Drive external DRIVE will not mount after resizing in Windows

Similar Questions

• External hard drive will not mount after the update of the Sierra

  Hi, I have an a Segate 1 TB external hard drive that I have with my MacBook Air. After upgrading to Mac OS Sierra, he refused to climb and is therefore invisible in the Finder. Disk utility detects the drive in NTFS initialized and said that all the space has been used. I tried to mount it first through disk utility, but it did nothing. Then I tried via terminal, but he returns "failed to mount. It worked fine before and also works very well on a MacBook Pro running Yosemite. It may be nothing to do with the player, as all files are intact when it is connected to the other Mac. Also, I restarted in Mac utilities and run from there disk utility, and it detected the drive, mounted and fully initialized, with the right amount of space being exhausted.

  I am looking for a solution that does not copy the files off and reformatting if possible, but I'll give it a go, if it comes to that. Thank you very much.

  Most likely your Seagate drivers are not updated.

  NTFS is most likely the culprit here.

  Go to the Seagate site and download and install the latest drivers for your drive and NTFS.

  You can start here... http://knowledge.seagate.com/articles/en_US/FAQ/007770en?language=en_US & key = ka03 A000000tzbeQAA & k = n & wwwlocale = en - us

  Hope this helps, Greg

• External CD drive will not mount on OSX

  An external CD/DVD drive will not mount on my iMac running the latest OSX update. I'm on my second CD drive (sorry Amazon). When I insert an audio CD, it is recognized. I am able to rip the CD fine, but then the Player responds neither to open unless I unplug the USB to which I am able to open it and change the CD I tried to use external power to the player. That

  s not the question. Disk Util sees only after fresh USB connection. Profile of sys can see at any time. Back to zero does not correct the problem is it better that disconnect and reconnect. All OS updates have been applied. No other devices or software problems. Y at - it a tip. This should be simple and Yes, CD player works on a Windows machine, but I have not yet tried on another machine from Apple.

  Post edited by: HOUSE is compatible OSX and the issue is not resolved.

  Is the devices designed to work with OS X?

• Apple Software Update will NOT work after upgrading to Windows 7

  Apple Software Update will NOT work after upgrading to Windows 7

  flyboy340 wrote:

  Apple Software Update will NOT work after upgrading to Windows 7

  More information is needed.

  Which machine you use, OS X are you running?

  Windows 7 running in BootCamp?

  The OS X app store is not present at all?

  AppStore is present but the update tab does not?

• WD My Passport drive external drive will not mount once my Macbook Pro is already on

  Hello

  I actually had this problem for a year or two, but I'm finally getting bugged to this topic enough to see if it can be 'fixed '.

  I have a 2 to WD My Passport portable HD connected to my macbook pro via an external (wall outlet) powered TRUST 5 x USB3 Hub.  If everything is connected, when I start the macbook pro there is no problem and the WD My Passport is mounted in the finder.  But if I remove manually the hard drive and then try to mount it again while the macbook pro is running it doesn't mount not.  It used to, but he won't now.

  In the past the WD My passport would need to unplug and perhaps the USB3 hub would need power cable disconnect from him and the USB hubs out the macbook pro.  So when I joined this new and plugged the hard drive WD in the hub, it would rise very well.  But now it's just point blank refuses to ride until I restart the macbook pro.  Once I restart it it climbs perfectly and stays up forever--until it is dismantled manually - and then I have to restart the macbook pro again so he could mount once more.

  I tried all combinations of pull cables and adapters to power but nothing has worked.  After dismantling the WD hd and plug back on the USB3 light led on the hub hub lights up and the hard drive turns manually, but, as I say, it is not mount and it is not visible in disk utility.

  Any ideas please?  It's a bit annoying to have to keep restarting the mac whenever I had to unplug the hard drive WD.

  "As issued" WD Passport appear to cause a number of reports of trouble around here. You have already taken the first "not best" - using a powered hub. Just make sure that the hub is really power (lights on, for example). It could be that the external drive is in its death throws.

