DMVPN with based remote access VPN client

Hi all

We DMVPN deployed to connect to our remote location now I want to configure the vpn remote access also with DMVPN tunnel so if somehow our DMVPN tunnel goes down we can connect to the router through vpn remote access client based around... I want experts to do the light on it is it possible or what are the technical challenges that I have to face in this regard.

Thank you

Salman Jamshed

Hello Salman,

It's 100% possible, there is no harm in having them both up on your router.

In fact, as you have said that it will provide an extra layer of redundancy if by chance the DMVPN tunnel breaks down.

That being said, you can go ahead and do it is a movement course

Julio

Tags: Cisco Security

Similar Questions

Configure ASA5055 as a remote access VPN client

Hello world

I'm trying to configure a 5505 as a remote access VPN client. I have several old hubs VPN 3002, but in the new sites I'll use a 5505 instead of these 3002.

I think that the configuration is very simple. I have the IP address of the peer (remote server), I know it is an IPsec tunnel without certificate and I have passwords and user name and group.

How can I translate this configuration for an ASA5505? I have attached a screenshot.

Here ya go:

http://www.Cisco.com/en/us/docs/security/ASA/asa83/configuration/guide/ezvpn505.html

Federico.

How to prohibit remote access vpn client to use the local DNS server

Hello

I'm on ASA5505 remote access vpn configuration.

Everything works fine so far, except when the client got connected, he always used the local DNS server provided by the ISP. How can I force the customer to use the DNS server configured on ASA?

Thank you.

Kind regards

The command "Activate dns split-tunnel-all" is supported only on SSL VPN and VPN IKEv2. Since you're using IKEv1, this command is not supported.

Here's the order reference:

http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/S8.html#wp1533793

You configure no split tunnel? If you are, then you need to configure "tunnelall" split tunnel policy, and that will force the dns resolution and everything else through the VPN tunnel.

Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

Thank you

interface Ethernet0/0

Speed 100

full duplex

nameif outside

security-level 0

IP x.x.x.x 255.255.255.240

!

interface Ethernet0/1

Speed 100

full duplex

nameif inside

security-level 100

IP 10.88.10.254 255.255.255.0

!

interface Management0/0

Shutdown

nameif management

security-level 0

no ip address

!

permit same-security-traffic inter-interface

permit same-security-traffic intra-interface

network of the PAT_to_Outside_ClassA object

10.88.0.0 subnet 255.255.0.0

network of the PAT_to_Outside_ClassB object

subnet 172.16.0.0 255.240.0.0

network of the PAT_to_Outside_ClassC object

Subnet 192.168.0.0 255.255.240.0

network of the LocalNetwork object

10.88.0.0 subnet 255.255.0.0

network of the RemoteNetwork1 object

Subnet 192.168.0.0 255.255.0.0

network of the RemoteNetwork2 object

172.16.10.0 subnet 255.255.255.0

network of the RemoteNetwork3 object

10.86.0.0 subnet 255.255.0.0

network of the RemoteNetwork4 object

10.250.1.0 subnet 255.255.255.0

network of the NatExempt object

10.88.10.0 subnet 255.255.255.0

the Site_to_SiteVPN1 object-group network

object-network 192.168.4.0 255.255.254.0

object-network 172.16.10.0 255.255.255.0

object-network 10.0.0.0 255.0.0.0

outside_access_in deny ip extended access list a whole

inside_access_in of access allowed any ip an extended list

11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

NAT static NatExempt NatExempt of the source (indoor, outdoor)

NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

!

network of the PAT_to_Outside_ClassA object

NAT dynamic interface (indoor, outdoor)

network of the PAT_to_Outside_ClassB object

NAT dynamic interface (indoor, outdoor)

network of the PAT_to_Outside_ClassC object

NAT dynamic interface (indoor, outdoor)

Access-group outside_access_in in interface outside

inside_access_in access to the interface inside group

Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

dynamic-access-policy-registration DfltAccessPolicy

Sysopt connection timewait

Service resetoutside

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto-map dynamic dynmap 10 set pfs

Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

Crypto-map dynamic dynmap 10 the value reverse-road

card crypto mymap 1 match address outside_1_cryptomap

card crypto mymap 1 set counterpart x.x.x.x

card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

card crypto mymap 86400 seconds, 1 lifetime of security association set

map mymap 1 set security-association life crypto kilobytes 4608000

map mymap 100-isakmp ipsec crypto dynamic dynmap

mymap outside crypto map interface

crypto isakmp identity address

Crypto isakmp nat-traversal 30

Crypto ikev1 allow outside

IKEv1 crypto ipsec-over-tcp port 10000

IKEv1 crypto policy 5

preshared authentication

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 10

preshared authentication

3des encryption

sha hash

Group 1

life 86400

IKEv1 crypto policy 50

preshared authentication

the Encryption

md5 hash

Group 2

life 86400

IKEv1 crypto policy 60

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 70

preshared authentication

aes-256 encryption

sha hash

Group 1

life 86400

IKEv1 crypto policy 90

preshared authentication

aes encryption

sha hash

Group 2

life 86400

Telnet timeout 5

Console timeout 0

management-access inside

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal BACKDOORVPN group policy

BACKDOORVPN group policy attributes

value of VPN-filter 11

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelall

BH.UK value by default-field

type tunnel-group BACKDOORVPN remote access

attributes global-tunnel-group BACKDOORVPN

address pool Admin_Pool

Group Policy - by default-BACKDOORVPN

IPSec-attributes tunnel-group BACKDOORVPN

IKEv1 pre-shared-key *.

tunnel-group x.x.x.x type ipsec-l2l

tunnel-group ipsec-attributes x.x.x.x

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

Excellent.

Evaluate the useful ticket.

Thank you

Rizwan James

Connected to the Internet of VPN remote access VPN clients

Greetings,

I need to remote VPN clients to connect to the Internet from the same server VPN ASA

"client connects to ASA the external interface VPN tunnel can access Internet from the same external interface ASA new."

Thank you

you need to configure "same-security-traffic permit intra-interface" on the SAA.

Also, need to configure the relevant statements of nat for your range of pool of customers.

i.e.

Global 1 interface (outside)

NAT (outside) 1 access-list anyconnectacl

where anyconnectacl is the pool for your customers:

permit ip 172.16.1.0 access list anyconnectacl 255.255.255.0 any

Remote access VPN clients

Hello

I've set up IPSec VPN remotely and it works fine. I need access to connected VPN clients, and it does not work. I have already added an entry to traffic allowing sheep ACL from inside my network to the VPN.

More information:

Inside of the net: 10.1.1.0/24

Pool VPN: 172.30.1.0/24

Is it possible to access from my internal network to the VPN users?

Thanks in advance.

Best regards.

Marcelo

VPN users have access to certain servers via the list of Tunnel from Split.

Marcelo,

Split tunnel ACLs must be an IP acl, it is not recommended and supported to set the TCP ports on the split tunnel ACL, the vpn client don't interpret this ACl as a lot are interested in IP, TCP ports, and that could cause you a problem. You can change your config to reflect this. Regarding ACL split tunnel, it must contain the server line. networks that this vpn, customers arrive, remind you this is two-way, as you know.

So if IT supports the IP range is on this vpnExample ACL vpn clients will be able to reach the IT support guys and vice versa.

I advise you to change your split tunnel ACLs to specific ports to only the desired servers and the presenters what these customers need to achieve.

Remove the ports out of this Split tunnel ACLs.

If you need to restrict services for vpn rather clients use VPN filters.

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

Remote access VPN Client to PIX, DNS issue

Hi all. I searched on this, but I can't find my answer.

I set up a VPN connection to a PIX Firewall (running the version 8.0 (4)) for my business. The VPN connection works correctly, in that I can connect to it using my software (v 5.0.02.0090) Cisco VPN Client and ping servers/resources internal IP address. However, if I try to ping by host name, it does not resolve to an IP address. If I open a command prompt on my PC and type ipconfig/all, there are no DNS servers for my VPN, just for my normal Intel NIC adapter - I think I should have a DNS server listed under the map of VPN, right? Here is the relevant (I think) for the VPN config lines:

