Driver video error Code 10 after the upgrade to Windows 7

Upgrading to Windows 7 & have the following error messages:

Standard VGA graphic card work not only can not start (Code 10)

Converter USB - LAN has no driver

SMA 851 X USB to Fast Ethernet Adapter

During the initial installation of Windows 7 the monitor works but when Windows upadates are applied it gives the messages described above. Everything worked then on Vista... but also Vista would work!

Dell does not have a driver for a monitor solution - 2 years. I was running as an extended desktop on a Dell Inspiron 6400 with 2 GB of RAM, new 500GIG Hitachi hard drives.

Also cannot load the Office Small Business 2007 Business Contact Manager.

Hi remaxguy,

See the following article on setting error Code 10:

http://support.Microsoft.com/kb/943104#appliesTo

I hope this helps!

Debra
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think

Tags: Windows

Similar Questions

  • This connection is untrusted with error code error code: mozilla_pkix_error_v1_cert_used_as_ca) after the upgrade to Version 38 for my Web site.

    My site works fine with Firefox 35 version without any problems. but when I upgraded to version 38 I started getting the error code: mozilla_pkix_error_v1_cert_used_as_ca). I checked my certificate and is valid until the end of the year

    There are hundreds of variations within each major version of Firefox, so the cause of the problem might be hard to guess without more information.

    You want to post the URL of your site?

    If not, you could generate a report using this test page: https://www.ssllabs.com/ssltest/. Which often will identify the problem that Firefox has with the certificate.

  • HP Pavilion Notebook 15-p050ca: graphics driver error message started after the upgrade of Windows 10 model installed on #: G6U13UA #ABL

    I have recently upgraded to Windows 10 and since then, I received the following message through a game: "display Intel HD Graphics driver Driver for Windows 8 (R) stopped responding and has successfully recovered."

    I checked my graphics driver and it says that it is up-to-date.  I tried installing the latest drivers for my laptop model (according to the HP drivers page), December 15, 2015, installed without a problem, but no version has not fixed the problem.  An error message appears when I try to install the March and April, 2016 versions of graphics drivers, claiming that they are not compatible with my computer.

    I also tried the Intel and HP driver update utility and told me that my drivers are up to date.  However, when I look at the properties of my Intel(r) HD Graphics Family in Device Manager, I noticed that information on the events tab says: "peripheral PCI VEN_8086 & DEV_0A16 & SUBSYS_227E103C & REV_0B\3 & 11583659 & 1 & 10 still requires the installation."

    I don't know what needs update on my computer or if this driver is incompatible with Windows 10 and there is not yet an upgrade?  Advice or opinions would be appreciated!

    My computer model is the 15-p050ca HP Pavilion Notebook PC (ENERGY STAR) model #: G6U13UA #ABL and the graphics driver is version #: 10.18.15.4279

    I went back to 8.1 for Windows and ran the store several times and then reinstalled Windows 10.

    I watched the graphic version installed and version 20.19.15.4331 dated dated 18 November 2015, but he still claimed there was an update of the graphics driver.  I tried the update and it was version 10.18.15.4279 dated August 2015, which was the same version that was installed when I had problems (and the same version on the HP website), then I went back to the 20.19.15.4331 version.

    I tried all the graphics drivers listed for my computer on the HP support page and again, I had the same problems with them as I had before (either claim that my computer has no minimum requirements or my graphics driver crashing).

    With the current version (20.19.15.4331), my graphics driver has stopped at least for now crashing, but I assume that this is not a specific driver HP and is only based Intel?  If so, I recommend HP glance on the issue, I've had if they claim that these drivers are supposed to work for my computer when my computer is, in fact, not accept them.

  • How can getting error Code U44M1P7 during the upgrade, I fix?

    How can getting error Code U44M1P7 during the upgrade, I fix?

    Update product that you are trying to install?

    Is it compared to the creative or perpetual clouds?

    Please check following if you have creative clouds.

    http://helpx.Adobe.com/Creative-Suite/KB/error-u44m1p7-installing-updates-CCM.html

  • Laptop Compaq CQ58: LAN Ethernet does not work after the upgrade to windows 8.1

    After the upgrade of Windows 8 to 8.1, my Ethernet LAN is no longer in effect. Wireless LAN connectivity is OK. I run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I don't see a listed 8.1 for the LAN Ethernet driver.

    It seems that you encounter the same problem, I did when I ran the free preview of the W10. I had this error on the card reader.  I have no idea how to solve this problem.

    Is there is no ethernet controller needing drivers in Device Manager, then it is probably the realtek lan adapter that has the number 12 of the code, or it is part of the motherboard that controls the ethernet adapter.

    If you need Atheros bluetooth driver, then this is probably the one you need.

    http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_127984_1

    Unfortunately, I won't be able to help you with question 12 code or ethernet.

    IMO, they are insoluble.

  • HP Photosmart C6280: cannot print on C6280 wireless after the upgrade to Windows 10

    Cannot print on C6280 wireless after the upgrade to Windows 10. Have removed the device, but try to re install the printer when is not found. Can print if I connect USB. Tried to reload the driver using HP Support software help, but when he arrives at the end of the download fails.

