DVD / CD ROM Drive - cannot load the drivers

My DVD / CD ROM has stoppped working.  Replaced by a new, but get this error in Device Manager

Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

New CD-ROM/CD-RW, or DVD-ROM, etc., usually never come from the factory with

the parameters of the right stem. Take the device, look at the back, place the jumper pin plastic.

set to slave or master, if possible, install it on another cable IDE, set another pin device

According to the needs. XP will reinstall at startup.

In addition, most of these devices is "firmware" updates, go to his web site from mfg & install it

If it is available...

Tags: Windows

Similar Questions

  • This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

    Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

    This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

    Jake

    Hey Jake,

    Follow these methods.

    Method 1: Follow these steps:

    (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

    (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

    (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

    Remove or reconfigure newly installed unit.

    Restore a version prior to updating the driver.

    Use system restore to undo the Device Manager recent related changes.

    http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

    (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

    Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

    Method 2: Update the latest graphic drivers.

    Updated a hardware driver that is not working properly

    http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  • I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

    My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

    Is anyone know how can I access my hard drive again?

    Thank you

    Hello

    You has made changes to the system before the error appearing?  Cancel the changes.

    (1) in Device Manager > right click on the driver, and then select uninstall

    Reboot and Windows will reload the driver

    (2) remove the upper & lower filters that cause errors in Code 31

    http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

    Access the manufacturer's Web site and search for updated driver

  • Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

    Original title - USB - IF xHCI USB Host Controller

    This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

    I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

    Hello

    USB devices remove all you can - restart the computer - is still there, the error? If it isn't
    It is related to one of the add-in devices that you removed. If she is still there, then, the question is
    either a device internal who can not remove or physically with the USB bus itself.
    If it was not there, add devices at a time until it is displayed - keep in mind that it is
    possible that there are two (or more) devices in conflict over the issue. Once you
    identified the check of the aircraft with the help of the manufacturer.

    1. to find the control panel - device - device - right-click on it - uninstall - Manager then
    Restart the computer to see if it clears.

    2. same place - double click on the device - driver tab - driver update - to see if that helps.

    3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
    online documentation and drivers, diagnostics and ask questions in their forums on all known
    questions. Update the Bios and chipset or other USB drivers.

    =====================================

    If necessary, we will use these additional troubleshooting methods:

    How to fix Code 31 errors
    http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • My crashing after windows loading and I have this message - this device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

    This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

    Hello

    Have you tried to update the drivers as suggested by Basith M?

    Method 1:
    You can run the fix provided in the link and check out them.
    Hardware devices do not work or are not detected in Windows
    http://support.Microsoft.com/GP/hardware_device_problems


    Method 2:
    You can also try the procedure described in the link to troubleshoot driver issues.
    Tips for solving common driver problems
    http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems

    See also the proposal contained in the link and check.
    On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
    http://support.Microsoft.com/kb/932520/en-us
  • Norton 360 diagnosis reported: Microsoft ISATAP Adapter #2 is malfunctioning and windows cannot load the drivers required - code 31.

    Original title: ISATAP adapt #2 does not properly. How can I solve this problem?

    My Norton 360 diagnostic report detected a hardware device unusable.  The device type is: Microsoft ISATAP Adapter #2 and the device situation mentions that it is working properly and windows cannot load the drivers required - code 31.

    I think that it is also affecting my internet connection and disrupt its speed.

    Can you please help with this question?

    Thank you very much
    Tony

    Hi Tony,.

    You can try reinstalling the device driver and check if it works.
    Uninstall and reinstall the device in Device Manager.
    a. Click Start, type devmgmt.msc and press to enter.
    b. Locate the Microsoft ISATAP Adapter device
    c. right-click on the device and select uninstall
    d. restart the computer and check.

    You can also consult the following article:

    On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
    http://support.Microsoft.com/default.aspx/KB/932520

    Hope this information is useful.

  • Windows cannot load the drivers for the network device, Code 31

    A few days ago, my computer was working very slow... I turned off twice and he turned his back.  The letters on the screen were enormous when windows restarts.  I turned off and did a diagnostic system before windows starts and everything was fine.  The computer is restarted my network cards were missing.  I get the error: this device does not work properly because Windows cannot load the drivers for this device. (CODE 31).  (Module Aetheros 802.11 a/b/g/n dualband wireless network and Realtek PCIe GBE Family Controller).

    I have downloaded device drivers (windows could not find them on my system) using a laptop and copied computer on a disc.  I tried to install and I got an error message indicating that windows has failed.  I did a system restore to a point a few days before I started having problems.  Windows cannot successfully go back to the restore point.  I spoke with a technology computer and HP tech.  HP technology seems to think that windows is damaged and I need to remove and reinstall it on my computer.  I spoke with computer technology in my area, and he seems to think that my hard drive has failed, however I can still run photoshop and backup my system.

    Does anyone have any ideas before I m computer local tech.  3 year warranty just expired February 1, 2011.  Don't you know.

    Hi TeresaPacy,

    1. don't try to install new software or hardware on your computer recently?

    You try to run a SFC scan to check the corrupted system files.

    You can read the following article to launch the SFC scan:

    How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

    http://support.Microsoft.com/kb/929833

    Regarding errors of network adapter, you can consult this article:

    http://TechNet.Microsoft.com/en-us/library/cc725584 (WS.10) .aspx

  • Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

    System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

    Thanx

    Hi rui2010,
     
    Place your machine in a clean boot State to see if another application is in conflict with the modem.
    If this fails, I recommend you reach out to the community Hauwei for assistance:

     
    Aziz Nadeem - Microsoft Support

    [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

  • Get the error code 31 this device is not working properly because Windows cannot load the drivers required for this device.

