Display screen is reversed: black screen with white letters

Similar Questions

• NTLDR compressed do not restart configure disk comes with blue screen with white lettering

  an error crashed has been compressed ntldr tried to restart anything tried safe mode nothing if I get out of hard disk and I put in a new and buy windows 7 can use that new computer or is it worthless

  You have a Windows XP cd?

  To "decompress" ntldr just start on the Console recovery and the question of the
  sequence of commands (pressing after each):

  CD.
  ATTRIB - C NTLDR.

  You also can remove the disk and get in another computer and unzip the file via the GUI of Windows Explorer, right-click on the file and select Properties, then click the Advanced button.

  John

• HP Jet 7: Black screen with white lines on the HP 7 stream

  I bought my HP 7 stream about 2 years ago and I'm now a black screen with white lines whenever I turn on the tablet.

  Can you kindly help.

  If that's what you see immediately when you turn on, the graphics have not to the Board of Directors.

  These tablets were dropped after the first year of release, and it would not be worth the cost if it could be repaired.

  I'm sorry.

• HP Pavilion laptop g6: black screen with white cursor, connect

  My laptop is a few years old and today after I log in, I get a black screen with a white cursor. I read a few threads on the forums and have tried to take the battery out and pressing the button for 30secs-2mins (tried twice). I can access everything ok in Mode safe, so made a malware bites scan & clean registry. No maleware was found and I rebooted, but always the same black screen when you connect in normal mode. I tried to access the Advanced tab in the BIOS to make the test hardware, but I do not have this tab. I'm out of ideas. Help, please

  B_S2

  Hello;
  
  Let me welcome you on the HP forums!
  
  As it works OK in safe mode, then it's SOMETHING that is loaded at startup which is screw up the display.  Could be a runtime program. could be drivers, might be a Service.

  No easy way to tell.

  Demarrer start in safe mode, type MSCONFIG in the start area.  When that opens, turn off ALL startup items. Reset.

  The PC now work, if one (or more) of these numbers - and you have to go through a tedious process of re-enabling them one at a time until the PC fails again.  The last of them that you re-activated was the problem.

  Here is a tutorial on how to do it: http://www.howtogeek.com/74523/how-to-disable-startup-programs-in-windows/

  If the PC still does not work with all startup items disabled, then return to msconfig and click on the Services tab.  Check the hide services Ms.  Then turn off half superior Services.  Reset.

  If the problem is resolved, you will need to go through a tedious process of reactivating a Service at a time until you find the one that is the problem.

  If the problem is not resolved, turn off the other half of the services.  Repeat as above.

  No easy way to do...

  Good luck

• Boots Vista black screen with white cursor and nothing else (Black Screen of Death)

  After a download from Microsoft update last week, my system has rebooted. He first had a screen blue error, rebooted, reported a disk error and automatically run CHKDSK. Since then, the system has started a black with white slider screen and nothing else. This happens at startup options (Normal, safe, safe with the last command good known configuration). Not even sticky keys would come to the top. CTRL-Alt-Delete, Ctrl-Alt-Esc and all other keys has nothing did. Even with a right click.

  I searched all over the web for solutions. I found (and tried) several over the past week, but nothing has worked.

  Here's what I tried...

  F8 held key on boot to the top and entered the startup recovery. Ran of recovery. Initially so found of disk errors. Those fixed. Then he said he could not repair the system and reported two pilot errors.

  Tried system restore. He said that I had no restore points (even if I know that I had before).

  With the help of recovery options, I went to the command prompt. Asked to RegEdit and load the Software hive. Checked the connection entry Windows NT; made sure, it has been set to explorer.exe

  The system, checked RpcSs Key hive. Already the NT AUTHORITY\NetworkService value

  Renamed event connects winevt and not create the Logs folder

  Removed the hard drive. Attached to another system (as slaves), and the registered file permissions. They have screwed everything up. The fixed file permissions and drive put back in original system.

  Œuvres self-retaining keys now. Do not, however, as my sticky keys doesn't have a link to configuration.

  Went back into recovery startup via the F8 key at startup. Now, when I run start recovery, it says that everything is going well and there is no problem.

  I have download the hotfix from article 977675 Microsoft, but I don't know how I can apply it without being able to get into windows. I would like to contact MS e-mail or chat support, but I can't get the product ID without being able to connect (frustrating talk).

  I would like to reinstall OS, but HP does not provide an installation disc with their systems (only a full restore partition). My system is backed up (with the exception of the Windows folder), but I really don't want to have to make a full recovery, as I have a lot of specialized programs and settings that would probably take me a week to re - install and re - set.

