Download ACL for VPN users. ACS 4.1 & 1841 router

Similar Questions

• Is there a website similar to the old Central stock Adobe, where individuals would download actions for other users to download?

  Is there a website similar to the old Central stock Adobe, where individuals would download actions for other users to download?

  You should probably ask in the forum for the specific program

  If you start the https://forums.adobe.com/welcome Forums Index

  You will be able to select a forum for the specific Adobe products you use

  Click on the symbol "arrow down" on the right (where it says all communities) to open the drop-down list and scroll

• Downloadable ACLs for users of VPN

  Hello

  I replaced the old pix with ASA (7.2). There were groups configured for the remote VPN users authenticated through the ACS and ACS download a specific ACL for each group to the PIX. After the replacement, users cannot establish the VPN connection. After troubleshooting, I discovered that the downloadable ACLs were not working very well. When I disabled this option the established tunnel. When I get back to the old pix with the same configuration, it works very well with downloadable ACL option. I opened a TAC case and he said the v3.0 ACS (I) are not compatible with the ASA. He did not really convince me and he asked to try to use the option to pair AV. I tried option pair AV with ASA and it did not work also. can you please advice.

  Hello

  Check out this point,

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCef21184

  In addition, 3.0 is very old, and I guess that in this version, we have "Downloadable PIX ACL" and not "downloadable IP ACL", on ASA download able ACL will work but with "Downloadable IP ACL" but not with "Downloadable PIX ACL".

  Kind regards

  Prem

• Downloadable ACLs for users?

  Hi all

  5.4 ACS, I need ACL customized for users.

  My scenario:

  There is a way to use some "downloadable ACL" profile of permission but I want to set specific ACLs for some exceptions. For example: the user A and user B obtain permission profile 'X '. But user B is not allowed to access a host. This 'refusal rule' I will configure with custom in the internal user store attributes.

  Is this possible? How can I implement this rule?

  Best regards

  Stefan

  Hello

  You can do this by following these steps:

  1. define a user attribute of Dictionary defined under the Administration of the system > dictionary > identity > internal users call him what you want and make sure that the value is a string

  2. create the DACL in the objects of the Authority appointed under section of the political elements

  3. under the user account you will see now one filed for the dictionary name you call in step 1, make sure that the domain is the DACL, that you created in step 2

  4. create your dynamic authorization under "common tasks" defined profile as the decline of the low DACL select internal users and set the value to the attribute that you created in step 1.

  5 card authorization policy to the access policy using the conditions that will give you these results.

  6 test and you should have what you are looking for.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• ACS and download ACL for multiple clients-AAA

  Hello!

  I need to know if it is possible to download ACL on the DACL device that is not a part of the conversation of RADIUS? In other words, I have a user who needs access to certain resources and attempts to connect to the network via PIX1. I need to authenicate it by ACS and download ACL PIX1 and (attention) PIX2 also (some firewalls upstream). Is it possible to do?

  I don't think that you can do. As you mentioned that the other PIX has no Radius configuration. And you can push only DACL of the Radius on the PIX server, she asks, not in any other PIX.

  And I'm not aware of any mechanism or feature, which allows you to transfer the downloaded ACL of one PIX to another.

  Kind regards

  Prem

• Dynamic ACL for Radius outer (ACS 5.3) accounts

  We have a Cisco ACS 5.2 server that queries another server radius for some AnyConnect VPN connections. We already use for some users dynamic access lists in the user Interal identity store. We would like to link in a list of dynamic access to users in the external database, based on the username passed back from the external radius server. We run ACS 5.3.0.40. Is it possible to do?

  [5.3 running and use AD then suggests to install the latest patch 5.3]

  Ok. Suppose attribute is in AD and called DACL. then proceed as follows

  1) go to

  Users and identity stores > external identity stores > Active Directory

  and select the tab "Directory attributes.

  (2) add the attribute named list DACL and save changes

  (3) build the authorization profile which will return the DACL

  Reach

  Elements of strategy > authorization and permissions > network > permission profiles > create

  in tab "Common tasks", select "Dynamic" for downloadable ACL name

  then select "AD - AD1" and the attribute selected in step 2

  and press on submit

  You know a profile authoirzation which will be dynamically retrieve the AD attribute and use the name of the downloadable ACS

  (4) further to the authorization policy, select this profile authoirzation

  for example:

  Access policies > access > by default access to network > permission

  Should be good to go

• ASA does not propagate any routes for VPN users

  Good afternoon

  I m a problem concerning the spread of the roads to authenticated VPN users through the asa tunnel-group.

  I have a VPN-users-pool where my users receive their IP address, and after authentication and the tunnel is established the idea is that the user get to the networks defined in the following ACL:

  access-list within the standard allow 10.1.0.0 255.255.0.0

  access-list within the standard allow 192.168.15.0 255.255.224.0

  Now, the problem is that, after the tunnel is set up the only way, that the user receives is the default route (which is not supposed to be sent). The user does not receive the roads specified in the ACL list above. It has not received the network mask and assumes one 8 netmask (given that the pool of network from where it receives the IP address is a class A network).

