DSC-HX90V/B does not connect via Wi - Fi for my MacBook Pro under El Capitan!

Similar Questions

• Satellite M30-106 - does not connect via radio

  Hello
  hope someone can help im having headache with my Satellite M30-106 problems

  I can connect to the internet via ethernet, but once I delete it does not connect via radio. I am trying to connect to a router broadband Sagem sky but for some reason any he just not going, when I open wireless connections, I can see the projection of router as safe but just cannot connect.

  I would also like to point out I am very new on wireless and to be honest, I don't know what im doing please give me advice in simplistic terms you can so I can be sure I understand where im going wrong

  Regards wayne

  Hello

  If you try to connect to your router, you will ask for a password or what exactly is going on?

  Maybe you should try to update your laptop WLAN driver. You can find it on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online downloads support & -online Download Driver

  Also make sure you use the same WiFi standard that you have configured on the router, for example 802.11 g.

  What operating system do you use? Have you installed all service packs and patches?

• My Mac Pro and HP Deskjet 3070 PowerBook does not connect via a wireless network from dorm

  Both my laptop and printer (an all-in-one) are connected to the same wireless network dorm, but they do not connect on it.  They connect only wire using a USB cable.

  I have for the MacBook Pro and the Deskjet printer IP addresses but no way to use to establish a connection.  I don't have access to the network router.  When I test the connectivity, the software tells me, "too many networks."  He can't make a choice!

  Interestingly, I have my MacBook Air along this journey, too, and the two MacBook have no problem of communication on the same network of dorm.

  Is it possible to plug these devices such as computers connect or should I remain attached to the USB cable to use my new printer?  I guess you know how I feel about this.  Thanks for your advice.

  You are right.  There is no way to bypass security protected by password and thus to connect a Mac to a Deskjet 3070 via a secure network without access to a router, and a password.  However, even without access to a network or a router, there is a workaround solution.  In my case, where the technical ability to correctly configure the router and the printer is beyond the understanding of the management of the dormitory, qualified through the difference to happen anytime soon, it is the answer I need.

  The solution is to build your own Mac + network printer and make it private, protect it against unwanted entry.  This offer you little mobility in the area of the printer, which is much better than nothing.  A sofa can be more conducive to creative thinking as an Office Chair.  The unconventional twist that Johnny introduced the user, the printer that generates the sender-recipient, not the Mac network.  Very smart.

  I refer you to the thread,

  "Deskjet 3070 cannot connect to the ad - hoc network (Mac)"

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/DeskJet-3070A-cant-connect-to-ad-hoc-network/m-p/1446819#M38598

  Then the only question is to know how to connect your Mac on the Deskjet 3070 printer via the generic (as he calls it, "ad hoc") network created by the Deskjet printer.  The Mac has abundant features for this purpose.

  Thanks for the categorical assertion, however.  No sense to break down the walls looking for a nonexistent hidden tunnel...!

• Bought LR6 DVD but the installer does not connect to the internet for I can register it.  I downloaded the trial version to work around this problem, but I can't get the program to start.  I get the same message that I should connect to the internet and c

  Purchase DVD LR6 Adorama, but Setup does not connect to the internet so that I can record.  Internet works fine.   I have Adobe account.

  I went to Safari to Chrome and downloaded the trial version in the hope to bypass the DVD version, but I can't get the program to start.    I get the same message that I should connect to the internet and connect.  It seems impossible after 3 hours.  Spent an hour chatting with the support of the India.

  Also remove the cookie file and reg Lightroom then enter the serial number and check.

  Windows:

  Press Windows button (located between Ctrl and Alt buttons) with the key R together at once, you will get a command window.

  Type below command and press the enter"" key.

  programdata %

  It will open the ProgramData folder. inside locate Adobe folder.

  Go to Adobe > Lightroom.

  Open Lightroom and delete all the files inside,

  Then run LR 6 and enter the serial number,

  Mac:

  (1) right-click on the icon in the Finder, then select the 'Go - To Folder' option.
  (2) you will get a text box, type in the following command and then press the 'return '. (" Do not miss ~ symbol" "')

  ~/Library

  It will open the folder of the user's library.

