Driver Ethernet and network controller missing after the Installation of 7 costs Windown

Hello

I have Sony Vaio VPCEG25EN E series laptop with Win 7 64 bit pre installed.

I had installed Win 8 intended to test and when it is again installed win 7, I'm missing my network and Ethernet controller drivers. I don't see any network except for Bluetooth network card adapters.

Tried to install the drivers from the SONY site but in error.

Apart from these 2 drivers

PCI device
Simple PCI controller communications

SM Bus controller

are also missing.

Please let me know the solution how to install the drivers and where to look for it.

IMP Note: if I install the trial win 8 again, I'll have all my drivers after installation, but during the installation of Win 7, they disappear.

Advertisement

What error do you get when you try to install the drivers of sony?  Windows generic drivers should work...  In Device Manager, do you have a selected and right click 'check for changes on the hardware?

Tags: Sony Computers

Similar Questions

  • NB510-109 - driver missing for Ethernet and network controller

    Hi again

    I replaced the HARD drive on my NB510-109 and installed W7 32-bit teacher. Windows unfortunately has no Driver for my network controller and Ethernet. The seller of Ethernet is 1969 (Atheros), but the driver I found does not work.

    The seller of network controller is 10EC (Realtek or Acer) but I can't find a driver.

    Is there a link where I can load the original driver CD/DVD?

    PS: I could not save the original data of my old HDD for HARD drive has not finished.

    Are you looking for driver LAN or WLan driver?
    I m asking because the network controller could mean the WLan or LAn card.

    However, the laptop supports the Atheros LAN card and you must install the Atheros LAN driver.
    The WLan card is made but Realtek. Its 802.11bgn RTL8188CE card Wlan.

    On the page of the Toshiba UE driver you can find two drivers Atheros LAN to Win 7 32 bit:
    v 2.0.9.9
    v 2.0.11.12

    I recommend you to check them both.

    Realtek WLan driver can be downloaded from Toshiba WLan Portal:
    http://APS.toshiba-tro.de/WLAN/?page=downloads

  • driver Ethernet and network for «Windows lenovo xp 7 style 2010»

    Hello

    I have a lenovo 3000 N200 & recently upgraded to Windows lenovo xp 7 style 2010

    but now his LAN does not work; Device Manager indicates that it can not install the driver ethernet & network

    how it can be fixed?

    concerning

    Finally, it has been resolved after several uninstallation / installation of device drivers and restart windows!

  • We get an error "the driver of the scanner supported by this software is not installed." Install it and then try again"after the installation of MP Navigator

    * Original title: drivers Canon MP160 printer (scanner-MP navigator) on issues of Win8

    Hello

    I bought a win8 system. I tried to install the Canon MP160 driver on the system.

    Had trouble at the start, but was able to install in compatibility mode for win 7, which solved the problem of the printer.

    Now I have problems with the installation of MP Navigator to scan.

    I am able to install MP Navigator but receive error message "scanner driver supported by this software is not installed.» Install it and then try again."

    Help, please.

    Pavan Sandur

    Hi Pavan,

    Thank you for the information.

    You can uninstall the drivers from Device Manager and try to install the latest versions to check the issue.

    If the problem persists, try to install the software of the browser in compatibility mode and see if that fixes the problem.

    http://Windows.Microsoft.com/en-in/Windows-8/older-programs-compatible-version-Windows

    You can also get in touch with the Canon Support for assistance on their products and compatibility.

    http://www.Canon.ca/inetCA/contactus?m=loadcontactus&lang=en&commId=3&typeid=1&msegid=2

    It will be useful.

  • Joined to a domain and an administrator remote after the installation of SP1, updated to 10 settings (clean install) then

    Wipe the hard disk, reformatted and did a clean install of OS7 home (fossoyées pro hoping group domain policies and etc. would not be a problem).  But they are still there. Reinstalled again.  I can't remove the files manually, give me permission. Loading guard who looks like a fake update file, but I can't delete that either.  I'm at my wits end.  I also have a problem with one of my Outlook email accounts, displaying a string of what looks like a key under my user name.  I have dealt with this for 2 months.  had my machine to two different local mechanics and nothing.  Even exchanged the motherboard and the drive.  How's it relate?  I do not even use the same key.  The only way he could do it is through my network connection. (Disabled Wifi too).