8.0 (4) version PIX

domain xx.xx

DNS lookup field inside

DNS server-group DefaultDNS

Server name 192.168.20.23

domain xx.xx

IP local pool vpnpoolIT 10.10.8.2 - 10.10.8.254 mask 255.255.255.0

Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

Crypto-map dynamic dyn1 1jeu transform-set FirstSet

Crypto-map dynamic dyn1 1 lifetime of security association set seconds 28800

Crypto-map dynamic dyn1 kilobytes of life 1 set security-association 4608000

crypto ISAKMP policy 1

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

tunnel-group ITGroup type remote access

tunnel-group ITGroup General attributes

address vpnpoolIT pool

Group-RADIUS authentication server

tunnel-group ITGroup ipsec-attributes

pre-shared-key *.

Am I missing? I can solve the DNS on the PIX itself requests.

All the info I can find online is for an older version of the PIX software which says that I should enter the vpngroup dns- IP address of the server command, but this command is not available in my version of the software.

Hello

To set a DNS server to be injected into the VPN clients when they connect, you can do the following:

This is the tunnel-group where lands the remote connection:

tunnel-group ITGroup type remote access

tunnel-group ITGroup General attributes

address vpnpoolIT pool

Group-RADIUS authentication server

tunnel-group ITGroup ipsec-attributes

pre-shared-key *.

For example, create a group policy:

internal VPN group policy
attributes of VPN group policy

DNS value--> x.x.x.x where x.x.x.x is the IP address of the DNS server

Then, apply the group policy for the Group of tunnel:

tunnel-group ITGroup General attributes

Group Policy - by default-VPN

It will be useful.

Federico.

Remote access VPN client to connect but cannot ping inside the host, after that split tunnel is activated (config-joint)

Hello

I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.

is hell config please kindly and I would like to know what might happen.

hostname horse

domain evergreen.com

activate 2KFQnbNIdI.2KYOU encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

names of

ins-guard

!

interface GigabitEthernet0/0

LAN description

nameif inside

security-level 100

192.168.200.1 IP address 255.255.255.0

!

interface GigabitEthernet0/1

Description CONNECTION_TO_FREEMAN

nameif outside

security-level 0

IP 196.1.1.1 255.255.255.248

!

interface GigabitEthernet0/2

Description CONNECTION_TO_TIGHTMAN

nameif backup

security-level 0

IP 197.1.1.1 255.255.255.248

!

interface GigabitEthernet0/3

Shutdown

No nameif

no level of security

no ip address

!

interface Management0/0

Shutdown

No nameif

no level of security

no ip address

management only

!

boot system Disk0: / asa844-1 - k8.bin

boot system Disk0: / asa707 - k8.bin

passive FTP mode

clock timezone WAT 1

DNS server-group DefaultDNS

domain green.com

network of the NETWORK_OBJ_192.168.2.0_25 object

Subnet 192.168.2.0 255.255.255.128

network of the NETWORK_OBJ_192.168.202.0_24 object

192.168.202.0 subnet 255.255.255.0

network obj_any object

subnet 0.0.0.0 0.0.0.0

the DM_INLINE_NETWORK_1 object-group network

object-network 192.168.200.0 255.255.255.0

object-network 192.168.202.0 255.255.255.0

the DM_INLINE_NETWORK_2 object-group network

object-network 192.168.200.0 255.255.255.0

object-network 192.168.202.0 255.255.255.0

access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

Access extensive list permits all ip a OUTSIDE_IN

gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

backup of MTU 1500

mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0

no failover

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm-645 - 206.bin

don't allow no asdm history

ARP timeout 14400

NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

!

network obj_any object

dynamic NAT interface (inside, backup)

Access-group interface inside INSIDE_OUT

Access-group OUTSIDE_IN in interface outside

Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10

Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254

Timeout xlate 03:00

Pat-xlate timeout 0:00:30

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

identity of the user by default-domain LOCAL

Enable http server

http 192.168.200.0 255.255.255.0 inside

http 192.168.202.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

monitor SLA 100

type echo protocol ipIcmpEcho 212.58.244.71 interface outside

Timeout 3000

frequency 5

monitor als 100 calendar life never start-time now

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

backup of crypto backup_map interface card

Crypto ikev1 allow outside

Crypto ikev1 enable backup

IKEv1 crypto policy 10

authentication crack

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 20

authentication rsa - sig

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 30

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 40

authentication crack

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 50

authentication rsa - sig

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 60

preshared authentication

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 70

authentication crack

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 80

authentication rsa - sig

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 90

preshared authentication

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 100

authentication crack

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 110

authentication rsa - sig

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 120

preshared authentication

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 130

authentication crack

the Encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 140

authentication rsa - sig

the Encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 150

preshared authentication

the Encryption

sha hash

Group 2

life 86400

!

