Digital Purple squares

Similar Questions

• Analysis of the curves of the form

  Hello all, I'm very hard in adjust the data on the readings that I have a traction machine, the plot is attached and also text data. What I'm trying to do is to calculate the area under the curve at each position of displacement intervals (x-axis) ex from 2.3 mm to 15 mm. The first column in the text file will be moving (mm) and the second column is defined as the Force (N), the shape of the curve is uneven (jpeg file). I tried various tools such as integrated digital, least square adjustment, etc. but still do not have reliable results. Anyone here have an idea on how to perform the analysis, I am concerned of?

  Please give me advice!

  Suppose you have a set of X {1.5, 3, 4, 5.5, 7} data points.  They are unevenly spaced.  You get a value of X of beginning and end of your cursor over the graph.  The starting value is 2.5 and end value, 4.5 since the sliders.  You should now find it what index your points to start with.  2.5 is between 1.5 and 3 indices 0 and 1 in your table of X.  Similarly, 4.5 is between 4 and 5.5, indexes 2 and 3 in your table.  You need a function to determine the fractional value given a table index.  Our first point, 2.5, a index fractional 0.67 since it is two thirds of the way between index 0 and index 1 point.  Similarly, the endpoint is fractional index 2.67 since it is two thirds of the path between the indices 2 and 3.  Table 1 d threshold function gives you this fractional index.  Your full X array is the entry level.  The X value of your sliders corresponds to the threshold entry.  The output will be the fractional index.  To use it, you must convert any integer.  To do this, you must decide if you want to round the fractional index upwards, downwards or to the nearest whole number.  You can use the three primitives rounded in the digital palette to make one of these.  Once you have your clues, use the primitive subset of the range of tables table to get the parts of the matrices X and Y (two operations of subset) for integration.  Then use the integration routine that I mentioned above.

• X 200 maintenance

  So, I bought a replacement for my 200 X motherboard. I will introduce a new application of thermal paste (using the "chill WIND of THERMALRIGHT'' FACTOR from " ").

  Link to photo

  My question is, is it OK to apply the Paste on the entire inside the purple squares in my image, or all areas simply when it was red inside?

  If its okay to apply it in exposed areas purple together, for this actually benefit me? It will keep more fees?

  Note of the moderator; image (s) for a total of > 50 K converted for the programming of the Forum rules

  Good day and welcome to the community.

  Thermal compound is exclusively intended to be applied to the top of core chip die (the red area shown in your picture) and my experience only on the processor. The other "chips" under the Fan/Heatsink Assembly had regularly thermal pads for the contact. This was the case when I replaced the fan/radiator on my X200T. However, I've heard of some people using compounds there, but I don't know how well it fills the gap. Ideally, you want very thin, very even coverage on top of core chip die.

  Kind regards.

• I'm new to flash

  I'm new to flash and I need some help if you answer this can you write the details in the plain talk thanks (very senior)

  I have my ready photos from photoshop my screen flash photo has brought it up in the library, and then try to drag to the stage

  just as I get is a square not picture what the problem

  Help, please

  M0

  It is possible that you have the preview mode checked for the layer where you want to place the image.  In the image below, I circled the calendar control to toggle modes of all the layers big lines at a time.  You can also change layers by clicking this symbol in the desired layer.  In the image below 1 layer has its on outline mode, which is indicated by the green square.  Layer 2 is not on contour which is indicated by the solid purple square function.  The square shown on the stage is an image on the layer 1, as it appears with the mode on.

  

• Problems with the page numbering

  Hello there ' All!

  I received a few questions about the numbering of the pages:

  1. When the notes are present, they appear over my page numbers (in the lower left corner), which makes them invisible. How to avoid this?
  2. How can I ignore numbering for some pages, as the cover page, table of contents etc. ?
  3. How can I connect page numbers in my table of contents to my actual page numbers?
     

  Thank you!

  1A, ill-conceived layout? Page numbers should ideally be placed on your master pages, and outside of the margins, you book to plain text (i.e., top, side, or underneath the purple square). Move the frames of page number outside the place of purple Director. If there is no room for this, you need to adjust your margins!

  2. you can 'ignore' the page numbers (they will keep existing), but you can hide them in several different ways. Easier - and more dirty - trick is to put a white rectangle on them (don't do this!). You can also (Cmd) Ctrl + Shift + click on any element on a master page, so "free him" and then just delete the entire frame, with the page number and everything (I wish you didn't do this...). The best way is to assign a new master page to only those pages; a specially created for this purpose (if you have other elements that should appear on all pages), or simply the "[None]" blank page.

