Disable DHCP on WRTU54G behind WRT54G, impossible to get the blue light
I spent several hours today trying to set up my second router (WRTU54G) behind the first router (WRT54G) with the DHCP offshore on the second router, but blue light don't come. My first router is connected to the modem. There is nothing wrong with the phone service, it works with a LAN WAN Setup on my routers and the blue light comes on. But I'm trying to get everything on my network to answer and turn on sharing, so I'll try the config LAN to LAN on the two routers with DHCP disabled on the second. No blue on light. I also tried the Bridge mode on the second router but that did not work. By browsing these forums, I opened the ports 5060-5061 and 16384-16482 on my first router but I don't know what IP address to assign them. What I'm trying to do is to use my router second, WRTU54G of VOIP, like a switch, but also use it for telephone service. I know that I can just swap the routers and that should work, but y at - it another way?
Thanks for the reply, but that has not worked for me. But I finally got to work now, after some more googling and play with the settings. I have stuck on the 'Bridge' on the WRTU54G mode but kept the connection between the two routers on LAN to WAN connection. This didn't work at first but after only 20 minutes to leave and the blue light came all my computers are on DHCP IPs the first router too.
Tags: VoIP Routers
Similar Questions
-
How to disable the blue light on Chicony USB 2.0 Camera?
Hello
My first post. I have Toshiba laptop with end of Chicony USB 2.0 Camera camera built-in, there a blue light. I put t want this blue light when I open the messenger or ICQ and talking with one my girlfriend. The blue light is turn on and I don t like it.
How to disable, because it dazzle me
End thank you cordiallyAs far as I know the blue light can t be disabled and it will show if the webcam is used.
If you use a Messenger you use the webcam too?Normally if you write only with one person in the blue Messenger is not light. On my Satellite L300, I also use ICQ, but I don't see the blue light that if I use the webcam.
-
After the Windows 10 update (don't like it) and go back to Windows 7 Home premium, impossible to get the Windows Update to run.
Sorry, but KB3153199 has replaced two times at the same time. It takes the new version of the Windows Update client to correct known issues.
http://support.Microsoft.com/kb/3161608
Manual installation requires a continuous search to be interrupted. The value of the automatic updates to "never check updates" and then restart Windows.
Best regards, VZ
-
With the help of LR4 with Windows 8 - impossible to get the images to desempilement.
Using LR4 with Windows 8 - impossible to get the images to desempilement.
Right click on the picture, select stacking, select Unstack
-
Just downloaded latest updates Camera Raw update for use with my new Sony RX100 M3 but still impossible to get the RAW files to open it. Any suggestions?
Nevermind, I finally got it to work, thanks!
-
Win 7 - impossible to get the screensaver to work
Windows 7 works very well so far, but I can't make the screen saver turns on with or without putting a time intreval. Even when I select the option for the login screen to display when the screen saver is cut... usually not work either.
I set and reset the screen saver mode in the section 'Customize' to prevail, any ideas?
the information provided, you are using a 64-bit machine x,
have you downloaded the windows7 x64bit version
also when you burned the iso file to a disc did you have burning program check you the diskas I know that its possible to have defective sectors on the disks.
so its worth it to take a little extra time and do check Fujitsu Siemens MS-6567V2 2.0 Board by your burning program: clock Bus Micro Star MS-6567V2 2.0: 133 megahertz BIOS: American Megatrends Inc. 07.00 T 06/04/02 2.40 gigahertz Intel Pentium 4 8 kilobyte primary memory secondary memory of the 512 KB of cache cache of 512 megabytes installed memory 1024 megabytes installed a Slot memory ' 0' has 512 MB Slot ' 1' has 256 MB Slot ' 2' has 256 MB Slot '3' is empty Standard VGA graphics [graphics card] generic PnP monitor (15.7 "live, June 2004) NVIDIA nForce (TM) MIDI UART Realtek AC 97 Audio unsupported Standard Game Port PCI CX11252 - 11 Modem IC Soft more IP100A 10/100 Fast Ethernet adapter Dhcp Server: none responded Microsoft 6to4 Adapter Microsoft ISATAP Adapter Microsoft ISATAP Adapter #2 Realtek RTL8139/810 x Family Fast Ethernet NIC courtesy of the GeForce4 http://www.belarc.com/free_download.html MX 440 - SE AGP 8 X Fill Rate: triangles per second: memory bandwidth: Maximum memory: reserve 1.1 billion Texels/s 34
-
Impossible to get the music from iTunes to iPhone
Can't get music from iPad iPhone iTunes
You cannot copy music directly from an iPad to an iPhone. If it's the iTunes purchases you can redownload it via the tab purchased in the iTunes Store on your phone. otherwise, sync music from your computer's iTunes library to the phone.