track 10 rtr 100 accessibility

Telnet 192.168.200.0 255.255.255.0 inside

Telnet 192.168.202.0 255.255.255.0 inside

Telnet timeout 5

SSH 192.168.202.0 255.255.255.0 inside

SSH 192.168.200.0 255.255.255.0 inside

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 15

SSH group dh-Group1-sha1 key exchange

Console timeout 0

management-access inside

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal group vpntunnel strategy

Group vpntunnel policy attributes

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list vpntunnel_splitTunnelAcl

field default value green.com

internal vpntunnell group policy

attributes of the strategy of group vpntunnell

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl

field default value green.com

Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password

attributes of user name THE

VPN-group-policy gbnlvpn

tunnel-group vpntunnel type remote access

tunnel-group vpntunnel General attributes

address VPNPOOL pool

strategy-group-by default vpntunnel

tunnel-group vpntunnel ipsec-attributes

IKEv1 pre-shared-key *.

type tunnel-group vpntunnell remote access

tunnel-group vpntunnell General-attributes

address VPNPOOL2 pool

Group Policy - by default-vpntunnell

vpntunnell group of tunnel ipsec-attributes

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns migrated_dns_map_1

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the migrated_dns_map_1 dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

no remote anonymous reporting call

call-home

Profile of CiscoTAC-1

no active account

http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /

destination-mode http transport

Subscribe to alert-group diagnosis

Subscribe to alert-group environment

Subscribe to alert-group monthly periodic inventory

monthly periodicals to subscribe to alert-group configuration

daily periodic subscribe to alert-group telemetry

Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565

Hello

1 - Please run these commands:

"crypto isakmp nat-traversal 30.

"crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.

The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.

Please let me know.

Thank you.

ASA 5505 - remote access VPN to access various internal networks

Hi all

A customer has an ASA 5505 with a remote access vpn. They are moving their internal network to a new regime and that you would be the users who come on the vpn to access the existing and new networks. Currently can only access the existing. When users connect to access remote vpn, the asa gave them the address 192.168.199.x. The current internal network is 200.190.1.x and that they would reach their new network of 10.120.110.x.

Here is the config:

:

ASA Version 8.2 (5)

!

ciscoasa hostname

enable encrypted password xxx

XXX encrypted passwd

names of

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 200.190.1.15 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address 255.255.255.0 xxxxxxx

!

exec banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

connection of the banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

banner asdm the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

passive FTP mode

access extensive list ip 200.190.1.0 inside_access_in allow 255.255.255.0 any

outside_access_in list extended access permit icmp any external interface

access extensive list ip 192.168.199.0 outside_access_in allow 255.255.255.192 host 10.120.110.0

Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 200.190.1.0 255.255.255.0

MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

access extensive list ip 200.190.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

mask 192.168.199.10 - 192.168.199.50 255.255.255.0 IP local pool Remote_IPSEC_VPN_Pool

IP verify reverse path to the outside interface

ICMP unreachable rate-limit 1 burst-size 1

ICMP allow any inside

ICMP allow all outside

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 200.190.1.0 255.255.255.0

inside_access_in access to the interface inside group

Access-group outside_access_in in interface outside

Route outside 0.0.0.0 0.0.0.0 190.213.43.1 1

Route inside 10.120.110.0 255.255.255.0 200.190.1.50 1

Route inside 192.168.50.0 255.255.255.0 200.190.1.56 1

Route inside 192.168.60.0 255.255.255.0 200.190.1.56 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

http server enable 10443

http server idle-timeout 5

Server of http session-timeout 30

HTTP 200.190.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

Crypto ca certificate chain _SmartCallHome_ServerCA

certificate ca 6ecc7aa5a7032009b8cebcf4e952d491

(omitted)

quit smoking

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Crypto isakmp nat-traversal 3600

