Drive DVD Y430 problems

Similar Questions

• DRIVER DVD or PROBLEM of DECODER MPEG 2

  Please can someone advise me?  Packard Bell iStart 1359 Office wife has just been re-set up the (a refresh/re-uninstall-back Windows so that from the first use).  Now, I find that some DVD will not play in his DVD player.  On checking, the MS tool tells me that there is no MPEG-2 decoder installed.  I think it was there originally - given that all DVD already appeared to play without any problems.  How/where this can be restored - or do we need to buy a plug-in?  Note - We are technically not too much mind so please keep any response/VERY simple instructions!  Thank you.

  Dave_At_No69.

  Not the 'mirror' would not work either one last try, if that does not work then I tried everything I could think of.  I'm sorry I couldn't help you out while.

  Real Player

  Good luck! Please rate me upward if you find my post helpful. Thank you!

• Please help - driver for the module Insp 8600 DVD + RW problem

  I hope someone can help with this... it left me speechless. Slim in my Inspiron 8600 DVD + RW drive module will no longer work. It does not appear in my computer folder. If I insert a CD or a DVD in there, it takes in and I can hear it roar, but nothing else happens. I tried the following:

  • Type d: / RUN... but it says there is no such drive
  • Exit the module and then put it back in, in case it was a problem of the seating. No change.
  • Ran scans antivirus and antispyware - nothing.
  • I checked the Device Manager and there are two drivers for the DVD drive - HL-DT-ST DVD + RW GCA-4040N is called and the other is a Generic DVD-ROM SCSI CDROM Device ( where the hell does he?). Both of them have yellow exclamation points on them. I uninstalled both, hoping that the replacement driver solve the problem after XP replaced. No luck - the 'new' drivers always have yellow exclamation points on them.
  • I also tried to uninstall these drivers and then installing a GWA-4040N driver; the message that came was something about Setup not being not not able to find anything to install or being not able to find the drive.

  As a side note, probably related, I tried to connect an external hard drive to the 8600 with a USB cord, but this player will also not appear / is not recognized.

  Can anyone offer any advice or solutions? I feel I've hit the wall. Not being not able to connect to a DVD player is a killer, because it is used for many things, including the loading of the software.

  Thank you all.

  
  

• Upgrade to el capitan and hoping to drive DVD would work properly but no, still do not play some of my DVDs. Is there an upgrade available? my library of playable DVD shrinks

  Upgrade to el capitan and hoping to drive DVD would work properly but no, still do not play some of my DVDs. Is there an upgrade available? my library of playable DVD shrinks. IMac originally purchased in 2010. DVD 5.9.5

  I'm having no problem with my DVD.

  Could you give more details about those who are out of work?

• Drive DVD - RW does not properly on the Satellite A40-702

  It's on my lap top of Toshiba Satellite SA-40-702. Five years ago.
  Hi, I have looked at the wires for this problem and have not been able to identify a similar thread yet.

  My dvd - rw play a purchased audio music cd and it will also work with disks that came with the laptop. S something works well... However, recently I tried to burn a piece of music (from i-tunes) and he showed in white, but strangeley the cd did play the piece of music OK in a machine at work. I tried now to show some other discs that I recorded on this laptop in January, and they now show that the discs and I cannot see their content (they were photos and text documents). They worked before.

  I have this weekend made many attempts of 30 photos of burn, and I tried two different brands of dvd discs blank, but even if the laptop says 'burning to disc' etc when I try to view the burned disc, there is nothing on it!

  I wonder if anyone has any suggestions please. I tried to clean the blue eye with a brush hairs inside the drawer of the dvd, that's why I expect that the next step may be just to buy a few more recent records?

  G

  Hello

  My personal opinion is; the reader cannot process the community burned due to the stressed out laser lens. It turns out that your laptop and the drive is older than 5 years.
  I put t know how the drive has been used in recent years, but due to the long period of possible use of s that the lens cannot read data from the CD/DVD now.

  This is not unusual. My brother s book can not read the CD/DVD that were burned a year ago, I presume that it of the same reason the s drive laser lens problem

  Hmm you don t have many possibilities, you can try to burn these discs with another computer/laptop and then could check if you red the data.
  The last option would replace the drive

• Satellite P300 19 p - CD/DVD burning problem

  Hi, I'm new to the forum and I hope somone will be able to help.

  I have DVD burning problems. When I use software engraving the image is usually copied ok and then the burning process starts, which usually lasts only a few moments, then the machine spits out the disc burnt and wasted.

  I usually use Corel DVD Copy 6, but have you tried TOSHIBA and other programs such as NERO. With the help of Corel VideoStudio, it burns discs with a success rate of 90%, but the problem comes when you try to copy my own created disks.

  I tried different types of discs (that is to say + R and - R), and I also tried burning speeds.

  Anbody else suffers from this problem?

  I have managed to find an error code 06077-26 - 2A 040902, made this average anyhting for anyone?

  TEMPRO alerts appear to have provided updates firmware for a number of other DVD players, but not for my machine? Maybe it's due a? All the drivers are up to date.

  Thanks for listening and the anybodies help is more than welcome.

  See you soon.

  In my opinion, you should not think about buying replacements. If you think that the drive does not properly contact service. If necessary the reader will be replaced free of charge.

• Drive DVD RW E no longer works.

  Drive DVD RW E no longer works.

  I'm running a gateway T-1412 with Windows Vista Home Premium Service Pack 2

  DVD RW drive used to work fine, but now when I put music or a DVD in drive E that nothing happens. When I click on my computer and click on the E drive, it opens and tells me to insert a disc that has already been inserted.