    I read something on the Panther Trojan and I do not have a file of Panther on my machine (which again, I can't delete).  I didn't even think that HOME version had this kind of remote administration and yet it moves it. Its load of 32-bit strange file and run it on a 64 bit system.  I don't know what to do from here.  I can't get a version of Windows installed which does not suck up all my processing power and crazy amounts of data transfer.  I pulled out an old HP Pav and am now loading XP on it.  At least I will be able to view and edit files it contains.  I don't think safe, even check my email on this machine. (I use my ipad for that).

    Here are the results of the queries from the command line, screenshots and event log shears.   Since I was the last reinstall at about 21:00 there are 294 Logon and created special logons.  Not to mention that I had an another windows machine and one android corrupt their hooking up to my Dungeon phone.  The worst is a 10 years ' worth of my design files holding external drive.  Sighhhhhhh...

    IM so sick of looking at this.  Im going to bed and hopefully not dreaming about it.  If someone can tell me how to stop this happening, I would SO appreciate it.  Support for Windows is a joke.

    I have run 3 different programs of Virus Scan on it, reformat the drive twice (wiped to zero once), and used three different install media (three different versions of Windows. 0 s 7 home, pro and pro OS7 OS10 (7 pro is what I was running when this began).)  Again, it is after that I paid two services of different repair to diagnose, pull the wireless network card, replace the motherboard and replace the disk.  After that I freaked out on them they began to throw the installation discs and Home keys. lol seriously, I might as well throw my money down a hole. (the key I've finally pulled the machine isn't that I've never owned?) I guess that's why I'm trying so hard to get pure installed, I already so much money in it.  I should probably just give up and load Linux.

    If I ever get my hands on this bloody trusted installer it is a dead man. Thanks in advance!

    Microsoft (R) Windows (R) operating system group policy result tool v2.0
    Copyright (C) Microsoft Corp., 1981-2001

    Created on 20/07/2016 at 23:03:12

    The RSOP data for OWNER-PC\Administrator on your PC-OWNER: Logging Mode
    ----------------------------------------------------------------

    OS configuration: Standalone Workstation
    OS version: 6.1.7601
    Site name: n/a
    Roaming profile: n/a
    Local profile: C:\Users\Administrator
    Connected over a slow link? : no

    COMPUTER SETTINGS
    ------------------

    The last time group policy was applied: 20/07/2016 to 22:31:33
    Group Policy was applied from: N/A
    Group Policy slow link threshold: 500 Kbps
    Domain name: 37L4247E29-32
    Domain type: Windows NT 4

    Applied Group Policy objects
    -----------------------------
    N/A

    The following Group Policy objects were not applied because they were filtered
    -------------------------------------------------------------------
    Local group policy
    Filtering: Not applied (empty)

    The computer belongs to the following security groups
    -------------------------------------------------------
    Required at the system level
    Everyone
    Builtin\Users
    NT AUTHORITY\SERVICE
    LOGIN CONSOLE
    NT AUTHORITY\Authenticated users
    This organization
    BDESVC
    BITS
    CertPropSvc
    EapHost
    hkmsvc
    IKEEXT
    iphlpsvc
    LanmanServer
    MMCSS
    MSiSCSI
    RasAuto
    RasMan
    RemoteAccess
    Annex
    SCPolicySvc
    SENSE
    SessionEnv
    SharedAccess
    ShellHWDetection
    wercplsupport
    Winmgmt
    wuauserv
    LOCAL
    BUILTIN\Administrators

    USER SETTINGS
    --------------

    The last time group policy was applied: 20/07/2016 to 22:36:33
    Group Policy was applied from: N/A
    Group Policy slow link threshold: 500 Kbps
    Domain name: OWNER-PC
    Domain type:

    Applied Group Policy objects
    -----------------------------
    N/A

    The following Group Policy objects were not applied because they were filtered
    -------------------------------------------------------------------
    Local group policy
    Filtering: Not applied (empty)

    The user is part of the following security groups
    ---------------------------------------------------
    None
    Everyone
    BUILTIN\Administrators
    Builtin\Users
    NT NT\INTERACTIF
    LOGIN CONSOLE
    NT AUTHORITY\Authenticated users
    This organization
    LOCAL
    NTLM authentication
    High mandatory level

    After you activate the hidden administrator account (which already had a defined password btw)

