Download the iso files tool part?

I have a laptop dv7 640 gig 2 years old and I got the imminent message "hard drive failure. So, I backed up the hard drive (8 DVDs) and make the recovery discs (6 DVD). I bought a new Seagate 500 gigs HDD and installed. I then started the recovery process.

Then, I got a message that says that my new hard drive is smaller than the original and will not proceed. I tried installs four different without success, to get a blank screen with the exception of the logo hp on the center of the screen and a Press esc to menu.

I read the advice to try downloading the iso file through dvd or usb. My question is: the directions speak using the w7 dvd/usb download tool. This part of tool of downloading the files? How do I get it on my first computer? I know it's probably easy, but it would be nice for me to get that clarified before proceeding to downloads.

THX.

Hello

As the error that you are experiencing is simply due to the fact that recovery disks will not properly install on a disk smaller than that they were created on, I just burn the ISO correct on a blank DVD and use it to run the installation - there is no need to create a bootable USB key, unless you have a problem with the optical drive of your laptop.

Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

An example of a COA label can be seen here.

You can create an installation disk yourself using another PC - just download the good Disk Image ( this must be the version exact same origin supplied with your laptop ) from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is here.  These Images are clean and a well respected source, however there are only limited versions available.

Windows 7 sp1-iso-official-32-bit-and-64-bit

Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

All pilots additional and the software, you may need can be found by entering your full model number or Nr here.

Kind regards

DP - K

Tags: Notebooks

Similar Questions

  • Cannot download the iso file of the web site windows like this windows dvd is false and not original

    Original title: download windows 7 pro 64-bit

    Hello

    I have buy windows 7 pro whit this product key *-* - CHDW4 - JCYBD-W4FXT with windows dvd

    but when I install and activate, I see cela windows dvd is false and not original

    I can't redownload iso file of windows web site

    Please send me redownload link.

    Thank you

    better compliance

    For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

    It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

    Given that this option is no longer available, what are your options? See the article for more details:

    How to: What are my options for Windows 7 reinstall media?

    Make sure you scroll down and read the section:

    What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  • I installed the download tool usb/dvd windows 7, but after you have selected the iso file when I insert the USB stick and refrecing, it does show that "no usb drive compatible' what is the problem with my USB

    I installed the download tool usb/dvd windows 7, but after you have selected the iso file when I insert the USB stick and refrecing, it does show that "no usb drive compatible' what is the problem with my USB

    I have sandisk cruzer blade USB key

    Hi Rohit,

    Thanks for posting your query in Microsoft Community Forum. I understand that your USB drive is having problems of compatibility with your computer, but I would like to learn more about the issue in order to provide you with better assistance.

    1. You did it any significant hardware or change software on the computer before this problem?
    2. When do you get exactly the error message?
    3. Have you tried to connect to any other computer on this flash drives?
    4. Your USB key works on other computers or have you tried to connect to different USB ports on this computer?
    5. Is the pen drive getting detected in the case or you are able to access the drive folder in the window of the computer ?

    The question may arise if the currently loaded USB driver has become unstable or damaged, or if your PC requires an update for problems that could conflict with a device USB and Windows. This can also occur if your USB controllers may have become unstable or corrupt. So, I would suggest trying the following steps and check if the problem persists.

    Method 1:

    Please try the fixit (s) provided below which will help you solve common problems associated with devices and USB ports.

    If method 1 does not work, try Method 2.

    Method 2:

    Remove and reinstall all USB controllers.

    1. Open Manager devices by clicking the Start button, click Control Panel, click system and security, and then, under System, clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
    2. In the list of the categories of equipment, locate and expand Bus USB controllers.
    3. Right-click every device under the Bus USB controllers node and then click Uninstall to remove them one at a time.
    4. Restart the computer and let the USB controllers get reinstalled.

    Plug in the removable USB device and test to make sure that the problem is solved.

    If the problem persists, go to method 3.

    Method 3:

    This method will install the latest drivers from device to your USB device.

