Drive DVD TS-L632D not write & burning CD and DVD
I have a portable Hassee W230r with a tsst ts-l632h DVGW DVD player.
Recently, the DVD drive is not burning DVDs or write data on DVD discs.
It allows to write DVD OK, but now after it said burning was a success, there's nothing on the disc.
Sometimes it sucessfully writes CD, other times it fails, especially when creating audio CDs and t plays most of the DVD (although sometimes he jumps about 5 minutes before you load the CD and DVD)
I can't find a driver for it, and to be honest Im not sure of time I should be using a driver, or "firmware".
I have dual boot XP and Ubuntu Hardy 8.04. Ubuntu Hardy comes with its own drivers for Hardware, but I get the same problems using Ubuntu on Windows. Which made me think that it was a hardware problem.
The laptop is 6 months old.
Thanks in advance for any help.
> I have a laptop of Hassee W230r
It is a forum of Toshiba and discuss us problems on Toshiba laptops.
Your laptop is not a Toshiba machine!
I recommend to ask support from the laptop manufacturer
Good luck
Tags: Toshiba
Similar Questions
-
How about you post that again without commas and maybe then I'll read it?
-
CD/DVD RW drive bed but will not write...
I use Windows XP and use the disk drive: Optiarc DVD RW AD - 7530A. Under "Properties" is the State of the device "working properly" and he plays both CDs and DVDs. However, it will not write. I tried several software programs, including windows Media Player. When I right click on the driver, there is a recording tab.
The drive appears to work at first, but it can progress remains at 0% and the drive will continue as he does something, but it's not. If I try to cancel the burning using buttons in the software, nothing will happen. It will freeze my computer. The Task Manager will not work, and my only option is to keep the off button on the laptop until it dies. When I turn it back on, a small window pops up saying files are waiting to be transferred to disk, click on the bubble to continue (or something like that). If I click on it, then I see the blue screen of death and the computer shuts down.He also seems to have done something for my Explorer, it freezes too (I'm on Safari now)may be a full AV scan VIRUS.
-
CD/DVD drive reads but does not write.
I run XP multimedia.
When the optical drive no longer works, I ran malware controls, then Mats_Run.dvd.exe.
"I had to choose and choose fix' reading discs ' which it did.
"" Write function did not work so I ran /Mats_Run.dvd.exe again with the ' writing difficulty ' option.
Still, it reads but does not write.
I installed an external burner and repeated the above; same result.
When I boot with Vista, the two burners work perfectly.
Details of virus removal
Provided by: Malke - MS MVP:
http://www.elephantboycomputers.com/page2.html#Removing_MalwareAlso:
Unexplained computer behavior may be caused by deceptive software
http://support.Microsoft.com/kb/827315Never be afraid to ask. This forum has some of the best people in the world to help.
-
I try to install the codec for the opening of "cr2" RAW files, and a message appears until the installation is complete. It is said:
Could not write value to key Progid
\SOFTWARE\Microsoft\Windows\Current Version\Explorer\FileExts\.sr2\userChoice. Check that you have enough measure to this key, or contact your support team.
I am the "personal support" and I don't have any idea.
I try try again and ignore and they have all two 'ignore' me. Down load always freezes at about 75%, and I have to cancel.
Please stop before I try again!
The answer seems to be on the forum. Try here:
-
DVD-ROM drive works, but does not appear in 'Computer' and discs can be played
I totally messed up my DVD - ROM drive. After graduating the famous blue screen of death once yesterday and once today, I thought that my PC settings reset would fix the problem. Then, I pressed F2 when my computer starts and resets all settings. Unforunately, this is something serious to my DVD - ROM drive. Initially, it did not work, so I opened my computer and somehow got it works. But now, it does not detect the disks I insert in there. I get the message "no DVD - ROM drive found."
Anyone know if it's fixable? I hope I don't have to take my computer somewhere for repair. Unforunately, I don't know the make or model of the hard drive. My the PC features that I think are important are listed below.
I watch this thread, so if I'm on my PC I will be notified by email of responses.