    C:\users\administrator>set
    ALLUSERSPROFILE = C:\programdata
    APPDATA = C:\Users\Administrator\AppData\Roaming
    CommonProgramFiles = c: files
    CommonProgramFiles (x 86) = c: Program Files (x 86) \Common Files
    CommonProgramW6432 = c: files
    COMPUTERNAME = OWNER-PC
    ComSpec=C:\Windows\system32\cmd.exe
    FP_NO_HOST_CHECK = NO
    HOMEDRIVE = C:
    HOMEPATH = \Users\Administrator
    LOCALAPPDATA = C:\Users\Administrator\AppData\Local
    LOGONSERVER = \\WIN-01J5F1J7NAH
    NUMBER_OF_PROCESSORS = 4
    OS = Windows_NT
    Path = c: Windows system32; C:\Windows; C:\Windows\System32\Wbem; C:\Windows\System32
    \WindowsPowerShell\v1.0\
    PATHEXT = .COM; EXE;. BEATS;. CMD;. VBS;. VBE;. JS;. JSE;. WSF;. WSH;. MSC
    PROCESSOR_ARCHITECTURE = AMD64
    PROCESSOR_IDENTIFIER = Intel64 family 6 model 23 Stepping 10, GenuineIntel
    PROCESSOR_LEVEL = 6
    PROCESSOR_REVISION = 170 a
    ProgramData = ProgramData
    ProgramFiles = c: Program Files
    ProgramFiles (x 86) = c: Program Files (x 86)
    ProgramW6432 = C:\Program Files
    PROMPT = $P$ G
    PSModulePath=C:\Windows\system32\WindowsPowerShell\v1.0\Modules\
    PUBLIC = C:\Users\Public
    SESSION = Console
    SystemDrive = C:
    SystemRoot = C:\Windows
    TEMP = C:\Users\ADMINI~1\AppData\Local\Temp
    TMP = C:\Users\ADMINI~1\AppData\Local\Temp
    USERDOMAIN = OWNER-PC
    USERNAME = administrator
    USERPROFILE = C:\Users\Administrator
    windir = C:\Windows
    windows_tracing_flags = 3
    windows_tracing_logfile=C:\BVTBin\Tests\installpackage\csilogfile.log

    This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)

    If you give us a link to the new thread we can point to some resources it
  • Error - system32/hal.dll is missing after the installation of updates.

    Original title: updates destroy xp installation.

    Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    Ideas: i'm trying to reinstall xp sp1 on an old toshiba laptop (m35-s456).  After installation and the installation of sp2 and a bunch of KB, reboot xp will not charge and comes up with an error saying the system32/hal.dll file is missing.  no idea why an update would impact on this file?

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem

    Hi derek45,

    The updates you have installed Service pack 1 and 2?

    This problem may occur if the Boot.ini file is missing, damaged, or contains incorrect entries.

    You can follow this link and check if the problem persists.

    "Invalid Boot.ini" or "Windows did not start" error messages when you start your computer

    Hope the helps of information. Please post back and we do know.

    Concerning
    Joel S

  • Networking broke up after the installation of the 3.14

    Hello

    I just recevived a command prompt to install v3.14 on osx Lion. After installation that the netwrok in the virtual machine does not at all - it makes appear a dialogue stating:

    Ethernet1 cannot connect to network virtual/dev/vmnet8.

    More information can be found in the vmware.log file

    Unable to connect the virtual device Ethernet1.

    I tried fiddling with the settings of the network without success and I can't find the log file

    Any help appreciated gratefully.

    Neil

    You've restarted the Mac since the upgrade?  If not, then restart the Mac and see if you still have a network problem.

  • Network stops working after the installation of the VMware Tools on linux comments

    Hello

    I m facing problem after that, sometimes, sometimes not after a comment tools and vmware linux installation.

    If the installation of vmware Linux tools everything seems to work perfectly. No errors, nothing.

    The last thing to do after that tools installed will run successfully is to run the following commands (produced by the message from the installation program tools)

    /etc/init.d/network stop

    rmmod pcnet32

    rmmod vmxnet

    modprobe vmxnet

    /etc/init.d/network start

    This works fine as well, but after the next reboot the network stops working sometimes.

    The linux guest runs under VMware Server 2 using tools VMwareTools - 2.0.0 - 122956.i386

    The strange thing is that this happens all the time when install linux clients and tools.

    Guest operating system is RHEL40U5

    Any help how to avoid this is much appreciate.

    Better with respect to Agent.

    Why not add the commands above to the file etc/rc.d/rc.local. It will take a cae of the rest every time that you restart your virtual machine. I hope this helps...

    Concerning

    Anil

    Save the planet, go for green

    If you have found my reply to be useful, feel free to mark it as useful or Correct.