    Hi @Ron9871,

    Welcome to the Forums of HP Support!

    I see that you are unable to get your printer HP Photosmart C6280 wireless printing. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

    I would like to try the steps in this guide, "offline" Status Message printer (Windows 10).

    If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

    • Print a Page of Network Configuration menu of the printer front panel. Note: the IPV4 IP.
    • Type the IP address in the browser to bring up the SAP.
    • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
    • Select Manual IP.
    • Enter your IP address manual (192.168.0.232)
    • Enter 255.255.255.0 for the subnet mask, except if it is different.
    • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
    • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
    • Click on apply.

    Please restart the router, the printer and the computer in this sequence.

    If you're still having problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

    What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

    You can try to change your WSD printer port by a Standard TCP/IP port.

    To do this, you will need your current IP address printers.  The Network Setup page shows the parameters of network for the product. To print this page; Press the button of network () on the control panel of the product.

     
  • After the upgrade of Windows Windows 7 10, could not recover my product key.

    Original title: windows 7

    After the upgrade to windows 10 windows 7, could not recover my product key. When I connect my system am get notification that you may be victim of software counterfeiting and copy of windows is not genuine. you do me too much this error code. 0xC004F057. Please help me to recover my product key. my windows does not work after the upgrade as well.

    I suggest that you run the diagnostic tool Microsoft Genuine Advantage in normal mode and copy and paste the results into a response for further analysis:

    http://go.Microsoft.com/fwlink/?LinkId=52012

    Run the tool and when it ends, click the copy button, open a text such as Word or Notepad file and select Edit, paste. You can paste directly into an answer here. Open a response, right click and select Paste.

  • HDR and Panorama fail after the upgrade to Windows 10

    After the upgrade to Windows 10, trying to merge pictures gives the message "unknown error occurred".  After the first attempt, I've updated my driver graphic card, and HDR worked.  But the next time, the error message reappears, and this has been consistent - if the graphics card is engaged or disabled!  My graphics card is NVIDIA GeForce GT 750 M.

    The problem turned out to be unrelated to Windows 10.  For reasons I can't understand, it is limited to one set of photos taken on a single morning. So, no problems with Windows 10.

  • Volume controls on the keyboard after the upgrade to Windows 8

    I have a Touchsmart 520-1070 with the mouse and keyboard without wire factory.  After the upgrade to WIndows 8, the volume controls no longer work.  I tried the Recovery Manager to reinstall the keyboard drivers, but there is no driver keyboard under hardware drivers.

    In the following device manager are listed under keyboards:

    HID keyboard device

    Keyboard 109 MCIR Microsoft eHome

    Keyboard MCIR Microsoft eHome

    Microsoft eHome key remove control Keayboard

    PS/2 standard keyboard

    Any report that they are installed and are working correctly and that the drivers are up to date.

    Has anyone else seen or solved this problem with a Touchsmart computer?

    The instructions below were provided by HP support.  This has restored the function on the keyboard volume controls.  The referenced below drivers are drivers IDT high definition Audio Device.  I am not sure that it was necessary to reinstall the audio drivers.  It can only had to remove the USB dongle and back to restore the functionality of the button.  Note: the USB dongle is located behind the VESA Panel to the back of the PC.  No tools are required and the dongle can be removed and replaced without shutting down the PC.  VESA panel removal requires a bit of a steady hand, pulling the lip which is close to the connections on the rear panel.

    Instructions received from HP:

    Please go to the following link and check the "return of the system", article #7 is the USB dongle:

    http://support.HP.com/us-en/document/c03026390

    After you have reinstalled the receiver, please download and install the following driver:

    http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-110499-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

    Then install the following update:

    http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-112060-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

  • After the upgrade to windows 7, Warcraft3, Battlefield Viet Nam cannot run in 4:3 screen but 16:9

    After the upgrade to windows 7, Warcraft3, Battlefield Viet Nam cannot run in 4:3 screen but 16:9... my East of 1366 X 768, so the games are run with black screen on the left and right sides... What can I do? He has run well in Vista =]

    1366 x 768 is the strangest resolution that I've ever heard of. Your video card drivers helped "keep the proportions" and decided to not to stretch imagine because I assume that you can't choose this exact resolution in the game. If your monitor has an overdrive video or image format option, you can enable or disable that or if you have a NVidia card, you can change the picture format option in the properties of the video card.

    If you have an ATI card, then you're stuck with a proportional image: P

  • My laptop camera image on the upside after the upgrade to Windows 7 Professional 64-bit.

    I have a laptop Asus G50Vt - X 1, which is a 64-bit computer. It had Windows Vista Home Premium 64-bit installed on it and the unit worked properly with him. I ran the update of Windows 7 Advisory on this matter and he said I could upgrade to Windows 7 64 bit. After the upgrade to Windows 7 Professional 64 bit the images from the camera are all upside. I contacted Asus about the problem and they sent me the drivers updated, but the images are still upside down. Pourrait Windows 7 cause this problem as I know that it worked fine under Vista?

    I also noticed that my dvd/cd player and external hard drives don't stop the execution after that I have quit an application. When this happens, I can't eject the cd or remove the drive from the computer.