Characteristics of the computer:
Model: Dell Dimension E520
OS: Windows Vista Home Premium (32 bit)
Video card: ATI Radeon HD 2400 PROMessage edited by Jesant13 on 27/06/2008 20:47
-
Hello:
DVD players, both came with the PC and MSI DVD - Rom I bought through the Internet works ONLY for playback of CD - r and DVD - r, but the two do NOT write/burn brand new DVD and CD - R, popping up in the middle of the screen,... Please insert the blank in the E floppy when I actually inserted in the DVD drive.
I have uninstall and rebooted the PC, in the hope that readers DVD works OK,... but nothing helps.
Wonder if the registry damaged for DVD player, or what other problems causing this problem?
Any help on this would be greatly appreciated.
Hello
Have you checked if the CD/DVD drive you purchased is a recordable disc? If this is the case, there should be an indication (e.g., CD-RW/DVD-RW). You can also check for the indication Device Manager.
If you have confirmed that it is indeed able to write on the discs, then try to activate the IMAPI. To do this please see the instructions below.
1. click on start
2. click on run
3 type "services.msc" (without the quotes)
4. in the window that opens, you select IMAPI
5. right-click on it and select "Properties".
6 start the services.
-
Satego X 200 - 21 d: drive DVD TS-L632D is not read and burn DVD-R DL
Hallo,
I have problems with my DVD SATEGO X 200 - 21 d
TS-L632D read a burn only DVD-R DL discs.
I contacted Toshiba support via e-mail and asked
for a new disk firmware, but the answer did not solve my problem.There are only updates in the download area of toshiba,
but not for my car model. I can send my laptop
for the money to a service partner, to check this problem.I do not understand this! I bought a laptop upscale
for 1,700 EUROS and there is no support for the update of the firmware
available to solve problems with newer drives?If I get this problem in the WEB, there is an a large number of
questions and problems with playback and engraving
Discs DVD-R DL with this drive model!
How is it possible?I hope for some advice to get an update of the firmware player
to solve the problems of reading and writing DVD - R DL discs.Janni J. Gettings of Germany
Hello
I found the update of the firmware on the European driver Toshiba page!
Satego X 200 - 21 d seems to belong to the PSPBEE and the Toshiba page provides the update of the firmware to TO02.
It s for the TS-L632 reader.But generally not all CD or DVD of all manufacturers is fully supported.
My knowledge of the user manual should provide a details and info on compatible and tested media.
Using recommended media, you can be sure they will be compatible and will work 100%.Greetings
-
DVD drive does not write - Satellite M40X-175
Im having a problem with my dvd. I tried to burn my movies, music and my files on a dvdr or cdr, I tried DVD - RW and CD - RW but I do it every time gives error "d:\ is not accessible incorrect function". but when I try to watch a dvd movie or use my music cd, it does not work. He reads. Does this mean that my dvd drive cannot be read and not write?
[Edited by: admin on 4 February 06 20:23]
Hello
Satellite M40X sounds new enough to have CDs of feature writing. Seems to me a HW question but you can try:
1 - Clean the blank CD with a cloth dry
2 - blow to the goal and do not forget that there is no dust
3. you can uninstall the driver from
-> Panel-> system-> hardware-> Device Manager-> DVD - RAM-> (right click) properties--> driver uninstall-> restarting your laptop.If they do not contribute, you can contact a Toshiba authorized Service partner. You can find the one nearest to http://217.45.123.236/toshiba/resellerselector.nsf/WebServiceProv?OpenForm
-
Matshita DVD RAM UJ850s ATA optical drive will not read burned media, running Vista
* original title - CD/DVD unit read not "burned" cd *.
Hi, there are about 6 weeks, I had to do a recovery because a virus in my PC, the problem is that now the optical unit reads no CD, it reads 'original' CD, DVD (original and burned) but not burned CD specially those who have programs on them, could be a driver problem, but so far I have not been able to solve the problem , and I m not sure the original driver are in Sony's site, or any other Web site.
PS the thing Burns CD and they can be read after that that they were "closed".
I have a VAIO VGN-N330FH, running Vista Home Basic 32 bit (Spanish), the model is a Matshita DVD RAM UJ850s ATA Device.
