Do not connect ANALOG and digital grounds when the annotation to the front at the UB

Similar Questions

• NEITHER USB-6343 analog and digital grounds

  In the manual for the NI USB-6343, it is said that the mass input/output, analog and digital terrestrial are related, but by a small sign. For my application, I am attaching all 3 these grounds to exit the box (I'm tie all areas with physical threads). It is perhaps a silly question, but it's OK to do, correct?

  This should be OK unless there are large currents flowing on ground conductors.  If you have important currents in the ground, you have other problems that must be resolved before you connect the DAQ hardware.

  Lynn

• Synchronization of analog and digital output with the external sample clock

  Hello

  First of all sorry for my English, I will try to explain what I want to do.

  I want my PCIe-6321 to send two custom signals (modification sawtooths) on a mirror controller. I would also like to generate output with my card at the beginning of each tooth of saw. Everything must be synchronized with an external k-clock signal of 100 kHz. The idea is that whenever the PCI receives a trigger to external clock, it sends two analog output voltages and when he received 1024 clock ticks it will also send a pic of triggering TTL. What I do is first prepare the map and after that in a loop sending and modifing the output values of the two signals and at the same time send a digital signal Boolean in each arch, so when's done it 1024 iterations of the loop I send an event to the digital port. Attached you can see.

  The problem is that I don't know how to synchronize both. Can I use the sample clock just to the analog output? I can use sample for the two outputs clock, or do I need to use the output of the meter? If don't know how to use it here.

  If I do nothing else bad/wrong, I would be grateful for feedback.

  Thanks in advance,
  Pablo

  I don't know how but I find the solution. I'm generating more than a positive value (as I was triggered maybe very fast the oscilloscope has been absent there). If I put the sample clock of digital output to use the sampling/ao/Dev1 clock that it doesn't, but if I put to use the same source as the OD (terminal where my external clock is connected), but the trigger to start the DO to be Dev1/ao/StartTrigger this works. I don't really know why, but it does.

  Thank you for your patience and your help. I put here the final code.

• analog and digital data synchronization

  Hi all

  I would like to help with what I seek to accomplish, if you don't mind much.

  I'm trying to synchronize the acquisition of analog and digital modes using a common trigger that launches both types of data collection at the same time. What I've done so far, is wasting his time trying different combinations to gather examples of LabVIEW 2011 on the synchronization of data - namely the 'Multi-multifunction-Synch AI lu Dig Chan.vi' and 'Multi-Device Synch-Analog Input-Finite Acq-Analog Start.vi.

  I tried to combine the two, because one contains digital and analog, the other contains the trigger for multiple tasks.

  I guess I should place the trigger (either digital or analog-eventually I will want to choose) then call the "Get Terminal name with device Prefix.vi. But from there I'm not sure wheter to connect the name of the terminal of the sample clock digital channel or a digital leading edge of the digital chain trigger.

  Also, the way it is wired now I get errors at the local terminal name, so I don't know exactly where this terminal must come from.

  I try my best, I could use a little help, I have attached my attempt with the examples that I speak to you.

  Thank you.

  Hi beefcake.

  The CtrInternalOutput internal output line is used as sample for your digital output sample clock source clock. If you change the settings for your CO Pulse Time is Dev1 and your digital output is Dev2, you will notice that the name of the product terminal would give Dev2/CtrInternalOutput. So what you get here, it's as well as the digital output device sees his sample clock, instead of the clock itself.

  If you just want to use a digital/analog input as your trigger, you should do something more as in the example above. Do you use multiple devices, or are all your lines on the same device? This example is more complicated because it is synchronization of signals on several devices.

  Looking at how this VI is wired, you can see that the digital signal triggers the analog signal. You want the analogue signal must be started first, so that when the digital signal triggers the analog task is already running and can trigger immediately. If the digital task started first, it can trigger until the similar task had started, and they do not exactly trigger at the same time.

  I hope that clarifies things. Kind regards

• Is it possible to cut all the sounds and haptic feedback when the iPhone is connected to Carplay Apple?

  Is it possible to cut all the sounds and haptic feedback when the iPhone is connected to Carplay Apple?

  While driving, I noticed that all the comments navigation are also sent to my phone, creating a distraction while driving. Is there an automatic way to stop sending alerts to my watch whil the iPhone is also connected to Carplay?

  If this is not the case, consider this as your comments/request. If there is, please share. I do not want to switch manually and on all notifications when you use Carplay.

  Best regards

  Q

  Hello

  It may help to place your watch in mode do not disturb before driving:

  -On your watch: when the time display, drag upward on the dial of the watch > drag left/right to the gaze of settings > tap the moon to turn do not disturb on and outside.

  You can also disable mirroring for do not disturb mode. When mirroring is enabled, turning on do not disturb on your watch also automatically her allow on your iPhone.

  -On your iPhone, in the application of Eve, go to: Watch My > General > do not disturb - turn the market / stop iPhone mirror.