  This happen if the WD is the only thing on the powered hub?

  The Mac USB ports work with other devices?

  Here's what my experience with these things has believing me. WD made great bare discs, but I can't be so kind to their pens. Three questions:

  (1) I think that they should use chipsets which are not very easy to Mac.

  (2) most driving the ship formatted for Windows

  (3) even those shipped as "Mac editions have some odd which makes it difficult to access file formatting.

  If you do not have to share the drive with a Windows computer, you can reformat the drive and that often fixes "fail to mount/recognize" question. Disk utility is your tool of choice here because it is already installed on your Mac. Completely erase the WD drive by selecting the tab 'Clear' in the bar tabs to disk utility. Define the plan of Partition to GUID Partition map and journaled for Mac extended format. Press the button 'clear '. The reader will now will be rid of eccentric WD partitioning and formatting schemes and be a good Mac hard drive.

  If you share the road with a Windows computer, consider getting a better workout. After having fought external drives 'brand' on my computers and others that I maintain, I now use only boxes of other computer world with naked WD drives inside. Since this change, I have zero problems. For my MacBook Pro, I use this forum:

  https://eShop.MacSales.com/item/OWC/MEPMU3ES/

  I ordered the external power optionally for use at home and go on the road bus-powered. It's an empty envelope - just a hard drive of nu. They are more expensive than the stuff that Staples puts on sale every weekend, but are much more reliable. I ask the question. "What is my value data?"

• P6-2371: my HP laserjet mfp 1212 will not scan after moving to windows 8 10

  I have a windows HP laserjet mfp 1212 electrician network connected to my desktop HP i5 (p6-2371).  Since the upgrade to windows 10 8, although I can print and photocopy I can no longer scan.   I reinstalled the drivers from HP, the pint of HP and a Scan doctor, nothing helps.   The doctor Print & Scan detects the device but says it can not communicate with him.  I also have a Kodak AiO installed as a USB device that scans is more well that it prints.

  Your help please

  Hi @ptpk,

  Thanks for getting back to me.

  The firmware is very important to update.

  You can try to update the firmware from another computer?

  • Try using a USB connection.

  It is possible that the driver was corrupt, so we will need to remove it and reinstall.

  Please follow the steps described in this guide, HP printers - printer problems after upgrade to Windows 10.

  If the problem persists, follow these steps to see if you can solve the problem.

  Let's start by cleaning up your computer.

  • Cleaning disc in Windows 10
  • Perform the clean boot in Windows 10 / 8 / 7
  • Use the File Checker system to repair missing or corrupted system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  Uninstall and reinstall the HP software.

  If you use a USB connection between your computer and the printer please unplug this cable now.

  Step 1: Remove the printer:

  We want a clean slate to install your printer on the computer Windows 10. So, I'll have you ensure no trace of your HP LaserJet. displays currently installed on your computer.

   

  1. click on the Start button

   

  

   

  2. type programs and features. If a search does not start automatically, you will need to type programs and features in the area of "Ask Me anything".

  3. click on programs and features to launch the window.

  4. in programs and features, will populate a list of the programs installed on your computer. Please scroll down and look for your HP LaserJet. If you see your HP LaserJet listed, click on it and choose Uninstall.

  5 follow the prompts on the screen to complete the uninstallation. Once the uninstall is complete successfully please close programs and features.

  6. then, click on the menu start of new

  7. this time type devices

   

  8 click on devices and printers to launch the window.

   

  

   

  9. in devices and printers are looking for your HP Deskjet. If you see if if please right click above and choose 'Remove' or 'Remove'.

  10. Once your HP LaserJet exceeds showing in devices and printers please click on any device in the list of Printers once just to highlight. Click the print server properties on top

   

  

   

  11. click on the drivers tab

  12. look for your HP Deskjet printer driver. If the list, please click it and choose delete

  13. Select delete the driver only

  14. Select OK

  15 click apply and OK in the print server properties window.

  16. close devices and printers. Please proceed to the next step.

