Driver problem: Windows Server 2008 R2 on server T110 II with PERC S300 (RAID10)

I have the Dell PowerEdge T110 II server with PERC S300 RAID card.  I installed 4 hard drives & them set on RAID10 in initial configuration.  The card mother recognizes the PCI-E card, which in turn recognizes readers.

I pop in the Windows Server 2008 R2 DVD and I start from DVD, but when I get to the part where I have to choose a file location, it appears that he is not a player available.  There is another option to add a driver.  Then I went on the site ( http://tinyurl.com/PercS300driver) downloaded appropriate driver, added to USB & when I get to this screen, I'm trying to add the driver.  However, he said "there is no signed in this folder drivers."

Does anyone know what I might be missing?

You are using the wrong driver.  The one you linked to says it's for Server 2008 x 86.  As 2008 R2 64-bit only, there is no way it will work.  Use this driver for 2008 R2 (you must change the drop down menu on site driver downloads / to the correct operating system):

www.dell.com/.../DriverDetails

Be sure to run first to extract it, and then put the contents extracted on your CD/DVD/USB for use with the link to load a driver.

Tags: Dell Servers

Similar Questions

  • How do I dual boot windows 7 a physical drive and windows server 2008 R2 to a second drive

    I bought a new 'high-end' and want to leave the current WIndows 7 Home Premium (64 bit), as is.  I want to install a second drive hard and on this new drive, install WIndows Server 2008 R2 so that I can run hyper-v.  I know I have to edit the BCDEDIT, but EVERYWHERE I look for help on this subject, he refers to a virtual hard disk... I don't want to run Server 2008 from a virtual hard disk... but rather a native installation.  Is this possible... If yes HOW?  I know he's probably changed since the days of WIndows 2000 and WIndows 2003.

    Hello
     
    Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the following link for assistance:
    http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

     
    I hope this helps.
  • HP pavilion g7: no good LAN driver for Windows Server

    Hello

    I'm trying to implement Windows Web Server 2008 as a second operating system.

    System is installed, but I got the error with the network card Realtek RTL8101 Family PCI - E Fast Ethernet NIC (NDIS 6.0), Manager material poster 10 for this driver error code.

    Could you help me with the right driver for Windows Server 2008 or how to solve this problem?

    On Windows 7, everything is ok with LAN. Laptop is HP Pavilion g7-1253er

    Thank you and best regards,

    Sergey

    Hi, Sergei:

    You can try the driver for the CARD directly on the Realtek site.

    Try the automatic installation, which is the 4th down on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

    Best regards

    Paul

  • All-in-one OfficeJet 5610: HP OfficeJet 5610 all-in-one driver for Windows Server 2003 standard edition

    Named for the installation of the driver for Windows Server 2003 standard edition for the printer model HP OfficeJet 5610 all-in-one.

    Hello

    The HP Officejet 5610 compatible only with client operating systems, it is incompatible with any OS Server 2003 or 2008.

    You can find the printer specs below:

    http://support.HP.com/us-en/document/c00420495

    Shlomi

  • HP Envy (700-420nx): HP Envy 700-420nx Ethernet (network driver) for Windows Server 2012

    I recently converted my desktop (HP Envy 700-420nx) in a server machine PC, running Windows Server 2012. But unfortunately the network stopped working. Then I installed the network (Realtalk) for windows 8.1 driver. But the problems still exist as it is. Says "No correct IP configuration" after an auto repair, "United Nations identified network" on the list of the networks.

    This is why I would like to download the specific driver for Windows server 2012 or any other possible solution to this matter is appreciated.

    Thank you

    Hello:

    See if the driver directly from Realtek works... DL and install the 3rd pilot (4th point) on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  • Can upgrade you Windows Server 2008 RC with SP2 to Windows Server R2 2012 with the option to upgrade?

    We currently have the server running Windows Server 2008 RC with Service Pack 2 installed. We want to upgrade to Windows Server R2 2012 with as little cost involved as possible. You can run the upgrade Windows 2012 Standard R2 of the disc on a Windows Server 2008 SP2 RC 64-bit environment?

    This issue is beyond the scope of this site and must be placed on Technet or MSDN

    http://social.technet.Microsoft.com/forums/en-us/home

    http://social.msdn.Microsoft.com/forums/en-us/home

  • Can we add this type on the Windows Server that comes with the Microsoft Action Pack subscription?

    Can we add this type on the Windows Server that comes with the Microsoft Action Pack subscription?

    Hello

    The question you have posted is related to professional level support. Please visit the link below to find a community that will offer in support of your request:

    http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  • Qosmio F30 audio driver for Windows Server 2008

    I'm only running a virtual machine with Windows Server 2008 installed. The server sees my Sound Driver, but it does not recognize it and ask for driver all the time. I tried running the installer of Sound Driver from the CD, but it didn't work, said: not supported operating system. I tried a driver all over the web and I found none. Can someone help to find this driver for me or let me know it it is possible to manually install this driver?

    I will be grateful for any help.

    As you probably know that Qosmio F30 is not designed to be used as a server and general support Toshiba doesn t Server2008. All you can do is to identify the manufacturer of the sound card and try to find the driver on its support page.

