dlow data transfer speeds

Similar Questions

• What are the motherboard data transfer rate on a HP G60 - 243CL?

  I bought my laptop HP G60 - 243CL of Costco 3 years ago and continues to function perfectly. Since then I have maxed out the 320 Gig HARD drive. A few days ago, I transferred all my multimedia files of a terabyte of 1.5 external HDD. I also removed and uninstalled all the software that didn't come with the laptop pre-installed. I ran the Disk Cleaner to delete the temporary files... etc. I left pretty much the State of Out-Of-The-Box laptop... I also ran the Windows disk defragmentation application.  Although it has all updates from Windows Update. I doubt that the above mentioned is relevant to my question. The laptop came with two modules of RAM PC2-5300... a 1 Gig and 2 Gig. I replaced both with two sticks of modules/memory 2 GB PC2 - 6400. Other that this hardware upgrade, I've also upgraded to Windows 7 Ultimate edition 64-bit. Now, I am also considering upgrading to an SSD HARD drive. I have of course read/write speeds rise as SSD memory ability increases (depending on model)... for ex: there is a huge difference in the rate of data transfer speeds in a 32 Gig SSD compared to a 256 GB SSD. At least that's what I noticed. I want to install a Gig of CRUCIAL 512 or possibly a CRUCIAL 256 GB SSD. Read/write speeds are respectively of 500 MB/s and 260 MB/s, or 230 MB/sec and 190 MB/s (again, depending on the model). My question is noticed in the SUBJECT field. Can you please help me make a wise decision? I wish that more technical details as possible. Thanks... :-)

  This laptop is equipped with SATA I, which is 150Gbit/s. You will not reach the maximum speed of your SSD, but it will be much faster then your current old school disc spinner. An SSD will always exceed a normal HARD drive. In addition, you should see a bump in battery life as well.

  I hope this helps!
  Sean

• Slow transfer speed for USB 3.0 ports

  I have a USB 3.0 Seagate external hard drive connected directly to one of the USB ports 3.0 at the back of the computer with the cable that came with the drive. Whenever I turn it on, I get the message "this device can perform faster - this USB mass storage device can transfer information faster if you connect it to a USB 3.0 Super speed.

  I tested the speed of the hard drive and transferred on a file of 1.16 GB in 58 seconds of my drive "C".

  I also transferred the same file in the same place, for comparison, on a hard drive 10 years from an old computer which is now in a closed Chamber. This hard drive is also plugged into a USB 3.0 at the back of the computer with a USB 2.0 cable and the files had 57 seconds to cross.

  So that would mean that the Seagate drive does not work at the speed of USB 3.0.

  Can you please advise me as to how I can get the right speed for my USB 3.0 ports?

  DesF,

  You can check for a driver to chipset update for your system.

  Please keep in mind that it is a rotating disc and data transfer speeds do not match the theoretical bus speed. Certainly not the often claimed "ten times faster than USB 2.0! In addition, there a 5900 RPM disk, so a little slower there also.

  A tweak, you can try is to make sure that drive policy properties tab is set for best performance.

• can xp support a flow rate of 50 MB/s - is there a limit to the speed of data transfer, it can support?

  can xp support a flow rate of 50 MB/s - is there a limit to the speed of data transfer, it can support?

  I have a 50 MB/s via fiber optic connection and it works fine under XP.

  Steve

• How do you speed up 5.8 to 7.2 disk data transfer rate?

  In my rateing of expieriance of windows, all my scores void are 7.2 and 7.5, except my disk data transfer rate is 5.8. I would like to know what I do for all my partitions of sup of 7.2 to 7.5. Could someone tell me the secret to do that? Your answers will be greatly appreciated!

  Thank you.

  Fred

  On Thu, 20 Sep 2012 17:50:11 + 0000, FredKoerner wrote:

  In my rateing of expieriance of windows, all my scores void are 7.2 and 7.5, except my disk data transfer rate is 5.8. I would like to know what I do for all my partitions of sup of 7.2 to 7.5. Could someone tell me the secret to do that? Your answers will be greatly appreciated!

  Replace your hard drive by a faster, for example with an SSD.