Telnet timeout 5

SSH 200.190.1.0 255.255.255.0 inside

SSH timeout 5

SSH version 2

Console timeout 5

dhcpd outside auto_config

!

a basic threat threat detection

scanning-threat shun threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

allow outside

internal MD_SSL_Gp_Pol group strategy

attributes of Group Policy MD_SSL_Gp_Pol

VPN-tunnel-Protocol webvpn

WebVPN

list of URLS no

disable the port forward

hidden actions no

disable file entry

exploration of the disable files

disable the input URL

internal MD_IPSEC_Tun_Gp group strategy

attributes of Group Policy MD_IPSEC_Tun_Gp

value of banner welcome to remote VPN

VPN - connections 1

VPN-idle-timeout 5

Protocol-tunnel-VPN IPSec webvpn

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list MD_IPSEC_Tun_Gp_splitTunnelAcl

the address value Remote_IPSEC_VPN_Pool pools

WebVPN

value of the RDP URL-list

attributes of username (omitted)

VPN-group-policy MD_IPSEC_Tun_Gp

type of remote access service

type tunnel-group MD_SSL_Profile remote access

attributes global-tunnel-group MD_SSL_Profile

Group Policy - by default-MD_SSL_Gp_Pol

type tunnel-group MD_IPSEC_Tun_Gp remote access

attributes global-tunnel-group MD_IPSEC_Tun_Gp

address pool Remote_IPSEC_VPN_Pool

Group Policy - by default-MD_IPSEC_Tun_Gp

IPSec-attributes tunnel-group MD_IPSEC_Tun_Gp

pre-shared key *.

!

!

context of prompt hostname

: end

The following ACL and NAT exemption ACL split tunnel is incorrect:

MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

It should have been:

Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 10.120.110.0 255.255.255.0

access extensive list ip 10.120.110.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

Then 'clear xlate' and reconnect with the VPN Client.

Hope that helps.

Problem with remote access VPN

Hello

I installed a remote access VPN on my firewall ASA5505 via the ASDM Assistant.

I can successfully connect with the Cisco VPN client. My firewall also shows me the VPN session and shows the Rx packets. However, Tx packets remain 0, so no traffic is getting out. My ASA5505 is configured as a router on a stick with 25 different VLAN. I want to restrict traffic to one VLAN specific using a card encryption.

When I run a command to ping t on my connected Windows box, the firewall log shows me the following message:

"Unable to find political IKE initiator: outside Intf, Src: 10.7.11.18, Dst: ' 172.16.1.1

"This message indicates that the fast path IPSec processing a packet that triggered of IKE, but IKE policy research has failed. This error could be associated calendar. The ACL triggering IKE could have been deleted before IKE has processed the request for initiation. "This problem will likely correct itself."

Unfortunately, the problem is correct.

The "sh cry isa his" and "sh cry ips its ' commands show the following output:

2 IKE peers: 62.140.137.99

Type: user role: answering machine

Generate a new key: no State: AM_ACTIVE

Interface: outside

Tag crypto map: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 85.17.xxx.xxx (outside interface IP)

local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)

Remote ident (addr, mask, prot, port): (172.16.1.1/255.255.255.255/0/0)

current_peer: 62.140.137.99, username: eclipsevpn

dynamic allocated peer ip: 172.16.1.1

#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

#pkts decaps: 4351, #pkts decrypt: 4351, #pkts check: 4351

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0

success #frag before: 0, failures before #frag: 0, #fragments created: 0

Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

#send errors: 0, #recv errors: 0

local crypto endpt. : 85.17.xxx.xxx/4500, remote Start crypto. : 62.140.137.99/3698

Path mtu 1500, fresh ipsec generals 82, media, mtu 1500

current outbound SPI: B3D60F71

current inbound SPI: B89BA14A

SAS of the esp on arrival:

SPI: 0xB89BA14A (3097207114)

transform: aes - esp esp-sha-hmac no compression

running parameters = {RA, Tunnel, NAT-T program,}

slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP

calendar of his: service life remaining key (s): 25126

Size IV: 16 bytes

support for replay detection: Y

Anti-replay bitmap:

0xFFE1FFF8 0xFFFFFFFF

outgoing esp sas:

SPI: 0xB3D60F71 (3017150321)

transform: aes - esp esp-sha-hmac no compression

running parameters = {RA, Tunnel, NAT-T program,}

slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP

calendar of his: service life remaining key (s): 25126

Size IV: 16 bytes

support for replay detection: Y

Anti-replay bitmap:

0x00000000 0x00000001

I really have no idea what's going on. I installed a remote access VPN countless times, but this time it shows me the error as described above.

