DVD read Drivre onlly CD but not dvd

I did a restore that installed windows vista sp1 on my laptop but the problem is that

now dvd drivr only reads CDs and not DVDs

NET much the said firmware update, I searched but I got HP dv6602au laptop computer I can't find firmware help kindly me

concerning

raj1402

Hello

You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
correctly.

Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
tolerances. They may be delivered, but it is generally more economical to replace the disk.

Several good info here:
http://Club.myce.com/

CD/DVD units
http://www.myce.com/storage/

Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

===========================================

This troubleshooting could not help if there is alignment and/or wear issues however it
a shot.

Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.

Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.

Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.

Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr Fixit

Try this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

Your CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116

The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461

When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052

Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problems

CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/

Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problems

Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.

Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

===============================

Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.

Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.

Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

-----------------------------------------------------------------------

You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.

Forums - a lot of expert real help
http://Club.myce.com/

CD/DVD units
http://www.myce.com/storage/

Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.html

I hope this helps.

Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

Tags: Windows

Similar Questions

  • Reading to the MAX but not of LabVIEW

    Hello

    I have a very difficult problem to read four counters of a NI 9401. In MAX, they read very well but in LabVIEW, they read zero. I scoured the internet and discussion boards and can't find anything on it. Please forgive me if this is a simple thing to fix. IM attaching two png which shows where I read meters and a picture of my task. I know that the VI everything would work better but I'm not posting my project as a whole.  I fixed it where some of the forum posts I found said have it better. Any help would be great. If you need a certain thing just let me know.

    Kind regards

    caleb1993

    I create now these tasks in LV I always not to read. I hope someone has assured this problem in the past and resolved. If yiu have a better idea then by testing each port call please let me know

    Thank you

    caleb1993

  • Reads OCR training character, but not the program labview

    I am training characters, then check my program is able to read the same characters. Every article I read has 8 of the same characters in different parts of the King. Because it is a curved surface, each position is formed independently. 3 the posistions, I formed the character '5' and it will recognize without any problem in the roc training program. Using the exact same ROI, it will not read the characters in my program. All settings, IE the resolution read, read strategy, erosions, etc. are the same in both programs. It notes the character, don't know what it is. I use non-linear threshold. Indicator report of character, I took the threshold values, it uses in my program and is entered as a range threshold fixed on the formation of ocr. This turned the blue character just as expected and read without any problem. Unless there is a setting I'm missing, it seems that the OCR Application does not use the text for reading OCR Idem 3 I use in my program. Any suggestions? I know it's complicated, I'll add the image and a screenshot showing what I mean

    I fixed it! I became crazy and set all the properties of ocr, even those I was using just the default setting. Weird.

  • Adding an image at the signing, but not in the signature field, in Reader

    Hello

    I would like to know if it is possible to add an image to a PDF when I sign the document in the reader.

    I don't want to add the image in the signature field as a signature, but rather under the signature field. The image is ' n barcode provide me with more information about the signature.

    I looked at the example Stamper, but this feature is not avialable in Reader.

    Thank you

    Magda

    PDPageAddAnnot works on compatible reader of PDF files.  Otherwise, Yes, you need Cos.

    From: Adobe Forums [email protected]<>[email protected]>

    Reply-To: "[email protected]<>[email protected]> ' [email protected]<>[email protected]>" "

    Date: Thu, October 27, 2011 00:56:18-0700

    To: Leonard Rosenthol [email protected]<>[email protected]>

    Subject: Adding an image in the reader at the signing, but not in the signature field,

    Re: Adding an image in the reader at the signing, but not in the signature field,

    created by magdakuithttp://forums.adobe.com/people/magdakuit> in Acrobat SDK - see the discussion complete onhttp://forums.adobe.com/message/3992749#3992749

  • Equium L20-264: CD/DVD player can read but not burn discs

    Hi all

    I need help. My laptop cd/dvd driver does not recognize the discs inside. It only happens when I try to burn a disc. She can read but not burn the discs. What could be the solution? I tried different brands, the last time it was Maxell. The manual suggests Mitsubishi discs, but I'm not sure that it only works with the Mitsubishi discs. It can read any kind of disc.

