Duplexing on Photosmart 6510

Similar Questions

• Photosmart 6510 straight cut of the page

  Hello

  I'm on a macbook with OSX 10.5.8 with a Photosmart 6510.

  Installation went without problems, but when the right side of the print documents are cut despite the margins are the same on all sides.

  Subject of PDF, it seems as it should, it is not simply print as it should - miss me the right +/-1 cm from the paper.

  PS

  Also I would like to print aligned in the Middle, which - however - perhaps a Preview of Mac problem. However, ideas are welcome...

  I already tried all these things, but I discovered as the duplex unit being a little strange ITMIS. I noticed that it cropped only the last printed page - so I just added 2 empty pages at the end and it worked.

• Photosmart 6510 does not print in black

  My photosmart 6510 does not print in black. I presume that it was the cartridge but I replaced the cartridge and it still does not print. I cleaned the print heads and the cartridge ink levels are full.

  The printhead, cleaning of the screen failed touchscreen printer running.  But when I sat down at my computer and used the program utility printing, he did.  I ran an initial print head cleaning my computer and then clicking the button indicating that the print heads were NOT clean.  He then ran a deep cleansing process.  Then I lined up the printheads of the same print utility program.  Now it works!

• HP Photosmart 6510 e - all-in on: print a picture

  I want to print on paper photo of android (Samsung Galaxy S6 edge).

  The printer is set to ask what tray. Nevertheless, it prints only on plain A4 of android.

  I used the build-in print function the and place paper 4 x 6 inches, the papertray photo value and finally used the application e-print and paper Photo Paper Type value!

  Any help would be appreciated!

  As I mentioned in the op, I tried the HP e-print application.

  But I found a solution, instead of choosing the Photosmart HP 6510 directly (with ip address), I chose Photosmart 6510 with l'[email protected].

  Apparently printing via hp service it does not accept the chosen paper size (4 x 6).

  It works:

  

  But it does not work:

  

  Any other suggestions?

• How can I create custom with the Photosmart 6510 printers paper sizes

  I want to use paper sizes personalized with Word or Photoshop.

  I have a Photosmart 6510 printer all-in-one.

  While I can find the custom size tab layout in Word and can set this size, I don't seem to be able give the new size a name or save it.

  Is it possible with this printer, or is there a workaround to avoid the message 'paper mismatch '.

  Thanks for the ay help I can get.

  I'm sorry not to come back earlier.  I stumbled across a work around for this problem.  Use a different print driver for the printer.  I'll link the instructions below.  Again, sorry I don't come back with the workaround as soon as possible.

  How to assign other drivers to print in different Versions of Windows

• Photosmart 6510: photosmart 6510 prints blank pages

  Printer was working fine.  Had to change the cartridge. First of all, I didn't have black and now I don't have much color either.  The printer says I had no real HP though now it shows that I do. I never bought my cartridges anywhere but the staples.  Printing October 2012 have changed many cartridges before you buy.  Followed everything I could find.  Still not printing.

  Hi @mjohns390,

  I read your post and see that you can not print in black or color now. I would like to help you today. If this helps you to find a solution, please click on the button "" accept as Solution"" down below this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Please, try the following steps to see if it will help solve the problem.

  Printer cannot print black ink or color ink or prints blank Pages.

  This document is for the cleaning of the cartridge and the contacts, check the tab on the cartridge and the printer reset. "Incompatible cartridge" or "indicated ink cartridge needs to be replaced" message on the c...

  If the problem persists, perform a power reset. A alphanumeric Code (example: ' 0 x 'r' C2...) ") displays on the front panel when printing. Do not take into account the title.

  This model has a permanent print head, this video shows you how to access the print head, so you can manually clean the printer and soak the printhead, it's my own personal recommendation, not one of HPs, is to use the solution proposed in the following videos.  I suggest only doing this if the printer is out of warranty.

  Once you get to the clock at 3:20 minutes, you can stop this video.

  Разборка HP Photosmart 6510 (disassembly Photosmart HP 6510)...

  This video is for a different model but it will provide the steps to move the print head and cleaning, also if you continue the video it will provide measures to remove the print head and soaking. Play video 01:24 minutes. HP 5510 will not print black and color - print head removed and cleaned.

  If you have completed all the above steps and your product still has a problem, service the product.

  I hope this helps. Let me know how make you out. Thank you.

