difficulty to remove the network wireless to my laptop

Similar Questions

• Do not see the networks wireless on my laptop under XP sp3.

  I have a laptop Toshiba Satellite 5 years old running Windows XP with SP3 and until the other day, he has been working very well.  Then the other day I started to clean my laptop to try to maintain it falls slower then it already is. (Glary Utilities, CCleaner, etc...)  Then all of a sudden I could no longer connect to my wireless network.  But if I plug it in wired Ethernet works fine but when I search for wireless networks to connect with, nothing appears on the pop-up window.  If I hit refresh, I get the same thing.  Here are a few things that I did to solve problems;

  1. made sure that the Radio will switch on the side of the laptop was on. (duh!)

  2. uninstalled the wireless network adapter in the Device Manager and allowed the operating system to reinstall it on reboot.

  3 both upgraded AND rolled back the Adapter.drivers wireless.

  4 power up the system Mode safe mode with network access and got the same thing.

  I have three other computers/laptops with wireless connection in the House and they all work very well.  And all of them show many wireless networks in the region.

  All ideas are welcome.  I'm all ears.  Thank you.

  Hello

  Perform the System Restore on the computer. Restore data when the wireless network was working fine.

  See also the follow-up article that will help you in troubleshooting wireless network connections.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

• Current file to use when it is disconnected from the network wireless/wired - shared network drive

  Hello

  We have a problem where we receive a "file in use" message when you are disconnected from the network. To reproduce the problem, what we do is:

  (1) connect to the wired network wireless disabled with

  (2) create a test document

  (3) to enter text and save on network share

  (4) remove the network cable

  (5) add additional text

  (6) reconnect the network cable

  (7) try to save the file to the network share

  At the beginning by clicking the X is the new message you want to save. Click Yes and the message arrives until the next time you hit the Hit of X no. and he loses the last change.

  From here we then go up to the network share, open the file and it comes up with "file in use. Open read-only. File is opened by us (Administrator account), and there is NO temporary file in the shared folder.

  Tried so far:

  -Run net config server/autodisconnect:-1 for trying to stop it disconnect the share

  -Checked pane, pane preview and off 'display the description of the pop-up window for folder and desktop items '.

  -Windows Update

  We try to reproduce on wired connection, because it is easier to reproduce that disconnects wireless. Seems to have an impact on several operating systems. Share folder is shared on a Windows 2008 R2 x 64 machine.

  Is this a known problem or is there something that we can configure to try to prevent the locking file after logging out? Ideally, we want the decline to go unnoticed and provide uninterrupted service to the user, unless they are trying to save during the fall.

  Thanks in advance for comments :)

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  original title: WiFi

  I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  I use a Huawei E585. I simply want to clamp it alll in the tray.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  (1) make sure that u run "NET START WZCSVC" on the command-line as soon as u Ouvrezunesession WINDOWS XP (START, RUN, NET START WZCSVC (command line)).

  (2) START, CONNECT, WIRELESS INTERNET CONNECTION

  --> under the 'GÉNÉRAL' tab: (1) right click on the wireless Internet connection; (2) click on properties; (3) make sure that all THE ELEMENTS under the title "THIS CONNECTION USES THE FOLLOWING ITEMS" are COMPLETELY FUNCTIONAL, i.e. UNCHECK THE ONES THAT DO ARE NOT ACTIVE ~!  (I recently turned off AVG and that this item has been inadvertently clicked on ~!) ;

  --> on the 'ADVANCED' tab: run the NETWORK CONFIGURATION WIZARD to reset your network

  3) http://support.microsoft.com/kb/871122 --> RUN 'DIFFICULTY CE PROBLEM' (ms - fix 50469)

• Computer connects to the network wireless as "local only".

  I am running Vista Home Premium SP2 on a HP Pavilion laptop.  I've never had any problems to connect this machine to a wireless network before, in hotels, at home, or anywhere.  My current home network is a modem - cable-> wireless-> wireless netgear n300 router.  My laptop connects to the internet via the modem cable directly or a wire from the netgear router.  I have a second, almost cell identical (it's intel, while the one who does not is AMD) which connects to the network wireless without any problem.  Two iphones connected wirelessely without any problem.  My HP laptop is the only one who refuses to connect to the internet.  Connected to the wireless network, it has access "local only".