  To send comments and/or service requests to Apple, you can submit the form here (all comments are read):

  https://www.Apple.com/feedback/watch.html

  (This is a supportive community focused on user - you don't talk to Apple here).

• I can not get the automatic updates on my samsung jack sgh-i616. _ "connection to the update server is not available. Check your data connection settings and make sure that the device date and time are correct "___RESULT CODE: 80072ee7__ _"

  I can't get the automatic updates on my samsung jack sgh-i616.

   

  "Connection to the update server is not available. "Check your data connection settings and make sure that the device date and time are correct.

   

  RESULT CODE: 80072ee7

   

  -It is a windows mobile 6.1
  
  
  Thank you very much! = D

  As a guide.

  This error code translates ERROR_INTERNET_CANNOT_CONNECT.

  You may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/836941

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• can not connect password and username on.forgot

  can not connect password and username on.forgot

  If you are using XP Home Edition, the built-in Administrator account probably doesn't have a defined password. You can start in safe mode, where this account will be selectable when connecting. It allows to connect and change the password of any other connection.

  To start in safe mode, keep hitting F8 twice a second after turning on the PC until you get the start menu where safe mode is selectable by the up/down arrow keys, and then press ENTER.

  If you are using XP Professional, try to connect using the built-in Administrator account. You don't need to do it in safe mode (although you can if you wish). If your normal login screen is a display of the user symbol and hit ctrl-alt-del twice to get to login to text entry. Type administrator as the user name and try a blank password.

  See also http://support.microsoft.com/kb/321305

  Other than the foregoing, this forum has a policy that prohibits assistance to crack passwords.

  Tricky

• I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

  Turn off the new modem for at least 30 minutes. More is better.

  Perform a hard reset on the AirPort Extreme, then it turned off.

  Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

  After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

  Then, turn on the airport and let it run a few minutes

  Set up AirPort Extreme again

  Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

• How to trigger and outputs analog and digital Outout tasks begins on a counter to start?

  Hello

  I'm trying to synchronize the start of a task outputs analog, a task of digital output and a task of counter. I want to start the counter to serve the master trigger and analog and digital tasks to synchronize his departure.

  I guess I need something like:

  analogOutputTask.Triggers.StartTrigger.ConfigureDigitalEdgeTrigger ("?", DigitalEdgeStartTriggerEdge.Rising);

  digitalOutputTask.Triggers.StartTrigger.ConfigureDigitalEdgeTrigger ("?", DigitalEdgeStartTriggerEdge.Rising);

  analogOutputTask.Start (); Slave 1

  digitalOutputTask.Start (); slave 2

  () counterTask.Start; n / / master

  Where? is a string specifying a command source for the beginning of the task of the meter. However, I can't find what this string. Any suggestions?

  Thank you!

  -Jon

  Just FYI, the solution to this problem as well as some other ones is encapsulated in a short example .NET, I created. It is on the Web site of EITHER:

  http://decibel.NI.com/content/docs/doc-15500

  This project shows how to synchronize all your analogue/digital outputs through tasks and forums in terms of synchronizing Calendar and start clock.

  -Jon

• Cannot install adobe creative suite 6, do not load and install further when the second cd is inserted (zip also does not work)

  Cannot install adobe creative suite 6, do not load and install further when the second cd is inserted

  This question is unanswered.

  artistichooves artistichooves February 6, 2014 06:31

  I've only had 3 programs installed with the two cd I got with my adobe creative suite 6 (edition education, student and teacher)

  It didn't load any further when I insert the second cd. (tried several times) on my windows 8.1

  I got a license number, but it does not work on the creative cloud

  I tried to download the zip file, but it did not work

  I have ragequited (sorry)

  and now I want to try again.

  -J' have the license but I can't use my cd or download the zip

  -are there a cd I can buy again or something?

  It seems that my series works more :/

• I can not connect to my computer laptop get "the Group Policy client service has no connection. Access denied. "

  I can not connect on my lapto even if the password is correct. I'm getting "the political group Clinet impossible service connection access Denined.

  Original title: I can not connect on my laptop even if the password is correct

  HI, John Angelo2,.