  (3) then navigate to Application Support > Adobe > Lightroom.

  Open Lightroom and delete all the files inside,

  Then run LR 6 and enter the serial number,

• OfficeJet 7500 a large format does not connect via Timecapsule

  I have a Mac Book Pro running Mac OS X 10.7.5 (just updated all the software).

  I connect my MacBook to the internet through my Apple Time Capsule (wired connection). I use version 6.1 (610-31) Airport utility and I just updated the version of the firmware to 7.6.1

  I use a local wireless through my Time Capsule.

  I just bought a large format HP Officejet 7500 a (model name: C9309A).

  The printer has been set up to detect my wireless LAN and initially he worked for printing and scanning, but it has recently discontinued. I tried to uninstall (purification) the software of my laptop HP, all my software update and reinstall the HP software on my laptop, but it still does not work.

  The printer is connected to my time capsule via an ethernet cable and a USB cable. It also includes Wi - Fi connection generates my time capsule. I have preferthe printer plugged into the router (time capsule) rather than a WiFi connection I print large files.

  I can install the printer on my computer mac laptop (settings/printers & scanners). I added it as a wireless and a wired connection through my time capsule (it shows that the connection is done by the time capsule). However when I print, there is a long delay, the printer now says "printing", but I get the error on my laptop screen "can not write print data: ÿ * xˇ.» A few minutes later a blank page or a page with a single line is ejected from the printer.

  If I go into the configuration of the HP printer, it says I'm under pilot 3.4.1. If I try to open the printer utility I get a message "utility HP does not work with the devices connected to the airport. Try to connect the camera directly to your Mac to work with her. " I tried to connect directly to my Mac via the USB cable and which does not work either. I prefer that the printer is not connected directly to my laptop I have few USB ports.

  In my view, this printer is supposed to be compatible with my system.

  Is there something more, that I can do or this printer is not compatible with my MacBook Pro or my Time Capsule?

  Hi marion_13,

  Turn it on wireless and then try to access the EWS - embedded Web server by typing the IP address of printers in the browser's address bar Safari. I would like to know if you are able to access the built-in Web server?

  Document below will also help you get the printer installed on your wireless computer.

  http://support.HP.com/us-en/document/c02239420

• HP Officejet Pro 8500 has 910 a, Vista 32-bit, does not connect via the usb port on my PC!

  I used to have it all in one connected to my pc, until I lived some printing problems, so I decided to uninstall it!  When I tried to reinstall, the pc will not connect it.  I tried different ports and have replaced the cable, have also downloaded the latest software and drivers all to nothing does not.  I can connect wireless to my laptop, but unfortunately is not a solution for my office because it is not wireless, so it must be connected via USB.  At my wit's end, please help me!

  Hello

  Can you try to insert a flash drive into one of the USB ports on the printer, to make sure she reads it?

  The printer port may be what gives you the question. In addition, you can try the USB printer connected to another PC?

  Let me know the results.

• OfficeJet 7410 does not connect via WiFi and will not scan

  I don't know if this post is in the right place, but here goes:

  I have a 7410 OfficeJet that was connected to my home network so that I could print/scanning wireless to it from any computer in the House.  It worked well for a while.  I am running Windows XP SP 3.

  We lost power for a few days during the hurricane (Fortunately it was our one central issue), and when the power was restored the 7410 wouldn't connect to the wireless network (we have FiOS).  I checked the unit identifies the correct system ID (and I entered the WEP key), but when I try to install from the desktop computer, it can not find the 7410 (laptop computer also was not able to find the 7410).  The only way I could get the desktop to detect the 7410 is to connect it to the router with an ethernet cable (it does not work with the laptop).  I also can't connect to the wireless printer if I put the IP address in my browser (I'm able to do when it's connected via ethernet).  Not sure if it is a firewall issue.