-
Tecra A11 - impossible to get the FN keys to run on Win 7
I had to do a fresh install of Windows 7 on my Tecra A11.
Everything works fine but I find that I really really miss the ability to activate the trackpad turn off and turn on the wireless and turn off.
I'm guessing that the only way to do it would be to reinstall this program that connects the FN key for the numbered function keys.
I don't know what to call it so I don't know what to look for. I want to be careful and not to install more that I need.
Y at - it program or how I can get this resettled function?
Thank you
Susan
p.s. This forum very well, I found how to turn the touchpad off when a mouse is installed, but if I don't have a mouse attached and it's off, I'm in a mess :)
Hello
The FN keys are controlled by VAP (value added package) and the Support of Flash memory card utility.
Install the VAP first and check if the FN keys work. If it will not work then you should also try the Flash Cards Support utility to get this FN buttons working.
Flash memory card Support is located in Satellite L500 or other subsequent seriesWelcome them
-
Impossible to get the touchpad to work - Tecra M2
I have unknown device in my device manager.
Touchpad does not work but can use the usb mouse.
ALPS Touch Pad driver and Toshiba double pointing device utility installed.
It is a Tecra M2.
David
It is not necessary to create a second thread on the same topic.
You must follow your first thread here:
http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=179662 -
Impossible to get the USB flash drive to work
I have a new Satellite L500 with Windows 7 and it will not recognize/install the USB flash drives. A msg comes up saying "software device driver has been properly installed. I tried several flash drives - they are OK & work on other machines - including an another Toshiba running Windows 7.
Other devices work in the USB ports, so the ports are OK.
Windows cannot resolve the problem, I have checked all USB drivers are updated in Device Manager & made a system of analysis of file without success.
The Bank recommended a reload & restore factory default - other options?Have you installed driver chipset?
Your laptop comes with Vista or Win7?You have just upgraded to Vista or Win7 clean setting?
-
In Windows Movie Maker HELP "FOR THE DURATION of the CHANGE" 2. ' "says to" select title you want to change the duration. How to "choose" the title? The title as a RECOVERY when the arrow is hovering a square bubble appears showing the title and 6.7 seconds. No trim handles appear. A high blue and the low line components appear, but I don't know what that means because it is not graphic design help pages. I would like to extend the superposition of the title from 6.7 seconds to 36 seconds. Please give me some help you can. It's frustrating!
Thank you
Ginger B
Hi Ginger B,.
Windows operating system you are using?
If you use Windows Vista, you can read the following article and check if it helps.
Getting started with Windows Movie Maker
Hope this information is useful.
-
Impossible to get the recovery disc Vista for DV7-1020us notebook.
I intend to install a new hard shore (750 GB) in my Pavilion DV &-1020us notebook. I use Vista 64 bit OS. Software does not offer me the possibility to make recovery disks. I can back up my files. The HP site says my computer does not recognize my serial number. I entered the serial number several times. The message I get is "HP is unable to find the desired page. To order Windows 8, a comprehensive program is of 90.00. The only CD that I have fallen on the Internet are to save the files. I appreaciate help on this.
Hello
You can order on the following site:
http://www.computersurgeons.com/SearchProducts.aspx?SBT=dv7-1020US&BKM=results#results
Kind regards.
-
Impossible to get the actual thumbnail image on jpeg files icon
Original title: JPeg file icons
I can not the icon of the actual thumbnail image on my JPEGs, only the jpeg itself icon. I tried to change the size of the icon to adults, as suggested by one of your readers, but which did not help. I also double checked to ensure I have "thumbnail" check in the view menu. I made sure the "always show icons" is unchecked in Control Panel. Help? All of the suggestions. I am running Windows XP.
