DMA between host and target FPGA is not supported for this remote system.

Similar Questions

• Error "the dynamic disks are not supported by this operating system." what configuration Raid 0 (striped) readers.

  I have my operating system installed on a single disc, and I bought two additional discs I want to implement in a Raid 0 configuration. I'm going to administrative tools > computer management > disk management > right-click on a single disc and select the new striped volume > add the second drive and fill the dialog box until I get to the part where the formatting is supposed to start. Then I am stopped by an error that says "the dynamic disks are not supported on this operating system."

  Who says that hard drives, I bought are not compatible with vista interlacing or it says that vista can not the striped disks. What is the problem?

  You need to configure raid 0 before installation of win, you cannot "convert" s simple drive to the part of a matrix of blocks.

  In general this is not a good idea to use software raid, too a overload the CPU. If you want to raid, invest in a dedicated hardware raid card, which for a decent cost probably more than your motherboard

• You try to create VHDX or another format not supported for this version of the server

  Hello

  I have a problem with vWorkSpace do not load VM and I really hope that someone here might be able to add comments. We run vWorkSpace v8.5 on a box of windows server 2012 and v6.1 Hyper-V on Windows Server 2008.

  After running then changing the main image, I've updated the image of our cloud. Once the update of the virtual machine would not load, giving the below error

  End of the action (create) (failed to create. CreateVM: Unable to create the virtual machine of provided information. : CreateVhdxDisk: try to create VHDX or other format not supported for this version of the server. Path to the virtual disk: .avhd - call stacks - to Quest.vWorkspace.VirtualCore.HyperV.HvVmService.CreateVM (VmCreateData createData, String domainNameIP)
  at HypervLocalExecutor.HvCreateVM (string strUser, strPwd, VmCreateData createData, String strDomainNameIP, VmResult String & result)
  to CHyperVClone.doClone (basic_string<>\,std::allocator > * nsHostName, basic_string<>\,std::allocator > * nsUsername, basic_string<>\,std::allocator > * nsPasswd, VmDefData * vmData, basic_string<>\,std::allocator > * strDomainIPaddress, NewVmInfo * newVmInfo)-> Quest.vWorkspace.VirtualCore.HyperV.Server2008R2.CreateVhdxDisk (String parentDiskPath, String diskPath)
  at Quest.vWorkspace.VirtualCore.HyperV.Server2008R2.CreateDiskForVM (vmMgmntObj, String vmPath, VmCreateData ManagementObject & vmData, String & vhdPath)
  at Quest.vWorkspace.VirtualCore.HyperV.Server2008R2.CreateVirtualMachine (VmCreateData vmData, String domainNameIP)
  at Quest.vWorkspace.VirtualCore.HyperV.HvVmService.CreateVM (VmCreateData createData, String domainNameIP))...
  5 March 2015 15:54:15 - 1392:8580511090155201372 - caught error: Stack Trace and stack Exception below:
  at Quest.vWorkspace.VirtualCore.HyperV.Server2008R2.CreateVhdxDisk (String parentDiskPath, String diskPath)
  at Quest.vWorkspace.VirtualCore.HyperV.Server2008R2.CreateDiskForVM (vmMgmntObj, String vmPath, VmCreateData ManagementObject & vmData, String & vhdPath)
  at Quest.vWorkspace.VirtualCore.HyperV.Server2008R2.CreateVirtualMachine (VmCreateData vmData, String domainNameIP)
  at Quest.vWorkspace.VirtualCore.HyperV.HvVmService.CreateVM (VmCreateData createData, String domainNameIP)

  We believe that it is somehow to do with Hyper-V under Windows 2008 and vWorkSpace running on Windows 2012 - the VHDX format is not supported by the version of Hyper-V server. A glance online confirms this. So my question is, how update the master image changed the format VHD vWorkSpace wants to use and is there a way to assign vWorkSpace don't know this format?

  I have widely in search of a solution to this line and not found anything it either, nor there seems a clear way in the vWorkSpace console to change that.

  Thank you

  Hello

  I suspect that you have created a snapshot on your model.  It is not supported, if you delete the snapshot so that the .avhd is merged to the vhd/vhdx and update the model in vWorkspace again.  If this does not work, you will need to delete the model of vWorkspace and then re-import.

  Concerning

  Paul

• VMware Tools: VMware Tools don't is not supported on this operating system

  On one of our server VMware Server 2 (Version 2.0.2 Build 203138 (Linux version)), I made a new standard of Windows 2008 edt. Comments of 32 - bits. When I try to install the vmware tools, I get the following message: "VMware Tools is not supported on this operating system. When I check the setting guestos vmx file indicates "longhorn." Someone knows how to fix this?

