Digital waveforms I2C library sync settings

Does anyone know how the consolidation of the 'I2C Timing (ns)' is in the following code?  This is an abridged version of the example of the VI "HSDIO I2C - hardware Compare.vi ' downloaded from here.  It uses the I2C Digital Waveform reference Libarary.

Time on the x axis doesn't seem to be any help, and the front panel settings are very cryptic in their naming system.  No one knows what these numbers mean and how it correlates to real time (dt) between each point?

I finally found where the parameters are specified.  They can be found in the specification UM10204 I2C - bus and manual.

Under the current revision 5, found in table 10 on page 48:

Tags: NI Software

Similar Questions

  • Reference library of digital waveforms of SPI for LV 7.1

    Hello

    I'm using LabVIEW 7.1. I want to implement SPI communications on a NI HSDIO (PCI-6541) device.
    The SPI Digital Waveform Reference Library (http://zone.ni.com/devzone/cda/epd/p/id/6163) is available for LabVIEW 7.1? Someone at - it successfully he converted from 8.2 to 7.1?
    The screws are also available under the reference Application Communication Protocol series for digital devices of waveform page (http://zone.ni.com/devzone/cda/epd/p/id/6200) available for LabVIEW 7.1?

    Any help would be appreciated. Thank you.

    Hello

    Unfortunately there is no simple way to convert libraries back to the 7.1.

    My suggestion would be to download an evaluation copy of LabVIEW 8.6

    You could use the trial period to open libraries and use as reference to re-create what you need to in 7.1.

    Hope this helps,

    John

  • Extract a channel of a digital waveform

    I use the I2C Digital Waveform reference Libarary to create a WDT which consists of two lines/channels.  I was wondering how I could extract/remove a channel, the wave form and how can I add/merge signals tracks in a single WDT?  I looked around for the screws, but nothing seems to work with the WDT.

    Right now my WDT is like this:

    How can I get these two lines in separate WDTs?  And then how would I be able to merge them again?  Naturally, I don't want to just remove them and merge them, but that would be an example of good practice to demonstrate.

    After much trial and frustration, I found a way to do what I was looking for.  It is not the most elegant, but it works!

    That's how I extracted the two strings in an array and then merge to recreate the original graph:

    * Note: The reason why there are 2 in the waveform data table is because my waveform contains 0 and Z instead of 0 and 1.  The three States Z corresponds to the 2 digital.

    I even took it a little further and extract a single line.  This could be changed to extract any line and eventually merge your own custom signals:

  • Firefox update kills sync settings?

    Today, firefox suggested "Refresh" for the first time ever. That went well, but it seems to have killed my sync settings. Sync now asks me to create a new account. Is - is this expected? I have not found clues for that behaviors in the documentation of refreshment.

    "Refresh" removes everything, like a "factory reset".

    However, your synchronized data is still on the server, on the "create new account" screen, there should be a link to 'sign' in to the existing account.

  • The use of generate for demodulation and modulation PSK sync settings

    Hi I'm trying to generate Parameters.vi of sync allows you to synchronize the flows recovered after demodulation and my input to the block of modualtion streams but I do not know how to work with this block to synchronize the input with the output stream stream. Also would you please let me know what are the modes of synchronization of the input bits and demodulation bit stream. I really appreciate your help

    Thank you

    Hi en99,

    To use 'Synchronization generate MT Parameters.vi' you must wire in what follows on your block diagram:

    • The parameters of the system created in 'System generate MT Parameters.vi' needs must be connected directly to the vi synchronization.

    • Sync settings must be wired directly to 'MT Demodulate.vi'

    • The bits of synchronization can be connected to synchronization vi directly at "MT generate Bits.vi.

    What I did is took your 11. VI you downloaded in your post previous and amended to contain synchronization vi. I recorded as a 2010 version.

    I hope this information helps!

