Disconnect the cable in a VI script

How to disconnect the wire between two terminals in a VI script?

Get a reference to the thread and call the Delete method. If the wire is connected to multiple receivers, you can get references to the source and (other sinks), remove the wire, then reconnect to all receivers other than the one you want to disconnect.

Tags: NI Software

Similar Questions

  • Equium 2000: How to disconnect the cables strip of motherboard

    Hallo,
    could you please someone describe to me how to disconnect the two flat-band-cables the Equium 2000 with the low Group (readers) motherboard, that the connectors don't get corrupted.

    Thank you!

    Harald mueller

    Hello

    I'm not 100 sure that cables say exactly, but at both ends of the connector, you should see little "clips" or "parentheses". You have to put on the side. So normally it should be possible to pull the cables. But if you do, you should be carefully.
    But if you have no experience of these things, you shouldn't do it. In this case, the best way is to ask the guy to service for assistance.

  • Satellite L450 - connection loose if I disconnect the cable

    I just tried to configure my modem on my Satellite L450 wireless and it works well with the ethernet cable, but as soon as I disconnect I lose it.
    I tried 3 cables but nothing.

    What can I please?

    Hi ElaKeen62,

    I m a bit confused now... As a first step, you wrote that your WLAN car works well, but then you wrote something on the Ethernet connection and you have tested 3 cables?

    What exactly is your problem?

  • LAN broken or disconnected the cable

    the icon in the LAN system tray has a red X and says a network cable is broken or disconnected. my laptop network will connect by mistake. I visually inspected son and they seem ok - is there a way to be sure if it is causing me to lose my connection. appreciate any suggestion

    1. use a different cable

    2. go to start, Control Panel, network connections, right click and choose repair.

    What happens now?

    3. go to start, then right-click on my computer and select manage, select Device Manager, are there points of yellow exclamation that will tell you if there is a problem with a driver?

    4 do the following if you can't connect to the internet, make sure that your system is clean by running a scan with your antivirus which is this?

    5.

    Click Start, run and enter in the box:

    Msinfo32

    Click OK, and when the system info summary appears, click on edit, select all (Ctrl-A), copy (Ctrl-C) and paste (Ctrl-V) the information back here in your next reply.

    You can change the personal information.

     

    Download, install, update and scan with these full free malware detection programs:

    Malwarebytes (MMFA): http://www.malwarebytes.org/products/malwarebytes_free

    SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

    Remove all found, restart, and run again until analyses race clean, these can be removed later if you wish.

  • disconnected the cable plug location unknown

    I'm working on a HP Slimline S5113W, that does not illuminate. I deleted food and tested it and it seems OK. I put it all back together and I have a son that I don't know where to put. It's the front set of SD USB card, two blue and black wires ending with a small white connnector. I can't find any documentation as to where this could go. Anyone know?

    Are you absolutely sure it's 2 blue and 1 black in a white connector?

    If it is 1 blue and 1 black, it does not connect to what in my HP s5120y (even on board and installation). This is the connector is wire-bound into a beam and weighs disconnected.

  • My laptop screen becomes empty whenever I disconnect the plasma

    Recently, I connected my computer laptop to LG plasma to see a movie (using RGB output) and changed the accodringly to display definitions. However, when I disconnected the cable from the laptop, the laptop screen became blank. When I reconnect the cable - I see the laptop screen (even if the plasma is off). Now I'm stuck to work with a cable connected to nothing...

    When you restart the computer, I see the screen, it disappears when windows comes on.

    I've redefined (by using windows + P) the computer screen only - did not help. I've updated the display adapter and monitor in Device Manager - did not help. No virus detected; Nothing to do with the BIOS...

    Ideas please?...

    Hello

    I suggest you to uninstall and reinstall the drivers to display the computer manufacturer's website and check that I get no help.

    Updated a hardware driver that is not working properly

    http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

     

    Update drivers: recommended links

    http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

  • My computer is constantly disconnected from the internet and to reconnect I just unplug the cable for less than a second and it starts to work instantly.

    My computer is constantly disconnected from the internet and to reconnect I just unplug the cable for less than a second and it starts to work instantly. Does every 5 to 10 minutes and it gets frustrating. It is not the cable modem because it is constantly connected, and I repeatedly checked.
    I have this problem with all programs on the internet and she does every day and probably every 5 to 10 minutes.

    Hello

    Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
    Update your WiFi drivers on computers. How you are positioned in the router? Are there
    obstacles in the path?

    Actually try updating your driver and disabling the network logon.

    Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
    version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
    Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    Download - SAVE - go where you put it - right click – RUN AS ADMIN.

    You can download several at once however restart after the installation of each of them.

    After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
    manufacturer of system become your backup policies).

    Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
    updated drivers.

    I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
    are almost always old, and you can search drivers manually as needed.

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    ------------------------------------------------------

    Make sure you know the details of connection to your wireless router - SSID and password.

    You lose connection when you do and have to redo your logon.

    Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
    lower left click on merge or delete network locations - REMOVE all instances of your network (and the
    others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

    -----------------------------------------------------

    Check this box:

    Strange problem with Internet under Vista
    http://www.catonett.com/blog/archives/194

    Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
    http://support.Microsoft.com/kb/928233/en-us

    ----------------------------------------------------

    And:

    Network connection problems
    http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • Unable to connect to the internet (using a wired connection or wireless) after a power failure, error "the cable network is disconnected"

    After a power outage, I can not connect wireless (cannot connect even with the wired ethernet cable); get message "network cable is unplugged", which is not.  The cable modem work properly in wireless mode with two other computers.  System to an earlier date of reload and change the cable has not solved the problem.  Running Windows XP.  Any suggestions?

    Hello

    I suggest to follow the steps provided and check if it helps.

    How to troubleshoot the following message appears in Windows XP: "a network cable is unplugged": http://support.microsoft.com/kb/910389

    Hope this information is useful.

  • Tungsten E2 how do disconnect the USB hot sync cable without damaging it?

    I just got my Palm two days ago. After the loading of the next day, I got the software loaded and to implement the E2. After the hotsync, I couldn't unplug the cable from the Palm. I didn't force of fear that I would be damaged. Is there a trick? Can someone please help?

    There is no trick. It is very hard for the first few times you use it. Just pull evenly and it will be fine.

    Post back if you have any other questions.

    Message is about: Treo 800w (Sprint)

  • Unable to connect to the network in an OS Win 7 comments when the cable disconnected

    Hello

    I have a Win7 x 64 host with Workstation 7.0 executes 2 guests - is also a Win 7 x 64 and the other is a Win 2003 R2 x 86. Both work quite well when I have a cable plugged into the host network, but when I unplug it, the Win 2003 comments always connects to the network local vm end (for example I can ping the host and I have a correct IP address with ipconfig) while the prompt of Win 7 says "unidentified network".

    I have something special for the networking of comments (or even the host by the way) and that the guest Win2003 worked 'out of the box"that makes me think that the Win7 to work also with some small configuration changes somewhere - someone can help point me in the right direction?

    See you soon

    Dan

    If both are NAT, both should have the Internet connection if you have removed the cable, because NAT virtual network connects to each host TCP/IP stack.

    Are you sure? It really sounds like a bridge and the other is NAT. If you unplug the cable from the network status of the guests should not change. If in doubt, post the two guests .vmx files.

    AWo

    VCP 3 & 4

    \[:o]===\[o:]

    = You want to have this ad as a ringtone on your mobile phone? =

    = Send 'Assignment' to 911 for only $999999,99! =

  • removal of the cable for material test

    Hi I want to do a test om my IMac equipment

    I am connected to the internet with an ethernet cable plugged into my router and the iMac.

    Do I have to disconnect the ethernet cable to try out material?

    amandafromwr wrote:

    Hi I want to do a test om my IMac equipment

    I am connected to the internet with an ethernet cable plugged into my router and the iMac.

    Do I have to disconnect the ethernet cable to try out material?

    NO.

  • Replaced the cable. Now, the screen does not work. What could be?

    The cable coming out of the back of my monitor Apple Thunderbolt Display is fraying. I decided that rather than risk a short at a certain point, I preemptively replace the cable. On iFixit teardown photos, I decided to replace the cable coming out of the back of the screen myself instead of paying almost $200 to get an Apple service provider to do that here in Bangkok. Bought the cable on AliExpress for $12. It replaced. And... no dice. Screen has not come.

    My setup

    [MacBook Air]-[Thunderbolt Display]-[drive Thunderbolt]-[Cinema Display]

    with a key USB drive and Ethernet connected to the back of the Thunderbolt display

    Already tried this

    • First impressions were that the cable was defective. But then I noticed Ethernet came the USB has been mounted, Thunderbolt was mounted drive and after a reboot, the movie screen come also. Obviously, the cable has been working very well.
    • Second thought was that I'd neglected to plug some cables that connect the LCD to the main logic board. I checked. Seemed fine.
    • Third was maybe the serial number of the cable was somehow connected to the main logic board. So I put the old cable. Still no screen.
    • Tried to connect the screen with a Thunderbolt external cable, everything worked as well but still no image on the screen.
    • Tried more than 30 seconds and 3 hours disconnected as a "reset" of the screen. No change.
    • Restarted my laptop. No change.
    • Thunderbolt Display well plugged the drive and then into the MacBook, so change the sequence of the devices. No change.
    • Information reports under "Thunderbolt" the entire chain of devices, but under "Graphics/displays" system displays only the internal screen and Cinema Display.
    • Using the newly purchased cable as a Thunderbolt external cable works fine too.

    Question

    Does anyone have suggestions on what to try next?

    The logic card goes into a sort of locked mode when you replace the cable?

    Is there more than 3 flat cables connection + connection to the land between the Panel and main Board?

    Although there is no reason to think that this has been, how to test LCD screen still work given all these flat cable connectors?


    Note: There is no Apple here store.  Apple authorized service providers are without help. He suggested to replace the cable and the Panel at a cost that is almost the same as the purchase of a new screen.

