Do cRIO 9014 Wireless

I'm working on a project which, due to the location of the cRIO he will be no close ethernet cable. A solution that I've looked at is to connect a wireless for the cRIO bridge and then connect the bridge to a signal from router available. I looked at the first competition and they use this solution to control of robots. Does anyone know how it works and if it is a reliable solution?

I have to install it at school so I don't know if this works with DHCP or if I should request a static IP address.

Gerardo Trevino,

I helped with the FIRST Robotics competition and the only problems I've ever seen with the wireless setup were typical problems related to Wireless Communication (range limits, network dropouts, etc.).

To make your cRIO wireless you can definitely use this method and it should work perfectly, I did personally and have not had any problems.

Check out the tutorial that we have on our Web site for making of PACs wireless NOR industrial Wi-Fi access points. You can also see the 3rd party WiFi Module cRIO.

It is possible to do with DHCP, but set all of your addresses statically makes things a lot easier in a closed/private network environment.

Tags: NI Hardware

Similar Questions

  • deploy programmatically variable shared within the standalone version of RT (cRIO-9014)

    Hello

    I have a question about here to use variables shared single process within the standalone version of RT for the cRIO-9014

    I simplified my request of LV (LV2010) in two to test the use of shared variables.  See the attached file.

    (1) only run on the host PC: testHost
    (2) only works on the cRIO-9014: testRTcRIO

    for both, I packed stand-alone executable and source distribution.

    for testHost,.
    (a). I copied \builds\testcRIO\Host to d:/or-rt/xmlrpcFEU source Distribution...
    (b) I run... \builds\testcRIO\Host.exe
    (c) xmlrpcFEUlog - host.txt is generated.

    for testRTcRIO,.
    (a) .d FileZilla to connect to the target of RT on network, I copied... \builds\testcRIO\Source Distribution\c\ni - rt\xmlrpcFEU

    to/or-rt/xmlrpcFEU on the target of RT
    (b) I copied also... \builds\testcRIO\Real-Time Application\c\ni - rt\startup to/or-rt/startup on the target of RT
    (c) Max, I restarted the cRIO-9014.
    (d) xmlrpcFEUlog - RT.txt is generated.

    We see that the shared variable does not work inside the RT target. but worked well on PC. the deployment programmatically method does not work.  any suggestion?

    Another thing is:
    can I use telnet for the RT 9014 target and start the RT app directly? What is the command inside the terminal telnet RT?

    Currently, I can telnet into the cRIO-9014, but, what I can do with it?

    ================
    220-national Instruments FTP
    220 service Ready

    530 journal please with USER and PASS
    USER
    331 user name okay, need password
    PASS
    230 user logged
    Help
    211 - USER PASS ACCT STRU TYPE
    211-MODE CWD XCWD PWD XPWD
    211 CDUP XCUP PASV, RETR, REST
    211-PORT LIST NLST QUIT SYSTEM
    211 STAT HELP NOOP STOR, APPE
    211 STOU HELLO MKD XMKD RMD
    211 XRMD DELE, RNFR TRAVEL SIZE
    211 MDTM
    ===========================

    Concerning

    Xiaofeng


  • make a request using pt100 with cseries 9219 module and crio 9014

    How can I connect my module pt100 with series c 9219 module and crio-9014

    The description is in table 1, but they are signals and lines of the TEDS data COM. More information on TEDS found on page 11 of the manual and a page of links to http://www.ni.com/white-paper/3468/en.

  • cRIO-9014 & RS232

    I take my first steps with a cRIO 9014 - for a running on the target FPGA VI, is it possible to use the RS232 port on the cRIO as output?

    Hi SamD,

    In response to your question, I make a few assumptions. I guess that your VI is running on the FPGA in your cRIO. In this case, the answer is no. Only the target in real time can access the serial port, so you would need to provide an interface between the FPGA and the serial port (running on the target RT).

    I've also attached a knowledge base article that explains how to implement RS - 232 with FPGA hardware OR but you would need to add some additional hardware to do this. I recommend the Developer Zone article.

    I hope this helps.

    Thank you very much

  • cRIO 9014, FPGA compiler error

    I use cRIO 9014, that while the FPGA code compilation I get attached error.

    Please guide me ob who...

    Hi Olivier,.

    The displayed error is clear.

    Your system time is older than the time of installation.

    Change to correct time and try it...

    In addition, if you change your system time (IE computer), some software will not work. (another example is Gmail. Try to connect to Gmail after year settting in the previous year in your system. It displays error SSL.).

  • Use of VxWorks memory - cRIO-9014

    Suggestions how to monitor the memory usage in the RT on the cRIO itself?

    You should have access to this palette.

