that he. IM on the establishment of the IPSEC between a Cisco router to another Cisco router. I want to only allow RDP through IPSEC.

  I of course implement the ACL for the SHEEP, but I'll have to implement another ACL application outside? interface allowing a specific RDP server and denying everything.

  Thank you

  David

  I have extracted this router to work. I changed some details to conceal the source, but it should illustrate what you need to do.

  !
  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 2
  address of examplekey key crypto isakmp 2.3.4.5
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac AES256SHA
  tunnel mode
  !
  cust_map 10 ipsec-isakmp crypto map
  defined peer 2.3.4.5
  game of transformation-AES256SHA
  match the address crypto_acl
  !
  interface GigabitEthernet8
  cust_map card crypto
  !
  crypto_acl extended IP access list
  host ip 192.168.25.52 permit 172.24.0.0 0.0.7.255
  !

  HTH

  Rick

• Access control for Client VPN on Cisco 5520

  I use the ASDM to Setup client vpn for users. At some point in the wizard, you specify the traffic that is exempt from NAT that users can access. But there was no other controls on which ports/protocols to which they have access. My question is, where I would put the access rules? I would put them inside incoming interface (in the Security Policy tab) or y at - it somewhere in the tab (for example, the section of Group Policy) VPN I have let / restricts specific ports/protocols? I would just use trial and error but there are active P2P VPN on this box and the last time I added a new access rule for the inbound interface inside, he ended up breaking all P2P VPN access. Any suggestions?

  Thank you

  The f

  I'm sure you know, but that will affect all traffic, not just VPN, so don't forget to write your acl correctly, to allow what you want the vpn client subnet, deny the rest of the vpn client subnet, then let everything else. You must also make "no sysopt connection allowed-/ ipsec vpn" or traffic will deviate the acl. Good luck

  Oh, and don't forget your other vpn tunnels.

• Definition of different number of REB for each key

  Hello

  Assuming I have the following tables and sample data:

  create table test_tbl_aa
  (aa number(2));
  
  insert all into test_tbl_aa(aa) values(aa)
  select level aa
     from dual
     connect by level<=4;
     
  create table test_tbl_aa_n
  (aa number(2), n number(1));
  
  insert all into test_tbl_aa_n(aa, n)
    select aa, lv
      from test_tbl_aa
      cross join (select level lv
                  from dual
                  connect by level<= trunc(dbms_random.value(1,3))
                  ) v;
  

  For example, running the stmt insert in the table test_tbl_n the inserted rows are:

  AA    N
  --------
  1     1
  1     2
  2     1
  2     2
  3     1
  3     2
  4     1
  4     2
  

  In the example above defined result a stable set of records for each aa (for each series).

  Is it possible to generate different number or records in the table for each data value test_tbl_n

  column aa?

  For example for:

  AA    N
  --------
  1     1
  1     2
  2     1
  3     1
  4     1
  4     2
  

  Note: Oracle db 11g. v2

  Thank you very much

  SIM

  Do you mean like this?

  SQL > insert while test_tbl_aa_n (aa, n)
  2 Select aa, level
  test_tbl_aa 3
  4. connect by level<=>
  5 and aa = aa prior
  sys_guid() 6 and prior is not null
  7.

  6 rows created.

  SQL > select * from test_tbl_aa_n;
  AA N
  ---------- ----------
  1          1
  1          2
  2          1
  2          2
  3          1
  4          1

  6 selected lines.

• APPL_SERVER_ID is different in the CBD for each server file.

  I have 6 knots as forms + apache level, 2 nodes as level of CM and on a single DB node runs.
  
  I asked him just the value of view SERVER_ID FND_NODES. It shows 8 different SERVER_ID values for each server!
  Fortunately, it is the value of APPL_SERVER_ID in each of the dbc file present on the servers.
  
  My question is, is it normal to have different values of SERVER_ID for different servers...?
  NODE_NAME SERVER_ID
  --------------- ----------------------------------------------------------------
  SECURE AUTHENTICATION
  C201U337 9C2BBAF52F4008D0E044001A4B09E42E39060489262310725199227515699710
  C201U330 9C2BC5172DC00AA6E044001A4B09E42E32065429041790627836165020768437
  C201U331 9C2BD0D529000B7BE044001A4B09E42E24399550293612105522291335723235
  C201U332 9C2BDCD02D400CBBE044001A4B09E42E20708529451149697927290717515622
  C201U333 9C2BE804D4400EAEE044001A4B09E42E41410145443153698699760618303252
  C201U334 9C2BF2A0E4C00F71E044001A4B09E42E31646098872979120473974598540592
  C201U335 9C2BFC48D1401058E044001A4B09E42E22585142603175288108114713024518
  c201u338
  C201U336 9C2BA4028D00074FE044001A4B09E42E54326788279280415817440150025596
  
  
  This is because one of the developers complained that errors for JDeveloper - OAF saying PoolException: unable to create new database connection: FNDSECURITY_APPL_SERVER_ID...
  