    So I'm in trouble, please help.

    THX
    Gabor

    Hello

    In the manual, you will find a list of media recommended because this media has been tested and were working properly.
    However, I use TDK CDs and DVDs and it works as well.
    Juan suggested in another ad that sometimes 3rd applications or DVD copy locks are responsible for some driver problems:
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=12497

    What I mean is that it is not easy to give a generally the solution of these problems.
    You should try different media, burning software and if it doesn t work so it s is a malfunction of the equipment. In this case, you will need to replace the drive.

  • I have a cd and dvd ROM on my computer but it will not read the discs and is not recognized on my computer

    Original title: no dvd

    I have a cd and dvd ROM on my computer but it will not read the discs and is not recognized on my computer

    Hi Lesliestones,

    ·         Did you do any change on the computer before the show?

    Follow the suggestions below for a possible solution:

    Method 1: I suggest refer you to the article in the Microsoft Knowledge Base and check if it helps.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs

    http://support.Microsoft.com/kb/982116

    Method 2: You can run the fixit and check if it works.

    Your CD or DVD drive cannot read or write media

    http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

    I hope this helps.

  • Reads dvd but not cd

    Here most of the issues have the opposite problem - can read CD but not dvd.  I recently had my computer cleaned using "easy Support. Before that, the computer can read both. Could it be the problem? Any help will be appreciated.

    Ideas:

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem
    Hello
     
    The article below describes how to troubleshoot common problems that may occur when a Windows XP-based computer cannot read a CD or a DVD in a CD or DVD drive. This article contains several methods that you can use to try to solve these problems, and it also includes some advanced troubleshooting steps.

    How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD
    http://support.Microsoft.com/kb/321641/
     
    Aziz Nadeem - Microsoft Support

    [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

  • ATAPI DVD A DH16AYH ATA Device read DVD but not CD

    Engraver of CD/DVD in Compaq Presario 5010NX w / VistaBasic read any DVD but has problems with CD if I insert a music CD, sometimes it will open right and I can play music. Most of the time he just tells me to "insert a disc", usually open the status bar, but not always. If I close the drawer [or eject and close the tray] from 3 to 15 times, he finally opens the CD. Generally. Sometimes I drop and open it on my old computer Millennium, [which never fails to open the CD].  I bought a cleaning disc, but it still happens. Also, it stopped opening the tray with the manual key (1,200 works tent) and will always open with 'Eject' of the computer, but only with DVD and sometimes will open with the "eject" computer with the CD never if it is empty, so I always keep a known disc "opener" in the status bar. (if I forgot, I use a paper clip)

    I did an online search of the Device Manager for a driver update and he told me that the best software is already installed. I just need a new burner? Why is - that it will work with DVD CD not? driving me crazy. Thank you ps can not find a burner mfgr. says simply "drive SuperMulti DVD with Lightscribe" - pps I tried uninstalling the Device Manager, and then restart the computer - no change.  Haven't tried the support.microsoft.com/gp/cd_dvd_drive_problems diagnostic program no solution I came across a post from someone else who had the same problem [former position & 'uninstall & reboot' was the only suggestion on this one.]   I can't believe that it could be physical burner... why he wouldn't hesitate to read the DVD if it was a physical problem?  Help?

    Hello

    Check with Compaq Support, their drivers and documentation online and apply to the
    HP forums for known issues. Compaq can give you more information on the disk.

    Compaq - support, drivers and documentation online
    http://www.Compaq.com/country/cpq_support.html

    Compaq (HP) - Forums
    http://h30434.www3.HP.com/PSG/

    ==================================================================

    Readers to use and this intermittent problem can be caused by wear.

    You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
    Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
    correctly.

    Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

    Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

    CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
    tolerances. They may be delivered, but it is generally more economical to replace the disk.

