DVD + RW disc in the DVD - Rom drive

Similar Questions

• Equium A60 freezes when I insert a disc into the CD-ROM drive

  Hello

  I have a problem with my CD drive - whenever I put a disc in it freezes the computer laptop everything! I can't do anything that even the mouse pointer hangs on the page.

  I have to close the whole pc and start again - what is happening again and again, but he will accept the disk of 1 to 10 times. The drive itself emits many noises whirring etc...

  Help!

  Rachael

  Hello

  My brother had the same problem with the laptop (not Toshiba).
  The whole operating system froze after the insertion of a disk of some. I put t remember if it was a DVD or CD.
  However, nothing works after a long investigation, I gave up and installed a new Windows OS.
  This helped and since the new installation of the OS, everything works.

  But this does not mean that this will help settle the question about the machine you!
  Maybe you drive malfunctions and must be replaced

• CD-ROM/DVD-rom drives will not play discs?... tried to be updated no joy... I tried the uninstall then re install just says code 39 error?. any suggestions?

  CD-ROM/DVD-rom drives will not play discs?... tried to be updated no joy... I tried the uninstall then re install just says code 39 error?. any suggestions?

  Try following the steps under "Windows XP" in the article following the MS KB:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• CD/DVD Rom drive reads the DVD as blank disc?

  Looked for information on the subject the whole place and it feels like I'm the only one who has this problem.

  The CD/DVD-Rom drive in my HP laptop is not reading the data on my DVD or CD I DVD that have been burned on a computer and some other that I burned on this drive. Data on them that I've used them in the past and without any problem. I changed nothing on my computer since the last time I used them I can think of and I have all the latest software updates for Vista and HP.

  Now when I put in drive it takes about a minute and then gets up and tells me that the disc is empty, but I know it's NOT like I've used it before and I see on the underside of the drive it was burned.

  Is this a problem of software or a hardware problem or disk I have not tried a lot of things that just the standard checks to try to get the drive to run but without success. For any help or suggestion would be greatly appreciated.

  Thanks Phil.

  Hello PhilStokes,

  Thank you for using the Microsoft Windows Vista Forums.

  Sorry, you have a problem with this issue.  I would first go to Device Manager to verify that all drivers are up-to-date.

  Go to start-> Type ' Device Manager "" in the search field-> select Device Manager '->, select here (+) for the CD/DVD - rom-> This will fall to the bottom of your device-> next right-click on the device and select update. "

  If not chance or driver is already updated, return to Device Manager and right click on your device and select uninstall.  You may be prompted to restart, anyway go back to Device Manager and right click again and select install or update.

  Please let us know status.  Thank you! Engineer James Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Can't detect CD/dvd-rom drives do not compact disc

  I have a HP Pavilion dv6 6090ee note book pc with windows 7 Home premium 64-bit sp1.

  Dvd/CD-ROM drives system does not. When inserting cd/dvd compact disc in dvd/cd rom show (E) cd player

  State of the Device Manager ("this device is working properly").

  Minhas

  Hello

  First, try the automated Microsoft fixit at the link below.

  Windows 7

  Check if the drive is now now reads disks.

  If it still does not work, click on the Menu start, open the all programs, open accessories, right-click on command prompt and select "run as Administrator".  In at the prompt, type the following command and press ENTER.

  sfc/scannow                (Note that there is a space between sfc and /)

  Let the entire process, then the output type and press ENTER.

  Then, click on the Start Menu, open Control Panel and click Device Manager.  Click to open the CD/DVD-ROM drives.  Right-click on the drive and choose uninstall.  Do not delete if requested drivers.  When the device has been uninstalled click the icon 'Search for hardware changes' (usually just below help in the toolbar).  Let windows reinstall the disc and see if it will now play discs.

  Kind regards

  DP - K

• Windows Media Center cannot detect the error DVD Windows Media Center cannot detect a DVD in the DVD - ROM drive. Insert a video DVD into the drive

  Original title: why Windows Media Center does not detect my DVD?

  I built my computer motherboard ASUS P658D, Intel i7 processor clocked at 2.6 gHz, 12 GB RAM, 750W Corsair PWR. power, Windows 7 Home Premium 64 - bit & ie9. When I put or the other two DVDs in one of two DVD players, Windows Media Center appears and when I click on "Play DVD" Media Center give me a window that says:

  "Windows Media Center cannot detect a DVD in the DVD - ROM drive. Insert a video DVD in the drive." Two DVDs, I've tried are educational for DVD

  my Nikon D300 Digital camera and a family video DVD or both these very well play in a bed of same computer running Windows 7 Professional 64-bit, & ie8.