  • Plug-in for the selected item. CRIO-9014 TR

    Hi all

    At the opening of project built in LabView 8.6 I get a warning (Please find the attachment). I can't recall what I need plug-ins start?  Can it be related to vi wrote to RT? Maybe one of them uses toolkit, that I have not installed?

    For support for LabVIEW 2009, you will need to update your version of NOR-RIO.

    The latest version is NEITHER-RIO 3.2.1 which can be downloaded here http://joule.ni.com/nidu/cds/view/p/id/1386/lang/en

  • CRio-9014, 9116 and 9870 - series write does not


    Hello

    Yes, I was able to get things going according to my needs. There was a problem with the connector DB9 not wired correctly and Blayne Kettlewell, ELP Engineer at National Instruments helps flatten out. We are in business.

    Thank you

    Ajay

  • cRIO: build the path to write tdms file on a USB flash drive

    I wrote the code in figure 1 below, for open & create a file tdms on my USB flash drive that is plugged into the USB cRIO.

    The added path tdms is shown in figure 2 below.

    But I get the error in figure 3 below. I wonder how I can solve this problem.

    Cashany,

    Make sure that the USB is formatted in FAT32 as the cRIO cannot mount NTSF or other file systems.

    In addition, and this is potentially very important:

    There is a known memory leak problem that is easy to avoid the code with the help of PDM on the cRIO (without code changes!).

    This problem only occurs on vxWORKS targets (e.g., cRIO-9014), not on the PharLap targets (as I know).

    The problem occurs when you close a PDM file reference, the vxWORKS OS can't properly unload the PDM library. Next time you open a PDM, the library reference is loaded again, if for a very long time you will run out of memory.

    The solution is very simple:

    on your cRIO, locate the file or - rt.ini, then scroll down to the section [LVRT] of the ini file and locate the key called "StartupDlls".

    Make sure 'tdms.out' is included. For example, according to your cRIO, it may look like this:

    StartupDlls = nisysrpc.out; NiRioRpc.out; NiViSrvr.out;

    In this case, you would change the line to look like this:

    StartupDlls = nisysrpc.out; NiRioRpc.out; NiViSrvr.out; TDMS.out;

     

    This will prevent the LabVIEW runtime on the cRIO trying to unload the PDM library, forcing to be in memory of start up to eternity. This avoids the memory leak that you would otherwise experience.

    Good luck!

    Q

  • CRIO save in memory

    Hello. I am new to Labview and CRIO. I asked were I want to record 24 channels of data at 50K samples/s for 2-3 seconds. I am able to follow this example.  http://zone.NI.com/DevZone/CDA/EPD/p/ID/5919

    However, I didn't need to stream from the host PC, but rather pick them up on the CRIO drive.  I've read it seems that the limitation of the drive is about 1.5 to 2MB per second.  In my example, it would be about 5 MB/s (50 K * 24channels * 4 bytes).   So I created a VI that, instead of streaming, just written in a very wide range.  This is sounds plausible?  When I pick up enough samples, I'll then write to the disk. But it seems that even a 500K array seems to make 100% of the CPU usage.  I'd like to use streaming, however, I have will increase to 48 channels shortly.  It says the cRIO has 128MB DRAM, I guess that's where the table would be created?  Any help is appreciated.  I can attach my code if necessary, but would just have a few tips.  Thank you.

    CRIO-9014

    LabVIEW 8.6

    6 - 9233 modules analog data acquisition, a 9215 analog module (trigger in)

    Christian,

    Wow! I must say that this is the example simpler, more organized I met.  The project worked perfectly.  I must just add my e/s.  Program streams, it is thin, and everything has an end.  I think that me trying to do something that it was not designed to do this example continuous causing me me a lot of grief.  I seem to have all the pieces of the puzzle, but they could not meet.  This project is a good example of fantastic programming.  Thank you very much.

  • Why the memory usage of my place of cRIO until the accident?

    Olla and servus Hello,

    I have another problem with my test setup!
    A cRIO-9014 with 9118 chassis and modules.

    The problem manifests itself in a way the cRIO hangs after some time. During this time, I went up to now that it is the use of the memory of the controller! This is the beginning of the Proggramms RT to ~ 40% but continues to increase. Until there are about 98%, and the connection is lost to the target system.

    Do you have any idea what may be the reason.

    Thank you very much for your answers!

    MaJahn


  • How to run terminal console of the CRIO output rtexe

    Hello

    I want to run the rtexe application in CRIO (9014) from the console output terminal. In my application the availabe lan port is connected to any other device using cross-over cable. That's why I want to change application console using the console terminal. I tried the taskspawn command but the crio restarts. Is there a command so that I can run the terminal console application.

    ... I don't know how to get any input from keyboard (the new path of application) of the console terminal...