  I tried the solution in this article: http://support.microsoft.com/kb/928233

  The question does not seem to receive an ip address, the computer receives an ip address.  I have disabled the IP v6, ran the norton removal tool, because I only had to a point and tried all other suggestions in these discussions: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/0949042d-074e-43ab-ba95-3c06cc2aa6be and http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/bc08f0e7-49a9-4458-9e0e-149b2df362ec.  I've uninstalled and reinstalled the adapter and all TCP/IP and network protocols associated with it.  I am at a loss and would welcome any ideas.

  Here is the result of the command ipconfig / all:

  Windows IP configuration

  Name of the host...: Arrakis

  Primary Dns suffix...:

  Node... type: broadcast

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1E-4C-B2-32-BC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.5 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Wednesday, 28 April 2010 21:40:55

  End of the lease...: Thursday, April 29, 2010 21:40:55

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: NVIDIA nForce Networking Controller

  Physical address.... : 00-1B-24-FA-DA-80

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 10:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {31C080CE-FE0B-4D50-B734-C782C9A25FBC}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {B198B0D3-B70A-4E3E-858D-9774C414EECD}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  If anyone has this problem, it has been resolved by rolling the security settings on the router WEP.  I got the answer from the support client netgear.

  Amazing how two iphones, another laptop with XP and a laptop running Ubuntu Linux all about them without any problem, but wouldn't connect Vista laptop.

• How to remove the network profile

  Original title: Double Internet access

  I have reproduced the internet access points. My network is one, it is not named or protected, and the other is called another network without any protection. Other users in households show only one when they go to access, but it's the bad access. They show only internet access. There are seven in our region, but only 3 see the same info and signal excellent. How can I remove the 2 bad ones?  Don't know what Internet number I use.

  Hello

  This problem can occur if the wireless network is available in your particular range or coverage area.

  Please see the following link on how to remove the network not searched profile:

  To remove a wireless network connection

  http://TechNet.Microsoft.com/en-us/library/gg252588 (v = ws.10) .aspx

  You can also check the suggestions provided in the following link:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/how-can-i-remove-old-network-connections/679baf9b-0303-4B2C-AF51-92981477a43a

  Important: the above article contains steps that tell you how to change the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, follow these steps from the following link: http://support.microsoft.com/kb/322756/en-us

  Please answer us on the State of the question to help you further.

• Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Hi Jer9009,

  Welcome to the Microsoft answers site.

  ·         Could you give the exact error code or error number you get?

  To connect multiple computers, install a network adapter in each and run a network CAT5 cabling to connect each one to a hub (and thus the other.) The computer that will serve as a transition will have a standard network card for wired and a wireless network adapter that will connect to the wireless (WAP) access point or gateway on the second network.

  A network bridge is software or hardware that connects two networks or more so that they can communicate. You can create only a single bridge network on a computer, but a bridge can handle any number of network connections.

  For more information, see the link: create a network bridge:http://windows.microsoft.com/en-US/windows-vista/Create-a-network-bridge

  Add a connection to a network bridge: http://windows.microsoft.com/en-us/windows-vista/Add-a-connection-to-a-network-bridge

  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I need to reconfigure the network wireless repeated now

  I need to reconfigure the network wireless repeated now.  Internet connection drops and I re - check the box 'use windows to configure wireless network. "  Why this keep happening?

  Provide more information, including the version and service pack of Windows, the brand and model of your computer and the make and model of your wireless adapter.

  In the meantime, however, your description sounds as if you have a utility provided by the manufacturer of your computer by the manufacturer of your wireless card which is competing with Windows for control of your adapter.  You must choose one or the other; You can't have both at the same time.  For a general introduction to the present, see http://www.ezlan.net/wzc.html

• My Windows XP home edition with service pack 3 now displays the status of my absorbing as "State of the network" wireless network connection but never connects to the network.

  My Windows XP home edition with service pack 3 now displays the status of my absorbing as "State of the network" wireless network connection but never connects to the network. This started after my last Microsoft update has been installed. .

  original title: status: network address acquisition
  Hi BKlap,
   
  Try these methods in the order.
   