  I tried Microsoft Fixit, no help. I tried to send Microsoft Support, and I got NO HELP. I did not bring any changes, and installed any program, just

  scoured the internet. A DVD player is a Sony Optarc with Microsoft Driver, the other is ASUS. I also tried to use Windows Media Player but nothing

  rises or it returns me to Windows Media Center and it does not detect to play either of my DVD. How can I get help here, or from Microsoft? Thank you.

  No, there is no yellow warning in Device Manager and the device manager says that two DVD players work properly. Mr. Fix it's

  automated download from microsoft that is supposed to automatically fix some problems, but he provided no help here. I think it is more likely

  that there is a problem with Windows Media Center or Windows 7 Pro 64 bit and either of my two new Sony DVD drives

  and ASUS.

  I thought my way in a solution. My thought was: Device Manager indicates DVD players work properly and both are new and we're Sony, and the other ASUS so I think only an unlikely problem with readers. The problem is with Windows Media Center "do DETECTED is not the DVD. So there must be a problem with Windows Media Center. I thought that I might need to reinstall Windows 7... then I thought that maybe if I just reinstall Windows Media that will work. He did. My problem was:

  Start > Panel > programs and features > features on or off Windows activate > then uncheck the box for multimedia functions > restart the computer > and then re-check the box to restore the multimedia features > now both discs play both DVDs, I tried. Both disks are operating normally. Reinstall the characteristics of media Windows 7 resolved the problem. Thanks to all who offered solutions.

• P50-A-144 satellite: the CD-ROM/DVD-ROM drive does not

  Version of Windows 10 Home 1607 (Build 14393.187)

  Hello

  After Windows Update Version 1511 1607, the CD-ROM/DVD-ROM drive does not work.
  The D: drive does not appear in Windows Explorer,
  CD-Audios and videos / DVDs do not work.

  In the Device Manager, the following legacy status error message appear:
  "Windows cannot start this hardware device because its configuration information.
  (in the registry) is incomplete or damaged. (Code 19). »

  Could you tell me how to solve this problem?
  Thank you.

  The solution was to uninstall the program "Toshiba Recovery Media Creator' and system settings/Programm features.
  I still don't understand why, but the fact is that after uninstalling the CD-ROM/DVD-ROM start normal work.

  More information here:
  http://www.borncity.com/blog/2007/08...-verschwunden/

• Satellite L300 - 1 4 PSLB8E - cannot open the CD/DVD ROM drive

  Hi, Bérard

  So I have a problem with cd/dvd rom drive.
  After that I updated with the last computer driversmy, the player can not open:(j'ai fais redémarre et c'est le même...) When I press the drive button to open, it flashes orange led for two or three times and nothing happens, the drive is always busy.

  Before reinstalling with the old windows version of the drivers worked well, but that sometimes it did not work... and now it's doing nothing all the time.

  Is my windows 7 x 64, updated drivers to update yesterday. Can someone help me?

  Hello

  You can find a small hole near the CD/DVD to eject the drive.

  Put a small card or PIN in this hole and the CD/DVD drive should eject manually.

  In my case, it always helps.

  Good luck

• My CD/DVD Rom drives read do not. Windows cannot load the driver for this hardware. The driver can be correpted or missing (code 39)

  How can I reinstall a driver of dvd/cd rom?

  Hi mourad,.

  1. have you been able to use the CD/DVD-Rom drive before with no problems?

  2. did you of recent changes on the system?

  This error occurs if the driver is corrupted or missing.

  You can read the following article and try the steps to solve the problem.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Hope this information is useful.

• My CD-ROM/DVD-Rom drive & the Bison Webcam built into my laptop. Does not work after I upgraded from Vista home premium to Windows 7 Home premium.

  My readers Optiarc DVD - RW AD-7530 ATA Device DVD/CD-ROM & the Bison Webcam built into my laptop. Does not work after I upgraded from Vista home premium to Windows 7 Home premium.
  Although of course, the CD-ROM drive worked during the upgrade.
  I noticed that when I turn firstly on the laptop, the last two lines of the front entry from Windows 7 are the following.
  PXE - E6i:Media Test Failure, Check Cable
  PXE - MOF: Exit PXE Rom
  During the audit of each Properties in Device Manager devices", I learned that they both work correctly.  In the list in the printers and the @Devices the only Webcam shown is also a "USB 2.0 Camera"
  Can someone help me please?
  Best regards
  John

  Besides what abdelhak says:

  The message of PXE boot that you receive when you start your computer has nothing to do with your CD/DVD-Rom drive. Your computer uses a PXE boot method to attempt to load Windows from a location on your network. Since you do not have this configuration, it is safe to ignore it. If it slows down the startup time of your system, contact your manufacturer and ask them for instructions on how to "disable PXE Network Boot of the BIOS.

