Directly access an IP of D-Link camera

Similar Questions

• Cannot install Webroot software error: problem of direct access component - should close. incompatible tfswct.exe

  Original title: Direct access component problem - must close. incompatible tfswct.exe

  I uninstalled Shield Deluxe, restarted, then tried to start installing Webroot SecureAnywhere Essentials from the installation CD.

  I did not demand the product key so no Webroot software is installed.

  How to solve the problem of tfswctl.exe?

  Hi DW_758,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Follow the steps in the article.

  Problems installing and uninstalling programs on Windows computers

  http://support.Microsoft.com/kb/2438651

  Method 2: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After the boot minimum troubleshooting steps, follow section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start and then click Run.

  (b) type msconfig and click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal Startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Install the applications as an administrator.

  HOW TO: Use the RUN AS command to start a program as an administrator in Windows XP

  http://support.Microsoft.com/kb/305780

• Just after I turn on the laptop (before that turns on Vista) I get "cannot open volume for direct access.

  Just after I turn on the laptop (before Windows Vista turns on) the following message appears "cannot open volume for direct access.  What this mean and how can it be solved?

  Thank you

  Eddie

  Hi EddieLopezA,

  ·         Which version of Windows Vista is installed on your computer?

  ·         You have antivirus software on your computer?

  This problem may occur if another utility or service, for example a virus check program or a program disk monitoring, locked the partition before you try to run the Chkdsk.exe or Autochk.exe utility.

  I have some steps that may help you.

  Method 1: I suggest you to turn off all third-party applications and check if you have a similar question.

  To do this, follow these steps:

  1. open the start search box, type services.msc and click OK.

  2. in the Services (Local) list scroll the service concerned (for example auditor of virus or disk monitoring tool).

  3. right click on the service and select Properties.

  4. change the startup type to disabled for all applications 3rd - party that could be the cause of the blocking of Chkdsk problem.

  5. click OK/apply.

  6. restart the computer.

  Method 2: If this does not help, try to change the registry value and restart the computer.

  1. click on the start search box, type regedit.

  2. in the Publisher of the registry under the HKEY_LOCAL_MACHINE subtree, go to the following subkey:

  \SYSTEM\CurrentControlSet\Control\Session manager

  3 change the Boot entry run of:

  autocheck autochk * /r\DosDevice\C: (or other)

  TO:

  autocheck autochk *.

  Note: Change the settings of the REGISTRY can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the REGISTRY settings configuration can be solved. Changes to these settings are at your own risk.  If you want to edit the registry to fix this I urge you to back up your registry before proceeding.

  Links for:

  Unable to run CHKDSK

  http://support.Microsoft.com/kb/555484 (also applies to Vista)

  Hope the helps of information.

• Intel WiDi Pro works with Microsoft Direct access?

  Our company deploys a Direct access to avoid using VPN tokens, so the use of laptop with Windows 7 without DA WiDi society construction works without any problems, but when you add DA at this laptop it stops work WiDi. He will see the WiDi adaptor and even ask the PIN code, but once to enter the CONFIDENTIAL code to connect to the screen, it will lose the connection, and then I also have to reset the WiDi dongle (we currently use the dongle Microsoft WiDi)

  For all help and advice on how to the GET WiDi work with the DA would be appreciated

  Thank you

  Wayne

  Hi Wayne,

  Thanks for posting your query on the Microsoft Community.

  That you are connected to a domain network, I suggest you re-post your query on The TechNet Forums as we have experts working on this type of questions and for you to help.

  Check out the link:

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• Direct access the 4 G/LTE Verizon's internet connectivity-related issues

  During an attempt to access remotely via a Direct access to a tablet with 4 G/LTE from Verizon, we are unable to access the internet. Before the installation of a Direct access on the Tablet, 4 G high-speed worked fine, but once the Tablet has been recreated for a Direct access, we no longer had access to the internet. A call to Verizon revealed that the Tablet has been connected to the system of Verizon, but is was not connected to IPv4 or IPv6, and whether Verizon could not move forward. Are there Direct access settings that should be addressed in order to allow access to broadband (4 G SIM chip)? Thank you.

  Hello

  I understand that you are unable to access the internet during an attempt to access remotely via direct access on your tablet.

  To better understand the issue, please send us the following information:

  1. What is the brand and model of the Tablet you are facing problems with?
  2. The problem occurs on other laptop or Tablet?
  3. You are connected to the domain network?