  • Problem: My computer hangs and does not restart after the installation of MS Update KB2479628.

    Tuesday February 11 I turned my hp Compaq nx7300 off I saw that she was installing updates I thought that nothing of what I had set to automatic updates. On Wedndesday that I have tried to re - turn on my laptop it installed updates. I got a black screen with white writing. The laptop then ran restoration of boot, but he was not able to repair itself and turns off. I tried to turn it back on a few times that I was in total disbelief that a MS Update would do this to my computer, it still does not.

    I tried to start the computer in safe mode, but it does not work.

    I tried to do a system restore but evertime I tried it there was an error, I tried all eight restore points but all back "an unspecified error occurred during system 0x800700b7 restore.

    "In restoration of start I clicked on ' view diagnostic and repair details" it said all tests have been performed with success, but at the bottom it says ' root cause found - boot critical file D:\Windows\system32\ntkrnlpa.exe is corrupt.

    I had to reinstall windows 7 pro three times so far and have now developed to the point that it is KB2479628 update of MS that is causing the problem. I the have not installed this time and have had updates to the manual

    What can I do about this problem, I spent at least 20 hours on this problem now, and looking for the many other forum of people seem to have similar problems. I'm worried that KB2479628 will settle by accident when I want to install some other updates?

    My computer laptop originally had Vista Business top but has been upgraded to Windows 7 32 bit, clean install, I use Microsoft Security Essentials, I've never had installed norton or macafee.

    Thank you very much for all your time and your help is greatly appreciated, I'm sure I'll be at the time when SP1 is available.

    Until then your your :-)

  • HP Pavilion g6 - 2264ca: HP Pavilion g6 - 2264ca Notebook PC Ethernet and USB controller missing

    NEED HELP!

    Recently, I went down my HP Pavilion HP Pavilion g6 - 2264ca Notebook PC of Windows 8 for Windows 7. Only Windows 8 drivers are listed on the support page, but they seemed all to install and works very well except for my CONTROLLER USB and ETHERNET. It is not that all drivers in the title of the support page and update of Windows cannot find them, neither can update of pilot programs. Here's what it looks like in Device Manager.

    Any suggestions where I might be able to get these drivers? Thank you!

    (1) USB Controller - PCI\VEN_1022 & DEV_7812 & SUBSYS_1849103C & REV_03

    While the first pilot, that I sent you must have worked, you can try one

    http://support.AMD.com/en-us/download/chipset?OS=Windows+8.1+-+64

    (2) Ethernet Controller - PCI\VEN_10EC & DEV_8136 & SUBSYS_1849103C & REV_05

    Download and install the 5th on the list. (Win7 and WinServer 2008 R2 Auto Installation Program (SID: 1497589))

    http://www.Realtek.com.tw/downloads/downloadsView. aspx? LangId = 1 & PNid = 13 & PFid = 5 & Level = 5 & Conn = 4 & DownTy...

    If you have any other questions, feel free to ask.

    Please click the 'Thumbs Up' white LAURELS to show your appreciation

  • The menu icons and desktop start missing after the start of the desktop computer

    Original title: I do not see my bar of tasks or deskop

    When I start windows xp, I don't see the start menu or the desktop icons, only the desktop wallpaper. I was able to access the internet Explorer via windows Task Manager...

    Help me please! :))

    Hi Daannii,

    1. don't you make changes before the show?

    Try the following steps to start a process of the Windows Explorer and check the result.
    a. start your computer and boot to the desktop.
    b. press CTRL + ALT + DELETE, and then click Manager tasks.
    c. click on the file menu, click New task (run...).
    d. type % windir%\explorer.exe, and then click ok.
    e. restart the computer and check if the problem persists.

    For additional troubleshooting steps, see the following article: http://support.microsoft.com/kb/318027

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • CC of Lightroom missing after the installation of the CC

    I have a new camera to buid and must do an update on the Lightroom (Version 5.7.1) that I can read the new photos. Also I build the new CC package. If I can update the PS and the bridge, but not the Lightroom. Is still the old version in the CC. I miss the new App Lightroom CC, its not visible in the list of the App.

    your computer/operating system probably does not care cc lr.  for example, it is not 64-bit.

  • find the port and URL for EM after the installation of the database

    Hello

    I use the database oracle 10g on windows platform.actually I forgot to notedown URL for the Enterprise Manager after installation of my oracle database.

    now I want to access my business manager, but do not know the RL.

    can someone tell me please how to find URL for Enterprise Manager 10g database after installation? where he is saved?

