Driver USB PC/MAC Scanner Canon CanoScan LiDE 20 48-bit

Similar Questions

• Canon CanoScan LiDE 30 48 bit USB PC/MAC Scanner

  Does anyone know of a fix to allow me to use the CanoScan Lidfe 30 with my Windows 7 PC?

  There is workaround to VueScan 9

  It works well according to this Canon Scanner incompatible with Windows 7, 64-bit thread

• Scanner Canon CanoScan LIDE 200 works, MP Navigator EX 2.0

  Canon scanner CanoScan LIDE 200 works, mænd program MP Navigator EX 2.0 is op of hold that work, which has afinstaleret the and gen installed, a God until for a few days ago, there is no Ude which can help with works Igen MIG, pa advance tak

  Hello Erik,.

  Please select your language by clicking on the globe on the page down to the left to post your question in the language of your choice. If you can't find the desired below language, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

• Canon CanoScan LiDE 20 64-bit drivers.

  I have scanner CanoScan LiDE 20 Canon that I can't use because I upgraded my system to Vista 32-bit to 64-bit Windows 7. Is there a solution to this problem, as canon dose not provide drivers for this scanner 64 bit.

  N ° switch to Windows 7 32-bit or download a new scanner.

• Canon CanoScan LIDE 200 scanner not more known with the upgrade of the El Capitan

  Using my scanner USB Canon CanoScan LIDE 200 throughout the years that

  camera seems to no longer work after upgrading to El Capitan.

  The USB device ID is:

  Bus device 250 007: ID 04 a 9:1905 Canon, Inc. CanoScan LiDE 200

  
  

  What can I do to re - activate this device?

  Thanks for any help!

  Greetings

  ULI, DF4IAH

  Try VueScan http://www.hamrick.com/

• Het expensive Canon CanoScan Lide 60 moet ik een toepassing maken Hoe dat works

  IK heb het besturingsprogramma van een Canon CanoScan Lide 60 van site gedownload van, maar ik moet een toepassing maken om het expensive gun you use. Hoe dat works?

  IK heb het besturingsprogramma van een Canon CanoScan Lide 60 van site gedownload van, maar ik moet een toepassing maken om het expensive gun you use. Hoe dat works?

  Check with your manual Canon CanoScan Lide 60. Search, address, telephone number or Web site where you can get technical support.
  If you don't, here is a link where you can start clicking where you are and it will lead you to the site of the Canon Support in your country.

  Neem contact op put uw in Canon CanoScan Lide 60. Kijk voor het adres waar u technische support location site number.
  ALS I niet vinden good, yesterday is een link waar I moet door start you will op waar u bent het zal leiden tot een van uw support site Earth Canon u.

  http://www.Canon.com/support/

• CANON Canoscan Lide 500F Scanner USB with Windows 7 64 bit

  When I try to operate this scanner by pressing the scan on the scanner, Service Image Acquisition Windows tells me "there is no application registered for this event. The scanner using Canoscan Toolbox is recognized in the select the Source area, but when I press "select" I get "unable to select TWAIN source". I saw a lot of people have already had this problem but I have not seen a solution that works for me.

  BTW this mixture of languages bothers me a lot. Although my Windows 7 is installed in English, and although the English (US) is defined as my main input language, some programs insist to settle in French. I guess that's what we call "smart" software Sometimes I hanker after the silly software from the old days. :-)

  I would be grateful for any help.

  Hello

  Please follow the steps below.

  Method 1:

  Uninstall the printer software.

  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

  Method 2:

  Download and install the Twain driver from the link below.

  http://www.USA.Canon.com/Cusa/support/consumer/scanners/canoscan_series/canoscan_lide_500f#DriversAndSoftware

• Canon canoscan lide 60

  How to insyall my canoscan lide 60 scanner on window7 64 bit

  I tried and got a message saying scanner was a 32-bit

  snappers64,

  The correct software can be found here:

  http://www.USA.Canon.com/Cusa/support/consumer/scanners/canoscan_series/canoscan_lide_60#DriversAndSoftware

• Scanner Canon CanoScan 3000F color Image

  Now that I have Windows 7 I find that this scanner is no longer supported by Canon to update the driver. Is it possible to use this device or I'll have to, scrap it?

  VueScan now on the 3000F

  "VueScan works with the Canon 3000F under Windows.

  You must install a Canon scanner driver to use this scanner under Windows. Unfortunately, Canon has a driver for this scanner for Windows x 64. »

  The second paragraph contains the stumbling, because there is no installable driver of Canon for the 3000F.