  If you are connected to the domain network, you can post your request in the forums TechNet from the link below:

  https://social.technet.Microsoft.com/forums/en-us/home

  It may be useful, get back to us with the required information and we will be happy to help you.

  Thank you.

• Virtual disk "Hard disk 3' is a direct access mapped lun that is not accessible

  I am currently in the process of upgrading our cluster of ESX 4.0 U1 to 4.1. In the process, I came across a physical MSCS 2 with RDM cluster. I stop the VMs and vmotion can them between the hosts of 4.0. Now as soon as I update hosts 4.1 I cannot vmotion the VMs to these 4.1 hosts. The error I get is: "virtual disk"drive hard 3' is a direct access mapped lun that is not accessible". I found an article KB http://kb.vmware.com/kb/1016210

  who speaks ensuring that LUN number is the same in the presentation of all ESX hosts and I checked, it is the case, moreover, as I said vmotions does not always work for guests, that I have not yet updated. I have not tried anyone all LUNS and re - introduce, don't know if I should try that. Looking for suggestions.

  Thank you
  greendxr

  You have to poweroff the node, remove the RDM drives, migrate the virtual machine, and then add again in RDM disk.

  RDM LUN must be on all hosts.

  André

• HyperDrive 5 and 'fixed Direct Access SCSI-2 device.

  Colleagues ESX - ers,

  I think to buy a very fast RAM-disk, the "HyperDrive5", in:

  http://www.hyperossystems.co.UK/

  It is fully compatible SATAII (and therefore must be recognized by my E200 very well). It is, will be virtualization ESX 3.5 as SCSI drive slow down questions too? My server lists current as disc:

  da0: fixed Direct Access SCSI-2 device

  da0: 320,000 MB/s transfers (160,000 MHz, offset 127, 16-bit),

  Tagged Queueing active

  Thus, when you buy the ramdisk, fixed Direct Access SCSI-2 unit of Vmware will be the bottleneck? Or it dimensionnera upward, in speed, according to the new features of the psycical (much faster) of the RAM disk?

  Thank you

  -Mark

  Hello

  If it works fine, but SAS, SATA, SCSI and RAM all have different performance characteristics. It will not change the other. The controller will be your factor limiting.

  Best regards
  Edward L. Haletky
  VMware communities user moderator, VMware vExpert 2009
  ====
  Author of the book ' VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.
  Blue gears and SearchVMware Pro items - top of page links of security virtualization - Security Virtualization Round Table Podcast

• Access no longer work after the abduction of (Server Essentials 2012 R2) Direct access

  Hello

  Ive been running around access to the company I work for, its been working well for almost a year.

  I removed a direct access and remote access via the menu "Roles and features" in the Server Manager, since then it is not working and when I try to Config/repair I get a message saying "anywhere access to your server is blocked.

  Ive updated the firmware on the router and the manual configuration of redirection to make sure it wasn't a problem with uPNP port

  Should I check that I can be removed when I removed direct access? Or what I need to change?

  I'm sure I did something stupid...

  Thanks :)

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Acquisition of images using PCI-1426 and Camera Link Camera

  Hello

  I am writing a program to capture images of a Camera Link camera via the PCI 1426 acquisition card in LabVIEW. The problem that I am facing is that I am unable to find the correct controls in the functions palette to start the image capture. Could someone tell me please how much control I'm supposed to use?

  I've worked on similar request sometimes back, I used IEEE 1394 camera, so once I found the correct block diagram controls I should be able to go from there.

  Thanks in advance,

  Sandeep

  Hello Kristen,

  Thanks for the suggestion. I was able to solve this problem. I think that was what was causing the problem I have LabVIEW 8.6 installed on my system and he had the Vision Acquisition System (VAS) 8.5.1. But, once I installed VAS 8.6 I saw the IMAQ in the functions palette.

  I'm guessing that LabVIEW 8.6 does not recognize the toolboxes of previous versions.

  Sandeep

• to try to correct a disk check error "cannot open volume for direct access.