    Thanks and greetings
    VD

    Hello..

    Yes, it should work... That's what I was going to write in my reply - to check the readme file. Well, I'm just having a database on my pc and the emca_date_time file contains the following lines at the end.

    CONFIG: No value has been set for the ORACLE_HOSTNAME parameter.
    November 26, 2008 18:32:47 oracle.sysman.emcp.util.ClusterUtil getLocalNode
    CONFIG: isLocalNodeDone: true localNode: null
    November 26, 2008 18:32:47 oracle.sysman.emcp.EMDBPostConfig performConfiguration
    INFO: > database control URL is http://Anand:1158 / em

    Anand

  • partition of bootcamp missing after the installation of El Capitan

    I disabled the integrity of the system by typing 'csrutil turn off' in the terminal, however I have not yet downloaded or rebuilt GPT Fdisk.      I can install GPT Fdisk now or do I have to re - turn on the integrity of the system?

    Thank you

    You can install the GPT Fdisk. Never 'building you' because it is an executable file. SIP can be reactivated later. Is there a specific problem you're trying to solve using Gdisk?

  • Set up the controller ethernet and network drivers Windows XP 32-bit & missing and impossible to get online

    HP Pavilion dv6205us had a blue error screen and only solution was to reinstall Windows. Have a Windows XP Pro disc, someone gave me and reinstall and repair.  Tried to reboot the computer, it would not start.  After several methods & attempts, I can restart now).

    Windows XP is old version 2002 Service Pack 2.  Need several updates and drivers who have not installed, the ethernet & network controllers are not available to log on the internet.

    I have tried several sites but need to download a program. I download the program from another PC flash drive and install on HP;  the program needs internet connection - is not available.

    Went to Device Manager / found following: (yellow mark and code-28 points)

    VINZ & DEV provided:

    1180-0592 base system device

    1180-0843 base system device

    1180-0852 base system device

    8086-1092 Ethernet controller

    Network controller 14E4 - 4311

    Device PCI 8086-27 d 8

    8086 SM Bus controller - 27DA

    Video controller 8086 - 27A 6

    Video controller (VGA compatible) 8086 - 27A 2

    Hello:

    Here are links to the drivers you need:

    First install the chipset driver and restart.

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-39732-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

    Then, install the Intel graphics driver and restart.

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-44164-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

    Audio:

    All first install this driver... and restart

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-45958-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

    Then, install this driver and restart.

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-45941-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

    Ethernet controller:

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-43103-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

    Network controller: it's the latest XP driver for the card to your laptop wireless.

    http://h20566.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=3688870 & spf_p.tpst = swdMain & spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_101092_1%257CswEnvOID%253D1093%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument & javax.portlet.begCacheTok = com.vignette.cachetoken & javax.portlet.endCacheTok = com.vignette.cachetoken

    Base system device

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-42847-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

    Quick Launch buttons:

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-57820-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

    Modem:

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-44166-1 & CC = US & DLC = in & lang = to & LC = on & os = 228 & Product = 3224055

Maybe you are looking for

  • Satellite L350-171 dead after 2 weeks

    Hi all I bought a Satellite L350-171 2 weeks of Tesco Direct. Went to the Toshiba brand because of rumors of reliability. A few days before, the computer could not turn on. Tried unplugging the charger/etc, but no joy. Called Support technique of Tos

  • Search for files which file name contains a specific string

    Hello I'm lookng for a way to find all the files in a directory, what part of the file name contains a specific string. for example: String = Hello files; -1hello2.txt -22he45.txt -gehello42353.txt... The result should be an index or the full file na

  • Microsoft server 2008 r2 standard

    error ox80070005 I replaced the hard drive and had to re activate microsoft Server Above the error message pops up Here is the result diagnosis MGA Help, please Diagnostic report (1.9.0027.0):-----------------------------------------Validation of Win

  • I and the error code: 80169D 94

    Trying to redeem my Xbox live 3-month gold subscription card prepaid on my Xbox and Xbox.com. It won't pay back, what can I do

  • Window Vista Home Premium now, I download again at this same computer and does not activate

    [removed personal details] I HAVE THE ORIGINAL OF THE INVOICE WITH ME.IF YOU WANT, I WILL SEND YOU.Thank youKAMAL ARIJA Original title: I bought this computer 3 years from DELL with window vista home premium now, I download in my computer even and wh