Hi Martijn,

just a few quick thoughts:

-is your ok NAT exemption, i.e. ensure that the return traffic is not NAT' ed.

-Make sure that there is no overlap crypto ACL

-When connected, make a package tracer to see what is happening with the return packages.

for example

packet-tracer in the interface within the icmp 10.7.11.18 0 0 172.16.1.1 detail

(where is the name of the interface on which 10.7.11.18 resides)

This will show you all the steps the rail package in-house (routing, nat, encryption etc.) so it should give you an idea of what is happening, for example when it comes to the bad interface, nat evil rule, wrong entry card crypto etc.

HTH

Herbert

Remote access VPN with ASA 5510 by using the DHCP server

Hello

Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?

I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:

!

ASA Version 8.2 (5)

!

interface Ethernet0/1

nameif inside

security-level 100

IP 10.6.0.12 255.255.254.0

!

IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)

!

Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1

!

Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Crypto-map dynamic dyn1 1jeu transform-set FirstSet

dynamic mymap 1 dyn1 ipsec-isakmp crypto map

mymap map crypto inside interface

crypto ISAKMP allow inside

crypto ISAKMP policy 1

preshared authentication

3des encryption

sha hash

Group 2

life 43200

!

VPN-addr-assign aaa

VPN-addr-assign dhcp

!

internal group testgroup strategy

testgroup group policy attributes

DHCP-network-scope 10.6.192.1

enable IPSec-udp

IPSec-udp-port 10000

!

username testlay password * encrypted

!

tunnel-group testgroup type remote access

tunnel-group testgroup General attributes

strategy-group-by default testgroup

DHCP-server 10.6.20.3

testgroup group tunnel ipsec-attributes

pre-shared key *.

!

I got following output when I test connect to the ASA with Cisco VPN client 5.0

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO

4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID

Jan 16 15:39:21 [IKEv1]: Group = testgroup, I

[OK]

KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable

Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes

Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.

Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.

Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!

Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.

Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload

Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload

Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address

Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048) , : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740) , : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

Kind regards

Lay

For the RADIUS, you need a definition of server-aaa:

Protocol AAA - NPS RADIUS server RADIUS

AAA-server RADIUS NPS (inside) host 10.10.18.12

key *.

authentication port 1812

accounting-port 1813

and tell your tunnel-group for this server:

General-attributes of VPN Tunnel-group

Group-NPS LOCAL RADIUS authentication server

--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni

Cisco Asa 5505 and level 3 with remote access VPN switch

Today I had a new CISCO LAYER 3 switch... So here's my scenrio

Cisco Asa 5505

I have

Outside of the == 155.155.155.x

Inside = 192.168.7.1

Address POOL VPN = 10.10.10.1 - 10.10.10.20

3 layer switch configuration

VLAN 2

ip address of the interface = 192.168.1.1

VLAN 2

ip address of the interface = 192.168.2.1

VLAN 2

ip address of 192.168.3.1 = interface

VLAN 2

ip address of the interface = 192.168.4.1

VLAN 2

ip address of the interface = 192.168.5.1

IP Routing

So I want the customers of my remote access VPN to access all that these networks. So please can you give me a useful tip or a link to set up the rest of my trip

Thanks to you all

Al ready has responded

Sent by Cisco Support technique iPad App

RV042G REMOTE ACCESS VPN Config Shrew Soft

Hello

I am trying to set up a VPN with IPSEC remote access, I have a router Cisco Small Business RV042G. I have managed to connect with the QuickVPN client using a previously created user. I also managed to establish a connection with the TheGreenBow pre-shared key customer with customer authentication by IP address or by mail. Exactly the same method I managed with the Shrew Soft VPN Client. I would like to Shrew Soft VPN with only establish a connection with the nicknames as if only the pre-shared key is used all over the world can access VPN set up on this computer.

shrewsoftauthlocalidentity.PNG

shrewsoftauthremoteidentity.PNG

shrewsoftauthcredentials.PNG

To sum it up can you tell me what configuration must be put to use the identification of the user only with the Shrew Soft VPN Client?

