DV6 Finger Print Reader unrecognized or does work not

After restoring my laptop (Pavilion dv6-6121tx) a few days ago, I decided to get the most recent drivers.
I stopped to do, I upgraded HP Simple upgrade to version 6.0 (this version was not listed in the drivers for my laptop, I found it on the AuthenTec Web site).
Surprisingly, he did not detect my fingerprint reader.
so I decided to uninstall it and install the 5.3 version (this version is listed in the drivers for my laptop on the HP website)

and even once it does not recognize my device.
so I uninstall this version and went back to the old version 4.3 and still the problem was not solved.
Finally, I uninstalled HP Simple Pass and validity sensor driver. and reinstalled using the typical recovery manager "reinstall drivers and applications.
It still does not work!

Whenever I uninstalled it a version, I deleted my identity with him.
and my fingerprint reader does not even appear in the Device Manager. However, it is an unknown device listed, but I'm not sure if its my finger print reader.

Ask for any other information you need...
even ready for assistance remotely.
any help would be greatly appreciated...

Yay for me...
Finally, it solved my self...
Remove data from print finger, uninstalled the driver both col simple, rebooted my computer laptop and then installed the driver... reboot again, installed Simple pass... and viola! its been...
BTW use validity sensors version 4.3.304 and HP Simple Pass 6.0.100.252

they are much more better that my old drivers... and do not appear in the list of drivers for my laptop on HP.com!

Tags: Notebooks

Similar Questions

  • Finger print reader does not work after upgrade to Windows 8 Pro - DM4 2055BR

    I updated my previous Windows 7 to Windows 8 Pro Edition and the Finger Print Reader no longer works. Validity software driver is already installed more simple pass, but when I run the Easy Pass it pops up the message "the drive is not connected, connect the drive.

    I noticed one lot of other posts related to the same issue, but I don't know if the model of my laptop does not support the new version of the operating system.

    I appreciate if someone could help me with this problem.

    Dulao35,

    Welcome to the HP Forum!

    When start you / see: Easy going on?

    You may be running HP SimplePass Version 8.0.0.57 or some other SimplePass 8.x?

    ======================================================================================

    You can run HP SimplePass Version 6.x later on your computer.  You may also be able to get SimplePass version 8.x if you want to stay with this version to work.  It's a personal choice, really - either version should be able to work on Windows 8 Pro.

    Note that the version 8.x SimplePass seems to dislike everyone, but the Internet Explorer browser. This is a personal observation and NOT what can known by other users.  If you use IE, then the point is moot.

    You can probably keep your existing driver of the fingerprint (Validity Sensor in the Device Manager) as long you run the version compatible with Windows 8, illustrated to the webpage of your computer driver:

    HP Pavilion dm4-2055br Entertainment Notebook PC Drivers

    See below for a method that you can use to upgrade HP SimplePass:

    Simple Instructions for upgrade HP SimplePass

    The bits on SimplePass version 8.x are towards the bottom of the file.

    Click on the star of congratulations !

    It's a nice way of saying 'Thank you' for help.

    Although I strive to reflect best practices of HP, I do not work for HP.

  • Finger print reader does not connect for Win7 Logon Screen

    Win7 Ultimate 64 bit

    5.9.4 fingerprint software

    Biometric accepted link to windows Logon

    Client Domain Server MS

    At the start of the system, the logon screen appears and the fingerprints light is 'on '. I scan my finger, the light blinks once and no presentation of the Windows password in the logon window. I have to enter password.

    Lenovo support asked me to uninstall software, of the clear BIOS saved digital fingerprints then re - install (and re-record). I did it twice without any change.

    It worked until I had to break the connection of field (server change) and re log on to the domain with the same opening of session and password. It was at this time that the finger print reader stopped passing the biometric password to the BONE.

    Any thoughts on how to re - connect the reader to open a session?

    If you enter the control panel and search for "biometric" you should have an option to 'change the biometric parameters '. If you click this option, you should have a checkbox indicating "Allow users to log on to a domain by using their fingerprints", make sure that having checked if you want to connect with a domain account using your fingerprint. When remove you / add the computer to a domain, so I believe that this option will be restored back to being disabled must be re-activated.