  Anyone have any new ideas?

  Hello

  Here's my usual BlackScreen convenience store, because it may be that you haven't tried
  or if you have access you might be able to come back and start some of them.

  ----------------------------------------------------------------------------------------------------------

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
  by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you do not have your system disks
  manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (to do the system restore there only to)
  being bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
  saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

  You can use another DVD that are not protected but you will need to copy you have the product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (type in a single line or copy / paste a line at a time and then press enter - type no parenthesis)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)
  
  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Black screen with white cursor at the end of the New Installation

  I try to perform a new installation of Windows Vista Home Premium (64 bit) on a Dell Inspiron 1545. The hard drive was completely wiped out and I don't have the original disks (I use a Vista CD from another computer Dell). Installation is proceeding normally up to the phase of "Complete installation" where it crashes for almost an hour and then goes to a black screen with a white cursor.

  I have tried all the following suggestions (found here and on other sites online):

  Reset the BIOS has no effect.

  By pressing SHIFT 5 times has no effect.

  CTRL + Alt + Delete has no effect.

  Rename to the event log file has no effect.

  Remove one of the memory modules if the computer has only 2 GB installed has no effect.

  Running CHKDSK finds no error, and has no effect.

  The attempt to start safe mode causes hang crcdisk.sys.

  Try a normal boot hangs at the screen loading w / loading scroll bar "stuttering".

  Startup Repair runs for hours with no results (I said to cancel after you let it run overnight only to find it still 'work' in the morning)

  Does anyone have suggestions more?

  Thanks in advance! : D

  Dell Media you are currently using may not have drivers appropriate for your PC.

  Contact Dell technical support (have your number of ready service if they ask for it) and ask for the "recovery media" to your specific model number. There may be a small fee involved.

  http://www.Dell.com/content/topics/global.aspx/services/en/dsc_home?c=us&l=en

  J W Stuart: http://www.pagestart.com

• Black screen with white cursor. Impossible to load Windows or even download a new copy

  I had Windows Vista on my computer and I got a virus. None of the antivirus working to clean the infected files and clips failed as well. So I decided to run repair system and it to halfway through, my office has crashed. I turned it our with the restoration of the vista disk and has no load. Then I attepmted to install a new copy of windows 7. It wouldn't load and I still get the black screen with the white cursor. I have therefore load Linux Mint and it seems that I can only have linuc on the computer. I deleted all lartitions because the partitions have been affected by the virus. Help, please. I need windows 7!

  Hello

  1. when exactly this problem?

  2 did you change on your computer?

  I suggest you remove any external devices.

  I also suggest you insert the DVD and try to install windows 7.

  I also suggest you to go BIOS and select CD/DVD boot as the option your priority and check.

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  I suggest you to follow the links and check out how to install windows 7.

  Installation and reinstallation of Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  Installation of Windows 7: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/installing-Windows-7-frequently-asked-questions

• Defective boot to a black screen with white cursor and DDDP errors.

  I have a Pavilion h8-1020, which began to show a black screen with a cursor flashing after the initial splash screen.

  I ran all the options except a complete reset utility mode.  I downloaded the Dell Diagnostics Deployment Package and booted from it.

  I ran the tests and got these errors

  4 c 00:0522 - system Interrupt controller or device has failed

  These all failed

  4600:021E - SMBIOS unidentified LM78A

  4600:021E - Fan1 SMBIOS

  4600:021E - SMBIOS chip fan 2

  I put an old HD and it starts to boot to the operating system while it recharges.  It is further than he gets with the original drive.

  Any thoughts would be appreciated.

  Thanks, BC.

  It's the Dell forum, so why you post questions on a computer HP here?

  The Dell diagnostics probably will work correctly with the HP hardware so that the results are meaningless.

  Ask your questions on the HP forum...

• How to print photos when the display screen is white? The image is missing in it.

  How to print photos when the display screen is blank?  It shows only a white screen empty when I select the photo and press on print.

  You click on a film image in the print module? And, I guess you don't have to go to the Print module, right?  Additionally, make sure that you have chosen to make a custom package.  If you chose the custom package you need to drag and drop images and organize them.

• setttings seem to have changed, now black background with white text. How do I change back? ___

  The settings seem to have changed (CAT sleeping on keyboard) wallpaper now black with white text and how the format appears on the screen has been altered.  How do I change back?

  The settings seem to have changed (CAT sleeping on keyboard) wallpaper now black with white text and how the format appears on the screen has been altered.  How do I change back?

  > How the format appears on the screen has been altered.
  I don't understand this part. Maybe you don't mind developed.

