Does not start with the new graphics card

Similar Questions

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Computer does not start with the new video card

  Hello

  I have hp pavilion 500-277cb and I love it, but it won't work with my new video card

  The video card is
  Sapphire ATI over-pants 2460

  I heard 6 beeps and I turned off safe and active start legacy. It does not beep, but it is not start either, just black screen.

  It seems to me to have the latest version of the bios and windows 8

  What can I do else?

  Thank you very much

  Best,

  Korhan

  Hi JM,

  Did you remove the Intel HD graphics drivers prior to installing the ATI graphics card?

  Your PC comes with one of the following built-in Intel graphics drivers:

  • Graphics Intel HD 4400 (GT2)

• Lenovo M91p desktop does not boot with the new graphics card (Blank don't screen no BIOS)

  Hi all

  I recently bought a Lenovo M91p thinkcenter Desktop as an upgrade to my old PC i3.

  Old Spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Intel DH55HC
  • Processor i3
  • Graphics HIS HD Radeon 7950
  • 8 GB RAM
  • HARD DRIVE 500 GB

  I transferred my HD supply and Power 500 GB old to new Lenovo desktop and everything starts very well.

  Then I installed 2 x 2 GB extra in the Lenovo M91p (which in fact 8GB) and updated the disk of 500 GB to 1 TB.

  So my new spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Lenovo Q67
  • I7 2600 3.4 Ghz CPU
  • 8 GB RAM
  • 1 to and 500 GB HARD drive

  Everything Booted fine. Then I tried to install my old graphics (HIS 7950 graphics Radeon HD card) card. I got was a blank screen, no beeps, no BIOS... Nothing.

  At first, I thought that my diet was not enough... So I tested a 750W power supply in the pc. Still nothing.

  Then I thought that the motherboards BIOS was outdated... Updated... Still nothing. I even tried to update the firmware of the graphics card. Nothing.

  The graphics card works because I tested it in my old machine and it worked 100%.

  However, I took my graphics card to my provider and he tests it on another of his pieces... Did not work there either.

  My PC BIOS is not supported for secure boot, in case anyone wants to know.

  I am out of ideas now... Anyone able to help?

  There is a white list of graphics cards that will recognize the BIOS. The 7950 HD is a map of 180w, well beyond what the power plant can provide (and case/sufficient cooling fans for) and not a single one is that Lenovo would provide support for the BIOS.

  Use the search engine above to see what cards other owners have used successfully in their M91p.

• Satellite A110 - switch WiFi does not work with the new WiFi card

  Hello everyone

  I have a problem with my laptop Toshiba Satellite A110 - 178 (PSAB0E). I replaced the original Intel 3945abg with Intel Link 5100 WIFI card and on the new wifi hardware wifi card switch does not work.

  New wifi card is discovered and drivers to the correct job but when I try to search with the Intel Pro/Wireless software wifi networks I message to turn on hardware switch, but there light and not work. The old wifi card swich works OK - orange light is on. On the new map light is off and swich does not work.

  Help, please

  Hello

  Do you have also enabled the WLAN functionality by pressing FN + F8?
  Check it!

  In addition, I think the case is clear: the new wireless LAN card isn't compatible with Satellite A110.
  So in my opinion, you must use remove the new card Intel and install the old card that works fine in your laptop.

• BlackBerry 8250 new smartphones does not start with the connected SIM card

  I'm having a problem with my new Blackberry of Virgin Media (mobile).  I just got it and when I have a connected SIM card I only get the loading screen timer and the blackberry does not start.  If I have no connected SIM card the device starts in the operating system, but was told that there is just no SIM connected (obviously).  Once I put the SIM card in again once it is stuck on the loading screen.  As you probably already figured out that I did many resets hard with the battery pull and it has not solved the problem.  A consultant because it would be greatly appreciated because the only advise I got support was remove the boot of sim and put it back and start again duh!

  Carrier - Virgin Media / Vodafone
  Model - 8520
  Version of the OS - 4.6.1
  Free space - 130679088 bytes

  BT device - I have the details as HDW - 22736-002 Rev 1 Ver 2 4509 (is that correct?)