    1. Click the Start button, type Windows Update in the search box, and then click Windows Update in the results pane.
    2. Click find updates. When the scan finished, click optional review updates.
    3. Click the check box next to the update, and then click install updates.
    4. If you are prompted, read the license agreement, then click I agree.
    5. Follow the instructions on the screen to download and install updates.
    6. If you are prompted, restart your computer.

    More information: Update a hardware driver that is not working properly

    Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

  • Downloaded SP3 of XP on a USB to update XP computer without internet connection, computer, failed to read the iso file?

    I downloaded the SP3 of XP on a USB to update an XP computer that is not connected to the internet.  The computer cannot read the file, any suggestions on a download that will help you... the file is a. ISO file

    Hello

    Install SP3 by downloading and running from...

    http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=24

    You can ignore the text which says that it is for network installations and also ignore the text informing Windows/Microsoft Update If a single update of a PC.

    It is an executable file (.exe) that must just run and install, i.e., it is not an iso file that will be used to create a CD which included the executable.

    Just like the iso file, it can be saved to a Flash DRIVE on another PC before running on the PC to update.

    So try and get up-to-date with the Windows updates.

    Tricky

  • Where can I download the ISO of Windows 7 Proffessional 64-bit file

    I have a genuine key for Windows 7 Proffessional 64 bit. but I don't have a configuration file / ISO.

    Where can I download the ISO of Windows 7 Proffessional 64-bit file? Please help me

    Enter the key and after validation, you will be offered the ISO:

    https://www.Microsoft.com/en-in/software-download/Windows7

    See also:

    http://answers.Microsoft.com/en-us/Windows/wiki/Windows_7-update/how-to-what-are-my-options-for-obtaining-Windows-7/528163c1-0b2e-4AD2-a26d-7112851d1dc2

    It will be useful.

  • I'm trying to download the 2 files for CS3 Master Collection ADBESTAMCS3_ESD1_WWE.7z tried several machines and settings.  He seems to have almost done so failing shows and. part.

    I'm trying to download the 2 files for CS3 Master Collection ADBESTAMCS3_ESD1_WWE.7z tried several machines and settings.  He seems to have almost done so failing shows and. part.

    Use another browser or another connection (cable), a download manager.

  • Download the ISO from Microsoft files

    After that my choice of the language of the key (Windows7) audit has only Korean in the drop down menu.

    What's wrong?

    Many users report the same problem * with the recovery of the MS. software page  One of them said that they clicked on a link on this page and, once support persistent, received a temporary link for download the ISO English language that they need.

    * Just search this forum Korean and you will see a lot of these reports.

  • Cannot download the media creation tool. exe

    Windows 7 Ultimate, Windows 10 download attempt.  So far without success.  Cannot download MediaCreationTool.exe.  Message says simply "could not be downloaded.  Administrator disabled?  Suggestions?  Thank you

    Use Microsoft Techbench to download and create a bootable copy:

    Go to: https://www.microsoft.com/en-us/software-download/techbench

    Before you start

    Make sure you have:

    • An internet connection (internet service provider fees may apply).
    • Enough data storage available on a computer, USB or external drive for ISO downloads and scripts.
    • 16 GB or larger USB for use on systems of disk space is low.
    • Micro-USB adapter for the use of media on shelves.

    Click in the list box select edition, then choose your edition, 10 Windows contains two installation files for the home and professional allowing you to select the edition during installation. What to choose, click on confirm and wait while the option is validated. Do not refresh the page. If you are running Windows 8.1 with edition of Bing, please make sure that you select Windows 10 SL.

    Only select Windows 10 N if you live in Europe, please note it does not include Windows Media Player.

    Click in the list box and then select your language and then click on validate and wait while the option is validated. Do not refresh the page.

    Click on your of desired architecture and then click Save.

    Follow the instructions to use the image for the USB/DVD tool Microsoft .iso , Rufus or file the Image Disk burning utility in Windows 7 or a later version to prepare the. ISO file. You can also mount the. ISO in Windows 8 or later, perform an upgrade.