  Many scanners is taken in charge by the pilots in Vuescan, but not all unfortunately...

• 64-bit driver for scanner Canon Canoscan 670u

  I recently bought a new computer with Windows 7. When you try to install my Canoscan 670u scanner, no TWAIN drivers were found. On this site I found and successfully installed a driver 64-bit for this scanner that someone else I work for the same scan in Windows 7: http://www.64bitdrivers.com/driver.php?id=1368
  I restarted with and without the scanner is plugged, but I always get the message that no driver is installed. In the device, clicking Properties, on the Canoscan Device Manager: the drivers for this device are not installed. (Code 28).
  Any help on how to proceed now would be much appreciated.

  Hi hmarcuse,.

  Your scanner is not compatible with Windows 7:

  http://www.microsoft.com/windows/compatibility/Windows-7/en-us/Details.aspx?type=Hardware&p=Canon%20CanoScan%20N670U%2048Bit%20USB%20PC%2FMAC%20Scanner&v=Canon&uid=7103A002AA&pf=0&pi=9&c=Printers%20%26%20Scanners&sc=Scanners&os=64-bit

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Canon Scanner incompatible with Windows 7, 64-bit

  I have a scanner, Canon Canoscan LIDE 30 that I LOVE dearly, and she doesn't have any listed driver that is compatible with Windows 7, either 32 or 64-bit. WHAT SHOULD I DO?  I don't want to throw it away or giving it!  I have to keep my old laptop to use it with Windows XP?

  "Tuscola_Dad" wrote in message News: 6a07e1f6-45ac-46a7-bf0f-26adb3d053c2...

  I have a scanner, Canon Canoscan LIDE 30 that I LOVE dearly, and she doesn't have any listed driver that is compatible with Windows 7, either 32 or 64-bit. WHAT SHOULD I DO?  I don't want to throw it away or giving it!  I have to keep my old laptop to use it with Windows XP?

  VueScan works a treat with the Lide 30.  I have one of those too, and it's the ONLY way to make it work...
   
  http://www.Hamrick.com/
  
  --

  Mike Hall - MVP Windows Experience
  http://msmvps.com/blogs/mikehall/

  Mike Hall MVP - Windows Desktop Experience http://msmvps.com/blogs/mikehall/

• Canon CanoScan N650U/656U/12200 Scanner

  Anyone know how I can get my scanner Canon CanoScan N650U to work with Windows Vista Home Basic? I reinstalled the software and did a search for drivers all without success.
  Any help would be appreciated.

  Thank you

  http://www.USA.Canon.com/consumer/controller?Act=ModelInfoAct&tabact=DownloadDetailTabAct&fcategoryid=351&ModelId=6858

  Read the link above and Select what you want drivers for operating system .

  There are No. Vista drivers available for your scanner model.

  Can written drivers for its products, not Microsoft.

  Time for another Scanner.

  See you soon. Mick Murphy - Microsoft partner

• Cannot open twain source - canoscan Lide 500F

  My scanner a CanoScan LIDE 500F, I can't analyze as it came with "unable to open twain source, please check the connection and restart the Toolbox. the connetion

  so fine so how to open the twain source? I am using Windows 7 on my computer to.

  Find out!

  http://weblogs.ASP.NET/jeffwids/archive/2009/11/02/Canon-scanner-unable-to-open-TWAIN-source.aspx

• Scanner install problems - Windows 7 (64-bit)

  Recently upgraded to Windows 7 (64-bit) and everything was fine until I tried to replace my flat bed scanner and are now trying to get two scanners work. First scan was listed (as was the second on the compatibility Web site) Scanner Canon CanoScan LiDE200 USB. Went on Canon's site and downloaded the Win 7 scanner software and installed (after removing the previous version). Tried running the software and got a message "memory" and has been unable to act. Went to 'devices' and 'right click' the scanner and was able to scan using the windows software, so scan worked. Original printer took over and bought an Epson v30 scanner, same problem, installed new software (Epson Scan 3.04). Doulble click on the shortcut of Epson Scan, but nothing happens.
  A scanner does not and I think it's the materials, but both makes me think it might be something else, please notify

  If Irfanview doesn't mean that you are 'Twain' drivers are the problem.

  I have a Windows XP roceedure that usually fixes this kind of problem, but have yet to try it on Windows 7. I posted it below in case you are interested, but go forward with caustion. Note that some of the steps/information I already posted, but I'll post the procedure in his entirerty.