    Kind regards

  • Continuous output of digital waveforms on PCI-6602

    I use 6602 PCI to get a continuous 1 MHz square wave output of DIO1 ~ 32 sequentially controlled by LabVIEW. I Ctr0 to generate a clock 2 MHz and used Ctr0InternalOutput as a source of sample for DIO1 clock ~ 32. I have attached the code and the texture as follows.

    The code works fine on PCIe-6251 and digital waveforms of 1 MHz is very stable.

    But when I run on PCI-6602 I got an error-200077 (you asked for: sample clock; you can request: on-demand).

    6602 PCI does support material timing? I found no information about this its specifications. If she can't, how can I avoid this problem and get what I want? Thank you!

    Yi

    Version: LabVIEW 8.2

    hardware: PCI-6602

    Hello

    Have you looked at the specification for the 6602?

    http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/1123

    Click on "specifications".  Scroll down to "digital i/o".  Watch "Timing".  It clearly says "software".

    The DIO lines on this Board are not timed by the hardware.  They are clocked by the software.  The data sheet that explains very clearly.  That's why you see the error clock sample - that the Council can't stand DIO clocked by the hardware.

    The 6251 supports clocked by DIO material, so why your code works very well with this Council.  You can do the generation of signals with a 6602.

    Hope says.

    d

  • How I ouptut a digital waveform, it has collated and compare it to the original with a usb-6211 box?

    I want a digital waveform to a circuit of output, read the return signal and compare the original to the read signal. I use a usb-6211 housing is it possible and if so, how?

    Use a comparator "equals sign", mark the post as a solution if you have the makings of what you wanted.

  • Generate a digital waveform like memory on PXI cards

    Hello

    I'm looking for a way to send a large digital waveforms using a PXI digital signal generator. I saw DIO HS cards, but their memory is smaller than the files that I want to transfer. My understanding is that the PXI backplane bandwidth 132 MB/s. So, I shouldn't be able to stream a digital signal from the memory of the card that is slower than the CPU? For example, 50 Mbits / second (equivalent to only 6.25 MB/s)? However, I think I understand after reading their textbooks is that you cannot continuously transmitting a large waveform of the processor memory file, you must transfer the file to the memory of Council first and then transfer that out.

    Does anyone know if there is a way to have a flow of digital signal generation card an arbitrarily large directly from memory to the processor of digital signals? Or, what is the fastest card of pxi digital signal generation that does not require the storage of Council first files?

    Thank you

    Isaac

    Hello Isaac,.

    Take a look at the following area developer.

    NOR-HSDIO Stream from disk (generation) using Win32 file IO

    Note that you will not be able to take full advantage of the maximum rate of update HSDIO devices, because the data must be transferred in a bus.  Some other considerations are the width of the data as well as the HSDIO device you select, which may depend on other requirements not related to the size of file or waveform (for example the standard voltage or whether you need hardware compare).  For more information, take a look at the developer following items area.

    Data streaming of Architectures in the PXI systems
    The use of National Instruments Logic Analyzer and generator of test patterns Solution

    Advanced features of e/s high-speed digital devices White Paper Series

  • Can someone tell me how to extract a part of a digital waveform?

    I am trying to extract a part of 2 analog waves (using the http://zone.ni.com/devzone/cda/epd/p/id/4149 for example) analog signals is synchronized with a digital waveform.  I need to extract the same portion of a digital waveform.  Can someone tell me how to add the digital extractor in the example above?

    Hello

    Here's your extractor example slightly modified in order to add the digital data extraction.

    The principle is exactly the same, the tricky part is how to get digital data which is different from analog data.

    You can also add nodes property to identify the value read on the analog graph sliders on the digital chart.

    Kind regards

  • Is it possible to scroll on the y-axis of a graph of digital waveforms?

    Hello!

    I use LV 8.5.1 and I want to draw 64 signals on a graph of digital waveforms.

    But if the graphic is too small, I see not all signals, and if I enable auscale on the Y axis, so the signals are not recognizable.

    Is it possible to activate the scrollbars on the y-axis?

    Thank you.

    Hello!

    Try to use the nodes property Y scale with a slider horizontal/digital control. As:

    Find it here:

    I hope this helps!