    -gan

  • Finger Print Reader no longer works after update from Microsoft on the HDX laptop

    The stop Finger Print reader work shortly after Microsoft Update, HDX Premium, Vista 64 bit, after a regular update of Microsoft Fingerprint Reader became sporadic. I have been instructed by HP to download the software from the HP (Digital Persona Fingerprint Reader Software) website. It gives me an "error message 1321. The installer of the sufficient privileges to modify the file C:\Windows\system32\DpPwdFlt.dll.' after failing to install it and then restored install it and then it after that I can't use my Finger Print Reader to log even when booting

    Hello

    Try right click on the installer of Digital Persona, and select 'run as administrator' to see if this will allow to complete the installation

    Concerning

    DP-

  • Vista drivers for finger print Reader on a Portégé R200?

    Help, please
    I have a R200 model originally shipped with Windows XP, now have Windows Vista Business Edition installed & have problems to make Finger Print reader to work. I tried many programs Windows is said to have installed properly, but they all State that the player is not connected?
    I tried so many times to let him work and looked at the site factory drivers or software, but nothing.
    Seems very strange for a laptop Toshiba, not not working completely, even when it says on the sticker of the OS Windows Vista Capable?

    UM

    Hello

    where to download the drivers? Maybe on the European Web page? Here are some links with toshiba driver download pages where you can probably find some drivers you need:

    http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
    Toshiba - download

    http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_sc_home.jsp
    ToshibaUSA

    http://209.167.114.38/support/download/ln_byModel.asp
    Toshiba of Canada limited - drivers and downloads

    Welcome them

  • HP Pavilion dv9700t Finger Print Reader

    Sorry, I'm new to this, so I don't really know what I should add can help people. in any case, I have the HP Pavilion dv9700t laptop and about 6 months ago my Finger Print Reader stopped working all together and said it is not detected when I try to use it to connect. I tried to download the drivers again, but he did nothing.  I am running Windows Vista and update as soon as I can. Anyone know if this could be a problem?  I'm not hard with my laptop, so I don't think that it is because something fell out of place, but I don't know, because I don't know how to open upwards and don't want. I had the extended the warranty, so I just need to send it in, but I use my computer every day and don't really want to part with it as long. Thanks for any help.

    Check Device Manager, check the personal identification device driver, see if the driver works correctly.

    If it was a software problem, uninstall the current driver and try one of your support page.

  • Need driver for Windows 7 device and software Instalation for Microsoft Keyboard with Finger Print Reader

    Hello, I bought a MS Keyboard with Finger Print Reader (product ID: 75913-545-1980296-00611) recently of a *. May Hae product on a shelf for some time. I have Windows 7 on my PC and the instalation software says it's incompatible. Have you folks instalation software compatible for your product? E-mail address is removed from the privacy * I am a technician certified a +. If you could direct me to the right site with the appropriate software, or email it to me, I would appreciate it. Thanks for any help you can give. Sincerely, Frank Nunally

    Hello, I bought a MS Keyboard with Finger Print Reader (product ID: 75913-545-1980296-00611) recently of a *. May Hae product on a shelf for some time. I have Windows 7 on my PC and the instalation software says it's incompatible. Have you folks instalation software compatible for your product? E-mail address is removed from the privacy * I am a technician certified a +. If you could direct me to the right site with the appropriate software, or email it to me, I would appreciate it. Thanks for any help you can give. Sincerely, Frank Nunally

    This is a forum for peer-to-peer and this product is not compatible with Windows 7 - so - don't.  Microsoft is not what you need.  Should have read the list of compatibility (operating systems) probably printed on the box.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Windows-7-Ms-keyboard-with-fingerprint-reader/43918b4b-7368-4569-aa13-b7337192f3f4

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Microsoft-keyboard-with-fingerprint-reader/5e9fcad4-20e1-4440-a4ae-47b1fb47798c

    But be sure to check here:
    http://www.Microsoft.com/hardware/en-us/support

  • Portege R700 Finger Print Reader suddenly not recognized OS

    Hello

    I've been looking for a solution

    My R700 on Win7 worked perfectly using the finger print scanner. At any given time without cause the
    hardware (fingerprint reader to log on) was not recognized by the operating system more.

    -J' tried to remove the software, reinstalled driver
    -updated it and so on resulting material was not found.
    -J' even deleted all the entries in the register - no go.

    -Finger Print genuine software starts, but only to give an error that the FP-reader is not present.

    Is there a way to remove the fingerprint stored manually by removing the manually.

    The equipment works according to the support. (The machine has been send)
    However I don't want to re-setup of the entire machine (it is a work laptop) just to make it work?