    Original title: WAN miniport driver

    A yellow sign appears on MINIPORT Wan (IP), MINIPORT (IPV6) AND WAN WAN MINIPORT (NETWORK MONITOR) for this reason I have not access to internet to throw bluetooth tethering that even he does not connect. In the properties of the driver, it indicates:-this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

    I use windows 8 in my sony vaio
    MODEL - SVE15123CNW

    Hi Praveen,

    Perform the steps suggested by Nirmal S from the link below and see if it helps.

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/i-get-an-error-code-31-in-Device-Manager/3364d05a-af20-4f6d-8597-b4b9f6a74b60

    Answer please if you have any questions.

  • Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

    Hello!

    I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

    "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

    Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

    When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

    Thank you!

    Hello

    You must get the drivers latset for m computer support site.

    Delete the "false: entry in Device Manager and install the new drivers."

    Jack-MVP Windows Networking. WWW.EZLAN.NET

  • (Code 31) "" device is the ' WPD file system Volume driver "-Windows cannot load the drivers"

    original title: in (under portable devices) Device Manager I get the following message. _ "the device is not working properly because Windows could not load the drivers required for this device. (Code 31) "" responding device is the "WPD file system Volume driver" _

    The Windows Event Viewer reports-

    Information - drivers have been installed successfully for device - driver Installation
    Information - it was not possible to access the device () after installing the drivers.
    Error code 0 x 80070651 - migration pilot

    I finally solved the above as follows;

    a reinstall the drivers of my motherboard chipset

    b, restart the PC

    c will unistalling and then remote control panel/system/Device Manager device possible (it is not possible to remove all)

    d PC restart and all devices removed in step C reinstall themselves automatically - restart the PC once the process is complete and the problem is solved

    PS the problem the appliance was a USB2 memory card reader

    Hope this works for you

  • D/DVD-ROM drive cannot read the CD or DVD

    Hello

    I use Windows Vista on my laptop. Its quite some time that I did not use my DVD/CD drive. Today, I try to use but cannot read any CD or DVD. I was trying to solve the problem of updating the drive, but still cannot fix. Can I use Microsoft FIX IT microsoft support but the problem still there.

    Something to say: windows cannot start this hardware device because its configuration (in the registry) information is incomplete or damage (Code 19).

    Click on 'Search the soluton' to send data about this device to Microsoft and to see if there is a solution available.
    I did it but the result is COULD NOT LOAD DRIVER SOFTWARE.

    Please advise what should I do?

    Thank you!

    Hello

    It is very rare for the methods in the 1st answer above does not fix a Code 19.

    You might have a disk problem as the CD/DVD is actually 4 discs in 1 case (CD & DVD and CD burn and)
    DVD playback). Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry entries
    that the troubleshooter does not, and those who "could" be the cause.

    Check with your system manufacturer Maker and device for possible firmware updates and the good
    Your player registry entries.

    Here are the keys in my opinion, are those in question - for the reader of CD/DVD subkeys of course that he will be
    other subkeys in these keys. Be sure to ask specific keys involved as well as the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD-ROM drive settings of
    someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • Microsft #8 ISATAP adapter... This device does not work because windows cannot load the drivers for this device Code 31... ??? Can anyone help I just use computers don't understand them...

    I tried to update the drivers but it says that I have installed the last...

    See this:
     
    On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
     http://support.Microsoft.com/kb/932520
     
    You can ignore this error message. This error message does not indicate a problem with the adapter. The adapter will continue to function correctly.
     
    You can uninstall and windows should reinstall on reboot, but you can install it yourself.
    How uninstall/reinstall Isatap
     http://www.ehow.com/how_7567513_reinstall-ISATAP.html
     
    If you cannot connect to your network, you have another problem.
    Try to manually update your (wireless) network adapter. Go to the support site for your computer manufacturer and download the latest driver:
     
    How to upgrade Windows Vista drivers
     http://pcsupport.about.com/od/fixtheproblem/HT/updatedrvvista.htm

  • Cannot load the drivers and software, can not remove current universal drivers drivers HP L7590

    I have officejet pro L7590 - my print drivers are the HP Universal print driver.  I would like to load the software and drivers for the original L7590 because I lost the HP Solution Center.  I downloaded the software and complete drivers for this model and tried to install it, but it tells me that I have updated drivers and it does not reinstall drivers print and software.  When I look at my file to the printer, it does not show my printer.  What can I do to get off the universal drivers and reload the original drivers.  I tried to uninstall the HP Universal drivers, but it does not appear in my programs.  Any help would be appreciated.  I also tried of revo uninstaller to uninstall the universal print drivers, but that has not worked.

    I am running Windows XP

    Thank you

    Karen has.

    Hi Allerk,

    Try using the brush included in the CD or download.

    Of the Original installation CD:

    1. Insert the CD in the drive and then cancel Setup

    2. open my computer and click right then on the CD from the drive and select open

    3 open the Util folder

    4 open the CCC folder

    5. If you have an HP computer, run the L3uninstall.exe. If you have a computer not HP, run the L4uninstall.exe

    6. once the uninstall is complete, restart the computer

    If the software has been downloaded and extracted to your system:

    1. type % temp % in the field of race

    2. Locate and open the folder starting with 7z (example: 7zS2356)

    3 open the Util folder

    4 open the CCC folder

    5. If you have an HP computer, run the L3uninstall.exe. If you have a computer not HP, run the L4uninstall.exe

    6. once the uninstall is complete, restart the computer

  • This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) my video card does not work why?

    can u help me quickly?

    Hello

    -For how long have you had the problem?
    -Did you change your computer, after which the question began?

    I suggest that you uninstall and reinstall the drivers for video card and check if that helps.

    Uninstall or reinstall a device

    Note: Not applicable for Windows Vista also.

Maybe you are looking for