  When the 7410 is connected to the router with the ethernet cable, I could print to it without any problems.  However, I can't scan from it.  When I try to scan, I get the error message "when trying to scan, could not find the required user interface file (Please reinstall scanning software).  I uninstalled and reinstalled the HP software, but I still get this message.  I also followed the instructions here: http://support.hp.com/us-en/document/c00516936 but that has not solved the problem.

  This morning, I uninstalled the printer with the hope that, put it back in place could solve the problem of scanning, but now the computer is not able to find the printer, even if it is connected by ethernet.

  I hope I gave enough information.  Ideas/comments/suggestions would be appreciated.

  I think I see what's happening. You just need to reestablish the connection to the printer wireless. The document below should help you with that. Once you have done so, the software shouldn't have a problem connecting to the wireless printer.

  Installation of the software of the printer on a wireless network or network (Ethernet) cable

• Canon printer does not connect via the IPP Protocol

  I work in a company that sells printers offices/schools/etc. Yesterday, we received a call from a customer indicating that the Copier, we sold them connected not to a new computer they bought.

  I went to the site and noticed that the computers in question were all purchased during 3 months and all loaded with Mac OS X El Capitan. Most was registered on 10.11.3, and some 10.11.2 and 10.11.1. All computers work turned Yosemite.

  We receive a message somewhere in the sense of "Communication error. This printer may not be able to [print], you want to save it anyway? »

  It was a cannon imageRUNNER Advanced C5235. The client declares that if he saved the printer, it would not be able to print, but would still see jams paper, messages and other statutes of the computer printer toner. After attempting to remove and reinstall the printer using the most recent driver available on the Canon Website, we received the same error, the customer received. We escalated it to Canon support, who asked us to choose LPD instead of the PPI for the Protocol, allowing the printer to you connect and start printing on all devices running El Capitan.

  After further research, to my knowledge, the ISB is more recent and has more features that the LPD, although I couldn't find much on it so I was uncertain about the origins of these two protocols, except that they were introduced in the 1990s. I know it's kind of vague, but is better/more recent than PPI LPD? If so, great. Otherwise, is there a way to solve this problem and get computers that run El Capitan to connect correctly using IPP?

  The problem here is that the driver Canon UFR2 or PS that was used on the Mac to print in ADVANCE of Canon C52xx does not support PPI. This is why you must use an alternative Protocol.

  Note that it is possible to print to the C5255 using the PPI, but you need to use the Canon PPDs which means the copier must have the kit installed Postscript printer and you get not the pretty picture base views the pilot UFR2 and PS to give you.

  Second point is that the Canon UFR2 and PS drivers, it is preferable to use HP Jetdirect-Socket to the LPD protocol. He sent larger packets and verifies the status of the target unit - LPD simply sends data to the fixed IP address so if the printer has a problem you don't get this information until you walk up to the photocopier.

  I hope this helps. Answer if you need more information.

• New Mac Pro does not connect via WiFi to my ATT router.

  I have a brand new Mac Pro garbage but I'm unable to get it to connect to my ATT wireless router. My phone, the laptop and the TV do it but not my main computer. Oddly enough, I AM able to connect via WiFi for the Mac Pro to my laptop. Any suggestions?

  Please post your question in the Mac Pro support forum... Mac Pro

  If you have a question about one of the Apple routers... the AirPort Express, AirPort Extreme or Time Capsule airport... the products pictured below that we support in this forum... we can probably help you.

  

• EAS does not connect via wifi company post - 1.3.5

  This seems to be a somewhat different issue of EE that some know, so it was recommended that I start a new thread. My question: I can access is no longer to EAS via the wifi of my company. It worked before 1.3.5. If I turn the wifi off, I can then connect EE without problem. I get no error when connected via wifi, rather e-mail and calendar just don't update.

  It turns out that our firewall is configured to disallow connections since our internal wireless to internal resources through external access (that is, accessible through the Internet). This explains why it is not working currently - other devices exhibit the same behavior, including iPhones and laptops.

