direct access to the modem point

Similar Questions

• blocking direct access to the oracle server

  Dear Sir

  One of our condition of pci - dss to stop direct access to the db. One solution I know:

  TCP.validnode_checking = YES

  TCP.invited_nodes = (192.168.1.91, visionhost.solutionbeacon.com)

  But this option will allow the IP address of the node invited with sqlplus using tns names also. Have any have experience to solve the problem of ending up with pci - dss?

  In which paragraph of the PCI - DSS doc that makes you think that there is a problem? I work with version 3.0 (November 2013) and I can't find anything like that. For example, paragraph 8.7 c, "review of database access control settings and application of database to verify configuration settings that the user access directly to the or queries of databases are limited to database administrators" does not say that the DBA is not able to connect to the application server. And all the stuff of firewall in requirement 1 close the access to the network and between networks, not within the network.

  Are you sure that you have a problem? There is no interest to 'fix' something that doesn't have a reference in the doc.

• ESXi 5.5 - Direct access to the local logical unit number

  I have a 5.5 stand-alone ESXi server.

  It has 2 local SAS controllers

  Controller 1 (HP Smart Array P410): data bank single RAID 10 with two VM's local logic unit number

  Controller 2 (HP Smart Array P812): only RAID 6 LUNS nothing on it yet...

  My question is that I need one of the virtual machine to access that LUN. Is it possible to give direct access to the VM to the controller and/or the unit number logic rather than create a vmdk and massive data store?

  If it is I know Flash would not work on these data, but that really doesn't matter in this case.

  Thank you

  Kenny

  Hi Kenny, and welcome to the communities,

  There is an article dealing with your situation KB: http://kb.vmware.com/kb/1017530

  Concerning

  Tim

• vSwitch ESXi 5.1 workaround to virtual machines (direct access to the network)

  Hello world!

  I have a server running properly the 5.1 ESXi hypervisor and got inside the physical grid active router with DHCP. How can I configure the vSwitch on ESXi 5.1 work not managed on the network, without VLAN and have direct access to the network?

  Just to clarify, I would like to first of all virtual machines VMware Workstation works - if it is possible to run several virtual machines and define all NICS (Network Interface Card) as connected by a bridge, that is to say. Each VM gets the specific configurations of IP to the external router.

  Since now, thank you very much for the help!

  Best regards

  Eduardo

  With ESXi the vSwitches work comparable to Bridged networking, so there is really nothing special to do.

  André

• Direct access to the form fields in the process?

  HI -.
  
  I am building an Apex application that has a section of form, I need to generate manually - I need a lot of Javascript custom treatment within this block of fields (generating an arbitrary number of fields based on other user input, update totals the user to change values, etc.). I have no problem to build that portion of the application.
  
  However, I am now not sure how to access the fields I create in a post submit processes (so I can process/save the data entered). Y at - it has a syntax that I use in the process through a list/collection of all submitted fields, or (b) directly access the value of the field named "xyz"?
  
  Thank you

  If you mean spit your own tags to entry with htp.p, you can do that in the APEX. You must use the APEX_ITEM package. When you submit the form, you will get an error because the procedure of wwv_flow.accept is not the settings that correspond to the fields in your form.

  Tyler Muth
  http://tylermuth.WordPress.com
  [Oracle security application: development of secure database and Middleware environments | http://sn.im/aos.book]

• RV016 access to the modem in wan1 administration page, wan 2... from LAN

  Hello

  We have installed router rv016, balancing 5 adsl conections.

  We can access the router rv016 with IP 192.168.1.1 LAN.

  We can access the administration modem1 page in wan1 which has IP 10.0.0.1

  But we cannot access other pages of Directors of modems as fitted wan2 IP 10.0.0.2, or modem wan3 with IP 10.0.0.3, modem wan4 or wan5...

  In the diagnosis of rv016 page, we can make a successful ping 10.0.0.1, but not to another wan...

  All modems have active DHCP ok with access authorization.

  Can you help us?

  Thank you!

  Hello

  Change modems to get LAN IP addresses in different subnets:

  10.0.0.1

  10.0.1.1

  10.0.2.1

  10.0.3.1

  10.0.4.1

  Then, everything should work perfectly.

  Please mark this thread as answer or reply if you have any additional questions.