  You can always get the windows.iso manually and see if you can install the tools.

  First, make a snapshot!

  ___________________________________

  VMX-settings- Workstation FAQ -[MOA-liveCD | http://sanbarrow.com/moa241.html]- VM-infirmary

• Your browser is not supported for this program. This program is expected to be launched above IE4 version!

  The provider's Web site will not reflect orders/quotes...
  We get this message
  "Your browser is not supported for this program.
  This program is expected to be launched above IE4 version! »

  URL of affected sites

  http://

  To work around this problem, you can also try using the User Agent Switcher add-on to give the impression that you are using IE on the site.

  You can contact the site owner to inform them of their poor support for Firefox.

  Alternatively, you can report a broken help site.

• Cannot convert a computer unalloacted on a new space, dynamic disks are not supported by this operating system or the configuration of the server. Dynamic disks are not supported on Clusters.

  I have 179 GB of a 50 GB hard disk on a new computer allowed. Try to make a new Simple Volume I get following error "the dynamic disks are not supported by this operating system or the configuration of the server. Dynamic disks are not supported on Clusters", please suggest what to do, i run Windows 7 Home basic.

  I have 179 GB of a 50 GB hard disk on a new computer allowed. Try to make a new Simple Volume I get following error "the dynamic disks are not supported by this operating system or the configuration of the server. Dynamic disks are not supported on Clusters", please suggest what to do, i run Windows 7 Home basic.

  Need additional details as
  Is it a laptop or a pc?
  Have you coveted your dynamic disk basic disk?
  What the structure of partition on your computer?

  recover with these details...

• PC and Windows settings store will not open in windows 8 after refreshing (safe mode, boot clean and sfc/scannow do not work for this)

  Don't forget to support this issue to get a faster response! : D

  A few weeks ago, I was using my computer and it worked very well. Once I got home I turned it on, but it does not turn. After trying several times and get only a black screen I finally got an answer, my computer was looking for solutions, and finally I decided to update it. Once I did, everything seemed to work, but as he was warned many of my apps have been removed. Once I tried to download office, a message appeared and the dignosi said that "a problem is preventing the troubleshooting tool to start. After this, I restarted my PC, but the problem persisted. Then I tried to open the app store and it did not open at all it just poped to the top of the icon of gree. With this problem and no solution, I scanned my computer but nothing. Then I looked on the internet, it seemed to me that many had my problem. Then I tried what more said and noticed that something that I could not even do is run at the prompt as an administrator. It took a lot of my possibilities, and the problem of not being able to download anything at all do not let me even try firefox or install any kind of service. To resolve this problem, I have internet and with the help of my brother, I could do my account manager and perform the sfc can. After that he told me that I had nothing wrong. The next thing I did was try to run "chkdsk/r", after that I could download and install things over the internet so I did a update and installed everything I could. The only problem was that the store and the laptop settings cannot yet open and I tried every utility in the internet troubleshooting and recommendations, but nothing works, I can't even change my background of my photos folder. Please help: c

  Hi Francisco,.

  You can check this link for now.

  WIN8: App: modern: Apps do not start if the default registry permissions or the modified file:
  http://support.Microsoft.com/kb/2798317/en-us

  Please return to the State of the question.

• Message problem "version of NI-VISA, which is not supported on this operating system has been detected... »

  Good night!

  Recently, I want to install the driver NI-VISA on my PC because I needed for arduino. I checked the versions available for my operating system (Windows 8 not 8.1) I tried with 5.01, 5.2, 5.3, but in all cases send me the same message, I look in programs and features in the software section OR for uninstall (if I have) the older version of VISA, but I have found that I Don t have any version. Also I Don t have any version of the software NOR-488 or something like that on my PC (I Don t know if I have to install for installation of NI-VISA) and send me the same message again, I Don t know what to do, if uninstall labview 2010 or get a new version or uninstall 2010 and install NI-VISA and then install LV Please help me...

  Like I said I have Windows 8, I7 Proccesor, LabView 2010 installed with this product: Circuit design, lego mindstorms, engine performance, OR measurement and automation,-configuration system, TDM Excel and update service (all this United Nations programs and features in the software section of OR).

  Best regards and thanks!

  
  

• the size of your hard drive is not supported for this process. Please use a hard drive at least GB in size

  Whenever I try to use my restore disks of backup with the image of the system when I bought my Dell 8300 desktop computer I get this error message (your hard drive is not taken in charge for this process. Please use a hard drive at least GB in size.