    Prepare the file ISO for Windows 10

    After downloading the ISO of Windows 10, you must prepare, it is particularly important for users of Windows 7...

    After graduating the .iso file, you can use the built-in Image disc burning tool or Microsoft .iso to USB/DVD tool to create a bootable DVD or USB (requires a blank DVD or USB flash to at least 4 GB key).

    After downloading the. ISO file, right click and click burn disc image

    Insert a blank DVD

    Click on burn

    Windows 8/8.1 users can mount the. ISO file and start the upgrade automatically. More here

    Important:

    If you create a USB startup key, make sure the USB is first in the FAT32 format.

    Connect the USB

    Open Computer

    Click with the right button on USB

    Click on Format

    Make sure that FAT32 is selected as the file system.

    For UEFI systems based

    If your computer is UEFI, they are normally the systems that come pre-loaded with Windows 8 or later, you need prepare the ISO for such a configuration file or you will receive an error during installation. The USB key must be formatted in FAT32 and use the GPT partitioning scheme. To do this, you must use Rufus, a small tool that you can download for free.

    Rufus - credit: Pete bastard/Akeo

    After installing Rufus:

    • Launch it
    • Select the ISO Image
    • Point to the file ISO for Windows 10
    • Check create a disk bootable using
    • Select GPT partitioning to EUFI firmware as the Partition scheme
    • Choose FAT32 NOT NTFS as file system
    • Make sure that your USB in the device list
    • Click Start
    • Close when you are finished

    You can then try the upgrade:

    Task of pre-required

    When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

    then

    • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
    • Reboot several times, and then try again.
    • Disable the general USB peripherals (for example - smart card reader).
    • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
    • Perform a clean boot, restart, and then try again.
    • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
    • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
    • If this does not work, try using the. ISO file to upgrade if possible.
    • If you are connected to a domain, go to a local account.
    • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).
  • How to convert dvd win7 with the ISO on my office installation files so that I can again use the iso file to make an installation key bootable win for my net book which has no dvd player.

    I bought a proffessional win7 genuine dvd of microsoft I received today. the dvd has no iso file but only installation files. I need to install win 7 on my dell inspiron mini 1018 10 net accounting that only has usb ports and no dvd support. So I want to use a microsoft tool (if it is possible to avoid 3rd party tools) and firstly convert the files in the bootable dvd into an iso file on my desktop which has the dvd player. so I want to use the iso file and use the windows download dvd tool from microsoft to make a bootable USB key and use it to install win 7 on my netbook usb ports. I need urgent links to the microsoft tool if it is available or any reliable free tool to convert DVDs to iso. Help, please

    You can use iSO recorder:

    ISO Recorder v3

  • Unable to download the ISO of Windows 8 on the official website of WIndows

    Hello

    I have a legitimate key for Windows 8, but I can't download Windows 8 iso from windows site.

    Whenever I try to download it gives me the error 'internet connection '. I tried it on my laptop, my friend laptop, office. I also try deleting the temporary files created for windows download. But the same error is coming for my key of Windows in the world. Can you please help me solve the ad that allows me to download the iso of legit windows 8.

    Here is the screenshot of error.

    PS: - I bought "Windows 8 pro" and subsequently update Windows 8.1.

    Hi Shilpi,

    It seems that this issue is a large part of the area of support for ESD. I suggest you to contact support from the EDD for more information.

    ESD team contacts list is located here:

    http://support.Microsoft.com/GP/ESD-support-phone-numbers

    You can also refer to the suggestion of Arya S Asok and Bill Fill in the following link and check if it helps.

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/we-cant-connect-right-now-check-your-Internet/ca433e12-5128-4159-9193-ed94d166de59

    I hope this helps.

    Please report if the problem persists and we will be happy to help you further.

  • Why can't I managed to install the iso file in my USB? I've tried different usb and hard drives and disassembled a lot or time usb but when, it comes up with an error copying the files on and it stops loading? What should I do?