  -Marty

• direct selection - move the anchor points with the arrow keys of the keyboard

  Hello

  I use Illustrator CC.  I just use the image tracking tool to create a version vector of my company logo.  It worked pretty well, but now I'm just trying to clean it up a bit.  I have a few anchor points that I want to just push upwards or downwards into the smallest possible increment.

  I think it would be easier for me to do using the arrow keys on the keyboard instead of the mouse, but the arrows cause my selected anchor point to jump in too large a distance way.  I checked to make sure that the bearings commented, snap to grid and snap to Point are all extinct.  I don't see anything else to do.

  Can someone tell me which control how the keyboard arrow keys will move an anchor point, and how can I fix this to the smallest possible distance?

  Thanks in advance,
  Paul

  General Prefs, area keyboard Increments. Have something you need.

  Then use Nudge (up, down, left, right arrow).

• stripped/direct access to the functionality of toplevel menu in panelcollection

  Hello
  I use a panelcollection with the table of child components. The facet "edge" displays the menu "columns" with the box to reorganize/show/hide feature columns in the table.
  I want to call this feature on a context/popup menu in the table.
  
  I use this code in the panelcollection, which works very well, but must be replaced with a popup.
  

   <af:panelCollection id="dc_pc1" binding="#{component.dc_pc1}">
      <f:facet name="viewMenu">               
          <af:group id="dc_g1">                 
                  <af:menu text="Queries" id="m_qs">
                   <af:group id="dc_g4">
                       <af:commandMenuItem
                         id="cm_qs_0"
                         text="Default Search Option"
                         binding="#{component.cm_qs_0}"
                         shortDesc="This schould be the default configured Query"
                         type="default"
                         disabled="true"
                         icon="/custcc/images/icouserdefaultconfig_16_1.png"
                         actionListener="#{component.changeSearchMenueAction}"/>
                   </af:group>
                  </af:menu>                
                  </af:group>
                </f:facet>
        <f:facet name="menus"/>
        <f:facet name="toolbar"/>        
        <af:facetRef facetName="tablecustomizable"/>
      </af:panelCollection>
    </af:componentDef>

  How can I directly call dialog boxes of column ("showColsDlg") of the facet edge of panelcollection?
  
  Thanks in advance!

  Hello

  You can not. The bean component is RichPanelCollection and exposes the setter/getter but no functionality. Eventually, you could use JavaScript to simulate a click

  Frank

• Problem of access of the Station point.

  I turn on my laptop hotspot position so I can connect to wifi on my ipod touch and my ipod connects very well and my laptop says it's connected as well but my ipod gets no internet.

  Ajit,

  It is my understanding that HotSpot Station is only on the image of the plant and not available for download. Using the system restore with the original image, is the only way to get the HotSpot Station on the system.

  Since Windows may offer ways to share your wireless connection, try to read...

  Set up a shared Internet connection using ICS (Internet Connection Sharing) and using ICS (Internet Connection Sharing)

  Rick

• Direct access the 4 G/LTE Verizon's internet connectivity-related issues

  During an attempt to access remotely via a Direct access to a tablet with 4 G/LTE from Verizon, we are unable to access the internet. Before the installation of a Direct access on the Tablet, 4 G high-speed worked fine, but once the Tablet has been recreated for a Direct access, we no longer had access to the internet. A call to Verizon revealed that the Tablet has been connected to the system of Verizon, but is was not connected to IPv4 or IPv6, and whether Verizon could not move forward. Are there Direct access settings that should be addressed in order to allow access to broadband (4 G SIM chip)? Thank you.

  Hello

  I understand that you are unable to access the internet during an attempt to access remotely via direct access on your tablet.

  To better understand the issue, please send us the following information:

  1. What is the brand and model of the Tablet you are facing problems with?
  2. The problem occurs on other laptop or Tablet?
  3. You are connected to the domain network?

  If you are connected to the domain network, you can post your request in the forums TechNet from the link below:

  https://social.technet.Microsoft.com/forums/en-us/home

  It may be useful, get back to us with the required information and we will be happy to help you.

  Thank you.

• Directly access the disk in the guest OS windows 2003?

  Hello!

  Deployed ESXi 3.5 for the first time today to learn more about Virtualization and save some of my servers.

  But I ran into a few problems, I have 3 x 1 TB disks with partitions encrypted TrueCrypt, I need to give direct access from the guest OS to Windows 2003.

  Isn't this possible?

  I've been running VMware Workstation earlier and there you can do it easily, but I can't find any way to do this in Esxi: S?

  Thanks in advance!