  Apps & free space - nothing installed new device installation is not complete.
  Blackberry 4.6.1 Basic application
  Basque 4.6.1
  Galician 4.6.1
  softwqare system BlackBerry 4.6.1
  1.0.1.20 Application Center
  Attachment Service 4.6.1
  4.6.1 cards
  Messenger 4.6.0
  BrickBreaker 4.6.1
  browser 4.6.1
  documents to go 1.003.018
  configuration of e-mail application 4.6.1
  help 4.6.1
  Klondike 1.4.8
  4.6.1 Memopad
  password keeper 4.6.1
  Phone 4.6.1
  Sudoku 1.0.11
  4.6.1 tasks
  King of hold'em Texas 2.3.0
  Word Mole 4.6.1

  1 is the news provider's SIM card?

  Old to another device?

  2. do not place you a memory card in the camera?

  New media card?

  or from another device? What device?

• Satellite 1800-712 does not start with the new HARD drive

  Hello world.

  I am currently trying to install a new HARD drive in my notebook of 1800-712.
  I'm having a few trubbles as my Satellite won't start with my new HARD drive.

  I upgraded my BIOS to the latest version.
  The new HARD drive is a 40 GB Samsung.

  Any suggestions on what I need to do to make it all works?

  THX, Philippe

  Hello

  This device was shipped with 20 GB HARD drive.
  You again is 40 GB.
  I guess that the BIOS does not recognize the HARD drive because of the size.

• Satellite Pro 460 does not start with the new drive in

  I recently received a Satellite Pro 460, but he had no hard drive.
  It starts great without a disc in but as soon as I put a new hard drive in it does not start.

  I thought that it might be again a hard drive, so I pulled out my old Toshiba Satellite with my old drive to work, and yet, it does not start.

  Someone has any ideas why this is and what I can do about it

  I think that you can not do much. Satellite pro 460 CDT, for example, comes with 2 GB of HARD drive. If you try to get it work with similar HDD without success, it may be defective IDE port on the motherboard.

  What HARD drive you are trying to use on this good old classic?

• Computer does not start after installing new graphics card

  HP-envy h8-1503
  I7 - 3770 k 3.5 GHZ
  10 GB of Ram
  Windows 8.1
  
  I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

  I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

• C870-19(r) satellite does not start with the new SSD

  Hello

  I will update the Toshiba Satellite C870 19(r) with a Pro 840 Samsung SSD, but it does not start.

  He said: not found system.

  Post edited by: joch333n

  None found system means that there is no system installed on the SSD drive...

  What you trying to do?
  You start from a disk in order to install the new system?

  In this case, you should disable startup secure in the BIOS.
  I also recommend moving from UEFI mode MSC!

• Windows 7 does not start with the new msi motherboard

  Yesterday, I bought a new motherboard, processor and 8g of ram in my computer. After all what adjustment and replacement of my old motherboard with the new, I started my computer to find that Windows 7 unbootable not. Instead of windows 7, I get the screen click on BIOS II (2). The configuration screen allows me to launch Winki but not Windows 7 because it was not found. The motherboard came with a utility disk drivers msi and AMD chipset which, when inserted in my hard disk, loads up to Winki. This version of windows 7 (Home Premium 64-bit) came pre-installed with my old mother/computer(Thus, I do not have the windows 7 installation disk) card. Is there a way I need to activate Windows 7 on my new motherboard?

  Hello

  Well, you have some problems. First of all, with a new motherboard you need a new copy of Windows - not only the DVD, but a whole new product key must be purchased. It's just the terms of the license: a new motherboard is equivalent to a new computer, and each computer must have its own copy of Windows.

  So where you buy your copy of Windows 7, I would make sure that it came with a DVD image. Otherwise, you can tell us which version of Windows 7 you (will) actually buy, and we can send you a link to the copy of the DVD for this version of Windows 7.

  To purchase a copy of Windows 7 you can check Newegg.com, here: http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&DEPA=0&Order=BESTMATCH&Description=windows+7&N=-1&isNodeId=1 .

  I hope that answers your question.

  Kind regards

  BearPup

• Satellite L30 10Y does not start with the new RAM modules

  Hello
  regged just with this forum I have a problem to upgrade memory.

  I read through a few problems of memory here and all users that it is a problem of memory comaptible. I got Hynix 512 MB RAM in my laptop and I bought 2 x 1 GB memory Hynix these two are match sticks to the installed memory, but when I installed my laptop wouldn't boot at all. It would only boot if I had a stick in both.

  I tried to switch ports top and btm and even when a stick was installed it says in XP, Vista and Windows 7 (yes I tried all systems) 896 MB of available space. I even tried to use my other Hynix stick, but he won't start and showed more stick of 1 GB (896 MB usable in Windows 7). After reading all the threads I wonder if it is a hardware failure or is there a fix in the world of Toshiba or perhaps in the world of Toshiba, the L series is almost obsolete and not worth to help people who unwittingly bought their goods.