    Several good info here:
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
    http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

    ===========================================

    This troubleshooting could not help if there is alignment and/or wear issues however it
    a shot.

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Try this fix manually if the Fixit 314060 does not work
    http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

    Your CD or DVD drive is missing or is not recognized by Windows or other programs-
    a Mr Fixit
    http://support.Microsoft.com/kb/982116

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    for Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
    Vista installation after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and
    the correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD/DVD settings
    drive from someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
    nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

    DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
    devices and their properties in flat table, instead of the tree viewer
    http://www.NirSoft.NET/utils/device_manager_view.html

    I hope this helps.

  • writing cd Rw but not rw dvd .plz read the full message

    Hello Sir,

    I bought this laptop used at a local retailer, the hp compaq nc6400 model. Windows 7 installed on it. but the problem is that it writes CD RW but some DVD RW reading and does not not save. I tried to understand as far as I can tell, it's a combo drive because when there is no disc inside the icon on the cd shows DVD/CD RW E: drive, so to the best of my intellect, I understand that it is hopfully a combo drive. I also read the manual, even is written there. so, please guide me that how I can write DVD RW on my system and how I can confirm with certainty that my drive is a combo drive, not just a cd re writable? I read the question already posted to this topic and the answer too, but I don't want to use nero I would write using windows and the said method in windows help that is, dragging the files first. Please answer as soon as possible.

    Thanks a lot for your concern.

    You need to check the capabilities of the car - there are a good number of readers out there that read and write CDs but play only DVDs and impossible to write about them.  Compaq web site should be able to tell or you can get the brand/model number of the drive from Device Manager and do a Google search.
    "Hashimaaq" wrote in the new message: * e-mail address is removed from the privacy... *

    Hello Sir,

    I bought this laptop used at a local retailer, the hp compaq nc6400 model. Windows 7 installed on it. but the problem is that it writes CD RW but some DVD RW reading and does not not save. I tried to understand as far as I can tell, it's a combo drive because when there is no disc inside the icon on the cd shows DVD/CD RW E: drive, so to the best of my intellect, I understand that it is hopfully a combo drive. I also read the manual, even is written there. so, please guide me that how I can write DVD RW on my system and how I can confirm with certainty that my drive is a combo drive, not just a cd re writable? *I read the question already posted to this topic and the answer too, but I don't want to use nero I would write using windows and told method in windows help that is, dragging the files first. * Please answer as soon as possible.

    Thanks a lot for your concern.

  • MY DVD - RW DVR-112D ATA DEVICE IS ONLY PLAYBACK DVD VIDEO (EX MOVIES). BUT NOT READ ANY OTHER TYPE (E.G. SOFTWARE).

    MY DVD - RW DVR-112D ATA DEVICE IS ONLY PLAYBACK DVD VIDEO (EX MOVIES). BUT NOT READ ANY OTHER TYPE (E.G. SOFTWARE). Everytime I put a dvd movie it plays automatically, but any other type of cd it will say insert disk. One has had this problem?

    Hello

    You have disk problem as the CD/DVD is actually 4 discs in 1 case (burn CD & DVD and CD and DVD read).
    Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

    Several good info here:
    http://Club.myce.com/

    Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
    http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

    ----------------------------------------------------------------------

    Step 1: Please make all underneath the same if you've done it before as it's often the total of the process which
    solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
    Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
    This will refresh the default driver stack. Even if the reader does not appear to continue below.

    Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
    slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
    Playback of CD and DVD). Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry entries
    that the troubleshooter does not, and those who "could" be the cause.

    Check with your system manufacturer Maker and device for possible firmware updates and the good
    Your player registry entries.

    Here are the keys in my opinion, are those in question - for the reader of CD/DVD subkeys of course that he will be
    other subkeys in these keys. Be sure to ask specific keys involved as well as the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even registry settings correct for your CD/DVD drive
    a person with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • DVD/CD drive will read DVD but not CD

    My DVD player plays DVD but not CD.  Whenever I try to play a CD, the player is a kind of hum noise.  Finally, the Player opens and a popup tells me to insert a disc.