  The question then becomes: why it worked before? I can check before 1.3.5 I can be connected via wifi to my company and still connect to the Regional service. So the previous version tried to connect via wifi, then when he could not, did he switch to EVDO to connect?

  If this is the case, then it is a very nice feature and it would be great if it was turned off. If it is not the case, then I have no idea why it worked prior to 1.3.5.

• ORACLE12c PDB does not connect via IP to cluster

  Dear all,

  DB version: 12.1.0.2

  OS version: Linux 6

  DB active IP: 192.168.10.101

  DB passive IP: 192.168.10.102

  Cluster IP: 192.168.10.103

  We try using linux os cluster active/passive database installation. In the earlier version (11g), we have 2 public ips and a single cluster ip and we will provide the IP address of the cluster in the listener.ora so that users can connect via IP to cluster.

  12 c, the container database connects via an IP cluster but the pdb1 is not connection and launch ORA-12514.

  USE_SID_AS_SERVICE_LISTENER = is on the plateau in the listener.ora

  Please note that we were able to connect to pdb1, when you provide us with in the listener (101 or 102) public ip address.

  Please let me know if there is no change or the way the DB (pdb1) service connects differ?

  Kind regards

  Anand.

  Hello

  local_listener is defined in your database of 12 c pointing to the ip address of cluster?

  You can share the lsnrctl status output?

  See you soon,.

  Rich

• Muse does not connect to the catalyst for business

  When I go to publish my site on BusinessCatalyst, it says that my connection with Adobe has expired. I have signed in one off, uninstalled and reinstalled creative cloud and still not connect. Help me!

  In the last 24 hours "publish on business catalyst" no longer works. "An unknown authentication error occurred using your Adobe ID - check your network connection and try again.
  Looks like that Business Catalyst has moved from a free preview of accommodation to a plug-and-play full hosting / e-commerce site. All of a sudden there are inscriptions and pricing, and I have no idea how to use.

• Why does not load Lightroom 5 DVDs on a Macbook Pro?

  I tried to install on my old 17 "Macbook Pro running 10.6.8 5 Lightroom. 5 LR has informed me that he could only be installed on 10.7 or higher. I have updated my OS Lion (10.7.5) and tried again. Now, when I insert the DVD of 5 LR there in a moment, while the MBP is a few quiet noises, never of the towers, and then it spits out the rear DVD. Help! WHY is that what it's doing this? It support and showed me a Setup screen when I had the old OS running - but now the DVD does not load!

  Worse still, my LR2 hangs everytime I try to rebuild some web galleries - so I'm well and truly stuck, unable to make promised to work for a client and shed tears of frustration. Adobe (or someone) - Please, please help!

  You can try to download and install this way...

  Adobe - Lightroom: For Macintosh

• After that the effect does not recognize my AMD Radeon r9 M370X (macbook pro 15), what can I do?

  I just bought my macbook pro 15 inches with the graphics card (AMD Radeon r9 M370X with 2 GB of VRAM) and Adobe CC is not recognizing, WHAT can I DO? Help, please!

  Your screenshot shows that After Effects is thankful your GPU very well. The OpenGL section shows that OpenGL works normally. AMD cards like yours have CUDA, so the CUDA section is empty and the ray-tracing section (which depends on CUDA) shows the same.

  Don't worry CUDA; It is used only for an obsolete feature, the 3D rendering engine traced to the RADIUS. The page that I asked you to read above explains everything in detail.

• 2540 all-in One: 2540 printer does not connect via radio

  Dell Inspiron Windows 8.1 64bits, lesst of one year

  HP 2540 all in a Priner single, new, right out of the box

  Router NetGear WGR614 v9 (2008?)

  Unable to connect wireless.  OK, via the USB port.  Need a wireless connection.  Doctor Scan is without help.

  Who did. Thank you. I do not understand why IT worked, but it setting up wireless initially failed. It was VERY frustrating. I was ready to trash this abiut printer.

  P.S: it prints very well. Photos of ESP. My children and I are very impressed.