    Intro step by step to achieve this or advice?

    I couldn't find a description on how to manually remove fingerprints (cause I suspect this is the problem) from the software to do this does not start.

    Any input would be appreciated.

    Best regards
    Julian

    If you do not see material unresolved fingerprints or devices in Device Manager, then the device is either disabled in the BIOS or the fingerprint sensor is defective or too loose or there is a spill of liquid causing corrosion.

  • Satellite A100-756 has finger print reader and remote control?

    My notebook there finger print id? The manual says it's but I can't and also it is supposed to be a remote with it but I've not seen a.

    Does anyone have any ideas?

    I'm sure that the textbooks said that these options are available on some models. If your laptop was original packed in and you have not found remote in the box of the situation is clearer: remote is not available for your model.

    In any case, I found info on the remote control to A100-756 and there is advice: remote controller not available.

  • HP ENVY 17-j005tx Notebook Finger print reader questions

    Hi all

    Already a few weeks or so, my fingerprint reading begins to play up - when I start the laptop, it seems do us somehing to the connection and logon fails permanently - when I try to open a session keyboard always fingerprint reader sends something and can not connect - it just cause connection to fail over and over in a loop.  I can just manage to turn off the laptop by clicking on the button turn off and select the off option.

    I found a reason if I hit F10 to enter the BIOS setup, e and exit, reboot all goes well.  Then I can use the fingerprint reader to log in again. Then a few weeks can go and the same thing!

    What gives?  Someone at - it suggestions? Is this a bug of material or something - it is possible to disable the fingerprint reader so that if in the future he sticks completely upward, I would at least have the ability to disable.

    Jim

    8.1 Windows x 64

    Validity Sensors, Inc. - 4.5.122.0 - 19/03/2013

    HP Simplepass 6.0.100.276

    Laptop HP ENVY 17-j005tx, HP ENVY 27 - k001a, HP ProLiant MicroServer Gen8 G2020T, HP MediaSmart EX495 Server tilt, HP MediaVault 2020, HP ENVY 120 AiO Printer

    Hey JimT.

    For the fingerprint reader not working not properly, I've included the document ' a (Windows 8) fingerprint reader troubleshooting'.» Please follow the steps in order for best results.

    So, there is a fingerprint sensor driver update digital validity. I got it here for you. This pilot has a version of the 4.5.228.0 Version and was released on 09-30-2013.

    Please let me know if these steps solved the problem, thanks.

  • Some keys on the keyboard does work not after the suspect virus on Tecra

    Apostrophe, delete, semicolon and the end of the keys no longer work after a suspected virus attack. I found the same problem on the net record but apparently this guy fixes his problem after stop scroll or NumLock on found him.

    This isn't the case here, but it's something with numlock - registry Watch 2 and not 0. switch to 0 but when reboot 2 times.
    Suspect has changed through the bios. I thought that I couldn't get to the bios because DEL key does not but found ESC works.
    Tried to reset the values default to the bios but then can't save and exit it in accordance with the EndKey to work.

    I was running XP at the time of the (alleged) attack and could not correct the problem so to put the computer OEM as I hoped would help - there no, same problem, so instead of installing all the software on the computer with XP I upgraded to Windows7 - charge install.

    Keys still don't work - it was a real pain first as my computer was created for ctl + alt + delete to log on and I had to do with the keyboard of the screen - XP - it showed also that numlock performed before and after windows starts.

    The reason why I suspect a virus - my wife was watching an of its tv shows on the line of the country of origin (an another toshiba laptop) and I needed to use this laptop for something else, so I asked to use mine - then we turned off laptops and the morning turned tham back on again once , the other laptop with virus protection AVG reported several hits and this one with Norton (FAMOUS and completely up-to-date) flagged nothing - once I got the screen keyboard.

    Problems with this computer were found after scanning with different antivirus.
    Anyway - I find myself with 4 keys that don't work not on my keyboard (in fact they work after I have connected to the computer for the first time, but I had to hold them in place for a long time - and then the next time I rebooted, not at all and did not since)

    Here, any help would be greatly appreciated, I'm working on this all weekend with no joy at all.

    Thanks in advance.

    Having a virus attack, the Windows files will be destroyed. Try the scan with kaspersky on Nod 32. If not help, reinstall os because it is the best solution in your case.