Hello
You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
correctly.Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.
Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.
CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
tolerances. They may be delivered, but it is generally more economical to replace the disk.Several good info here:
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014===========================================
This troubleshooting could not help if there is alignment and/or wear issues however it
a shot.Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://Club.myce.com/F61/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
DVD drive will burn discs and not read the content
my dvd player will be only burn discs... any time I put in a cd of software or audio CDs, it won't let me veiw content... When I put in a cd of software says "Please insert the disk" and ejects the cd. When I put a CD audo (burned) it gives me just the ability to add files to a cd. thinking it was a problem with the drive its self, I bought an external dvd drive and it does the same thing. I can't understand why he won't let me see or install any content of a cd, any help or point in the right direction would be really useful thanks.
Hello
You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burn
and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.CD have a tolerance + - and you can read on the edge outside their tolerance. They
may be released but it is usually more economical to replace the disk.Several good info here:
http://Club.myce.com/Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014-----------------------------------------------------------------------
Try this troubleshooting:
Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitThe CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Hope these helps.
Rob - bicycle - Mark Twain said it is good. -
DVD drive does not write most of the time
Please, I would like to help here:
1: HL-DT-ST DVD-RAM GH22LS30 ATA Device "SATA".
This device well read no problem at all, but it well not write more then about 5% of a DVD and then he throws. With the help of the Super Multi Drive LG installation disc.2: cannot install: Microsoft SALIOU adapter
3: cannot install: Microsoft tity Tunneling adapter
4: cannot make a backup of the systemDETAILS: Windows 7 Ultimate
Processors = processors Dual Core AMD (tm) 4450e
Processors = processors Dual Core AMD (tm) 4450e
3 GB of Kingston
2 HD 1 TB every time good job of SATA.Thank you in advance for any help you can
The DVD player may require cleaning with a cheap kit that you can buy at any place that sells computers. I had good experience with my readers DVD LG, not to mention my LG TV that I love. One thing you can do when you are trying to burn DVDs would be to reduce the burn speed. I usually use the software Roxio or Nero to burn DVDs - they have always worked well for me.
Relative to the backup, use one of these big drives for backup and you get a good 3rd party backup program like the free Easeus todo backup free of charge that you can download from
http://www.todo-backup.com/products/home/free-backup-software.htm . Better yet, you get an external hard drive. You can buy these days 1.5 to ones for about $90.
Good luck.
-
LightScribe dvd writer/burner does not
I have a PC HP Pavilion Media Center with windows 64 Bit the CDRom 8Pro OS, it works very well, but the dvd burner does not work. Massage appears asking me to put a cd in the unit, even if there is already in the drive. Device Manager acknowledges the two discs and a convenience store can not detect potential failures. Information System also recognizes readers. The names of drive information dvd writer the C:\windows\system32\drivers\cdrom.sys drive as my system is 64 bit, this could be the problem and if so, how do I fix it?
Sorry, but the last I knew the Lightscribe technology was not Compatible with Windows 8.0/8.1. I don't know of anyone who has managed to get this working. Hope this helps and if you need any additional aid station and we will be happy to help you.
The above opinion is mine and mine nothing and does not necessarily reflect that of Microsoft, it's employees, or any other Member of this forum.
"When we try to take anything by itself, we find it hitched to everything else in the universe."-John Muir
If this has answered your message please mark as answer
-
CD/DVD-RW Drive does not write on Satellite Pro M75
Hello
Im having problems burning CD and DVD on the drive. I have some media in itunes (which i baught! also I have made a backup of the original!) and I want to put on a disc, so I make a new playlist as usual, then I put the disc in and then click on "Burn to CD" so I do... it burns a song, but she then said that there is an error. Also when I try to burn a video I have made through DIVx and happens to 1% and an error occurs. screwing of the disks.
Also when I try and format the DVD - RW with Sonic DLA thing - it gets to 5% and then it says: 'cannot continue because of the General faliour' which is also very annoying also.
What should I do? What is the hardware or software.