  OK, I'm unable to run check disk utility I get this ' impossible to open the volume for windows direct access finished disk checking "I tried everything micrsoft has on there Web site. and the system is updated with service pack 3

  Boot from your Windows XP (optical) installation media.  Assuming that your BIOS is set to boot from the CD first (otherwise, ensure), you will see a message in the sense of «Press any key to boot from CD...» ».  Do as he says a few seconds (I usually have to press the space bar).  After a lot of clatter and echo, your property see the Windows Setup screen.  Type 'R' on the first line.  Yet once, banging and rattling and you you have started the Windows XP Recovery Console from the installation media.  First of all, it prompts you for the number of Windows Setup (which is usually C:\WINDOWS).  The model number of the directory of correct installation and you ask for the administrator password.  Type the word or press ENTER if it is not a.  You will then be prompted for the Windows XP Recovery Console.  HELP will give you a list of available commands.  MAP will show you the list of BIOS (not Windows) of the drive letters.  Type:

  CHKDSK/p :

  To run the check disk (not /f or/r).

  Good luck!

• When trying to start the disk check procedure, I get the answer, "cannot open volume for direct access. How can I fix?

  I get the above answer everytime I turn on the computer. (This is with AutoCorrect blocks checked). If I leave blocks unchecked, it follows a procedure 3 pass without rebooting and does not produce a result.

  * original title - to try to start the procedure of checking disk I get the answer, "cannot open volume for direct access. How can I fix? I ran the GET Microsoft virus check tnd an own result.*

  The application-specific permission settings do not authorization for the application server COM with the CLSID
  {DCBCA92E-7DBE-4EDA-8B7B-3AAEA4DD412B}
  the user NT AUTHORITY\SYSTEM SID (S-1-5-18). This security permission can be modified using the Component Services administrative tool.
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_comp_exp.mspx?mfr=true

  In the opposite case

  http://blog.ray1.NET/2008/01/WinXP-SP3-DCOM-system-error-dcbca92e.html

  http://TechNet.Microsoft.com/en-us/network/bb545879

  http://www.blackviper.com/wiki/Network_Access_Protection_Agent

• prevent direct access via webmail

  I want to prevent direct access to common accounts through webmail. for the user X interpreter should be able to display "itsupport" via webmail only after have connected you to its indivisual ID and then open new window https://webmail.domain.ae/Exchange/itsupport and prevent it directly access itsupport via webmail as user X has the permission to access the itsupport

  Thank you

  Hi nouraAJ,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please ask your question in the Forums of Exchange Server.

  http://social.technet.Microsoft.com/forums/en-us/exchangesvrgeneral/threads

• Error: "cannot open Volume for Direct access" is displayed when Chkdsk runs at startup

  Original title: Edit/Fix key in my registry

  CHKDSK keeps trying to run during startup, but "cannot open volume...". "If I can solve this problem, I want to put it in the manual, not automatic.      My registry key: "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\rchelp is missing.   Can I remedy this by creating a text file with an REG extension and if so, where can I find the exact measurements to do?  It is the DOS Cmd or in Notepad?

  Hi BarneyBear,

  1 did you allow that chkdsk runs successfully at the start of the system?

  Editing registry is not necessary here. We recommend you to check if the disk check is scheduled.

  This problem can be solved by installing the latest service pack Windows XP.
  See the error message "Impossible open Volume for Direct access" When Chkdsk runs at startup

  See also, Chkdsk.exe or Autochk.exe starts when you try to shut down or restart your computer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot open volume for direct access?

  OK so I have windows vista 32-bit home... and I installed this program from avg that solves all the problems on the computer... Well now when I boot, I get a cannot open volume for direct access... and I loaded my computer finally and its telling me everything is corrupted?

  Hello

  I'm sorry but most of the posters, which I am part, who come here do not believe in using Tuneup Utilities, registry cleaners, etc. to improve performance or solve problems.

  They are completely unnecessary.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  Or, if you don't have one, borrow a DVD of Microsoft Vista, not a recovery disk and you could do a upgrade in repair facility.

  "How to perform a repair for Vista Installation"

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  And I have contacted AVG or their Forums as you say it was their program that caused the problems.

  http://free.Avg.com/us-en/support

  See you soon.

• direct access to the modem point

  is it possible to directly use the access point with a modem.  my router seems to slow down my internet connection.  If I connect directly access point, I can still access the internet with my laptop, but my xbox comes up with an error "no IP".  any advice?

  Yes and NO

  An access point is designed to be a network of signal and therefor if the WAP54G was connected to your moen he will be part of the public network like all clients attached to it. This means that all customers should also public IP provided by your ISP.

  Your ISP probably would not be in favor of offering more than 1 IP because there is a finite number of available IPv4 IP and there is a growing shortage of IPv4 IP addresses. This is the reason why IPv6 is developed.

  Concerning

  Fred