  • Envy 17 - T n100: Finger Print Reader does not work

    I have a new machine.  The fingerprint reader does not work, no light, no response.  I uninstalled the device in device manager, rebooted and reinstalled, still no response.

    Has sought to pass Simple software but could not find it.

    Where should I go from here?

    Hey!

    Did you uninstall the driver of the fingerprint in before Device Manager?

    To use the download I you provided, you will need to uninstall the driver again.

    • Open the Device Manager
    • Search for biometric devices
    • Under biometric devices, look for the device (called Validity Sensor sensor AuthenTec)
    • Right-click on the fingerprint sensor
    • Click on uninstall
    • Restart your computer.

    Here's a download for the fingerprint reader. This download sp71729.exe might work for you.

    As a last resort, you can try:

    Thank you for being a part of the community of HP. Please let me know if that helps solve the problem by marking this message as "accept as a Solution. If you need more assistance let me know and I will gladly do all that I can to help. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

    Thank you!

  • ENVY dv7-7201sa Finger Print Reader does not work

    The fingerprint reader has stopped working. Before, I thought I had genuine driver installed, now there is driver driver. Not sure how it happened.

    I uninstalled the driver drivers and pass SImple, but the single pass software download link is no longer available, what are the correct drivers, and where are they

    Thank you

    Tony,

    If you tell the AuthenTec link for the 6.0.100.620 old version of HP SimplePass, it is probably closed.  AuthenTec has been picked up by Apple last year, and they are «not more»  The drivers are still in the area - the name depends on the original software / driver source code.

    For Windows 8:

    Your valid driver - download and install not yet:

    sp58900 validity sensor V4.4.234.0 Win8

    Reference: ENVY HP dv7-7201sa Notebook PC drivers

    Instructions for installing the driver and HP SimplePass later that works on Windows 7 or Windows 8 are in the following file.

    Find, open, and follow the procedure described in the file named: simple instructions for upgrade HP SimplePass

  • The sensor validity finger print reader and windows 7

    I recently installed windows 7 Enterprise 64-bit on my dv4t-1300cto. Everything is great except for the fingerprint reader is not working. It appears in the device as manager being installed correctly, but windows and digital persona say its not connected. I tried a few reinstall software and drivers, but nothing helped. And when I look for software, the results are quite rare. HP tries to convince me that I'm using a beta version software and support will appear soon, but is not a copy of version beta what whatsoever. Everybody do what ive made and it sorted?

    the drive model is Vfs201.

    Thank you all.

    @engrarielmr

    Hello

    Check the linke below:

    HP SimplePass Identity Protection, validity of fingerprints fingerprints and Windows 7.

  • X23O Finger Print Reader LED lights up when the unit is off NORMAL function?

    Hey guys, is it normal that the fingerprint reader to Flash green when the X 230 is off? Win8 running

    Thank you!!

    Thank you very much for your help! I thought about it all now! You guys rock! You can turn on the lights and turned off, you can turn this feature on and off as well! Thank you! Its ALL in the settings of the Lenovo for the FR software that I have installed! Thank you!

Maybe you are looking for

  • Running a 3rd monitor Radeon 5870

    Afternoon, I am running 2 cinema Display 30 ' on my PowerMac. I upgraded to a Radeon 5870 as it can run 3 monitors... I bought another monitor, plugged into the HDMI connector & 2 only one race at a time? I read online that you need an active HDMI ca

  • R8500 Firmware MU-MIMO

    The recent firmware has no option to activate MU-MIMO. This option is only with the firmware.28 and the beta version I have. I am told that the latest firmware has indeed HELPED MU-MIMO. Is this true? or did the version having the box turn on in adva

  • How to clean the files of time machine restore after reinstall

    Just did a wipe and reinstall on an iMac 2011 (10.8.5) mountain running Lion. I don't want to do a full restore from Time Machine; I just want to take a few important files (cache profiles, e-mail, etc.). [Did the reinstall because my system was flaw

  • Upgrade CPU on Satellite A40

    Hello I m wondering if anyone knows what the best processor I can put in my Satellite A40, as the current is on its way and so I m wondering if I can put in a Pentium M because I think he has the same socket. Thanks in advance

  • Library of Multisim of AD5700 Modem HART for the simulation file

    Hello Can anyone give any assistance with simulation on Multisim with PIC 16F877A with HART communication on industry standard 4. 20 Ma loops... I'm trying to simulate Modem HART AD5700 on Multisim with PIC16F877A. I want to send serial data to AD570