Thank you very much.

Hello

Usually it is used Mutual PSK + XAuth, when you want to set up user and password, outside the pre-shared key authentication.

But RV042G don't support XAuth, which means that you can not create a separate user/pass to connect VPN Shrew.

Kind regards

Bismuth

Configuring remote access VPN

Hi all

I need help with remote access vpn configuration. I want to some remote users who have access to the internet on their system to connect and access an application server in my seat social cisco vpn client user. I use Cisco 881. I am unable to use the SDM configuration because it seems that SDM is not supported by the router so I'm using command line. I'd appreciate any help I can get. Thank you.

This is the configuration I have:

VPNROUT #sho run
Building configuration...

Current configuration: 6832 bytes
!
! Last configuration change at 10:50:45 UTC Saturday, May 30, 2015, by thomas
version 15.2
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname VPNROUT
!
boot-start-marker
boot-end-marker
!
!
logging buffered 51200 warnings
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login userauthen1 local
AAA authorization groupauthor1 LAN
!
!
!
!
!
AAA - the id of the joint session
iomem 10 memory size
!
Crypto pki trustpoint TP-self-signed-1632305899
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1632305899
revocation checking no
rsakeypair TP-self-signed-1632305899
!
!
TP-self-signed-1632305899 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31363332 33303538 6174652D 3939301E 170 3134 30313233 31323132
33325A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36333233 65642D
30353839 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100BC0C 341CD79B A38572CE 1F0F9A91 F96B133C A889B564 E8352034 1CF5EE4B
B505616B 6014041B EC498C0A F6C5CD2B F5BF62DA BD6E1C44 0C7B9089 1FD0C6E5
299CEB40 28CD3F3B ADE3468A B07AAA9F AC42F0A7 4087172A 33C4013D 9A50884D
5778727E 53A4940E 6E622460 560C F597DD53 3B 261584 E45E8776 A848B73D 5252
92 50203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 D
551 2304 18301680 14E85AD0 DEF133D8 E09516FD 0AA5FDAD E10EAB1A FA301D06
03551D0E E85AD0DE 04160414 F133D8E0 9516FD0A A5FDADE1 0EAB1AFA 300 D 0609
2A 864886 818100A 5 05050003 5B23ED5B 9A380E1F 467ABB03 BAB1070B F70D0101
7A 218377 73089DC1 D32DA585 C5FD7ECE 0D000F96 7F3AB6CC 71509E8F 3F1C55AE
E37536A3 1008FBF9 A29329D5 6F76DDC0 AA1C70AE 958AAE5D 32388BE4 2C1C6839
0369 D 533 027B612C 8D199C35 C008FE00 F7E1DF62 9C73E603 85C3240A 63611D 93
854A61E2 794F8EF5 DA535DCC B209DA
quit smoking
!
!
!
no record of conflict ip dhcp
DHCP excluded-address IP 10.10.10.1
DHCP excluded-address IP 172.20.0.1 172.20.0.50
!
DHCP IP CCP-pool
import all
Network 10.10.10.0 255.255.255.248
default router 10.10.10.1
Rental 2 0
!
IP dhcp pool 1
network 172.20.0.0 255.255.240.0
domain meogl.net
router by default - 172.20.0.1
172.20.0.4 DNS server 41.79.4.11 4.2.2.2 8.8.8.8
8 rental
!
!
!
no ip domain search
IP domain name meogl.net
name of the IP-server 172.20.0.4
name of the IP-server 41.79.4.11
IP-server names 4.2.2.2
8.8.8.8 IP name-server
IP cef
No ipv6 cef
!
!
license udi pid CISCO881-K9 sn FCZ1804C3SL
!
!
username secret privilege 15 thomas 4 JXSizd1r/hMqPpGz94vKBb5somtpZLy03k50rJvHO6c
username privilege 15 secret 4 mowe hlfv/rdDRCAeTUzRXbOIfdaKhJCl1onoGdaQeaQsAnw
!
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group moweclients
XXXXXXX key
DNS 172.20.0.4
meogl.net field
pool mowepool
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac moweset
tunnel mode
!
!
!
Dynmap crypto dynamic-map 1
Set transform-set moweset
market arriere-route
!
!
card crypto client mowemap of authentication list userauthen1
card crypto isakmp authorization list groupauthor1 mowemap
client configuration address card crypto mowemap answer
mowemap 1 card crypto ipsec-isakmp dynamic dynmap
!
!
!
!
!
interface Loopback0
IP 172.30.30.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
switchport access vlan 100
no ip address
!
interface FastEthernet3
no ip address
!
interface FastEthernet4
IP 41.7.8.13 255.255.255.252
NAT outside IP
IP virtual-reassembly in
intellectual property policy map route VPN-CLIENT
Shutdown
automatic duplex
automatic speed
mowemap card crypto
!
interface Vlan1
Description $ETH_LAN$
IP 10.10.10.1 255.255.255.248
IP tcp adjust-mss 1452
!
interface Vlan100
IP 172.20.0.1 255.255.240.0
IP nat inside
IP virtual-reassembly in
!
local pool IP 192.168.1.1 mowepool 192.168.1.100
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source overload map route interface FastEthernet4 LAT
IP route 0.0.0.0 0.0.0.0 41.7.8.12
!
access-list 23 allow 10.10.10.0 0.0.0.7
access-list 23 allow 172.20.0.0 0.0.15.255
access-list 100 permit ip 172.20.0.0 0.0.15.255 everything
access-list 144 allow ip 192.168.1.0 0.0.0.255 any
not run cdp
!
LAT route map permit 1
corresponds to the IP 100
IP 41.7.8.12 jump according to the value
!
route VPN-CLIENT map permit 1
corresponds to the IP 144
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
!
!
end