Hi Mjoan,
1. don't you make changes before the show?
Try these steps and check the result.
Step 1: Check if a non-Microsoft program is the cause
a. open the article: http://support.microsoft.com/kb/310353
b. method 2, follow steps 1 and 2, and then restart the computer to see if the problem persists.
c. If the problem does not persist in the boot, then follow step 3 and step 4 to find out which is the origin of the problem, and once you have found the culprit, uninstall the program and check the result.Note: Don't forget to follow the steps in the steps to configure Windows to use a Normal startup state"" section.
Step 2: We also recommend you scan sfc (System File Checker) to see if any system file is missing or damaged. To do this, try the following steps:
a. Click Start, click Run, type cmd and click ok.
b. at the command prompt, type sfc/scannow and press ENTER.Note: You will be asked to insert the Windows XP disk, if a file is missing.
For more information, see Description of Windows XP System File Checker (Sfc.exe)
Visit our Microsoft answers feedback Forum and let us know what you think.
-
Impossible to get the Vista machine see computers network XP Home
Home network with DLInk DIR - 655 wireless router which connects the top of Office XP (2 printers connected to the desktop computer), laptop XP and 1 Vista laptop 1. Now computer Vista laptop sees no, desktop or laptop XP or good printers that file sharing is turned on (steps of Microsoft).
HelloA computer running Windows XP can be detected and appear on the network map, you may need to install the Protocol Link-Layer Topology Discovery (LLTD) on this computer.
To download and install LLTD, visit this link:
http://support.Microsoft.com/kb/922120Once the LLTD is installed on the XP machine, restart the computer and check the result.To solve the problems of network connection, check the steps in this link:
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problemsI hope this helps.Kind regards
Syed
Answers from Microsoft supports the engineer. -
College Dorm Internet - impossible to get the printer connected wireless
First of all, let me say that I have 3 OfficeJet Pro 8600. The printer of love.
Second, here is a part of the background of my situation:
Bought OJP8600 for son go to College. In the dormitory, it is wireless which is encrypted.
WiFi@OSU is a front-end which feeds on the more robust secure portal, which leads to connect to osuwirless.
Can easily get its HP Pavilion on the osuwireless network. Name of user and password... no sweat (through the secure portal).
But when I configured the printer... She grabs the WiFi@OSU router and he seems happy. Problem is that computer of this son is on the osuwireless network. When I try to select xxxwireless on the printer, I get an error of encryption or application not valid. Duh.
Then... I'm guessing that a network administrator will need to add the printer?
I used a cable ethernet to connect to his laptop computer and that works. Awkward, but works. Suppose that I could also connect via USB, but also clumsy as it is to connect the wire whenever you want to print.
Thanks for bearing with me... here's my questions:
1. cannot get the HPDirect to work... maybe I don't understand what he does? I can see the host name in internet connections, but can not get the phone to connect to anything mode other than "limited".
2. a BlueTooth adapter would be an option? I know that my 8600 didn't BT resident.
Thanks for reading and your suggestions.
M61
Hello
You try to open your printer can be used by everyone. The safest way is the use of USB cable.
Kind regards.
Maybe you are looking for
-
unconscious local copies of the songs iTunes
I have over 12,000 songs in my iTunes library, which also houses the library music to iCloud and synchronized between my devices. On a Mac, the entire library is already downloaded and resides in the folder that is selected in the media folder in iTu
-
Satellite P10-833 stops working if the cooling fan is working
Mr President:1problem in my pc when im playing any audio or video after 3-5 min., it stops for about 30 seconds, then the fan starts on so if the fan it will be disabled after playing the video or audio said. 2ndeven with the above, when I have somet
-
Tornado of Washington area, Illinois erased all the info to the computer's printer
Washington Illinois Tornado caused computer crash, wipe all the drivers on my computer. Now, try to reinstall but am running out of problems with the hp site that requires the purchase of the pilot program to do. Have given everything I can to my n
-
Windows 7 - updates errors - Code A 80071, 91 and Code 80070643
Windows 7 - updates errors - Code A 80071, 91 and Code 80070643
-
I accidentally put my pictures folder in the bin and emptied. How to make a comeback?
II accidentally put my pictures folder in the bin and emptied! How to make a comeback?