  Method 1: Repair the network connection to solve the problem.
  For more information, see:
  To force a network adapter to acquire an IP address
   
  Note: The information in the article applies to Windows XP Home Edition as well.
   
  Method 2: Follow the steps listed in this article to resolve the problem:
  How to troubleshoot connectivity TCP/IP with Windows XP

• I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  Try this below and see if it help you.

  http://support.Microsoft.com/kb/871122

• I can't connect you on some client computers on a domain environment unless I have remove the network cable.

  I have almost five machines on my LAN that cannot log on to the domain, unless I have remove the network cable and then it connects.
  Please advise?

  On the domain controller or problems by communicating with the domain controller, when you remove the network cable, you connect with that caching of credentials.  Also look at the DNS settings on the RODC, the RODC DNS should point to itself, make sure that the machines are all on the same subnet.

  John

• HP Color LaserJet CP1525nw: Can't get CP1525nw connected to the network wireless Netgear Nighthawk x 6 R8000

  I have never been able to successfully get the printer installed by wi - fi with any stability, so we always connected via USB and shared. I bought a new router and would like to be able to print to this printer wireless anywhere on my network. I can't out of connected mode and mode wi - fi printer. Your software crashes, crash facilities to half way through. The printer indicates an IP 169.254.xxx.xxx, if the network is aware, but it's I can get. None of the HP tools will run under this operating system, they hang immediately upon launch. It's frustration none! Someone out there was a bit of luck with this printer!

  Dell XPS 8700 16 GB of RAM

  Earn 8.1 (64-bit)

  Comcast TG862G Gateway (POS)

  Router wireless Netgear Nighthawk x 6 R8000

  HP LaserJet CP1525nw color printer range

  Hi @jrmunn ,

  I want to help you get the printer works on the wireless network.

  There are a few different ways to install the printer on the wireless network.

  • Thanks to the support WPS.
  • Through the installation, by connecting the USB port, it will configure the wireless.
  • Once the USB installation is done. You can configure the wireless via an Ethernet connection.

  Cycle power to the router.

  First, we must restore the defaults on the printer.

  Press the OK button on the printer, go to the service, and then select restore default settings.

  Print a printer configuration page to make sure that the IP address and SSID are erased.

  Print a Configuration report.

  Uninstall the printer software.

  WPS configuration method:

  To connect your printer to your wireless router wireless using WPS:
  (your router must support WPS)

  Start the mode of the WPS button on your printer.
  Within 2 minutes, press the WPS button on your router.

  Then run a printer from devices and printers Add Wizard.

  The USB method:

  Perform a clean boot on the computer and disable the Antivirus software and any analysis in real-time in the Antivirus software also. How to perform a clean boot in Windows.

  Then run the installation immediately after connecting the USB cable, follow the steps described in this document to update the drivers so that's not new error. A fatal error during Installation of the software. Then the installation should continue. (you can use this procedure for any type of installation)

  If you are still having problems and you have an Ethernet cable, we can install the printer as a USB connection again and then configure the printer via wireless Ethernet.

  Method of Ethernet:

  Restore the default settings of the printer.

  Connect the printer to the router with an Ethernet cable.
  Wait about 1 minute and the printer must have a valid IP address.
  Print the configuration page to get the IP address of the printer.
  Type the IP address in the address bar of Internet Explorer which should open the printer's built-in web services page.
  Installing wireless over here now.
  Click the networking, wireless on the left, fill in information about the network and apply the settings.
  After the confirmation, then disconnect the Ethernet cable.
  Now you should have a flashing light on the printer in 1 minute wireless about.

  Print a printer configuration page, to get the new IPv4 address.

  Then create a new port with the new IPv4 address.

  In the devices window and printers, click right on the printer and on the left, click on printer properties, select the Ports tab.

  Click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.

• My Windows 7 computer will not find the networks wireless after a system restore.