  But in my opinion, you should ignore completely all windows
  Results of the experiment. They are just numbers; they are very
  mislead and I wish that Microsoft has never included in
  Windows. You must judge for yourself what your performance is,
  and take steps to improve performance (purchase of quality components)
  only if you find that your performance is unacceptable.
  Ken Blake, Microsoft MVP

• Slow data transfer between computer and HP Laser Jet 1320n

  I recently bought a laptop with windows 8.1 and successfully connected to 1320n times via LAN and wireless networks. Problem is when I try to print .pdf files, data transfer from my computer to the printer seems very slow and that's why it takes several minutes to print 10 pages. On the print window of my system, it tells me the data to transfer a file from pdf page 14 are about 75 MB.

  My questions are:

  1-is-normal this size of data?

  2. What can I do to increase the transfer speed?

  Thank you in advance.

  H.A.

  Thank you very much for the reply.

  I hae has solved the problem by installing the drivers that are on the product page (I was using the Windows drivers when I had the problem). Everything works as it should now.

• Sudden slow data transfer

  Hello

  I am happily using my 3 GB Time Capsule for the last 18 months with no problems. I use it almost exclusively as data storage for my Plex server. I use it wirelessly to my Macbook Pro 2014, in the same room.

  Yesterday, without change to explain it, it has become very slow to transfer files to it.

  

  I am at a loss, as most of the solutions I looked for people who have had problems of speed from the beginning, mine was a sudden appearance.

  Speeds do not seem to affect my streaming quality that I can still watch a 1080 p 5 gb + video file without stuttering or offset. The problem is isolated to the data transfer it seems.

  Any suggestions where to start?

  I use it almost exclusively as data storage for my Plex server. I use it wirelessly to my Macbook Pro 2014, in the same room.

  The plex server is connected by ethernet?

  Speeds do not seem to affect my streaming quality that I can still watch a 1080 p 5 gb + video file without stuttering or offset.

  It would be difficult to know if streaming is more... and more through your Macbook wireless...

  So I just need to know what is connected by ethernet and what is connected by wireless.

  Wireless is seriously affected by a number of things. So I guess that the first test is to connect the laptop to the TC by ethernet and make sure that it works very well. If your ethernet Mac buy a crush on ethernet card... a necessity, in my humble OPINION... as trying to fix wireless more wireless resembles sawing off the branch that which you are sitting.

  If you can determine the network of the question... Then we can do the simple things...

  Run the diagnostics wireless...

  Just restart the entire network, which I am assuming that you tried but did not mention.

  Simultaneous copy of a file on the hard drive while also streaming can also be stressing the TC... If the tests should be carried out without any other use of disk passes.

• Satellite L505-144 - flash memory transfer speed is very slow 1.45 Mbps

  Hello

  I have a Satellite L505-144 and installed the system Win 7 64-bit *.
  The problem is when I move or copy DATA using Flash memory, transfer speed is very slow 1.45 MB/second and I try the same memory Flash on another PC its work too quickly it move 22 MB per second

  What is the problem?

  Hello

  What is the status of the SATA mode in the BIOS?
  It must be set to AHCI.
  If it s set to compatible, then the SATA benefits can not be used
  Check it!

• Satellite A60 - very slow USB transfer speed

  Hello

  I have a Satellite A60 with XP Home and the USB transfer speed is very very low. Is 2.0, but it is not working properly, because it takes about 30 minutes to copy the data from 1 GB on a USB 2.0 drive externally.

  I tried my USB drives on another computer and work quickly and well, so it is probably just a problem of drivers, but can't find them on the web from Toshiba to reinstall them. I heard that it is a common problem after installation of XP Service Pack 2, but I didn't do anything, I use the operating system as it came when I bought the laptop (with XP Home SP2 preinstalled original), I do not change any configuration or install drivers that can affect to the USB controllers and it has always been so slow.

  Could someone help? I tried to reinstall the drivers from Toshiba, but I think that there are not more special just for the USB, what should I update then? I need to improve the transfer speed of USB data for professional purposes, because I can't lose so given at the time of the transfer, please please please help!

  PS: Sorry for my terrible English, but it is there no Toshiba forums on my tongue: P

  Hello

  USB drivers are part of the operating system and you are unable to download the USB drivers separately.
  In my view, it is really not necessary to reinstall the USB drivers because the USB HDD is recognized correctly and it works.