   

  Step 2: Install the device:

  1. Please click here to download the full functionality of the software and the driver for your printer
  2. Once the download is complete, follow the prompts on the screen to install your printer
  3. If you use a USB cable connection, leave the disconnected cable until the installation program prompts you to connect

  Once installation is complete, please try printing and scanning.

  Source published by my colleague X-23.

  If the problem persists, you can try the solution proposed in the thread below.

  (1) open the command prompt window by clicking on the Start > applications > Windows system > guest.

  Type: net stop spooler

  Enter: net start spooler
  Type: exit

   

  2) open Windows Explorer and navigate to:
  %SystemRoot%\System32\Spool\Drivers\W32x86

  NOTE: any % is usually C:\Windows, but it might be "winnt" or something else; It is set when the OS is installed.  Most systems are like this C:\Windows\system32\spool\drivers\w32x86

  (3) in the w32x86 folder, there will be other folders and files.  Delete everything inside, but DO NOT remove the w32x86 folder.

   

  4) restart the computer - perform clean boot in Windows 10 / 8 / 7

  Source Posted by a member of community jaredjb

  Please reply to this message with the results. I can't wait to hear strings attached good luck!

• HP Pavilion p6780uk: my hp Photosmart C4180 all-in-one will not scan after update to Windows 10

  Not sure if Windows (32-bit or 64-bit) 10

  Welcome to the community of HP, @DavidJ70

  I came across your post about how you are unable to analyze after upgrade to Windows 10 and wanted to answer with my suggestions.

  First run Installation Wizard printer here: use of diagnosis HP for printers HP Windows tools

  After that, the feature complete driver and software must be installed for your printer on your computer. Try to scan the image. If there are problems, let me know all the details, errors, etc., and I'll do my best to help!

  Click on the thumb to below testify my help!
  Click on the "accept as Solution" if I'm you guide to a solution!

  Best wishes

• Lightroom 6.5 will not work after restoring the windows 10

  First of all, let me say that Adobe support for a pro user product sucks. Really? no other than this support?

  My windows 10 workstation crashed and did a restore. I understand that it is early and I had to reinstall the update 6.5.

  Problem is that Lightroom does not open because he repeats to me there is problem of catalog and will not allow last backup is only a few days to work.

  Then. How to solve this problem?

  The only thing that worked was completely reinstall Lightroom 6, and then apply the latest update.

  After that, I was able to use the last catalog had been saved.

  You guys seriously need better than this forum support if you want to think of yourself as a product for professional use.

  When all else fails reinstall, but this kind of support, it's not what you need.

  Capture One to become a better alternative if you have a serious problem.

• Seagate external hard drive will not mount

  I can't get a TB Seagate Backup Plus 2 player to mount on my Macbook Pro 2011. When I plug it into the USB port, disk utility detects it. I ran check disk and it said the necessary repair disk. Then I ran the repair disk and it said it was successful. However, the player still don't let it go. The disc appears on the other Mac, but not my Macbook Pro. It is not the problem of the USB port either because I was able to mount other external hard drives in order to use it. The reader has already worked on my Mac until I updated my OS from Snow Leopard in Yosemite.

  Something could be wrong with my Mac that prevents the installation disc, or is it more likely to be a problem with the drive?

  I guess it is related to software driver for Seagate to support the NTFS on mac.

  OS X support NTFS natively, but read-only.

  The installation of the supplied driver allows read-write access, but it is obsolete seamingly.

  I just got the last of Seagate site, but it is still pretty new. The Info said taking in charge until Mavericks only.

  If this is the case, you can take a from below.

  1. Uninstall the current driver and expect to release a new Seagate. In the meantime, you can have read access to the disk.
  2. Uninstall the current driver and get the latest version of the driver by the developer instead of Seagate. The last time the developer (Paragon) even on El Capitan and without limitation to Seagate drive. (Paragon is not free but has the trial period - http://www.paragon-software.com/home/ntfs-mac/ )
  3. Uninstall the current driver, then take the alternative. The son will be your help for this. - Need to write to the drive (ntfs) outside Yosemite

• External hard drives do not mount after macOS Sierra Upgrade I just upgraded to macos sierra, and my hard drive (USB) is not editing (which still appear in disk utility).   Any ideas?