Thank you
Joly
Hello
is this error happening since you have this computer or from a specific point. Would be interesting when the problem started, maybe some software is defective drive and causes this error you have.
Please give some detailed comments and describe what you were doing in recent times with the machine and the fact that you have installed a software or something else.
Would appreciate some comments.
Welcome them
-
Problem with TSSTcorp TS-L632D TO04 CD/DVGW stoped burning CD and DVD
Hello world! The problem is basically just, he doesn't want to write/burn any cd/dvd brand more. He works wonders for little over a year and recently developed this problem. I'm sure that's not media brands I've tried with several. The problem with Nero, Alcohol120%, MagicISO, PowerISO, Burn4Free, regardless of what I am trying to burn data, audio, regular programs or images. Note that I am able to write with alcohol with success but there is in fact nothing on the CD and Nero burns the data also but fails to verify after the fact and gives an error. Writing on DVD R/RW is completely failed, creating coasters. Also the Player opens without reason and when he wants. I have laptop Toshiba A200 - 1 MB under original Vista Home Premium. Here's an error report, hopefully it'll help. Thanks and any assistance is much appreciated!
Windows Vista 6.0
IA32
WinAspi: -.NT-SPTI used
Nero Version: 9.2.6.100
Internal Version: 9, 2, 6, 100
(Nero Express)
Recorder:Version: TO04 - HA 1 YOUR 0 - 9.2.6.100
Adapter driver:HA 1
Drive buffer: 2048kB
Bus type: Via inquiry data
CD-ROM:Version: TO04 - HA 1 YOUR 0 - 9.2.6.100
Adapter driver:HA 1 = Scsi-device-map =.
= CDRom-Device-map =.
TSSTcorp CD/DVGW TS-L632D E: CdRom0
=======================AutoRun: 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) bytes
BUFE: 0
Physical memory: 2037 MB (2086276 KB)
Free physical memory: 864 MB (885052kB)
Memory used: 57%
QUERIES PFiles: 0x0
Global Bus type: default (0)
Control supported media: disabled (0)13.10.2009
CD-ROM (ISO)
02:27 A. Â? ? Â? #1 text 0 file SCSIPTICommands.cpp, line 452
LockMCN - completed successfully for IOCTL_STORAGE_MCN_CONTROL02:27 A. Â? ? Â? #2 text 0 file Isodoc.cpp, line 6940
ISO document burn settings
------------------------------------------
Determine maximum speed: TRUE
Simulate: FALSE
Write: TRUE
Finalize the CD: FAKE
Multisession: TRUE
Multisession type: Start multisession
Burning mode: TAO
Mode : 1
ISO level: 1 (Max. of 11 = 8 + 3 char)
Character set: ISO 9660
Joliet: TRUE
Allow pathdepth more than 8 directories: TRUE
Allow more than 255 characters in path: TRUE
Write ISO9660; 1 file extensions: TRUE02:27 A. Â? ? Â? #3 text 0 file Burncd.cpp, line 3257
TSSTcorp TS-L632D CD/DVGW
Super link activated02:27 A. Â? ? Â? #4 ISO9660GEN-11 file Geniso.cpp, line 3349
First address writeable = 0 (0x00000000)02:27 A. Â? ? Â? #5 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 0. Length: 2885-> 2883.02:27 A. Â? ? Â? #6 text 0 file Burncd.cpp, line 3587
Turn on Track-At-Once, using CD-R/RW media02:27 A. Â? ? Â? #7 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:27 A. Â? ? Â? #8 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:27 A. Â? ? Â? #9 text 0 File DlgWaitCD.cpp, line 294
Media in the drive type: unknown
Write speed more up/down CLV: 3 x / 1219560 x
Recorder min/max supported write speed: 4 x / 9226724 x02:27 A. Â? ? Â? #10 text 0 File DlgWaitCD.cpp, line 313
Last possible write address on media: 359846
Last address to be written: 288402:27 A. Â? ? Â? #11 text 0 File DlgWaitCD.cpp, line 325
Write in overburning mode: No. (enabled: CD)02:27 A. Â? ? Â? #12 text 0 File DlgWaitCD.cpp, line 2882
Recorder: TSSTcorp TS-L632D CD/DVGW;
Code CD - RW: 00 97 10 00; CD manufacturer unknown
ATIP data:
Special Info [hex] 1: D1 00 C6, 2: 61 a 0, 00 (LI 97:10.00), 3: 4F 3 b 4 a (LO 79:59.74)
Additional info [hex] 01:02 4A B0, 2:5 C6 26, 03:00 80 80 (invalid)02:27 A. Â? ? Â? #13 text 0 File DlgWaitCD.cpp, line 500
> Protocol of DlgWaitCD activities:
=========================================02:27 A. Â? ? Â? #14 text 0 file ThreadedTransferInterface.cpp, line 744
CIS (after recorder preparation)
0: TRM_DATA_MODE1)
2 indices, index0 (150) not provided
#0 + 2885 (2885) original disc POS = 2885 # / 0:38.35
relocatable, pos to drive for the cache-write implementation not required / required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2883 blocks [E: TSSTcorp CD/DVGW TS-L632D]
--------------------------------------------------------------02:27 A. Â? ? Â? #15 text 0 file ThreadedTransferInterface.cpp, line 946
Prepare [E: TSSTcorp CD/DVGW TS-L632D] for write in TAO
DAO infos:
==========
MCN:
TOCType: 0x00; Closed disc, session not obsessed
Titles 1 to 1: Idx 0 Idx 1 next Trk
1: TRM_DATA_MODE1, 2048/0 x 00, FilePos 0 307200 6215680, ISRC ""
Introduction DAO:
===========
___Start_ | ___Track_ | _Idx_ | _CtrlAdr_ | ___Size_ | ___NWA_ _ | _RecDep___
-150 | Lead-in | 0 | 0x41. 0 | 0 | 0x00
-150 | 1. 0 | 0x41. 0 | 0 | 0x00
0 | 1. 1. 0x41. 2885 | 0 | 0x00
2885 | Lead-out | 1. 0x41. 0 | 0 | 0x0002:27 A. Â? ? Â? #16 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:27 A. Â? ? Â? #17 text 0 file SCSIPTICommands.cpp, line 242
SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME02:27 A. Â? ? Â? #18 text 0 file Burncd.cpp, line 4320
Caching options: cache CDRom or network-Yes, small files-no)<>02:27 A. Â? ? Â? #19 phase 24 file dlgbrnst.cpp, line 1767
Caching of files started02:27 A. Â? ? Â? #20 text 0 file Burncd.cpp, line 4442
Cache writing successful.02:27 A. Â? ? Â? #21 phase 25 file dlgbrnst.cpp, line 1767
Caching of files completed02:27 A. Â? ? Â? #22 phase 28 file dlgbrnst.cpp, line 1767
Speed measurement started02:27 A. Â? ? Â? #23 text 0 file ThreadedTransferInterface.cpp, line 2676
Check position of the point disk 0 (relocatable, disc pos, no patch, orig to #0 info): write to #002:27 A. Â? ? Â? #24 text 0 File ThreadedTransfer.cpp, Line 273
Size of the memory pipe 59040002:27 A. Â? ? Â? #25 phase 29 file dlgbrnst.cpp, line 1716
Speed measurement completed: 307.7 x (46? Â? ? Â * 160 KB/s)02:27 A. Â? ? Â? #26 phase 36 file dlgbrnst.cpp, line 1767
Burn process started at 4 x (600 KB/s)02:27 A. Â? ? Â? #27 text 0 file ThreadedTransferInterface.cpp, line 2676
Check position of the point disk 0 (relocatable, disc pos, no patch, orig to #0 info): write to #002:27 A. Â? ? Â? #28 text 0 file MMC.cpp, line 21875
Set BUFE: Super link-> ON02:27 A. Â? ? Â? #29 text 0 File ThreadedTransfer.cpp, Line 273
Size of the memory pipe 8383680002:27 A. Â? ? Â? #30 text 0 file MMC.cpp, line 17311
Start narrow-gauge #2 02:28 A. Â? ? Â? #31 text 0 file DVDPlusDualLayer.cpp, line 1424
SetDriveCaps: Set LAST LBA of layer 1 to 002:28 A. Â? ? Â? #32 phase 37 file dlgbrnst.cpp, line 1767
Burn process completed successfully at 4 x (600 KB/s)02:28 A. Â? ? Â? #33 phase 78 file dlgbrnst.cpp, line 1767
Data verification started02:28 A. Â? ? Â? #34 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:28 A. Â? ? Â? #35 text 0 File ThreadedTransfer.cpp, Line 273
Size of the memory pipe 59040002:28 A. Â? ? Â? #36 SPTI-1064 file SCSIPassThrough.cpp, line 215
CdRom0: SCSIStatus (x 02) WinError (0) NeroError(-1064)
CDB data: 0 x 28 00 00 00 00 00 00 00 01 00 00 00
Key: 0x05 (KEY_ILLEGAL_REQUEST)
Printing Code: 0x21
Meaning of Qual: 0x00
Sense area: 0 x 70 00 05 00 00 00 00 0 to 00 00 00 00 21
Buffer x0a5a6500: Len x 800.................................................. .................................................. ............