    I tried a system restore and the automated Microsoft fixit tool.  Nothing has worked.

    I use Vista Ultimate.

    Any ideas?  Thank you.

    Hello

    Step 1: Please make all underneath the same if you've done it before as it's often the total of the process which
    solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
    Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
    This will refresh the default driver stack. Even if the reader does not appear to continue below.

    Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
    slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
    Playback of CD and DVD). Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry entries
    that the troubleshooter does not, and those who "could" be the cause.

    Check with your system manufacturer Maker and device for possible firmware updates and the good
    Your player registry entries.

    Here are the keys in my opinion, are those in question - for the reader of CD/DVD subkeys of course that he will be
    other subkeys in these keys. Be sure to ask specific keys involved as well as the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even registry settings correct for your CD/DVD drive
    a person with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • CD ROM will read/burn CD but not DVD

    I need my cd-rom drive to install a program for my security system and it would be nice to burn new CDs.

    * original title - I can't read CD or burn, but I can play DVDs / burn *.

    Hi dylan4x4,
     
     
    -Did you read/write on the CD without any problem before?
     
    -If Yes, what is the recent change that was made on your computer after that this problem started to happen?
     
     
    Try running the fix tool from the link given below and check if it helps in fixing the issue.
     
  • CD/dvd opens and closes and towers cd/DVD but unable to read the disc and is not recognized by pc

    No icon in my computer and the drivers does not work

    Hello

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Try this fix manually if the Fixit 314060 does not work
    http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

    Your CD or DVD drive is missing or is not recognized by Windows or other programs-
    a Mr Fixit
    http://support.Microsoft.com/kb/982116

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    for Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
    Vista installation after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and
    the correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD/DVD settings
    drive from someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
    nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

    DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
    devices and their properties in flat table, instead of the tree viewer
    http://www.NirSoft.NET/utils/device_manager_view.html

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • When I use my super disc to DVD recording, he plays on my IMac, but not on my dvd player.  I'm something wrong or just not do something?

    When I use my super disc to DVD recording, he plays on my IMac, but not on my dvd player.  I'm something wrong or just not do something?

    what you save? How do you save it? What format? what application? what you're trying to read on?

  • Satellite A50 will record on Dvd, but not on a CD - power calibration error

    My Satellite A50 will record on Dvd, but not on a cd. It happens with power calibration error after about 5% of the record.
    The drive used to save at all!

    --> Power calibration error is a mistake known to me.
    I've read on various sites several suggestions and comments and the power calibration error appear because the lens of the drive can not calibrate correctly.
    It is a hardware malfunction and unfortunately nothing :(

    You will need to replace the drive

Maybe you are looking for

  • Satellite L755-128 stop without reason

    Problem #1 when I play games after 30 to 60 minutes pc closed down and power led + battery led flashes orange Problem #2 a few times locking digital LEDs have a variable glow is like a light bulb that receive the variable power. Example of battery pr

  • Equium P200 1IR installation Windows XP problem - drivers SATA

    Nice day I'd like to know how to remove vista Toshiba model above and replace with win XP as HDD SATA refused to me. Your urgent response will be highly appreciated. Concerning kazeem

  • Which is the correct Point on the waveform of the Signal?

    Hello Please see attached image. I have labview software which is to measure the load of a load cell output. According to me, that the reading is accurate, except with the software Labview, we get up to 50 lbs less when we read it with the oscillosco

  • Failed to get the NIC to work - driver code 10 error

    I read a lot of similar posts, but not exactly like mine.  I've tried and failed on the advice given in other posts, so... Replaced the HARD drive in Inspiron 1420 my wife, Vista, Intel processor dual core T7250s Card Broadcom 802.11n Kept all the di

  • BlackBerry Maps or Google Maps

    Hello. I'm integrating maps in my application. Nothing GPS using this time just a map showing a location. The location only info I have is an address string that I will be back from a web service call, in other cases, we can access the latitude and l