  USB 2.0 transfer speed 480 Mbps supports and if any didn't error message then the USB ports running at full speed.

  For more details, please see this page of Microsoft;
  http://www.Microsoft.com/windowsxp/using/networking/learnmore/jones_02august05.mspx

  Last but not least I would recommend to update the XP to the last State. I mean that you need to install all of the available patches and fixes.

  Good bye

• Is my 2011 macbook pro the neck of the bottle in my LAN slow transfer speed?

  Hello

  I have a macbook pro 2011 and I recently bought a buffalo LS 520 NAS, but when you try to transfer data through my wifi network that speeds are painfully slowly.

  WiFi area speeds as follows:

  Upload: 0,6906480 MB/s

  DOWNLOAD: 6,2196480 Mbit/s

  And here's the transfer speeds for the macbook pro on the NAS directly connected via ethernet

  Upload: 62,689 Mbps

  Download: 796.3651920

  I have a Sky Home Hub router 2013 (144Mbps and 2.4 GHz)

  I think that the might of bottleneck the NIC in my macbook pro, but I am not sure. Even if that were the case, the speeds above seem very slow. I am planning to buy a new router to see if that improves things, but will it be useless if the speed is dictated by my macbook?

  You need a router more...

  Especially if you want to use wifi for transferring files you need in 5 GHz... so I don't spend much time worrying about this.

  Get a new router... you can plug into the hub of the sky... It should be wireless AC so it may be a new extreme Apple or it can be a dozen different brands... all that is readily available and reasonable price... but I highly recommend types AC1900 like Netgear R7000, Asus RT-AC68U or C9 of TP-Link.

  Once you have plugged it in the WAP configuration / Skyhub mode (bridge on the extreme) we can establish if there are still questions what is happening.

  Your 10 x difference in upload and download speed makes no sense. Which affects both wireless and ethernet. The difference in speed of reading and writing on a NAS is double at most.

  But I do not pretend do you a test, ethernet jack directly to the Buffalo and implemented with the static IP as well as your laptop... and then try it... view results... because if these figures are also very strange, then there is a problem with the buffalo...

  It is very important that you her mount smb in El Capitan... the question is something you need to post in the area of the BONE...

• How to calculate the rate of data transfer if I know that the total number of samples/s?

  I'm looking to set a PXI system for measurement of County at high speed, routes, while that controlled remotely via MXI - 4.  How can I be sure that the controller is capable of rapid data transfer quite seen the number of channels and frequencies of sampling provided?

  I think I figured this out, but maybe someone can save me.  For the task at hand, I will have a PXI-4496 and four PXI - 6143 s all 32768 samples/s sampling.  4496 is 24-bit, and 6143 is 16-bit.  Thus,.

  bits of samples/s/channel x 24 16 channels x 32768/8 = 1 048 576 bytes / s

  +

  32 x 32768 samples/s/channel x 16 bits/8 channels = 2,097152 bytes/sec

  =

  3 145 728 bytes/s, or exactly 3 MB/s.

• Data transfer NI653x

  Hello

  We used the NI6534 card to transfer data from our system in a PC. He works on traditional pilot and DAQmx. We use handshanking calendar for data transfer. Recently, we want to increase the speed of data transfer and need to change the "timing" of the handshake to sample clock calendar (model IO in traditional version). We got it working using the traditional driver, but not by DAQmx. I always get an error code when you try to start the data acquisition. Code error-89129 - Terminal is not valid for the device. Here is C code to configure and start the map:

  DAQmxCreateTask("",&m_taskHandle);
  DAQmxCreateDIChan (m_taskHandle, "Dev3/port0_32", "", DAQmx_Val_ChanForAllLines);
  m_numofSampletoRead = 2000000;

  continue to generate samples up to the stop.
  bRet = DAQmxErrChk (DAQmxCfgSampClkTiming(m_taskHandle,"Dev3/PFI2",20000,DAQmx_Val_Falling,DAQmx_Val_ContSamps,m_numofSampletoRead));
  specify the size of the buffer
  bRet & = DAQmxErrChk (DAQmxCfgInputBuffer (m_taskHandle, BUFFER_SIZE));

  Once he went to configuration and once called the DAQmxStopTask (m_taskHandle) function, he returned this error code I mentioned above.