  3 search 'referrals' help if you use CS4. You can also search for "Table of contents", it may be useful to regenerate all the content, so the text is up-to-date as well.

• [beginner on Labview 8.5] Generation of a digital camera modulated square pulse triggered by an almost periodic pulse analog modulated square

  Hello

  I use a mx-acquisition of data (NI USB-6211) and I would like to use it to generate a pulse of digital modulation

  that is triggered by an analog input signal. The input signal is a pulse of squares analog modulated

  What is almost periodic. It's because of my set up, and I can't do anything with it. I would use the

  before the edge of this signal to trigger the production of a digital pulse signal modulated (0-5 V). My

  problem is summarized in the figure given in the annex. I would also like to have the possibility of

  Configure the 'backwardness' and the term of "TAU_LED", while the VI works.

  I have looked at several examples of instrument OR meter generation, generation of PCI I / AO, but doesn't

  not managed to solve my problem.  Does anyone have an idea of how start with my problem? Are there

  No matter what example VI that I could start to change?

  Thanks in advance,

  Gregory

  Hi Gregory,

  Sorry I forgot to mention: the Initial delay applies only to the first impulse of a redeclenchables generation.  Every subsequent impulse will use low time as the Initial delay.  I agree the behavior is not very intuitive (our latest guidance of series X actually supported an Initial period to allow on property Retrigger), but it is described in this knowledge baseand should also be mentioned in the DAQmx help.

  As you generate just a single pulse, I would recommend simply connecting the Initial delay and at the entrances of low time to the same value for each pulse will be delayed further.

  Exit tasks ongoing counter currently supports DAQmx writing.  However, the finished generations or simple impulse are not.  However, you should always be able to get the behavior you need with a property node DAQmx.  The current solution on the series E/M is:

  

  Again, this is not the most intuitive, but I checked that it works on my 6210.  After writing a new value in the software the pulse will be updated on the 2nd trigger.  Attached is the code stored in LV8.2.

  Best regards

• How to read the digital square wave pulses

  Hello

  I recently bought a blue-white meter. I have successfully read the digital square wave from the sensor. However, I face a problem to calculate the flow rate and the total volume of liquid. Can someone help me with this?

  Technical data of the flowmeter can be access to the http://www.blue-white.com/Products/ElectronicFlow/MicroFlo/80000-406_microflo.pdf. And the calculation can be found on page 9. I use NI9401.

  Thank you

  
  

• Digital square wave

  Hi all

  I want to check if my digital square wave turns on or off. If someone has an idea, please help me

  I created a mask, so that if my signal leave the mask. I have an Error Message. "It's job but every time I should change the values of the function Culsters ' specification limit" if I change the Signal

  You will find in the attachment the block diagram.

  Thanks in advance for your answers

  Best regards

  How are you brightness measure?  A digital signal is enabled or disabled.

  Duty cycle that you can measure quite simply.  There is a VI called Pulse Measurements.vi who will do it for you.

• Square on the map digital wave

  I want to have a simple square wave (duty cycle 50% - didn't need to change) at the exit on a digital map of labview IO.

  My problem: 9472 and a 9403 are the cards I have. When I start my VI of squares (attached), I just can't get enough high frequency. For example, map of 9472 is accurate up to 25 hertz. I checked on an oscilliscope and once I turn the last frequency 25 Hz on VI, the card seems out max and it won't display anything faster than 25 Hz. In addition, for the 9403 the same thing, except that the 9403 card seems to have a frequency limit of 11Hz about. Once, 1-11Hz, the map is very accurate of what is on my VI, but when I turn the VI above 11Hz, the map seems maxed out and just stay at 11Hz.

  I'm looking to get up to 500-600 Hz range.

  What is causing my cards be limited to these frequencies? How can I increase the frequenies that they went out to about 500-600 Hz?

  Thank you!

  The 9472 is a module of software timing. You will never get 500-6000 Hz out of it. When used in an NI CompactDAQ chassis, the NI 9403 module can serve only static type (timed by the software), so it has the same problem.

• When you use Excel or my Peachtree Accounting program, entered digital as "$152(32 in the accounting package or the same number with a square symbol as the decimal point in Excel.)". No idea what I should check first?

  When you use Excel or my Peachtree Accounting program, entered digital as "$152(32 in the accounting package or the same number with a square symbol as the decimal point in Excel.)".  No idea what I should check first?