  Do a system restore. Pick a date before that happen as your restore point.
  Start button > Search box, type system restore > press the Enter key > uac prompt > click on choose a different restore point > next > select dates as your restore point, until the click > next > finish
  To sit and wait. The machine restarts when it's done.

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Black screen with white horizontal lines

  Every other time I start my computer from any State that it is in French - the screen is black or half black with 2 or 3 white lines which crosses the middle section horizontally. I run Windows Vista on my HP TouchSmart TX2 laptop. I spoke with HP who think it's a software issue. Any help would be great!

  First of all, you can install the latest video drivers from HP. If that solves your problem, then HP was right, and that's fine. However, if it is not then despite what HP you said this looks like a hardware problem with the video card or the laptop screen. MS - MVP - Elephant Boy computers - don't panic!

• Why Camera Raw displays a blue screen with white cross rather than the image I opened?

  Hello

  I'm having a problem with Adobe 9.0 Raw on my PC. When I open an image in Camera Raw by right-clicking since Adobe Bridge CC, it opens and displays a blue image marine with a white top cross where the image should appear. It happens with all jpeg images, I am trying to open. This problem started only for updating the software via Adobe Creative Cloud 3 days ago.

  Any help on this would be greatly appreciated!

  disable the GPU use in vintages camera interface

• iMac restart and does not recognize usb-keyboard... freezes black screen with white bar tape

  Does anyone know this problem?... reboot does not work, usb keyboard does not work and the screen freezes...

  

  What version of Mac OS X is installed on the computer?

• Display screen with Windows 7 problem

  Original title: Monitor problem

  Before I explain my problem.

  First of all, let me tell you a little about myself.  I'm 73 and I am a Novice in computers and do not consider myself an expert...  I have a degree in electronics with over 40 years of experience. I've built several computers for family and friends for years.  The problem, which I'll explain you completely confused me.

  I have a 24 "I-Inc monitor that I bought in 2008.  It has a nice clear image that never changed.  Best deal I've ever done in the monitors.  This monitor is connected to my computer main clocked i5 of operating system: Windows 7 Ultimate Professional Media Center 6.01.7601 Service Pack 1 (64-bit) fully updated.  Monitor is driven by video card NVIDIA GeForce 210

  Then, all of a sudden a few weeks ago the screen on the monitor began to go dark and back, dark and backward, dark and back.  The last dark anywhere among the second up to 30 seconds and the flashing would go one to five minutes.  Then stop and everything is fine.  So maybe some time later, I went to a different Web site it would start again.  Now, let me say clearly, there is nothing wrong with this monitor or my PC, which brings me to my next story.

  After fighting this monster of darkness for a few days, I decided to move it to what I call my computer of the workshop.  This computer has i3 cpu with NVIDIA GeForce 210 also in perfect condition.  This computer is also a system dual boot, AND this IS A SAME KEY PART.

  It has Ubuntu 14.04.3 md64 (my PC is 64bt) AND 10 for Windows.  This monitor is also connected with a HDMI cable and when I plugged it in this workshop cpu, I first booted to Ubuntu.  Everything was great for about a minute then the monster of darkness began her dance for about two minutes then stopped and the screen image was perfect.  I flipped around for a while, then the monster of darkness happens again.

  OK, so I decided to stop and start Windows 10.  You may not believe this, but with 10 Windows, IT IS No. MONSTER of DARKNESS... PERIOD!  Still, it is still connected to my cp Studio win 10, and I'm interested in what I type and the image is perfect.

  My conclusions: nothing wrong with the monitor that is always connected to the cp workshop and work perfect.

  All is well with all of my equipment in each system.  I use my monitor backup on my main system and all is well.

  Issues related to the:

  Why this monitor would work to win 10 and not in Win 7, where he worked once for years?

  Hello

  Please provide detailed information on this issue. I apologize for the inconvenience caused to you.

  Sometimes we can deal with this issue because of the incompatibility between the display with your operating system drivers. It is important to update the computer and drivers also requires the update. I understand that you have tried to solve the problem and it fixed with Windows 10. This could be due to the compatibility of the display adapter.

  In the future, if you have questions related to Windows, please do not hesitate to write us and we will be happy to help you.

  _______________

  Thank you best regards &,.

  Isha Soni

• Can I mirror to a wireless display screen with my Acer Aspire v3 - 771 G w/Windows 8.1?

  'Add a wireless display' does not appear in the project.

  bbrannon,

  Your system is not compatible WiDi, wireless itself card does not meet the criteria listed on theIntel site.

  With respect to the part number of the system, it's the first 10 chracters of serial number; just for future use, if you need to give it.