  ---------------------

  If you connected the printer multifunction/scanner to your PC and then
  installed the printer drivers/software, the chances are very high
  the printer can operate but function scanner will not.

  Most scanners or printers of multi use require
  that you install the software before connecting the scanner or printer/scanner.

  Step by step instructions:
  (1) unplug the MFP or scanner.
  (2) uninstall the printer/scanner software and two pilots to help
  the Add/Remove Programs option.
  (3) look/search folders associated with your printer/scanner model
  contains "Twain" files, if the files still exist after uninstalling.
  Delete these files and related files.

  Note: In the list of files that is found you can ignore everything
  files listed in:
  C:\Windows
  C:\Windows\system32\...
  C:\Windows\ServicePackFiles\...

  NOTE: In the C:\WINDOWS\twain_32 folder: you have
  one or more files. The one of "do not delete" is called: wiatwain.ds
  (wiatwain.ds is installed by Windows XP)
  All files in this folder were likely created when you
  installed the printer/scanner. Check each of the files 'Properties' and if has the
  brand of your scanner (Epson, Canon, HP, etc.), identified as the
  company/brand, these files can be deleted safely.

  On my PC I have my scanner HP twain file located in:
  C:\Program Hewlett-Packard\Precisionscan Pro 3.1\TwainCtrl.ocx
  There should be something similar on your PC, so in my case at least
  I would like to uninstall the software of Scanner HP and if it ' file TwainCtrl.ocx
  is still there after you have uninstalled the scanner software I would delete it.
  I have also a second that the file named "Twain_32.dll" TWAIN located:
  C:\Program Files\Adaptec\Easy CD Creator 5\PhotoRelay

  (4) check the Device Manager and remove all the entries if necessary.
  (5) create a Restore Point
  (6) analysis the registry using the name of brand/make of the scanner as a keyword for
  image search. (Remove all entries are, but make sure it's a connected scanner entry)
  7-restart the PC and check once more the Device Manager.
  It should not show any announces the printer/scanner.
  (8) now reinstall the software and two pilots.
  (9) shut down the PC.
  (10) the PC power turned off, connect the printer/scanner, then
  restart / Windows startup.

  Note: Sometimes there might help you try a different USB port if you
  printer/scanner is a USB device.

  An easy way to test your installation of the twain driver software work, s
  is to use a graphical editor named IrfanView.
  http://www.IrfanView.com/

  If you download, install and run this software,
  located in the menu bar is an option named "file".
  By selecting the 'File' option, you should find a
  (near the bottom of the list) option for named:
  'Select the TWAIN Source', click this option
  and then a popup should display valid Twain sources
  for scanner you. If you see your scanner from the list,
  Select it, and then try to scan an object (picture).

  By selecting the Twain Source in the file menu IrfanView should load
  your scanner software and then scan.

  If you choose the option "Copy Shop" also in the file menu you have the
  possibility to bypass your scanner software and directly scan a photo in
  IrfanView. Try the option "Copy Shop" and let me know what happens.
  Note that "Copy Shop" list of your Photo editing/scanning scanner
  software and hardware name (make and model) of your scanner when
  you click on the button "Select Twain Source" of the photocopy shop.
  You should choose the scanner hardware option.

  For example, on my PC the software Photo retouching/scanner is named:
  «HP Precisionscan Pro 3.1 "»
  The second entry "Twain list select the Source" Copy Shop is my scanner
  brand / model that shows that:
  "WIA-HP Scanjet 5470 C 1.0"

  So for me when you use Copy Shop, I select the second entry when
  prompt to select the Twain Source.
  I then check the 'Twain with the preview.
  (I mark this option if the scanned image does not directly)
  to the printer, but on the contrary is displayed in IrfanView).
  Then I click on the button 'start' location has the lower part of the photocopy shop
  window to start the search.

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• Scanner CanoScan Lide 70 Canon does not load on my new windows 7

  I have a new computer EliteBook hp laptop with windows 7 and I can't connect my Cannon CanoScan LiDE 70 scanner... Why? Can someone help me with this?

  At t quick glance resembles driver support stops at Windows XP.

  How old is this scanner? Have you checked to ensure compatibility with Windows 7?

  Compatibility Center says it's! http://www.Microsoft.com/Windows/compatibility/Windows-7/en-GB/search.aspx?l=en-GB&type=hardware&s=Canon%20CanoScan%20Lide%2070