  

  It is an NTFS drive and needs a driver from Seagate.

  See: http://www.seagate.com/gb/en/support/downloads/item/ntfs-driver-for-mac-os-maste r - dl /

• c drive is not available after refresh of windows 8

  My computer won't start so I decided to update it.

  Hi Renon,

  I suggest you perform a complete system recovery to solve the problem. Follow the steps here: http://www.kb.sony.com/selfservice/documentLink.do?externalId=C1031321

  Note: If my post answered your question, please mark it as an "accepted Solution".

• All-in-one HP OfficeJet J4680: Solution HP will not launch after recent updates Windows 10

  HP Solution would not launch before 10 Windows updates have been downloaded. After the updates have been downloaded on 03/01/16, HP Solution launched and worked. 05/01/16, ddoes HP Solution, not throw again. I've read of other recent and clear solutions on what must be applied to resolve this problem.

  @MsAymz

  Try to uninstall this update until Microsoft comes up with a fix.

  Security Update for Internet Explorer in the drive for the Windows Version 10 1511 (KB3132372)

  How hide/block updates to Windows in Windows

  December 28, 2015, Adobe released a security update for Adobe Flash Player fix that they call "critical vulnerabilities" that allow an attacker to take control of the system concerned.  Microsoft has published notice 2755801 of security and updating of security KB3132372 to make the Adobe Flash Player update available to all users.

  Adobe and Microsoft are aware of the reports of some application crashes after you install this update, conducting research on this problem.  We will post more information in this thread in KB3132372 under the more information section.

  indows_10-update/some-applications-may-crash-afte http://answers.Microsoft.com/en-us/Windows/Forum/w...

  REO

• Runes of Magic will not play after upgrade to Windows 7 64-bit

  Have upgraded to window7 64 bit that I use now the 8 GB of ram

  Runes of Magic was playing on my old windows version but usually install a new

  Get message that windows could not find a version of the game, so I downloaded the patches for the game manually

  Game Launcher now returns but crashes after I selected the game

  Any help would be greatly appreciated

  Thank you

  Hello

  1. have you made changes on the computer before this problem?
  2. What is the full error message or error code?

  I suggest to perform a clean boot, and then try to download and install the game and check if it helps.

  Clean boot will check if any third-party application is causing the problem, as the clean boot helps eliminate software conflicts.

  How to solve the problem by running the clean boot in Windows 7: http://support.microsoft.com/kb/929135

  Note: once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual.

  Note: Runes of Magic is compatible with Windows 7 64 bit

  Reference:
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?l=en-us&type=software&s=runes%20Of%20Magic%20&OS=64-bit

  Note: If you still have the problem then I suggest you to contact the game manufacturer.

• CD/DVD drive does not work after 8 Win instalation

  Since a month since I've updated my windows in windows 8, everything works fine but the DVD - RW.

  When I put the blank cd and try to open it, it gives me error when opening by saying:
  "windows could not complete the format".

  Who's a software or a hardware problem?

  waiting for help!

  This means that your CD/DVD drive no longer works and is not recognized by the system?

  If Yes, then I would recommend checking this Toshiba document that I found on the portal of the knowledge base site:

  + Why my CD/DVD drive does not work after upgrade to Windows 8? +
  http://APS2.toshiba-tro.de/KB0/FAQ2B03F10002R01.htm

  You must uninstall the programs from Toshiba:
  TOSHIBA Recovery Media Creator
  TOSHIBA Disc Creator

• DC Adobe will not open after new installation

  I just did a clean install of Adobe Acrobat Standard DC and it will not open after installation on Windows 7 Enterprise. It's also does not give me that whole EULA prompt.

  Right-click on the exe > click 'run as administrator '.