Please the configuration above, give me the desired output.

Thank you.

Hello Thomas,.

I'm glad to hear that you have found useful in the example configuration.

I checked your configuration and everything seems ok with him, especially the statements of nat.
```
 ip local pool mowepool 192.168.1.1 192.168.1.100 access-list 100 deny ip 172.20.0.0 0.0.15.255 192.168.1.0 0.0.0.255 access-list 100 permit ip 172.20.0.0 0.0.15.255 any route-map LAT permit 1 match ip address 100 ip nat inside source route-map LAT interface FastEthernet4 overload interface Vlan100 ip address 172.20.0.1 255.255.240.0 ip nat inside ip virtual-reassembly in 
```
Try to generate ICMP traffic behind your 100 VLANS to the client VPN in order to answer the following questions:

-The router receives this traffic between VLAN100 unit?

-The router is encrypt this traffic, after receiving the ICMP packet?

#show crypto ipsec router its can help you with this question. Look for the program/decaps counters.

-The same, but the other way around (from VPN client to device behind VLAN100) try to locate the problem.

The following document explains more this crypto commands and debugs if necessary.

http://www.Cisco.com/c/en/us/support/docs/security-VPN/IPSec-negotiation-IKE-protocols/5409-IPSec-debug-00.html#iosdbgs

PIX 515E and remote access VPN

I use a PIX 515E with: ASDM Version: 5,0000 51 PIX Version: 8.0 (4) and configure it with remote access VPN.

I would like to get an email every time that a user login (and or disconnection) to the VPN. Remote clients use the Cisco VPN Client.

Any help is appreciated,

Hello

Here is a link to the email configuration when you log in to the ASA/PIX: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc7

Then you can create a list of message to send the logs only for the connection/disconnection of the VPN user: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc18

There is a wire that is linked here: https://supportforums.cisco.com/discussion/10798976/asa-email-logging-issue

DMVPN with based remote access VPN client

Similar Questions

shrewsoftauthlocalidentity.PNG

shrewsoftauthremoteidentity.PNG

shrewsoftauthcredentials.PNG

Maybe you are looking for