    Boyfriend sorry but that s all I can say about it.

  • I need lenovo G530 Driver for windows server 2008

    Hello

    I have a Lenovo G530 4666 series, I have installed the windows Server 2008 operating system and I can't install drivers.

    I need drivers for display adapter, sound and wireless LAN adapter

    Hello
     
     
    The Microsoft Answers community focuses on the context of use. Please join the professional community of COMPUTING in the TechNet forum below: +.
     
  • BSOD drives when adding T110 ii with PERC H200 and SBS 2011 or Server 2008 R2-

    Bought the server next in November 2011

    PowerEdge T110 II

    ManufDate: 24/10/2011 market: 06/11/2011
    RAM: 16 GB (4 x 4) 1333 mhz UDIMM DualRanked
    Processor: Xeon E3-1270 3.4 Ghz, 8 M cache, Turbo, Quad Core/8 t (80W)
    RAID: Map Perc H200
    Drive: 2 x 600GB 15K RPM SCSI 6Gbps 3 .5in - RAID 1 Mirror SA
    SBS 2011 standard x 64 (works on Win 2008R2)

    SBS 2011 installed without a problem and the server works perfectly since December 2011.  Backups occurring twice per day to a USB attached hard drive external 1.5 to and OS patches applied on a monthly basis without problem.

    Company need more storage so it wanted to add 2 drives more (same spec as to purchase). I thought to try to turn the RAID 1 pair in RAID 10 set in order to keep the simple logical configuration (a single large logical volume which now seems to be 1.2 TB in size instead of 600 GB) - could get but not really someone to describe if it could be done for non-destructive way that requires not the complete system installation/restoration - so opted for just add the 2 new drives as a RAID extra 1 pair in order to not reach a stable, boot, partition operating system running on the current RAID 1 pair.

    Contracted for the Dell technician to come out to install 2 new readers, be clear that the service was not complete until I had an extra pair of RAID 1, appearing as a usable operating system.

    Technician arrived, installed readers, set the new RAID pair in the H200 configuration utility, rebooted the system and when the BONES began to load had a blue screen BSOD. Technician then disconnected drives newly associated (the level of the cables) to see if the system would boot - BSOD again on restart (both of now get us this "pleated" feel if you know what I mean). Then went into the raid configuration utility, removed the new raid 1 volume (which, by the way, is appeared above the one existing in the list - which is not very intuitive that one that has been added is Volume 1 and the existing old is Volume 2 in the utility). After the triple-checking that we had the right volume (it showed that 8% initialized over the other which was complete, as well as the corresponding drive port numbers), we have REMOVED the new volume (at this point I don't remember if we had replaced the cables for the readers to perform this action).

    At startup the system rebooted normally - we were all so relieved, don't talk over retries at the moment.

    Talk to Dell there seems to be a problem with the PERC H200 firmware or drivers. Has not affected the config initial of a single pair of RAID 1, however caused problems when you attempt to add another pair. Escalation of Dell support said that has happened several times with Windows 2008 (which comes from the SBS 2011) systems. They recommended that the firmware update and the PERC H200 card drivers.

    I turned to the technician and asked when we could plan the updates of the firmware and driver and told him that they wouldn't do that (not sure that I blame the poor guy, he was sweating bullets after the BSOD 2nd).  I explained that we have contracted for installation services which included ensuring that the pair of extra disk appeared also usable for the operating system and he said that I needed to talk to Dell that.

    You wanted to post information on issues with PERC H200 BSOD when adding disks on Win2008 (or SBS 2011).

    Waiting for response from Dell as to who will come on-site to complete the installation.

    Any info about the question to know if the update of the firmware/driver will solve the problem or if I can do with reliability a disk 2 RAID 1 for a 4 disk RAID 10 conversion without having to reinstall/restore system would be appreciated.

    There is NO migration route TO or FROM a nested RAID levels (10, 50, 60) on one of the PERC H series, so it goes from 1 to 10 of RAID is not an option (without backup/replace/create/restore).

    Firmware release notes do not indicate that a large part is added (although the "bugs" may be enough):

    -Addition of Support for > 2.2 to SAS hard drives

    -Small bug fixes

    I have not seen/heard talk of this problem (I don't have a H200), but it is possible that an update of the firmware can change the way it handles the new disks, newly configured RAID arrays, or even how it presents to the OS.

    Do you know if the technician checked to see if the original VD was marked as boot VD?

  • PERC H700 driver during Windows Server 2012 r2 - disk Raid not recognized not

    Hello

    I try to install a r2 Windows Server 2012 to a Poweredge R710 with a Raid Perc H700. 2 HDD in Raid 1, but the HARD drive is not rcognized Italian Installation even if I try to use the 2008 r2 for the Perc Raid driver. They are listed, but if I select one disk HARD are not visible. What should do?

    Best regards...

    Grolle,

    Leave in the Raid Controller, what is the status of the table? In addition, was the raid 1 initialized after being created? If this isn't the case, then, who will have to be done before you try to install.