  I donno what file dbc they will use. Please help me with this problem.
  
  Demand is 12.1.3 and database 11.2.0.2.0.
  
  Published by: Vicky on February 17, 2011 01:53

  I asked him just the value of view SERVER_ID FND_NODES. It shows 8 different SERVER_ID values for each server!
  Fortunately, it is the value of APPL_SERVER_ID in each of the dbc file present on the servers.

  This is an expected behavior.

  My question is, is it normal to have different values of SERVER_ID for different servers...?

  Yes.

  This is because one of the developers complained that errors for JDeveloper - OAF saying PoolException: unable to create new database connection: FNDSECURITY_APPL_SERVER_ID...

  I donno what file dbc they will use. Please help me with this problem.

  Web/Apache Server - Configuring JDeveloper for use with Oracle Applications 11i and R12 [330236.1 ID]

  Thank you
  Hussein

• A global Access List for possible VPN3005?

  Hello

  I want to what the VPN users and LAN-to-LAN-profiles are allowed to.

  for example. to block the RPC (tcp135) ports for all traffic from any profile

  Is this possible?

  Kind regards

  Chris

  You can create this filter in one place and then just apply it to each group of users and each configuration of tunnel L2L.

  Go to Config - Mgmt policy - traffic Mgmt - rules, add an inbound rule, drop, Protocol = TCP, Source and Dest everything (leave them as what), range from 135 to 135 TCP DEst ports.

  Go to config - Mgmt - traffic Mgmt - political filters, add a filter whose default action is to transfer, and then add the rule that you just created to this filter.

  Now, you can apply to all users by going under the Group and on the tab general and addition of th efilter in there. You can also go into the tunnel L2L config and add the filter to the tunnel directly.

  Note that you want to test this first, I didn't do all the tests and perhaps the source/dest or inbound/outbound in the wrong way or something like that.

• Access list for a single host 6248

  Hello

  I'm trying to setp an ACL on a powerconnect 6248 switch that allows traffic from certain hosts on a VIRTUAL LAN to another VIRTUAL local network.  I tried the setting up of an ACL to do this, but it does not work.  What would be the correct syntac for an ACL allow traffic to a certain vlan only to certain hosts?

  Please advise, ideas or recommendations would be greatly appreciated.

  Thank you

  Marlon

  
  

• I want different titles for each photo in a web gallery. The help file says:

  To display a different caption or title for each photo, click on the menu of settings customized to the right of title or a legend and choose Edit. In the model text editor that appears, insert the piece of metadata, IPTC title or caption, and click done.

  
  

  But what I do, the latest edition is for every picture the same.

  
  

  I have to select the image in a different way, I've already tried?
  

  Has chosen not to change, choose TITLE and LEGEND in the drop-down list.

  

  Then change the TITLE and CAPTION for each photo in the library/metadata Panel

  

  Then, each photo will be another caption/title

• Is widgets of composition - possible to have different sizes/heights for each container?

  Hi - I am currently a mobile version of our site of Muse and I wonder if it is possible to have different containers of sizes for each area of the trigger. I use the widget of the COMPOSITION of the TOOLTIP.

  Each container of the tooltip basically has an area of text in there with some information. The container of the tooltip is always the same size as the largest container in the composition of ToolTip widget.

  So, for example, I have a container of the ToolTip that has only a a text box with a few lines of text. A different ToolTip container has a text box with a few paragraphs.

  What I see is the length of the default container the size of a container with 2 paragraphs. Empty the container with the text box with a few lines of text has a vast space underneath, and I can't resize it to look any good.

  The only option is to fill the space with something like an image or another, which is less than satisfactory solution.

  
  

  See you soon,.

  Marty

  Yes you can, just go to the setting of the composition and change the position of straggling.

• Web Gallery - different caption for each photo - broken?

  It's something I've done successfully with versions before LR2.5 but for some reason that I cannot now create different captions for each photo.  The help page in line said: "to display a different caption or title for each photo, click on the menu of settings customized to the right of title or a legend and choose Edit. In the patterns of text editor that appears, insert the IPTC title or caption metadata element, and then click Done. »

  This does not happen.  If I create a title for the first photo, it appears for all others.  If I change the caption for the second picture, everything changes, including the first caption of the photo.  Is this a new bug, or am I just missing something?

  I can always change the HTML gallery, but it is not an elegant solution, to say the least.

  Help appreciated.

  DN

  Enter the title or caption in the library, in the metadata Panel. And select the items in the grid. The titles that you change apply to the web gallery, not the individual photos.