  Network routing works as expected (when I add the static routes directly to PC users, everything works OK). It s just the matter of the ASA do not spread the roads as it should.

  Here is my split tunneling settings:

  attributes of Group Policy DefaultRAGroup

  VPN-idle-timeout 1

  Protocol-tunnel-VPN l2tp ipsec

  disable the PFS

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  (...)

  attributes of Group Policy DfltGrpPolicy

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  (...)

  Any ideas?

  I have apreciate your help

  Best regards

  Just a question, I see:

  attributes of Group Policy DefaultRAGroup

  Protocol-tunnel-VPN l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  internal DefaultRAGroup_1 group strategy

  attributes of Group Policy DefaultRAGroup_1

  Split-tunnel-policy tunnelspecified

  It looks like your policy

  DefaultRAGroup_1 you set ACLs and the other doesn't seem to be for L2TP/IPSEC. How do you connect to the ASA, using L2TP/IPSEC or Cisco IPSEC client? In addition, if your users are devoted to this group policy:

  DefaultRAGroup_1 it looks like the acl is missing for the split tunneling

• Limit bandwidth for VPN users

  Hi guys,.

  I use ASA Version 8.2 (1), I want to limit vpn users to use less bandwidth of my Interlink to access something on the inside of the network

  example: source vpn pool

  Destn: inside the network

  Please let me know how to achieve this with QOS config.

  Hello

  Probably the best would be to match groups of tunnel.

  class-map TG1-best-effort 

  match tunnel-group Tunnel-Group-1 

  match flow ip destination-address 

  Then this traffic in police policy-map and apply the service policy to the external interface (since you want to traffic police from your home). You can also use the pool for vpn access lists.

  For more details, please see:

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/QoS.html

• Client VPN Cisco ASA 5505 Cisco 1841 router

  Hello. I'm doing a connection during a cisco vpn client and a vpn on one server asa 5505 behind a 1841 router (internet adsl2 + and NAT router).

  My topology is almost as follows

  customer - tunnel - 1841 - ASA - PC

  ASA is the endpoint vpn (outside interface) device. I forward udp port 500 and 4500 on my router to the ASA and the tunnel rises. I exempt nat'ting on the asa and the router to the IP in dhcp vpn pool. I can connect to my tunnel but I can't "see" anything in the internal network. I allowed all traffic from the outside inwards buy from the ip vpn pool and I still send packets through the tunnel and I get nothing. I take a look at the statistics on the vpn client and I 2597 bytes (ping traffic) and there are no bytes. Any idea?

  Where you you logged in when you took the "crypto ipsec to show his"? If this isn't the case then try again, also this option allows IPSEC over UDP 4500 and it is disabled, enable it.

  ISAKMP nat-traversal crypto

  Just enter the command as it is, then try to connect again after activation of this option and get the same result to see the.

• Download connection for VPN log

  Logging and diagnostics of the VPN connection are a total waste of time - even after clearing logs and the connection that once, there are tens of thousands of lines of newspapers. Diagnose insists, of course, that everything is fine. By clicking Help, takes you as usual, a totally independent place - I got 30 results for "troubleshooting." What has to do with VPN, I guess Microsoft could say.

  Can I get a simple log that shows the protocols and parameters that were considered along with the results? As the old modem component logs?

  Seems they were too advanced a feature for the Member States to implement in a bare back and compact OS like Win 7... / sarcasm

  PS That is him go with not being able to open the settings window? Or connect to two connections at the same time? Or check the status of the underlying network when connecting? Fever of the modal dialog again?

  If you watched to where newspapers to find errors?

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  You or the VPN server admins looked at the logs from the server using VPN?

  If it is a PPTP VPN connection?

  Don't forget you must forward/open the TCP 1723 Port through the firewall or the router, the server behind. The firewall or the router also need to be able to pass traffic GRE protocol 47. This is sometimes called PPTP pass through or VPN Pass Through or is configured automatically when the TCP 1723 Port is open on the firewall or the router.

  Test the VPN path using the PPTP Ping and VPN traffic sections on this page...

  http://TechNet.Microsoft.com/en-us/library/bb877965.aspx

  http://Windows.Microsoft.com/en-us/Windows7/why-am-I-having-problems-with-my-VPN-connection

  Troubleshooting VPN connections...

  http://blogs.technet.com/b/rrasblog/archive/2009/08/12/troubleshooting-common-VPN-related-errors.aspx

  Troubleshooting Vista VPN page that may be of little help...

  http://blogs.technet.com/b/rrasblog/archive/2007/04/08/troubleshooting-Vista-VPN-problems.aspx

  Additional help in TechNet Windows 7 Pro forums...