• Cannot scan to the computer. Photosmart 6510

  I have just purchase a photosmart 6510 and I cannot scan to the computer.  The printer tells me that I need to activate this via the printer software.  I know that I have installed all the software from the disc supplied.

  I can't find where I have activate the scan of the computer on my laptop.  Support information tells me to click the icon for the printer to my desktop, I do not have!  I tried going through the control panel and impossible to find something there.

  I go in the HP folder in my Start menu and click on scan HP that I get the following message "the machine HP photosmart 6510 series is not found".  I don't have a problem with printing at all.

  Tried to start printing and scanning of doctor and who did not make a difference. (In fact, the scan option came not on it).

  How can I fix this please?  I'm running Windows Vista Home premium.

  Hello.  Thanks for your reply.

  I've sorted really the problem now.  But let me explain what it was.

  I tried tool doctor who recommended you after browsing these forums, without success.  In fact, when I ran the scanner, he told me that he had no problem with printing, but there was no mention of the scanning anywhere.

  In fact, I uninstalled all HP software, removed the printer from my control panel.  Then reinstalled the software from the disc and then installed the printer again (I did things the opposite of the front walkway).  And the scanner function now works.

• Photosmart 6510 - no computer"found" - "Scan to computer" not activated

  Hello

  With the help of HP Probook, with Windows 7 Professional.  64 bit.

  My Photosmart 6510, I cannot scan documents on my laptop. I think that this only started happening recently when I started to use AVG PC Tuneup software, but I have district check if this may be the cause that the scanner is aunable to detect the computer.  I get the following message:

  "No computer was found - make sure that the printer software is installed on your computer and that the 'Scan to Computetr' is enabled via the printer software.

  I uninstalled the software and reinstalled again.  When reinstall it wonder "Enable scan" I agree.

  Previously, the "Enable scan" message popped up whenever I have rebooted, but that has stopped so I think something may have changed.

  Any suggetsions would be welcome.

  TX, Kurt297

  Hello

  Please, download the following tool and run it on your computer:

  http://ftp.HP.com/pub/softlib/software12/COL50849/MP-135113-1/HPPSdr.exe

  Hope he will give some answers if not reinstall full feature software and drivers from following link:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&LC=en&product=5058336

  Kind regards.

• Photosmart 6510: lines horizontal and top and bottom of page when scanning

  Hello

  Scans of the bucket of my Photosmart HP 6510 leave a horizontal line at the top and bottom of the page.

  I tried to adjust every page that I scan to align as straight as possible on the glass and this sometimes helps a bit.

  I am able to bypass the lines in culture to, but would prefer to find a real solution.

  Any help would be appreciated because I don't know a lot about the scanners, thanks!

  I've included a sample page below (the mark on the right side is not dirty glass, it has been a staple in the page):

  

  Welcome to the HP community @lgilb01,

  I wanted to tender hand to respond to your message on the lines that you notice when you scan to scan in your Photosmart 6510 bed. It seems to me that there could be some light enter when performing the analysis, causing lines. If you are only scanning one page at a time, the lines should not appear as they are now.

  Here is a troubleshooting guide for you to try. If the lines do not fade, contact HP directly to see about a replacement printer.

  HP Photosmart 5510, 6510 and 7510 e - all-in - One Printer Series - vertical stripes, lines or scratches in Copies or scans

  Tip: Make sure that the printer is plugged directly into the wall, avoiding bars power and surge protectors. This ensures that the printer is full on.

  Testify of my answer by pressing the thumb in the air below and hit the "accept as Solution" button, if I have you helped a resolution!

  I hope I helped!

  Contact HP:

  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number are displayed.

• Photosmart HP 6510: Personalized printing HP Photosmart 6510 problem

  I have read through a couple of threads and followed the instructions to turn on 'custom' on my HP Photosmart 6510 all-in-one printing. I loaded the driver of HP Deskjet 450, which finally allows me to select a custom size of 5.5 "x 8.25". I'm trying to print on wedding invitations response cards. Wedding invitations made the same paper 5 X and can be printed without adding a new printer driver for the 6510.

  Now that I can get the printer driver (deskjet 450) to recognize the custom format 5.5 "x 8.25" but I can't print. I use a model of design by Staples and get the following errors.