    Why am I unable to download and copy iso files that need to go into the USB drive, it always comes up with an error when copying the installation files and none of the solutions have worked (some of the things I've tried are different from the USB, disassemble and repeat the download process windows files)

    You cannot use a simple USB as a source and destination. You must copy the ISO file (it's a single file, not the full installer) in your Documents folder and then run BCA to create a USB installation program. 2015 macs do not create a USB installation program.

    Please visit https://help.apple.com/bootcamp/assistant/6.0/ .

  • Bootcamp does not accept the iso file

    I try my macbook pro for windows 8.1 El Capitan Bootcamp and I have the iso file you downloaded here:https://www.microsoft.com/en-us/software-download/windows8ISO but Deputy bootcamps does not accept it. It is said that the iso file is not windows 7 or higher. I tried to use windows iso 10 too, but it says the same thing. Can someone help me pleas with this error. Thank you.

    You can check the MD5sum of your ISO 64 bit Windows 8.1? Use the command highlighted in OS x Terminal in the directory where your ISO.

    OpenSSL md5 Win8.1_English_x64.iso

    MD5 (WIN8.1_English_x64. ISO) = e0d4594e56c0545d379340e0db9519a5

  • Is my Windows my product key license? Also, if I want to download the iso of Windows 7 yes I need to buy a license/product key of Windows 7?

    Is my Windows my product key license? Also, if I want to download the iso of Windows 7 yes I need to buy a license/product key of Windows 7? Or my Windows 10 will work?

    Your license is the product key.

    You don't need to buy a license if you already have a product key.

    Step 1: Download a copy of Windows 7:

    For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

    It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

    Given that this option is no longer available, what are your options? See the article for more details:

    How to: What are my options for Windows 7 reinstall media?

    Make sure you scroll down and read the section:

    What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

    Step 2: Perform a custom installation, see Windows 7 section of the following article how to perform a custom installation:

    How to: perform a customized Windows installation

    Step 3:

    http://techingiteasy.WordPress.com/2012/04/13/how-to-activate-Windows-7-OEM-license-using-a-retail-disc/

    You can also use your Windows 7 product key to install and activate Windows 10:

    How to install and activate Windows 10 using your Windows 7 or Windows 8 product key

    If you have problems with activation:

    Activate your Windows 10 license with Microsoft Chat support

  • Lost my copy and I tried to download the iso from the Microsoft web site, but my product key will not validate, pass this message: we had a problem with the validation query

    Original title: error Windows 7 installation files

    I bought a copy of Windows 7 at Tiger Direct on 22/05/2014.  I lost my copy and I tried to download the iso from the Microsoft web site, but my product key is not valid.  I get this error message

    We had a problem with the request for approval.

    FAQ

    See for other directions:

    http://answers.Microsoft.com/en-us/Windows/wiki/Windows_7-update/how-to-what-are-my-options-for-obtaining-Windows-7/528163c1-0b2e-4AD2-a26d-7112851d1dc2

  • I lost my CD windows 7 Home Basic, can you provide me with the ISO file

    I'm on PC assembled with i3 1st gen 3.07 GHZ processor Intel with 4 GB of RAM.

    I put in Windows 7 Home Basic and have the activation key for the same thing but lost my CD. Can you provide me with the ISO files approved for her.

    I had tried a lot of ISO file, but none worked mainly for basic Stater of Windows and home proplary. Is the ISO file or my PC is not supported with Home basic.

    If Yes, then what is the solution.

    Some of the links that I tried are

    https://***.to/Windows-7-all-in-one-pre-activated-excellent-t7661549.html

    http://getintopc.com/softwares/operating-systems/Windows-7-Home-Basic-free-download-ISO-32-bit-64-bit/

    Please help as soon as possible.

    For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

    It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

    Given that this option is no longer available, what are your options? See the article for more details:

    How to: What are my options for Windows 7 reinstall media?

Maybe you are looking for