    Windows Update has nothing to do with the upgrade of Windows. Post future questions in one of these forums, please: http://social.answers.microsoft.com/Forums/en-US/w7install/threads

    http://social.answers.Microsoft.com/forums/en-us/w7hardware/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Missing graphics drivers after the upgrade to Windows 8?

    Hey guys,.

    I see several people on the forums of the problems with graphics drivers not installed after the upgrade to Windows 8.

    The first step you want to take, make sure that the laptop is supported by Windows 8.

    You can go HERE and see if your laptop has been tested for Windows 8. If she's GREAT!

    Now, if you're still looking for the graphics drivers according to the processor you have there are several places to look.

    First of all, you want to check the HP website and your product type # in the next selection > and then select the operating system > click Next > and look under the section that says "Driver - Graphic" and start the download.

    If you still don't see the driver referred to in this article, you can see one of these sites according to what processor you have.

    INTEL

    AMD

    Also, if you have Windows 7, you can still follow this post.

    THX

    I hope it's useful!

    THX

  • Cannot connect to internet after a reboot before you uninstall and then reinstall the network card. (After the upgrade to Windows 7 from Vista)

    This problem started immediately after the upgrade to Windows 7 Ultimate (32 bit) to Windows Vista Ultimate (32 bit).  Again, I want to remind that I never had this problem before installing Windows 7.

    -After a reboot, I am presented with the impossible to connect the network indicator (yellow triangle with!) in the task bar.  (It was how I was welcomed after the installation of Windows 7 is said by the way).

    -The only way I found to regain connectivity is to uninstall and reinstall the network via the device manager card, date at which the computer always successfully connects and remains connected until the next reboot.

    Network card: Realtek RTL8168C (P) / 811C (P) Family PCI - E Gigabit Ethernet NIC (NDIS 6.20)

    Driver provider: Microsoft
    Driver date: 14/05/2009
    Driver version: 7.2.1127.2008
    Digital signer: Microsoft Windows

    Thus, we have solved the problem! There are two possibilities of your problems:
    1 company Adobe uses the Bonjour service , this service should be disabled.
    Computer > Manage > Services and Applications > Services => find the bonjour service (sometimes stated as long numbers), stop service and if the Disabled value. It works!

    2. If it is not signed as Bonjour service. Try to disable the service:
    Shutdown mDNSResponder .exe (he is represented by # Id_String1.6844F930_1628_4223_B5CC_5BB94B879762 #).

    It is installed with Adobe software. If you upgrade the Vista, it will generally many users problem!

  • DVD player not recognized after the upgrade to windows 8

    I write this to document some odd behavior, that I lived after the upgrade to Windows 8 in the hope that it might save some grief for others.  Of course, if someone could explain why this problem occurs, I'd be very interested/grateful for an answer.

    I recently updated my computer from Vista Ultimate to Windows 8.  I did a clean install of Windows 8, because there is nothing special about the machine I wanted to preserve.  In all cases, the upgrade went without a hitch and I was soon back up with Windows 8 as my OS (I really like, btw).

    The only oddity I noticed after the upgrade is that my DVD drive was not recognized by the operating system.  Remember, this is the same DVD player that was used to install the OS, so I found it rather peculiar.  After a bit of lost time, try software solutions theoretical I started to play with the equipment.

    My motherboard is an ASUS M3A78-EM.  My hard drive is attached to the SATA1 port and my DVD player is plugged into the SATA2 port.  I removed the DVD drive from SATA2, plugged into SATA3, restart Windows 8 (from HDD on SATA1) and Windows 8 now recognizes the drive!

    I thought it was really weird, so I stop, put the DVD on SATA2 drive, rebooted, and the drive was no longer available in Windows 8.

    OK, so I thought that maybe the SATA2 channel was bad (even if he had worked at the Windows 8 DVD installation, just an hour or two before), so I put my HDD on SATA2 and the DVD drive on SATA1.  After doing this, Windows 8 start very well (so there is nothing wrong with SATA2), and it recognizes the DVD on the SATA1 drive.

    OK, so I did that for a while, and virtually all combinations I tried worked as long as the DVD player is not plugged in SATA2.

    I cannot live with that, but thought it was really strange.  Also, I note that the old operating system (Vista) was acknowledging the same DVD player while it was plugged on SATA2.  This leads me to believe that the problem has something to do with Windows 8, but I can't imagine what could be the cause.

    Thanks dude.  After you create this registry key/value and restart Windows 8 was able to finally see my DVD drive on SATA2.  =)

  • After the upgrade of windows (Pinball) 10, when working in Lightroom adjustment brush is not making changes, it is there but it does not work.

    After the upgrade of windows (Pinball) 10, when working in Lightroom adjustment brush is not making changes, it is there but it does not work. Also several times when I go to the library to develop fashionable mode, programs stops. I am really frustrated. Help, please.

    Also several times when I go to the library to develop fashionable mode, programs stops.

    It is often a symptom of an incompatibility between LR and your video card.  If the other suggestions don't help you, go to System Preferences > performance and uncheck use Graphics Processor.

Maybe you are looking for