  Hope this helps,

  Thank you! Ryan Thieman
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Viva Piñata was unable to locate the DVD - ROM drive

  Hello!

  I installed the game Viva Pinata on Windows XP Pro in English when I try turn on the game there is a message like: unable to locate the DVD - ROM drive.

  On the other computer (Windows 7) it works very well!

  What does not help?

  -Instalation of safedisc.exe.

  Help me please!

  Hi MarcinKowal,

  ·         Did you do changes on the computer before the show?

  ·         The installation of the game Viva Piñata was successful?

  You can read the following article and check if the problem still persists.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

  Let us know if that helps.

• The CD-ROM/DVD-ROM driver failed to initialize

  Keeps my CD/DVD-ROM driver not boot on the market.  Device Manager, says the driver is there, but it does boot, where will not read or write.  It's on an eMachines T3642 that came with Vista Home Premium.  The supplied operating system CD is available but not (obviously) read.  Help me not sysem restore... first restore point is September 22, 2009 and several dates different restoration do not help.

  eMachines support provides no answers on products out of warranty.  This set was purchased in January 2008, has worked very well with several old and a few new programs and material added since then.

  According to the diagnosis of Vista via the Device Manager, the failure of the pilot gave 37 error code.  The driver date is 21/06/2006, version 6.0.6002.18005,.

  Quandry: SOMETHING again loaded in via CD-ROM cannot load because the drive can't read it.     :-(
  The diagnosis of MS an available (on another window) will not download. (?)

  Color me irritated and frustrated (not a good fashion these days).  Help, please.

  Sincerely, Len Anderson

  Hello AF6AY,

  Have you tried to uninstall the dvd via the Device Manager drive then restart PC to see if Windows reinstalls? You can do it. If the problem is still there, can give a try? It is a quick easy fix from Microsoft, here is the link: http://support.microsoft.com/kb/314060. You need to uninstall all third-party software (example: Roxio, Nero, or iTunes) from your computer before you make this correction. After you restart, you can reinstall your software and try again to see if that solves your problem. Otherwise, it could be a bad optical drive. Hope this helps you. Let us know anyway. Make it a great day!

  "And in the end the love you take, is equal to The Love You Make" (The Beatles last song from their latest album, Abbey Road.)

• DVD ROM drive missing from the Explorer

  I installed nero burning rom on vista and then the dvd rom drive disappeared from the Explorer.  When I went into the Device Manager and checked my dvd rom for the solution properties, it says that the driver could not load and that Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19). How can I recover from this issue now? I don't want to reinstall vista or uninstall nero. But I want that this CD-ROM drive back in the Solution Explorer. What can I do or how I should do? I need a step by step procedure that can solve this problem.

  Try running the Fixit:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  You can also follow the instructions under "fix it myself", Windows 7 from Windows Vista.

  Important: The instructions, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows
  http://support.Microsoft.com/kb/322756

• my computer does not recognize the Device Manager cd/dvd/rom drive says corrupted or missing code 39

  my computer does not recognize the Device Manager cd/dvd/rom drive says corrupted or missing code 39

  Try following the steps under "Windows 7 or Windows Vista" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• The CD-ROM/DVD-ROM driver cannot be loaded by Windows and can be corrupted (Code 39).

  My DVD/CD driver drive HL-DT-ST DVDRAM GSA-T20N ATA Device cannot be loaded by Windows and can be corrupted (Code 39). How can I get the original device installed new driver if the CD/DVD drive does not work? It is available for download? Should it be first uninstalled and re - installed? A relative novice can handle?

  Hello

  Have you made changes on the computer before this problem?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Update the driver for the CD/DVD drive and check if that helps.

  Updated a hardware driver that is not working properly:
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Run the fixit for the following Microsoft Fixit and if it helps.

  Your CD or DVD drive cannot read or write media:

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Method 3:

  Uninstall and reinstall the CD/DVD driver and check if it helps.

  Follow the steps to uninstall and re-install the drivers.

  a. click on start toreduce this includes this im and then click Control Panel.

  b. click system and Maintenance, click Systemand then click on Device Manager.
  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  Reduce this includes this imageIf you are prompted for an administrator password or a confirmation, type the password, or click allow.

  c. in the Manager device, expand CD-ROM/DVD-ROM drives, right click on CD and DVD devices and then click Uninstall.

  d. When you are prompted to confirm that you want to remove the device, click OK.

  e. restart the computer.

  Hope the information is useful.