  Basic System Administration http://www.vmware.com/pdf/vi3_35/esx_3/r35u2/vi3_35_25_u2_admin_guide.pdf

  page 153

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• [WAG200G] problem to connect to the modem cable Alloys Atlanta Dcp2203

  Hi all!

  I recently got my new cable internet access (I used to have DSL) and I want to use my WAG200G to distribute internet by air.

  When I connect my laptop to the Dcp2203 of Atlanta Alloys via ethernet, I get an external IP (200.XXX.XXX.XXX). I need to adjust my ethernet interface get ip dynamically to achieve this.

  Now I need to connect Dcp2203-(ethernet)---> WAG200G - wifi---> portable

  How can I configure my WAG200G to work using this structure?

  Thanks to you all!

  You can't really use your WAG here. You will need a router ethernet, not a DSL router.

  The only thing you can do is use the WAG as access point and connect the laptop directly to the internet. This works as long as you don't want to connect a device to the internet at any time. You will not be able to connect 2 or more at the same time, because your ISP only allows you to have an active connection at any time.

  To set this up, you will need to connect a computer to the WAG. Open the web interface of the WAG to http://192.168.1.1/ to first set up your wireless network (SSID, enable WPA2 Personal Security with AES encryption and a password strong change). Disable the DHCP server on the main settings page.

  Then one of the ethernet wire ports of the WAG in your modem cable. Now you can connect wireless to the WAG and the WAG access to the internet and the modem. New: your computer will have direct access to the internet and will have a public IP address. You can't have two active connections at the same time.

  If you need to make changes on the WAG, you set a static IP address on your computer, for example 192.168.1.2 with subnet mask 255.255.255.0. Then you can access the web at http://192.168.1.1/ interface when you have completed your changes, go back to the DHCP/Auto IP on your computer.

  Otherwise, you should get a router, for example Wireless Linksys WRT routers.

• Access the views Where the access to the underlying data, through a role

  I have a user (say User1) who granted select access to motherlode via a role table

  User1 has a bunch of useful views created I want User2 to have access to the. User2 should have access only to these points of view, not to the underlying table.

  User1 can grant access to his point of view because it has no direct access granted to motherlode tables.

  I managed, based on a technique that I have for the most part, but do not entirely understand, give User2 access to data through a function. The solution is below.

  My general question is: y at - it an easier way (other than the grant direct access to the motherlode User1 tables)?

  My question is: the definition is possible shorter somehow. I know I can automate the production of the code for some of the statements using metadata, but, for example, is it possible to base the declaration of type (t_p5) on the existing view? (I have about 15 views I need to provide access)

  Solution is, where v_p5 is the original view:

  User 1:

  CREATE or replace type t_p5 as an object

  (< columns and data types of v_p5 >

  )  ;

  CREATE or REPLACE TYPE t_p5_tab AS TABLE OF THE t_p5;

  FUNCTION to CREATE or REPLACE f_provide_p5 RETURN t_p5_tab

  PIPELINED IS

  l_cur SYS_REFCURSOR;

  l_rec v_p5% rowtype;

  BEGIN

  L_cur OPEN FOR ' SELECT * FROM v_p5';

  LOOP

  EXTRACTION l_cur

  IN l_rec;

  EXIT WHEN l_cur % NOTFOUND;

  GUIDELINE (t_p5 (area = > l_rec.region))

  , district_name = > l_rec.district_name

  , current_month = > l_rec.current_month

  , p_current = > l_rec.p_current

  , previous_month = > l_rec.previous_month

  , p_prev = > l_rec.p_prev

  , diffp = > l_rec.diffp

  , diff_perc = > l_rec.diff_perc

  , previous_year = > l_rec.previous_year

  , p_year = > l_rec.p_year

  , diffy = > l_rec.diffy

  , perc_diffy = > l_rec.perc_diffy

  ));

  END LOOP;

  RETURN;

  EXCEPTION

  WHILE OTHERS THEN

  raise_application_error (-20000, SQLERRM |) Chr (10) | l_sql);

  END;

  And user2:

  VIEW to CREATE or REPLACE v_p5 AS

  SELECT * FROM TABLE (User1.f_provide_p5);

  I can then do a select * from v_p5 in User2 and return the view data.

  Thank you.

  Hello

  Don't bother with the pipeline and PL/SQL functions.  Everything will be easier, more effective and more reliable if you use only views.