  Try rebooting and tapping F10 to achieve the recovery screen

  You can choose to repair or restore your system

  Select Restore to an earlier time

  If it is impossible to do the above, use the installation start screen repair DVD

  This problem is caused by your user profile/registry settings/system files corruption

  Response of Mouneshawar R.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/the-Group-Policy-client-service-failed-the-logon/6b069a74-8524-442c-8ff1-d723e2a4e992

  Re-create the profile or restore the file ntuser.dat from the back to the top

  http://social.technet.Microsoft.com/forums/en-us/itprovistaapps/thread/c88515b4-4be7-4f6f-9988-80f8a5683b41/

  You can post on the Technet forum for help

  How to customize the default local user profile when you prepare an image of Windows Vista, Windows Server 2008, Windows 7 and Windows Server 2008 R2

  http://support.Microsoft.com/kb/973289

  Assign a mandatory user profile

  http://TechNet.Microsoft.com/en-us/library/cc786301 (WS.10) .aspx

  http://support.Microsoft.com/kb/307800

  http://msdn.Microsoft.com/en-us/library/bb776895 (v = vs. 85) .aspx

• M1536dnf - the installation program could not connect to your device. Check the IP address

  I recently bought a LserJet Pro M1536dnf for my business, then we would have network printing and scanning. We have both Mac and Linux PC with a single machine Windows solitaire which is kept away from the network for his own protection, and I expect from Linux but this is not where the problem is. Due to our network configuration, the only way to connect to the printer is by IP, not not using Hello. When installing using the installer of HP on the Mac, I choose 'Add intellectual property arrangements', enter the IP (192.168.1.247) and click OK. After that, he always comes back 'the installer could not connect to your device. Check the IP address, make sure that the device is powered, and then try again. "I know I can get to the printer because I can access its web interface in Safari. I tried to reset, update firmware, reboots, power-off/power-on different computers, nothing works.

  Curiously, I could add the printer very well on Ubuntu Linux computers and print immediately, although the scanner still doesn't work here. So my problem is on the Mac.

  OK, I have now works. The HP installation program provided on the CD-ROM supplied with the printer does not work. After you download the new version of support.hp.com, I could successfully add the printer by IP address.

  Also, just a quick note to all the world using Linux (although it is not officially supported by HP):

  The printer works fine, using HPLIP, but requires at least version 3.11.1 to work. I had to add an additional to my linux installations software source to make it work.

  Under Ubuntu 10.04/10.10, add:

  PPA:hplip - isv/ppa

  Other Linux distributions will be different, if you are having problems check to see how to install the latest version of HPLIP software.

• Satellite Pro M10 will not start again and comes up with the error message

  My laptop Toshiba Satellite Pro M10 will not start again and comes up with the error message "load error" when I press the power button.
  The arised problem after installation of the 'symantec system works' and try to restart windows XP Professional to make the installed executable program.

  What can I do to get the notbook again reboot?

  Hello

  Seems that there are problems with the files of GoBack.

  Try to boot in safe mode and remove the Norton System works from your laptop ;)
  If this does not help, you will need to recover the laptop with the recovery CD Toshiba delivered!

  Also I recommend to visit the Symantec support site and to check the solutions to the problem with the Norton System Works programs

  Good luck

• Watch does not recognize the weight class as exercise-how can you add the duration of activity manually because none of the presets eg elliptical etc. is appropriate. Also does not count calories for example 35 when the rest of the group is around 500

  Look does not recognize the weight class as exercise-how can you add the duration of activity manually because none of the presets etc for example elliptical is appropriate and therefore do not count toward the daily goal. Also does not count calories for example 35 when the average of the others in the group is around 500.

  Hello

  When you use the application of the training session, choose the type of activity that best fits your business. For anything else - like weight - select the other category.

  During the follow-up of one year to the next helps:

  • Activity app will credit the ring of progress of exercise with one minute for every minute of the workout.
  • Active calories will be based on the data recorded by the heart rate sensor or a brisk walk, whichever is greater.

  Note, however, that the heart rate sensor is likely to give better results for the workouts that involve rhythmic (for example running) rather than the irregular movements.

  More information:

  Use of the workout on your Apple Watch - Apple Support

• I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  original title: alternate tcp/ip

  If by "alternate TCP/IP configuration" you mean the settings on this screen--> http://tinyurl.com/42kbqqz, then, to quote Inigo Montoya, "you keep using that Word. I don't think it means what you think it means. »

  The 'alternative' configuration settings tab, if you select "IP address private auto" (APIPA) or "specified user" is only used IF "obtain an IP address automatically" is set on the tab 'General' (http://tinyurl.com/8p9hn) AND the adapter cannot get an IP from a DHCP server.

  Most cable networks use a DHCP server to automatically assign IP addresses.  In this case, just plug your Ethernet cable and you're automatically configured and connected.

  If the problem is that your network requires a static IP address (that is, they use a DHCP server to automatically assign IP addresses), you will need a third-party network settings manager.  If you have an IBM (Lenovo) ThinkPad, you can use "Dial-up connections." IBM Otherwise, see this Google search (I have no experience with any of the applications shown, so I can't comment about them): http://www.google.com/#sclient=psy&hl=en&source=hp&q=network+configuration+switcher&pbx=1&oq=network+configuration+switcher&aq=f&aqi=g-v5&aql=&gs_sm=e&gs_upl=23l1333l1l1599l12l8l0l0l0l5l278l1344l0.7.1l8l0&bav=on.2,or.r_gc.r_pw.&fp=74e371c96a48f4b&biw=1024&bih=649