    If you download this and start on the lifecycle controller (F10) and then select deploy BONES, load these files there and proceed with the installation of the OS.

    http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=M5VGR&FILEID=3325059394&osCode=MWS80&ProductCode=PowerEdge-R710&LanguageCode=en&CategoryID=DD

    I would like to know how will install it.

  • Shared drive file Windows Server 2012 r2 access VERY slow

    Every time I open a file that is located in a shared folder on a drive with r2 Windows Server 2012 (videos and PDF with graphics, in particular), says file takes forever to load, videos often stutter, etc.. This affects all computers connected to the field with access to these shared folders/drive. Is there any solution for this? I couldn't find one so far.

    This issue is beyond the scope of this site and must be placed on Technet or MSDN

    http://social.technet.Microsoft.com/forums/en-us/home

    http://social.msdn.Microsoft.com/forums/en-us/home

  • HP deskjet 1050 driver for windows server 2003

    Hello

    Recently I bought HP DeskJet 1050 printer all in one.

    The CD not supported windows Server 2003 OS.

    If the supported drivers are available, then its good.

    Another option I tried was to install on Windows 7, but even this has not worked on.

    If the Setup error message it ' windows 7 ' was mentioned.

    No idea why it isn't install, a lot of work, but powerless.

    Please suggest if a patch is necessary.

    Thank you regarding

    Professional software

    Hi lvanhk,

    Download driver full of features, and then you should have the 7z folder mentioned in the document in my last post.

    Pilot and full features software

  • Debugging in kernel mode on network problem Windows Server 2012 R2 or Windows 8.1 comments

    Hi all!

    I tried the kernel debugger of network installation of client Windows Server R2 2012 on article according to VMware Workstation 10.0.1:
    http://msdn.Microsoft.com/en-us/library/Windows/hardware/hh439346 (v = vs. 85) .aspx

    But I can't connect to guest with WinDBG. I have set up bcdedit, restart and see that boot OS comments very slow.
    Then I run regedit, go to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\kdnet and see that
    KdInitResultString value is 'InitializeNetwork could get the Ethernet address of the host debugger.".
    KdInitStatus value is "c00000b5".

    I tried:
    -change of hardware to 9 version
    -change the comments to e1000 Ethernet card
    -disable the DHCP (debugger comments must use APIPA)
    -change the type of connection (bridge NAT, host-only)

    and every time I get the error "Failure of InitializeNetwork get the Ethernet address of the host debugger.". Guest 8.1 Windows x 64 and x 86 Windows 8.1 I get the same result.
    But I can debug comments Windows Server 2012 and Windows 8 on network without any problems. Also I can debug Windows Server R2 2012 on Oracle VirtualBox network.

    Is this a problem of VMware Workstation? Anyone can debug comments WIndows Server 2012 R2 or Windows 8.1 on network in VMware Workstation?

    Thank you!

    Have you tried the Workstation Technology Preview July 2014? (https://communities.vmware.com/community/vmtn/workstation/vmware-workstation-technology-preview-2014) I think that this problem has been resolved.

  • PROBLEMI WINDOWS SERVER 2012 R2 SU SERVER DELL PowerEdge R210 II PUMPS

    Ho downloaded the Immagine ISO della versione di prova dal portale di microsoft di Windows Server R2 2012, accendo it server accedo went fruit F10 by prima cosa ho tried a rates come sorgente CD my it sistema mi international it following message "do not find the catalog file. Make sure that the catalog Windows (R) and Dell (TM) update packages for Windows (R) are userd' o tentanto Reed selezionando FTP my it sistema mi international it following message "updates that you are trying to apply are not up-to-date approved from Dell.

    Potete darmi directions in merito. Grazie

    Buongiorno, io ho asked su information come procedere... No ho asked UN preventivo di spesa

Maybe you are looking for

  • Updated Java Plugin 8 45 (click-to-play), Linux has been blocked for your protection.

    I use kali linux OS and I've updated for mozilla firefox 40.0, but there are sites that requires the java plugin and when I tried to understand things, I came to this page with the message for security reasons, please tell me how to unlock it or what

  • I can't find the icon of Firesizer in Customize to add it to my main toolbar.

    I have the Firesizer Addon installed in Firefox (v. 29) and I tried to go in Customize to move my main toolbar as suggested in an article in Firefox, but it is not listed there. I can't find anywhere. It is turned on, so I don't know what else to do.

  • Satellite C855-10Z - speakers but no sound with headset

    No sound from headphones.Icon for headphones on Realtek HD Audio Manager on tab speaker becomes "BOLD" when headphones are connected (be colorful icon?). I have updated the driver and made a windows update.The headphones are not defective, as I tried

  • turn off options

    in the attached picture, button #1 is the stop button and below the table. How do I fix this error? the block diagram is also added.and there are several buttons. How to do when a button (#1) which is clicked by the mouse is active, the other buttons

  • formula with the global variable node

    Hello I'm tring using node formula with global variables as an entry and exit. but this is where I see the SW hangs forever. Either way, I am a novice to the labview. Can some give me advice why this is happening? Thank you in advance, Do