  I have tried everything I can think of who isn't much so help is greatly needed.

  Thanks, Dan

  Hello

  Check with Support technique Gateway, their documentation and online drivers.

  Gateway drivers and downloads
  http://support.gateway.com/support/drivers/dlcenter.asp

  Technical support Gateway
  http://support.gateway.com/support/?cmpid=topNav

  Door Documents
  http://support.gateway.com/support/SUPINFO/index.asp?cmpid=topNav

  ---------------------------------------------------------

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burn
  and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Error message: CD-ROM DRIVER has a PROBLEM when inserting disk on the new laptop.

  Original title: CD-ROM DRIVE

  tried my new laptop by inserting a disc in the CD-ROM drive and the message... CD-ROM DRIVER has a PROBLEM, I clicked on fix of the problem and still nothing.what can do to solve this problem? This is a brand new laptop

  Hi kempie2011,

  1. What is the number of brand and model of the laptop?

  2. you receive error codes?

  I suggest you try the fix it from the link given below and check if it helps.

  Your CD or DVD drive cannot read or write media

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  Also read the following article:

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista

  http://support.Microsoft.com/kb/929461

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• error message: "Please insert a disc into drive DVD D."

  I'm trying to copy files from my hard drive on a DVD. I put a blank disc and get the error message: "Please insert a disc into drive DVD D." have you tried several disks with the same result, & all are empty. The original files were on a disc & system had no problem at the opening of this disc.

  Hello

  Try this to Fix It: http://support.microsoft.com/mats/cd_dvd_drive_problems/ . Not exactly a rare problem in Windows 7.

  Let me know if this solves the problem for you.

  Kind regards

  BearPup

• [Solved] HL-DT-ST DVDRAM GT20L periph. CdRom SATA has a driver problem. The driver faces a problem of Plug-and-Play device.

  Recently, I noticed that my CD/DVD stopped working. He turns, but nothing happens; the disc is not read.
  I use Windows 7 Home Premium 64 - bit on an HP Touchsmart tx2z.

  I ran the Microsoft FixIt program through http://support.microsoft.com/kb/982116 and it has identified the following problem: 'HL-DT-ST DVDRAM GT20L periph. CdRom SATA has a driver problem. The driver faces a problem of Plug-and-Play device. »

  However, FixIt said that he was unable to solve the problem and discs are still read.

  I manually uninstalled the driver in Device Manager and then scanned for the hardware changes. The driver was reinstalled, but with the same problems as before.

  Any ideas?

  Thank you!

  Also, try following the steps for Windows Vista, which should also work in Windows 7, in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• Drive DVD DVP3950/12 does not play the converted videos

  Hello!

  My DVD DVP3950/12 player plays all videos I converted (hand brake).
  In my description are no valid information for the videocodecs that I use and it has no details for resolution. And what kind of audiocodec is able to play on my player?

  Could someone help me?

  THX!

  cluesa

  Is the drive DVD DVP3950/12 a Toshiba device?

• Help with the driver DvD Ram for satellite P10

  On my laptop (satellite p10) is Windows 2000 Professional running, but the driver DVD Ram of the Toshiba Homepage does not...
  Where can I get a driver that works on my laptop?

  Hi Val,

  The correct driver for your laptop running Wnidows 2000 should be version 3.0.8.0 and is available for download from the Web from Toshiba website.

  I presume that it is the one that you tried, so I don't know what you mean when you say that "it doesn't."

• Windows dvd maker problem: I hear but not image using windows DVD maker.

  I can hear but not image using windows DVD maker. A few obvious reasons? It's strange because it used to work and now a few months later it does not. The image is there in the start menu of the main menu, just before you press play it starts to play sound with no photos after I press play. Please help, steve gratefully.

  original title:
  Windows dvd maker problem

  Maybe the part "What to do if you have questions" of the following
  article would offer some ideas.

  How to burn DVDs with Windows DVD Maker
  http://www.7tutorials.com/how-burn-DVDs-Windows-DVD-Maker

• Drive DVD (E) does not work in a HP Windows Vista Premium system

  When I install a DVD in drive E, nothing happens.  MagicJack is installed on the computer and using the DVD player as well.

  In the device - drive DVD/CD-ROM Drives Manager - Tiger Jet CD-Rom USB Device (MagicJack) and TSSTCorp CDDVDW TS-L633M ATA devices are listed.

  Apparently the MagicJack drive does not drive the function E.

  Registry Editor fix by removing the UpperFilter and UpperFilter and reboot, lines did not work.

  Thank you

  RBB

  Try uplugging your magic Jack for a few seconds and install it back, it can set up an another hardware profile and take a next unassigned drive letter. Or change the drive letter of your DVD drive assignment:
  Click Start-> right click 'Computer'-> manage-> click on 'Continue' on the prompt UAC-> in "Computer management" slot, click on "Disk management" "Storage". On the right pane, right click on your DVD drive and click on «Change drive letter and path...» "-> click on the button 'change... '. "under-> assign a new drive letter.

• Cannot format drive DVD - Rw with Windows Vista.

  Cannot format drive DVD - Rw with Windows Vista. Download "Windows cannot format... or is unable to complete the format.  Something like that. See a solution with Windows 7, but I use Windows Vista. Help?

  Hello

  ·        What is the model number of your computer?

  ·        Who is the manufacturer of your computer?

  ·        Did you format the disc earlier?

  ·        Are you trying to format the drive using windows Explorer or through third party software?

  I suggest you read the web link, below he provided information related to the formatting of disk.

  http://support.Microsoft.com/kb/930405

  Hope the helps of information. Please post back and we do know.