.................................................. .................................................. ............02:28 A. Â? ? Â? #279 SectorVerify 20 file Cdrdrv.cpp, line 11185
Sector 0 to 1055 read errors02:28 A. Â? ? Â? #280 CDR-1222 file Writer.cpp, line 203
Checking abandoned, too many errors
E: TSSTcorp TS-L632D CD/DVGW02:28 A. Â? ? Â? #281 phase 81 file dlgbrnst.cpp, line 1767
Data verification failed02:28 A. Â? ? Â? #282 text 0 file SCSIPTICommands.cpp, line 289
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME02:28 A. Â? ? Â? #283 text 0 file Cdrdrv.cpp, line 11243
DriveLocker: UnLockVolume completed02:28 A. Â? ? Â? #284 text 0 file SCSIPTICommands.cpp, line 452
UnLockMCN - completed successfully for IOCTL_STORAGE_MCN_CONTROLExisting drivers:
Registry keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogonPost edited by: velkoto
Post edited by: velkoto
Try to remove the CD/DVD filters in the registry.
When the associated CD/DVD (such as iTunes, Nero, virtual CD software), the software is installed, they install filters in the registry, which can cause compatibility problems.(1) run Regedit (start-> Run-> Regedit)
2) navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
(3) in the right pane, delete the "UpperFilters" key and delete the key "LowerFilters".
(4) restart.If your CD/DVD programs stop working, you will need to reinstall them (preferably with an updated version).
This utility can remove the filters for you:
http://www.CSD.Toshiba.com/content/support/bulletins/su2065061/RmvFltrs.exeAlso remove the dust on the lens with a clean Microfiber cloth.
Maybe you are looking for
-
Resize Firefox 26 less than 400 PX width
Since upgrading to Firefox 26.0, it seems to be is no longer possible to resize a window to a size smaller than a width of approx. ~ 400px. I run a web application in its own instance of Firefox, which requires much less horizontal space and so I wou
-
Hello You know Flash Cards is transparent and moving flashy when pressing the FN key.After that I downloaded & installed PVAT 1.1.7.see card Flash became a dark, not transparent and does not move when you press FN plus (watch suddenly when pressing F
-
Is there any official page of HP where the latest official drivers of HP pavilion dv6-6011tx for windows 8/8.1 is listed? Page pilot multimedia HP Pavilion dv6-6011tx laptop lists the drivers for windows 7 (32 and 64 bit), but I seriously need driver
-
How to open the bcf files that come with the 2011 Highway
Recently bought Highway 2011 online and downloaded the three files given to me (via e-mail of confirmation of Microsoft), however I can not open files on my computer because they have a .bcf extension. Has anyone else had this problem, or someone ha
-
How to store and update the cache to the 2.3 OHC?
We have a few dozen workflows (CPO 2.3 process) each triggered by a single event of the tide to start. Each workflow at the outbreak extracts digital data (two or three data double-digit like for example 15, 300) from one end of point plural web serv