  My computer crashed went to blue screen that wouldn't everything now I hear 4 beeps, finally I managed to do start on. I already ran the long diagnoses everything was fine.

  Here's my problem. I changed the Sata AHCI RAID mode I could create a partition then my Windows 7 downloaded CD Windows 7... my CD of drivers dell drivers, but now I'm unable to use my system restore CD to restore like I always do when I have a problem. When I changed the sata mode to AHIC on load it says (lack of operating system)

  I'm not very technical, so if someone can show me step by step on what I should do or give me a call [Admin Note: personal information removed] I would appreciate it a lot. I've added a few pictures as well

  

  

  Large. I am pleased that my DBAN guide has helped you.

  Now that you are on the factory settings, I advise Dell DataSafe Local Backup uninstall and upgrade to the latest version of Dell backup and restoration which has many bugs/improvements, including the ability to restore to another hard drive which is useful in case the hard disk fails in the future or you decide to upgrade later to an SSD. The XPS 8300 running perfectly with a SSD, I have mine put in place with one. Then you can create a Rescue Disk (external hard drive Bootable) or Backup factory (Bootable USB Flash Drive) that will be promoted the recovery compared to the facts media with Dell DataSafe Local Backup. See here for more details:

  http://dellwindowsreinstallationguide.com/Dell-backup-and-recovery/

  Note This is not a UEFI BIOS (he missed just out on the passage to the UEFI) but may start from an external hard drive.

• When will Windows 7 be compatible with Internet access? When I go through access of __web it says "not supported on this operating system" __I just bought 2 new P 7 computers that cannot access the other computers on my network. __

  See above

  ·                                 This is the Forum for Windows Update .

  For questions of Windows 7, here is a link to a list of the Windows 7 Forums:

  http://social.answers.Microsoft.com/forums/en-us/w7network/threads

  Windows 7 Networking Forum at the link above.

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 forum for questions on windows 7.

  All Windows 7 issues (other than Windows 7 update issues) should be directed to the it.

  See you soon.

  Mick Murphy - Microsoft partner

• Alert target Version does not support

  

  I have a form which should work with Acrobat Adobe Version 8 and higher.  My version of the target is set at 8.0 and later.

  I have two warning messages: target version does not support the validationState event and target version does not support the postSubmit event.

  When I first open the because I get the error message of the screenshot above.  When you look at events with scripts there not a script associated with both of these.  The error is associtaed with the 6 key, but I have a script for when you click to add instances.

  Is there anyway to remove these elements that give the error?  And is there a way to go to the line 9419?

  Thank you

  You can send the form to [email protected] and I'll have a look when I get the chance.

  Paul

• Do not click on in the VM and can not move files between hosts and virtual

  Do not click on in the VM and can not move files between hosts and virtual

  Home - Windows XP x 64 Edition

  Virtual - Windows 2003 Web Edition

  -vmware.log

  ...

  sept 23 14:10:17.875: mks | Setting size 40 pile of thread to 1048576.
  sept 23 14:10:17.875: mks | Adjusting size of 41 of the stack of the thread to 1048576.
  sept 23 14:10:17.890: mks | USBGW: Writing referee op: 13 len:36
  sept 23 14:10:21.718: vcpu-0 | Unified TOOLS loop capacity requested by 'box to tools-MDN; now sending via the TECO
  sept 23 14:10:21.718: vcpu-0 | GuestRpc: Channel 7, toolbox-MDN app reviews.
  sept 23 14:10:21.718: vmx | DnDRegisterRpc: Rpc of DND already set to 1
  sept 23 14:10:21.718: vmx | CopyPasteRegisterRpc: already the value 1
  sept 23 14:10:21.890: vcpu-0 | VMXVmdb_LoadRawConfig: Loading of raw configuration
  sept 23 14:10:22.000: vmx | DnDRegisterRpc: Rpc of DND already set to 1
  sept 23 14:10:22.000: vmx | CopyPasteRegisterRpc: already the value 1
  sept 23 14:10:23.750: mks | USBGW: Writing referee op: 13 len:36
  sept 23 14:10:30.703: mks | Setting size 40 pile of thread to 1048576.
  sept 23 14:10:30.718: mks | Adjusting size of 41 of the stack of the thread to 1048576.

  ...

  Any ideas?

  Thank you

  If your license key allows, update your VMware Workstation version 7.1.4

  Otherwise, at least upgrade your VMware Workstation to version 7.0.1

  In the menu bar, help-> Check for Updates on the Web.