  Errors - the margins of Section 1 are set beyond the printable area of the page. Do you want to continue? I pushed Yes and the printer tries to print the job abd I get the error "paper mismatch". The printer actually determined the size of the paper when I adjusted the paper tray to accommodate custom size paper.

  Troubleshooting - I tried to adjust the margins, but I have little ability to adjust in the template provided. When I adjusted the margins, I always get the error "paper mismatch".

  Any ideas on how to do more troubleshooting?

  Hello

  Please retry the procedure which should solve the problem below.

  (if the printer is connected with USB)

  Click START > device and printer > add a printer > add a local printer >

  Select "Use existing Port" then Virtual USB from the drop-down menu, click on NEXT, in the production list, select HP / Hewlett-packard and in the right pane, select Deskjet 6980 and finish the wizard

  OR

  (if the printer is networked)

  Click START > device and printer > add a printer > add a local printer > choose "Create a new Port" > type in the printer IP address click NEXT, in the manufacture of the list, select HP / Hewlett-packard and in the right pane, select Deskjet 6980 and finish the wizard

• How can I scan with OCR with my hp Photosmart 6510? I want to scan to a text of the parameter file.

  I got a new Photosmart 6510 all-in-one printer. I have the ability to scan to a .jpg file ot a .tiff or a .pdf file - just like the pictures, no form of text that can be edited. On my old photosmart printer (a 2572) I was able to analyze OCR allows you to place the scanned document in a file with the Edition of the text, how can I do that with this new printer? I thought I was adding features, do not remove them. I use the 6510 wireless on a home network. I am also on the Windows Vista system.

  Thank you

  Hi nawa4,

  Software OCR Iris didn't come included with this printer. If you have OCR software installed on your computer, you should be able to scan using this program. If you do not have an OCR program installed you can check the link below.

  http://www.IRISLink.com/C2-2093-189/IRISCompressor---create-and-compress-PDF-files-in-a-click-.aspx?adwp=SAS-IComp-us

• Photosmart 6510 I want to scan multiple photos and then separate them into albums

  Photosmart 6510, I can scan several photos, then create albums in the files I have scanned in IPhoto. ? I tried it but not able to download individual photos off the coast of the photo I scanned.

  Your welcome Oldpro, please be sure to come back and let us know if this has been fruitful for you. It makes it easier for members of the community who may experience the same issues find a resolution.

  Thanks Al!

• HP Photosmart 6510 alignment Page failure, black ink cartridge not working not

  I'm on Mac OSX using the Photosmart 6510 AIO printer 10.7.4. I had problems before printing (black ink would not introduce yourself, sensor said that there was still a lot) so I ordered new cartridges. I printed a report of quality and the color came out great but black came out uneven. Then I used the align parameter and it printed once more uneven black ink and the screen on the printer read "the alignment page failed. It's frustrating, because the printer was used only at the end of last semester and he has not worked since I set up for this semester. Any help would be greatly appreciated, thank you!

  Ryan

  The steps in this troubleshooting page can help solve the problem.  If it is printing black but spotted I expecially make sure I check the vents and run a cleaning cycle.  If the above does not resolve the issue, see the post here.

• Printer HP Photosmart 6510 sends only encrypted or corrupted my computer .pdf files.

  My PDF editing software cannot read any file produced by scan on my HP Photosmart printer.  Whenever the software displays the following message:
  "Cannot open PDF file for editing, because it is encrypted or corrupted."
  My printer is HP Photosmart 6510 e-All-in-One B211a; Product number: CQ761A #B1H.
  My software is WordPerfect X 5, and it opened to all other documents .pdf - so normal text or tables - I tried on my computer.  All have been opened in a format that can be edited.
  My computer is a HP Pavilion dm4-3050us laptop new, operating in Windows 7 Home Premium.

  Hi mt88,

  If you are looking for editable text scans, you can buy OCR software that will allow you to scan to the editable document.

• Photosmart 6510: PS 6510 won't print black

  Printer cannot print black ink. I ran the cycle of cleaning several times. The cartridge is new. Gets moderate use with periods where it is not used. The printer is out of warranty. Mention was made in another series of posts on this problem that there may be more specific than just running instructions once again the cleaning cycle.

  Try here.

  http://support.HP.com/us-en/product/HP-Photosmart-6510-e-all-in-one-printer-series---B2/5058334/model/5058335/document/c03760633/

  Let us know.