    Some of the cables that connect the LCD to the main logic board, are very short. Careful lifting the LCD, because it will go away with strength cables once that raise you it more than 2 to 3 inches on the side of the camera module.

    The shorter cable of all is the LVDS cable. A short cable with gold plated connector. Although I have had reconnected the cable on the side of the logic board, I had wrongly assumed that the other end of the cable was stayed connected because all the band used on. Someone with experience of fixing these things said of his town for this cable to unravel by force and to be sure to check both ends of the cable. When I peeled back the tape, I found that he had indeed been disconnected. Reconnect, fiddling with the tiny workspace to get the logical side of Board of Directors of what properly fixed cable again and we were back in business.

    Apple authorized service providers here in Bangkok have quoted me $200 to replace the cable. I ordered the replacement cable Thunderbolt Display off AliExpress for $12.50. It was really simple to replace the cable, just to keep an eye on this darn LVDS cable opening to the top of the screen!

  • Disconnect Ethernet cable internet on Macbook

    Just installed a Netgear AC1200 Wireless Modem Router.

    We have a PC, a Surface and a Macbook Pro.

    WiFi works well on all of these devices.

    Wired is very good with the PC, but when connected to a Mac to another room (by ethernet USB adapter), the internet connection to the Mac becomes invalid after a short while (about 10 to 20 seconds).

    This cable has worked well with our old Belkin modem just Twitter.com.

    Have you tried cycling the modem, cycling Mac, disable WiFi on Mac, by pressing the wireless button on the modem.

    Is this a problem switching? It seems that as soon as the Mac sees the cable it disconnects from the network.

    Great to have WiFi working but we bought this new modem to be able to easily turn off the WiFi and just use the cable connections when we are in our office.

    I'm certainly not gifted technically, so hope there is something fairly simple to do. Would appreciate some advice on how to solve this problem.

    OSGC

    Thanks for your help Darren. Problem is now solved. Has been a fortuitous error in a single link cable.

    B

  • Try to get the cable replaced

    The coating of son came away from the connector. Apple say it's accidental damage!  The cable is 3 months old. It's not like I fell and broke the screen.  How a lower cable that is not suited to the purpose considered accidental damage?  How can I get it replaced for free?

    It's a user help user forum, we are users like you and have no real power to Exchange or to change the Apple warranty policy

    That being said

    I have and always use

    1 generation iPod touch with the charger cable 2007

    3 generation iPod touch 200 X whatever with the charger cable

    iPhone 4g with cable

    iPad 2 with the charger cable

    iPhone 5 c with the charger cable

    the oldest is a little disconnected at the level of the pin30 connector but still work I use it at work mainly

    When I disconnect my cable ios I always! Remove the plug, never the cable if you pull the cable it will activate the brakes sooner rather than later

    use the comments to request guaranteed for life for apple cables

    http://www.Apple.com/feedback/iPhone.html

  • Lenovo ideapad laptop z500 won't start without the cable connected

    Hello

    My z500 cannot start without power cable is plugged. In general, a few seconds after I saw the lenovo logo, the system stops suddenly as if the battery was removed.however, if on that I connect the cable to the laptop and power, all right, I can enter in windows 8, or ubuntu, after I enter the OS, I can disconnect the power cable without any battery problems.the is healthy and can last for more than 2 hours. Is it someone has an idea what is the problem and how to solve

    so far, I have tried the following methods:

    1 update BIOS

    2 firmware update of the battery

    3 reset the BIOS

    None of them worked for me

    Hi maoxiaomin,

    Thanks for posting back.

    Sorry we could not be of additional help and please contact our service, if you need more help please do not hesitate to post in the forums.

    Concerning

Maybe you are looking for

  • IMac broke

    Hi all About 3 years 21' imac my mom stopped working a month ago. The local apple service centre that he needs a new power supply and new logic board, it would cost $1100. I took it to the apple store to see if they could fix it for cheaper (or free)

  • How can I uninstall windows 2000 Professional, windows xp home edition partition

    at present, there are two windows on my pc, I want to remove windows 2000 Professional but finding enough dificult to do, it causes my pc to slow down.

  • Contacts of MSN messenger SPAM that cannot be deleted

    I have a contact on my windows messenger which is a touch of spam that I've blocked but can not remove from my list. The message said: "you can't delete this contact. Please try again"or it closes my Messenger.

  • Windows Easy Transfer has not moved during my emails

    I tried to use Windows Easy Transfer, with a cable to transfer for Windows 7, to transfer files from my old computer runnning XP to a new Win7 running.  E-mail account settings MS Outlook, contacts and emails has not been transferred.  I can't work o

  • Half height half length for Proliant Microserver n36l video card

    I try to use a pci-e graphics card to fit my hp proliant microserver - 633724-421 source n36l. The card I have identified is a Sparkle nVIDIA GeForce GT 520 1 GB DDR3 VGA DVI HDMI PCI - E card. I wish only to use the HDMI output, removing the output