  I apologize for being slightly down on Toshiba but a laptop that shows what he can work and is not a company should hold his hand up and say that Yes, there is a fault and help deal with the problem.

  You see 896 MB, because the rest is reserved for VRAM for graphics card.

  Sometimes RAM may simply be incompatible, because of incompatibilities of calendar or RAM chip/controller design differences.

  What speed and timings is your original RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  What speed and timings is your new RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  You can display this information using a utility called CPU - Z
  http://www.CPUID.com/cpuz.php

• Inspiron 530 Win XP Home does not start with the TrendNet wireless card

  I just received 5/1 a refurbished Inspiron 530 530 Mini-Tower desktop: Intel Core 2 Quad processor Q6600 (8 MB L2 cache, 2.4 GHz, 1066FSB) Genuine Windows XP Home Edition. The PC didn't have any LAN card and I intend to use a working adapter TrendNet (COMPUSA) 54 Mbps Wireless G PCI I used very well with my old 4300 Dim run also Win XP Home. However, after that I booted up the new PC with the first series, I stopped him. I then opened and installed the card wireless in one of the 2 empty PCI slots. When I turned on the PC, surprise! The PC wouldn't start - it kept beeping with the glowing orange of front power button and turn off every two seconds, I then read the Inspiron 530 manual means that the motherboard has detected an error. Hello. I checked.

  I searched other posts in this forum and I've seen a few references to the boot configuration verification. However, installation of starting my PC doesn't have an option related to the wireless adapter.

  Someone help me please fix this error. I intend to reconnect the card on my old PC wireless again and start just to prove that the card is always good. I only removed a card video of him and the rest of the asis. (I've not carpet in my house is that reduces my chances to have fried the card when you remove or install.) I also touch the chassis of the PC before doing anything.)

  
  

• SMU 8108 does not start with the new hard drive

  Hello

  I am currently using SMU 8108 with SMU-1062 q.

  The previous record was borken, so I had to install a new hard drive.

  The new hard drive is fommatted as NTFS format, and it is currently mounted on 8108.

  Unfortunately, I don't have recovery disk available to the general public so I am trying to install Windows 7 on a blank hard drive.

  When you start, the LED OK PWK light is all the time, orange DRIVE LED turns on for a few seconds only when I turn on the switch.

  LabVIEW RT switches are all off, I cleared CMOS several times to the Board of Directors, but the screen does not show anything.

  I tried to use my DVI monitor with any other device as well, and it worked, so there is no problem with the monitor.

  In addition, I tried to go in window safe mode by pressing F8 or Del it didn't work, so I can't see anything on the screen when his kick upward.

  I tried to put a lot of information I can it will be very appreciated if you can help me with this problem please.

  You said that you can't in Windows safe mode, you have installed Windows on the hard drive?  Are you able to get into the BIOS of the controller?

  If you are not able to access the BIOS for the controller, it may be due to bad RAM.  If you are uncomfortable installing RAM and you have a few extra laptop RAM of the same type (I think it's the DDR3 for your controller) laying around, you can try to replace the RAM.

  Was your hard drive damaged through certain events, or it just stop working?

• C55-A-1MW satellite does not start with the new RAM inserted

  Hey.

  I hope to find someone who can help me... I bought ram memories and tried 4 different memories in my C55 A 1MW Satellite. But each card RAM I have insert makes the computer cannot start... It lights just to stop again.

  Is there a compatibility issue or anything like that? I used 2 different aData Ram extensions cars, 1 1 and 4 GB 2 GB. the 4 GB card was 1333 mhz and was 2 GB 1600 mhz card. and I tried 2 corsair 4 GB 1600 mhz different cards.

  Is this something that makes only able to expand RAM with Toshibas own memories or is the second cardslot for broken RAM memory?

  As I see you use RAM modules with different specifications. Your problem is certainly of RAM compatibility and you must use the RAM modules with the same specifications.
  According to specification of laptop there are 4 slots of memory and laptop can handle up to 32 GB of RAM.

  The compatible RAM modules are:
  4 GB DDR3L-1600-PA5104U-1M4G
  8 GB DDR3L-1600-PA5104U-1M8G

  Of course, you can use modules from other manufacturers, but please do not use some cheap products. I can recommend the use of Kingston memory modules.