  • How to record a digital waveform with timestamps for each sample?

    I am generating a digital stimulus and capture the digital answer using 6552 HSDIO. The captured response is data digital or forms of digital airwaves.

    I want to save the captured digital answer and save it in a file in spreadsheet showing the timestamp for each sample. How can I go to a digital waveform to a worksheet that contains all samples and timestamps for each sample?

    Comvert digital to analog is just the wrong function. And when you converted to U8, you just threw the calendar information. Try the code below. He puts the time in a single column. If you want to only two columns, its an easy mod.

  • Table 1 d of digital waveforms

    I have a table 1 d of digital waveforms and I need to work with the data. I can't get the 'mass' to work with any function table or any other type of function also.

    I need to be able to convert these so I can find a particular value in the table.

    Thank you.

    So you're just trying to get inside the matrix? Use a loop For or an Index Array node.

  • Count the number of 1 is present in digital waveforms obtained by converting the pulse signals.

    Hello

    I use Analogtodigital.Vi to convert the pulse of the sequences in digital.signals.I am able to get the representation of digital waveforms of impulses.

    But how to count the number of 1 is present in the converted digital waveform. I want to count the number of 1 is present in the digital waveform converted.

    Thanks in advance.

    Have you tried the block scheme of similar to the Digital.vi of opening?

    It creates an array 2D uncompressed 1 and 0, which is the binary 16 bits A/D conversion of each element in the array Y of the input waveform. You can use the DWDT digital Array.vi Boolean to convert a 2D Boolean table. Then convert Boolean values to 1.0 and summarize the array of integers. The sum must be the number of 1 bits in the digital waveforms.

    Lynn

    Note: The VI attached is saved in version 8.6. When I have it saved for the previous Version a warning was generated about the possible differences in the versions. Let me know if it doesn't work, and you are using which version of LV.

  • static/digital waveform output and low frequency measurement of voltage - SMU-6358

    Hello

    1. I have an attached VI [digital_voltage_output] who must generate a logical true or false static state in the output of the device/port0/line1 Word to say. When the VI works I click the button several times, but nothing happens to the port0/lines1.

    2 such a thing [digital_voltage_waveform_output_square] if I'm trying to generate a digital waveform to pin the same with the waveform generating VI. If I connect a waveform chart to the output of the generator function VI, then the chart will show me the good waveform I want, but still nothing is written to the text file.

    3. I have read the manual for the X series cards, but it remains unclear for me a little how to things of the road in LV I have a measure of the frequency measurement VI low frequency that I downloaded. It offers me the ports for the supply frequency - ctr0, 1, 2, etc. As far as I'm concerned the PFI ports are responsible for these types of actions. How can I find out the LV that I want to connect say ctr0 and pfi0? »

    I use LV 8.6.

    Thank you

    Kriváň

    Hi Kriváň,

    The problem you had with the choice of a specific digital line as a physical channel, is that the control that was previously used in this example was created for a data acquisition task that uses a whole port rather than a specific line. I was able to overcome this problem by removing the control and recreate. The control now gives you the option to choose the specific digital lines e.g. port0/PXI1Slot2/$line0.

    I was also able to overcome the error of-200802 you mentioned. I was able to do this in a real constant of wiring at the entrance to auto-start the VI DAQmx writing then remove the DAQmx beginning the subsequent code VI. The modified code is attached.

    I hope this helps.

    Best regards

    Christian Hartshorne

    NIUK

  • Could someone tell me how to convert the digital signals in table 1 d of digital waveforms

    I use 9474 for drving an engine. for that I have uses 2 ports - to activate and another for running. These signals in the form of Boolean values.  I am to convert these signals to a table and since iam doing a digital waveform. but when iam connecting these to the module 9474, it show an error "source is a digital waveform and sink is 1-d array of digital waveform... any body can help in these issueee please...»

    Pop - up on the thread and choose Insert...

    Build the table.

    Ben

Maybe you are looking for