• Cannot drag-and - drop between host and guest

  12 workstation

  Host = 10 Pro x 64 Windows

  Comments = 10 Pro x 64 Windows

  Everything is entirely up to date, etc. on a Z87 PC chipset.

  I can copy and paste. I can drag-and - drop comments to the host.

  I can't drag-and - drop between host and guest! lol I just get that bar circle icon.

  I'm totally stumped! I tried a myriad of common things...uninstalled/reinstalled VMWARE, then Tools, then even tried to create new guests. I do not have eccentric tweaks or customizations. It is a desktop PC that I use for a laboratory test and my business. I have no other problems in addition to this. Yet, on my other system, essentially a nearly identical configuration, I don't have this problem.

  Any suggestions?

  SOLUTION FOUND!

  The problem boils down to a matter of RUN AS ADMIN. On the HOST problem, it has been set to RUN as administrator. I've not done this! He has just installed that way automatically. Once I stopped that and it ran normally, all was well again. Read below for more details.

  I have two virtual HOST machine configurations almost identical - we'll we'll call HOST 1 and HOST 2. HOST 2 works perfectly without a problem. Drag and drop, to navigate to drives mapped to access NAS stored VMs, etc...

  I began to compare what was similar vs. different between the two. On HOST 1 (problem child even as I could slide properly - drop on), I noticed that I could not navigate to my NAS location where some virtual machines are stored. In the left navigation panel, the mapped drives would appear as drive letters with question marks next to them as you can see in the image below.

  

  I deleted the mapped drives then mapped them still fresh, did an other CLEAN uninstall VMWARE WS PRO 12. I combed the registry, records and checked for devices hidden in Device Manager. Clean as a whistle! I reinstalled 12 Workstation and returned the problem! I could yet drag-and - drop properly or navigate to mapped drives. Then I noticed the HOST 2 that he was not being RUN as administrator. Really? So, I removed this parameter and TA DA! Everything started to work properly. I don't know if it's a bug, or knowledge common to others but for me it was new. I don't know why, by default, when installing 1 HOST went down VMWARE to run as administrator, but it was.

  Bottom line - do not run VMWARE as an administrator.

• It is only five years, since I bought the MBP. And "not Stopped Apple hardware support for this products just because they sell it?

  Hello

  I have a 17-inch, mid 2010 MBP.

  The internal DVD drive is broken.

  I contacted the Support of Apple. And sheet metal tech me that "Apple does not support any material for the MBP.» And what I can do is to get an "external DVD drive.

  It is only five years, since I bought the MBP. And "not Stopped Apple hardware support for this products just because they sell it?

  Ed

  < re-titled by host >

  If your computer is on this list it is no longer supported: Vintage and obsolete products - Apple Support

• RMAN-06429: TARGET database is not compatible with this version of RMAN

  He Hi,.
  How can I solve this problem. How I will modernize the Rman. My database of production details are below
  ----------------------------------------------------------------
  Oracle Database 10g Enterprise Edition Release 10.2.0.1.0 - Prod
  PL/SQL Release 10.2.0.1.0 - Production
  CORE 10.2.0.1.0 Production
  AMT for 32-bit Windows: Version 10.2.0.1.0 - Production
  NLSRTL Version 10.2.0.1.0 - Production
  
  while I'm setting up rman I get below error. Please help me.
  
  C:\Documents and Settings\vj.dcruz > target rman / catalog rman01/rman01@upp
  
  Recovery Manager: release 11.2.0.1.0 - Production Wed Sep 14 08:18:02 2011
  
  Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
  
  Recovery Manager incompatible with the TARGET database: required 8.0.4.0 to 10.2.0.0 RMAN
  RMAN-00571: ===========================================================
  RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
  RMAN-00571: ===========================================================
  RMAN-00554: initialization of the package manager internal collection failed
  RMAN-06429: TARGET database is not compatible with this version of RMAN
  
  Rgds,
  John

  Johnvd wrote:
  Hi Hemant,

  I do the same database connection 10.2.0.0 thing and configure the rman but while connect target its saying that my Recovery Manager: version 11.2.0.1.0 - Production the sea Sep 14 09:04:59 2011

  How its happens is there anywhere that I need to change the path.

  Kind regards
  John

  John, you should use the binary RMAN that is located in the bin folder of Oracle database (IE u01/oracle/product/10.2/db1/bin). You should not use "rman which comes with Oracle 11g client".

  If you are using windows, run the following commands at the command prompt, and then copy / paste the output:

  echo % 5ORACLE_HOME
  echo %path%

  If you use unix, run the following commands in the terminal and then copy / paste the output:

  echo $ORACLE_HOME
  echo $PATH

  Concerning

  Grosbois