    You can use the interface for RS232 communication standard series. If for example you send 1, 2 or 3 as a string to the cRIO and then you change by program the ni - rt.ini to change the path of access between a startup2.rtexe and startup1.rtexe, startup2.rtexe.

    Moreover, I have to restart the controller every time I change the path.

    When you use the method with the executable and then one more, then Yes.

    IAM cannot use the Subvi because I need to change code fpga also to different instances.

    I don't understand why using SubVIs on the RT does not give you the ability to change the fpga code.

    If the second method example would be Sub1.vi, Sub2.vi and Sub3.vi. When you get the 2 interface command series, you close the reference to the FPGA1.vi that is used in Sub1.vi and stop Sub1.vi. Then, you start by program Sub2.vi where you open and run the FPGA2.vi.

    Christian

  • With the help of two CAN channels on cRIO with 9853

    I have a cRIO 9014 controller RT and 9112 chassis and a CAN Module 9853.  I used successfully CAN receive and channel CAN Transmit example projects to check the work of material.  Then, I took two screws FPGAS of each project and grouped in a single FPGA VI by copying just the two in the same VI.  I can correctly transmit and receive with the host live

    My goal now is to be able to use the two CAN channels on the module 9853 for transmitting and receiving CAN Messages on each channel.  I like to use in a project in hybrid Mode later, so I think that there is only a single DMA channel available after that Scan Engine takes 2.  Maybe that's why I get an error when I make a copy of everything in the FPGA VI, make a new FIFO and make copies renowned host of screws with different names of variables to match the copied content from FPGA VI.

    Any other ideas on how to proceed would be appreciated.

    Also, I know that CAN1 needs an external power supply, so it is no more a problem.

    Thank you

    John

    I thought about it, I don't know why, but some parts with part 'FPGA to receive channel CAN' in their own lines fixed.  Now CAN receive is as fast as can be, never drop frames or overflowing the FIFO.  He also compiled FPGA Bitfile 30% faster and was about 50% less use of the device.  Weird...

    If you're curious, here's the new VI:

    John

  • Host VI and cRIO execution time

    Hello

    I have a cRIO 9014, I run an application real-time with two loops and a host of VI in my PC, the host VI is slow kynda, but I would like to know if there is a way to check if the cRIO rotates at the speed it should run.

    Thank you.

    -Luis

    Luis,

    Here are the two methods for timing your code that I described in my last post. The top then loop uses a shift for you register say how long (ms) takes of each iteration of the loop. The structure of the bottom flat sequence will measure how much time (ms) a section of code takes to run.

  • Remotely to access the variables of the cRIO

    I have a cRIO-9014 with a cRIO-9114 which is used as a stand-alone system controller (we use several types of modules c I / O and DI/O).  I want to connect a cable ethernet and view select input/output to facilitate tuning PID control.  I am currently using global variables for communication between the host on the PC and the vi rtexe vi.  This works that whent the vi rtexe is launched from the PC.  If I try to launch the host program, while the rtexe is running on the cRIO, when variables deployment stop the rtexe.  If I prevent deployment variables, global variables in the host are not communicating with the cRIO.   Anyone know how to get data in real time of the CRIO without interrupting the program running on the cRIO?

    Thank you!

    If you use variables published shared network and host them on the target (make sure that the library is below the target in the Project Explorer), variables will be deployed when you start the host VI. This way you will not interrupt the program of control over the cRIO.

    See the knowledge base article: How can I deploy a compiled executable shared network Variables? for more information.

    Hope this helps,

Maybe you are looking for

  • Upgrade hardware for Satellite A300D - 15 c

    I want to ask is able to change this model motherboard / graphics card / hard drive, because I like to get my computer a little faster and get more memory?

  • P750-114 satellite is unable to respond to the touchpad

    Hello I can't use the mouse pad. Sometimes it gives a bit of his interruption and does not respond to mouse movements. Sometimes he answers but only very little time. This is a brand new and absolutely don't know if something to do with the drivers o

  • error 0xe0ef0003

    Hello, I have a laptop HP G42 and lately he has had problems. When I turn it on a blue screen there sometimes, but when I'm actually able to connect it is super slow. I decided to restore factory that and it wouldn't let me click on the button. Long

  • Log on problem after installation of the sp3

    Hi there forgive me if this is old news, but I just bought an old laptop for children. The seller has installed xp pro top with IE 8. I installed the latest java, W. Media Player. I had a browse through updates and he said that auto updates can not b

  • Cannot right click programs to send the shortcut on the desktop

    I want to create a shortcut on my desktop for some programs listed in the start menu.  When I right click on the screen flashes but I don't get the box that will let me send the shortcut for the program on the desktop.