  My Windows 7 computer is not find wireless networks after I did a system restore. It was perfectly good wifi before the system restore and other members of my family have a great connection except me is not a problem with my router. I think I know what the problem is, but I just don't know how to fix it. So there you go. I did my restore system about 2 days after that we moved on the provider of internet/tv "Comcast" to the tv/internet provider "Verizon". what I think has happened, is that I restored my computer to the point when we had no Verizon so that he could not find the network. Now, since we have Comcast it won't identify this network either, so maybe some of you out there could help me. : D

  Hello Nicolas,.

  Thank you our writing about Microsoft Community.

  If your computer has a wireless network card, Windows will automatically detect the networks wireless in range of your computer.

  You may encounter network or problems of Internet in Windows for several reasons.  Some common problems that can cause these problems are:

  • A wireless network adapter switch that is not enabled

  • WEP, WPA, or WPA2 key or password security issues

  • Cables that are not connected correctly

  • Corrupt or incompatible drivers

  • Missing updates

  • Network connection settings

  • Hardware or software problems

  I would ask you to check out the troubleshooting steps provided in the articles below and check if they help you solve the issue.

  Why can't I find a wireless network?

  Wireless and wired network problems

  Here are some links to site Web de Support of Comcast, who talk about troubleshooting of XFINITY Internet connectivity issues.

  XFINITY TV App: Can't detect your XFINITY home network

  The problems of XFINITY Internet connectivity

  Hope the helps of information provided. Do we know the State of the question, so that we can help you further.

  Thank you.

• I cann't get the network wireless hp 7500 to connect. I use wep-64 and shared.

  I cannt get the network wireless hp 7500 to connect. I use wep-64 and shared.

  I'm glad it's working for you now.

  Thank you to inform the community that has solved the problem.

• Remove the network adapter - error

  Hello

  I use the following code to remove all NICs connected to the specific virtual machine.

  Sometimes the workflow completes without error, but most of the time, I get the following error in the vCenter: invalid configuration for the device '1'.

  What can I change in my code?

  var nicsToRemove = [];

  for each {(device var in vm.config.hardware.device)

  If (device instanceof VcVirtualVmxnet

  || device instanceof VcVirtualVmxnet2

  || device instanceof VcVirtualVmxnet3

  || device instanceof VcVirtualE1000

  || device instanceof VcVirtualPCNet32

  || device instanceof VcVirtualEthernetCard) {}

  Here, you can add custom logic to decide whether to remove the network card

  This code example removes all network adapters

  nicsToRemove.push (device);

  }

  }

  var vmConfigSpec = new VcVirtualMachineConfigSpec();

  var deviceChanges = [];

  var deviceConfigSpec = new VcVirtualDeviceConfigSpec();

  System.log (VM. (Name)

  for each {(var nic in nicsToRemove)

  deviceConfigSpec.operation = VcVirtualDeviceConfigSpecOperation.remove;

  deviceConfigSpec.device = nic;

  System.log ("the nic is:" + nic.connectable.status);

  vmConfigSpec.deviceChange = deviceChanges;

  If (nic.connectable.status == 'ok') {}

  deviceChanges.push (deviceConfigSpec);

  }

  }

  try {}

  myTask = vm.reconfigVM_Task (vmConfigSpec);

  } catch (ex) {}

  System.Warn ("the reconfiguration of the VM error:" + ex);

  }

  It looks like your code is wrong here:

  for each {(var nic in nicsToRemove)

  deviceConfigSpec.operation = VcVirtualDeviceConfigSpecOperation.remove;

  deviceConfigSpec.device = nic;

  System.log ("the nic is:" + nic.connectable.status);

  vmConfigSpec.deviceChange = deviceChanges;

  If (nic.connectable.status == 'ok') {}

  deviceChanges.push (deviceConfigSpec);

  }

  }

  I think it should be:

  for each {(var nic in nicsToRemove)

  deviceConfigSpec.operation = VcVirtualDeviceConfigSpecOperation.remove;

  deviceConfigSpec.device = nic;

  System.log ("the nic is:" + nic.connectable.status);

  If (nic.connectable.status == 'ok') {}

  deviceChanges.push (deviceConfigSpec);

  }

  }

  vmConfigSpec.deviceChange = deviceChanges;

  You also probably want to get out the task if deviceChanges.length<= 0="" since="" there="" is="" no="" nic="" in="" the="" desired="">