  Privileges through roles do not create a view on a table in another schema.

  If user1 can create a view on motherlode.table_x, then user1 should have direct privileges already (or user1 must have a privilege of system as SELECT ANY TABLE).

  User1 needs the same privileges WITH GRANT OPTION in order to grant privileges on his point of view to User2.  To do this, have motherlode grant privileges to user1, like this:

  GRANT SELECT ON table_x to User1 WITH GRANT OPTION;

  GRANT SELECT ON table_y to User1 WITH GRANT OPTION;

  Repeat for each table that user1 uses in the views.

  Then user1 will be able to grant privileges on views to User2 like this:

  GRANT SELECT ON my_view_01 TO user2.

  This will NOT allow user2 directly see the motherlode.table_x.  User1 will have the power to give privileges to User2, but simply grant privileges on the view does not give User2 these privileges.

  If you don't want User1 to have this power, then create the views in the motherlode scheme, or create a new schema only for the putpose to own these views.

• Management of access to the PSO

  How should I manage access to the OSP itself (not vCenter).  I'm under 5.5 SSO.  By default, there is an [email protected] account.

  1 should I / can I change the name of this account to something else then the username who has these rights cannot be guessed?

  2. in the event that separate vsphere.local of the accounts for the 2 admins who need direct access to the SSO periodically so that it is possible to see who it was that truly connected so the account [email protected] doesn't have to share?

  Thank you!

  Hello

  In my view, it is necessary for users of the SSO. If AD goes out, what are you doing? I have an account for all the items of the SSO SERVICE. For users of physics I use AD. It is a split approach. That way if the AD goes out I can still manage and use the environment.

  I also always keep [email protected] as a user in vCenter and keep his password in a vault. It's the equivalent of root on a host computer. This way you have a backdoor when everything goes pear-shaped. If the announcement is released, how will you manage your systems? Once more to think about than the break glass.

  I use SSO to service accounts because you have half of the currently VMware management tools, so I use it for all of them. But only the service accounts and an unused admin account until a break glass is necessary (IE. AD is no longer available).

  Best regards
  Edward L. Haletky
  VMware communities user moderator, VMware vExpert 2009, 2010, 2011,2012,2013,2014

  Author of the books ' VMWare ESX and ESXi in the business: Planning Server Virtualization Deployment, Copyright 2011 Pearson Education. ' Of VMware VSphere and Virtual Infrastructure Security: securing the virtual environment ', Copyright 2009 Pearson Education.

  Virtualization and Cloud Security Analyst: The Practice of virtualization, LLC - vSphere Upgrade Saga - virtualization security Table round Podcast

• Locking ESXi 4.1 mode access confirmation no access to the vCenter Server

  Hello

  ESXi 4.1.  I see options in conflict with access to a crowd that had lockdown normal mode activated via a server vCenter VM on a host in the cluster.  The vCenter server that sits on one of the hosts in the cluster lockeddown then became inaccessible or unresponsive connectivity wise.  So no connectivity between vCenter VM or VM vCenter and hosts.  Is someone can confirm if you can connect to this host lockedown by DCUI with root and disable lockdown configuration to allow the vSphere client to then connect to the host with root and troubleshoot the server vCenter VM?

  I read in some messages that this is only possible if the vCenter VM is in place and the communication to the host.  I also read that it is possible no matter what the State of the vCenter server once Total lockdown (disabling DCUI) is not enabled.

  I have this reference of the 'The new lock in ESXi 4.1 Mode' blog http://blogs.vmware.com/vsphere/2010/09/the-new-lockdown-mode-in-esxi-41.html

  "With active locking Mode, the only direct access to the host that remains open is through the DCUI. This allows to perform administrative tasks limited outside vCenter Server, such as restarting the management agents and the display of the log files. In addition, you can also disable Mode of Lockdown since the DCUI. This can be useful if vCenter Server is down or unavailable, and you want to return to a direct management of the host. Normally, without locking Mode, any user to the Administrator role can open a session in the DCUI.  However, in lock Mode, the root password is necessary; no other user can connect.

  Can anyone confirm.

  Any other person who may not be sure these questions, I can confirm that with root credentials, you can connect to the host directly and disable the lock mode regardless of the availability of vCenter.  Only if the Total lock mode turned on, or should I say DCUI is disabled, then you have no choice but to go through vCenter or reinstall and reconfigure the network.  VM would be always available if local or have to be reassembled and re inventoried etc.