  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads

  .. .or the appropriate instance of Windows Server...

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• How to provide the download links for the users of the portal

  Hello
  
  I have several portlets (standard JSR168 built in Java with JDeveloper 11 g) that displays links to download files users.
  The files are stored in another system and obtained by calling a Web service.
  
  Which is the best way to provide these links to the user stays on the same page and get a dialog "save/open"? I have to develop a servelet process the request again?
  
  Thank you
  André Esteves

  Yes. You can write the processAction logic. The code in my previous post (content-disposition, attachment) will force the browser to open the file save/open dialog box. If you need example code to download the file, you can see this example .

• How to enable a download file for one user account controlled by Windows Live family safety?

  When my employee attempts to the weekly schedule on our Web site in the form of a. PDF file, the file download is blocked by Windows Live Family Safety. Block message says he must ask permission to download the file. When I go into parental control settings, under the supervision of the activity, I can see the file which was blocked, but I don't see an option to allow the download of the file.

  Hello

  The question you have posted is related to family and security and would be better suited to the Windows Live community. Please visit the link below to find a community that will support what ask you:

  http://www.windowslivehelp.com/product.aspx?ProductID=4

• IPSEC VPN between Pix 515E and 1841 router

  Hi all

  BACKGROUND

  We have implemented a site to site VPN IPSEC between a Pix 515E 8.0 operation (4) and an 1841 using static IP addresses at both ends. We used CCP on the router and the ASDM the pix to build initial tunnels. Now the site with the router is evolving into a dynamic IP address from the ISP so we have implemented dynamic DNS to update dynamic IP address.

  PROBLEM

  The problem is that ASDM will not allow us to set a domain as the address of peers, it will not accept an IP address. We believe that the solution will be to remove the static Crypto map and replace it with a dynamic Crypto map on the side of Pix. Our questions are simply; is this the best solution? can change us the original static list or is it better to delete and make a new dynamic encryption card? Y at - it a shortcut to change the config command-line? This is a real network, so just check it out before make us any changes on the live kit.

  Any help much appreciated.

  You don't have to change anything when the peer-address changes. The dynamic crypto map aims to take dynamic peer connections. The only thing to remember, is that only the dynamic peer can initiate the connection. And you reduce your security if you use Pre-Shared key that now you can use a generic-PSK character.

  As I remember, the PIX / ASA does not support the dynamic use of FQDNs for peer-resolution. This feature is supported in IOS.

  For a feature, it would be preferable to static IP addresses on both sides.

• Download ACL GBA 5.2 using authentication for 802. 1 x

  Hi all

  I configured ACS 5.2 for authentication authentication of 802. 1 x. It works as well, getting customers belong to their VLAN respective after a successful authentication.

  Now I want to assign downloadable ACLs for particular users can someone help me in the downloadable ACLs configuration GBA 5.2.

  Any feedback is much appreciated.

  Thanks in advance,

  Selva.

  Hi Selva,

  Based on that you want to assign the DACL? based on the user name? Group?... etc?

  This document will be useful for you:

  http://tiny.cc/ogrxvw

  ignore the part of the SAA. concentrate on the config of the ACS.

  The doc use ASA as the AAA client. The difference is that you use a switch. but the idea is the same.

  HTH

  Amjad

  Rating of useful answers is more useful to say "thank you".

• Doubt on the RA aaa using ACS 5.3 vpn user

  Hello

  I'm putting in place of the VPN on 8.4 ASA with 2 - VPNGp1 and VPNGp2. VPNGp1 groups users will access 1.2.3.0/24 and VPNGp2 users will have access to 5.6.7.0/24. User authentication will be done using RADIUS 5.3 ACS.

  On ASA, I configured pools VPN groups, ACL of VPN, IP, tunnel of groups and group for each group strategies.

  GBA, I created vpn-user1 and user2-vpn for each of the 2 groups.

  I don't know if some configurations more must be done on ASA and AC... Do I need to add new users - vpn-user1 and user2-vpn - on ASA, under each corresponding group policy, using the command political vpn-group?  Or I need to do something else on the ACS?

  Finally, how can I configure authorization and accounting for VPN users? I have to do this on GBA or ASA?

  Please advice.

  Thank you.

  Hello

  Authentication using radius aims to centralize user accounts and policies so that you will not have to configure these on the SAA. You must create a group of authentication servers that points to your ACS, then you will have to refer to this group of servers to your tunnel-group for user authentication queries will be forwarded to ACS for authentication. For accounting you will create an accounting server group and also assign to your tunnel group configuration.

  The GBA, you will need to create a network client that is ASA, and the shared secret will be the same. You create an element of authorization policy network who have the permission settings, or you can choose allowed access, which allows authentication succeed without any special authorization.

  You can debug the sessoin using crypto vpnclient 255 debugging to view the authentication stream.

  Using SSL vpn (anyconnect) for these sessions?

  Thank you

  Tarik Admani