  With respect to the traditional version, I just added a call to the function below and it worked fine.

  If (!) () status = DIG_Block_PG_Config (m_deviceNumber,
  m_group,
  1, / * enable the generation of model using REQ edge lock * /.
  1, / * REQ - REQ external source * /.
  -3, / * time - base 50ns, it is an internal clock * /.
  1, / * interval REQ * /.
  ((((i16) 0))) / * turn on or off the switch * /.

  Can you help me how to make it work with DAQmx? Thank you.

  Thank you, James. The example of aid. The function I called:

  DAQmxErrChk (DAQmxCfgSampClkTiming (taskHandle, "/ Dev3/PFI2", 10000.0, DAQmx_Val_Rising, DAQmx_Val_ContSamps, 1000));

  I missed the first slash highlighted in RED.  I've was allowed past this function call but got stuck at the next function call, DAQmxErrChk (DAQmxStartTask (taskHandle)), that me cheated.

  Thanks again for your help.

• USB-6218 for PC transfer speed

  Hi guys,.

  I hope to be able to taste 10 channels 10 Hz for about 1 hour, in Labview 8, on a relatively new core dual desktop PC.

  First, I tried an Agilent34970a and concluded that, even if she can continuously scan quickly enough, GPIB in Labview transfer speed was too slow and the PC could not follow.

  So I intend to implement a continuous sweep on a USB-6218 and then read it via USB, time-stamped data in Labview.

  After reading about OR "sample streaming usb", my question is: approximately how long will be the transfer of data via USB? I'll be able to transfer time-stamped 10 channels at 10 Hz continuously in Labview, and still have cycles left processor above for other duties such as writing to the file .VI and update the screen.

  The reason for which I am aiming for USB and no PCI/PXI is because I am concerned about the interference of the computer that affect my signals.  I read only analog voltages in the range of +-10V.

  Thank you for your understanding.

  You can acquire and store at rates of several orders of magnitude higher than 10 Hz. A good way to make sure you can follow has a producer/consumer architecture so that the file writes are made in a separate loop. Backup to the binary is also much faster than backing up to the text. Thus, the design of the program is important as well as the material you use.

• Mini Mac server - attachment of external hard drives file transfer speed

  Hi guys!

  I wanted to increase the speed and storage capacity to transfer to my Mac mini file, so I bought a box of external hard drives. The one I bought is: http://www.icydock.com/goods.php?id=219

  Built-in the Mac mini hard drives transfer the file to 60 MB/s (writing and reading) and I wanted to get better speed of file transfer, so I bought an SSD that is going to be inside with an another HARD drive of 3 TB for archiving my files. The housing is connected by USB3.0 (5 Gb/s) for the Mac mini.

  [SSD-> files I opened every day] - speed around 550 MB/s write and 500 MB/sec in reading

  [HDD-> Archives, files that I have does not open very often] - speed around 150 MB/s write and 150 MB/sec in reading

  So I did some benchmarks on my new Setup, and the speed is not really what I expected. Transfer of file max speed I have achieved is about 100 MB/sec in writing on the external SSD plugged into the mac mini. This transfer has been filed since an iMac 21 "2011 with an SSD (with almost the same speed read/write than the box) so it's quite disappointing.

  It is possible that the Mac has a 'file transfer speed limit' is somewhere? Or whatever else that could affect that?

  More information on my setup:

  Mac Mini server 2012 - 2 TB RAID 1 - Mac OSX 10.9.5

  iMac 21 "2011 - Crucial SSD 275 Gb - Mac OSX 10.9.4

  IcyDock external enclosure - 4 bays, USB3 5 Gb/s

  -Red WD HDD 3To

  -Crucial SSD 1 TB

  Together internal Gigabit Ethernet network

  Thank you!

  Was perhaps Spotlight indexing external at the same time, the test has been done?

• Data transfer?

  Is to connect your iPad to a computer to transfer data to your iPad another way of data transfer such as an OTG device as a micro SD card?

  Thank you

  Depending on the data type and the application that you use to access this data, you may be able to save to DropBox or dedicated application servers back up (if it is a characteristic of soft offers).

  SanDisk made a series of key USB Wifi active. However, due to the nature in iOS sandbox, there are many limits on what you can switch to the player. Everything happens through the application owner.