  Thank you for visiting the website of Microsoft Windows Vista Community. The question you have posted is related to Office Excel and would be better suited to the office community. Please visit the link below to find a community that will support what ask you

  http://www.Microsoft.com/Office/Community/en-us/default.mspx?d=1

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Blue square icon with 2 White arrows attached to the photos transferred from the digital camera

  All uploaded photos from digital camera to the windows7 picture library have a blue square icon with 2 White arrows ">" attached to each picture in the lower left corner. How do I overcome this?

  All uploaded photos from digital camera to the windows7 picture library have a blue square icon with 2 White arrows ">" attached to each picture in the lower left corner. How do I overcome this?

  =========================================
  If you are running Norton 360... the following article is maybe worth a visit:

  Green checkmark or icon collection blue arrows displayed files in Windows
  Explorer:
  http://www.Winhelponline.com/blog/green-tick-or-blue-arrows-icon-overlay-displayed-for-files-in-Windows-Explorer/

  If you do not need the backup indicators feature you can turn off by
  by clicking settings in the main window of Norton 360, disable the backup
  Status indicators check box and click Close.
  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• How to generate a square wave of continuous digital output using USB 6343?

  I need to generate a square of 600 kHz from my 6343 wave.  The specifications indicate I could use PINS P2.0, but I get an error saying that it is not supported.

  Thanks in advance for your help.

  Jodi

  Dan,

  Thank you very much.  Counter method worked very well.

  Jodi

• How the little purple pink squares onto a PDF to add/change the text. Also how edit you fonts? This app is not easy to use. Read the instructions and they are lacking to say the least.

  I hate this app! I read the user guide, but it does not with the application. How/where are the small Pink/Purple to add/change the text boxes? How can we change phont and point?

  If you use Adobe Reader/Acrobat Reader, that you do not sense because it's none of those things.

  Edit a PDF file and the creation of form fields are made with Acrobat Standard or Acrobat Pro.

  Once the fields of the form are added, people with Adobe Reader can fill.

  Note that, even in Acrobat Pro, editing is very limited and frustrating because PDF is not made for editing.

• Flickering squares colored forming strips on the screen

  I have an iMac 27 mid-2010 "with a videocard ATI Radeon HD 5750 El Capitan running.  I have recently begun to see small squares colored screen (pink, orange, red, green mainly) that start as low spread across the screen and little by little become denser with time.  Places at their peak form a checkerboard pattern forming bands across the screen, but generally not in the active window.  Sometimes, I have a few strips of squares flickering and some fixed.  The individual squares are really small - only a few (2-3) mm in size.  I also occasionally get a purple line or two parallel lines of purple on the top of the screen (but not in the active window).  The points seem to appear when the internal hard disk is done a lot of read/write (but I couldn't be sure that it is a part of the problem). I have attached a screenshot that shows a few random points - he gets much worse than this.  Maximize the active window frequently, but not always, makes them disappear.  If they appear in the active window (which happens rarely), the computer stops responding.  I also seem to be getting some flickering when scrolling windows or opening menus, or an area of the screen not refreshing immediately, which I've not seen before.  The computer in all other respects seems to operate normally.

  The purple strips at the top of the screen do not appear in this screenshot, but points are hard to see.

  

  First of all, the problem occurred after the upgrade to El Capitan.  I made a second installation of El Capitan in case it was caused by the upgrade nothing helps.  It is currently running 10.11.2.  The computer also had a replacement of that HARD drive internal installed a few months ago, but the points started to appear some time after that has been done.

  Someone has encountered this, or know a solution?  I'm starting to think that the trip of the new year for the doctor to Mac may be needed.

  Thank you

  I'm starting to think that the trip of the new year for the doctor to Mac may be needed.

  Yes. Looks like it's maybe a faulty graphics card.

• Cannot fax Officejet Pro 8500 A909g; was recently sold by Verizon to switch to FIOS digital telephony

  Hello

  Recently switched to FIOS digital voice service. I have a HP Officejet Pro 8500 A909g. Y at - it a patch or other difficulty that I can use to send a fax? Receives errors in communication since going digital.

  Thank you

  Michael

  Fax is STILL an analog service, he may be able to work for DSL or VOIP, but it is never a guarantee. Unfortunately, there are no fixes, updated or newer models that will change this.

  You can try to contact Verizon to see if they have filters or suggestions, but it can never work with a digital line.

  I know it's frustrating, but there is not much that can be done. You can watch are E-fax to the square or a secondary analog line.