DVI - d does not work

I have a HP Pavilion Slimline s5-1110. I have a monitor connected to the VGA port. I want coonect to an HP 2009 m monitor using dvi - d port. I have connected the cable and get no signal on the screen. Is there some sort of video system requirements to use the DVI - D?

Hello

You can try to check monitor you OSD settings. Select DVI from the seizure. If it is not changed, press and hold the power button / stop for 20-30 seconds it has reset the settings

* By clicking on the laurels! White Star is a great way to say thank you on any post that you helped or solved the problem.* *.
* By selecting 'Accept as Solution' for an answer that solves your problem helps others who are searching the Web for an answer *.

Tags: HP Desktops

Similar Questions

  • U2412M does not work with DVI

    Previously worked perfectly with the following:

    Computer (Windows 7) supplied with monitor connected to monitor with original DVI cable

    Laptop Dell Inspiron 5547 (Windows 8.1) with a HDMI output connected to monitor via an HDMI to DVI I bought from Dell.

    Two computers worked with the VGA cable supplied with the monitor.  Now the VGA is intermittent.  I tested the cable with another computer and there is no problem.

    NOTE: I've never had the monitor connected to 2 computers, while they were on or while the monitor is turned on.

    Now, the monitor doesn't not with DVI - video display. The laptop cannot detect the monitor under control panel > display > screen resolution. It only detects the built-in monitor.  I can't check this on the desktop because there is no video display.

    I also bought a display port > HDMI adapter but read messages explaining the need for a converter, so I'll ignore for now it does not work with DP since I may have the wrong card.

    I followed the instructions to reset and diagnostics to the screen, which makes no difference. The problem is not at all, not only a bad display.

    Is still of Dell do not repair out of warranty monitors? I bought the monitor directly from Dell and I find it rather hard to believe that there is no way to repair $ 300 monitor that is only 3 years old.

    Any suggestions would be welcome. Or am I out of luck, and to buy a new monitor?

    You run properly bid. He says on page 31, 'you can run diagnostics integrated only when the video cable is unplugged and that the monitor is in self-test mode'

    So no DVI or VGA connected monitor.

  • HP Pavilion 500-277C Desktop P: DVI Port does not

    Second Montor doesn't work-

    I bought my HP Pavilion in November 2014 with two 27xi of HP monitors.  One is plugged into my VGA, the other into my port DVI port.  Well worked, until today.  MY DVI monitor is black.  I swapped the VGA DVI on the back of the monitors.  The issue moved to the other monitor (DVI cable), I checked the Device Manager and 1 single monitor is showon.  I did the updates of the pilot, no help.  When the computer starts, the DVI monitor is a different color and shows no signal, so I suspect the computer.  Thanks for any help.

    Hello

    If DVI does not work then try a known good DVI - D cable.

    As test, just try to use one monitor via DVI.

    Thanks for posting on the forum.

  • DMA2200 on PC-monitor does not work?

    Hello

    Well I have except the fact that the DMA2200 support not the VOB files, that the dvd drive is not region free and I had to reverse the mistakes of codes avi using the FourCC change codec, I'm surprised that I'm not able to see anything on a standard PC monitor.

    At first, I plugged the Componet video output (Y, Pb, Pr) of my DMA2200 directly on the vga input of the monitor (Dell 1900FP) with a cable special nine, but I saw just nothing more than a black screen. I changed the monitor for a LG Flatron L222WS monitor told me that the frequency was out of reach... Certain signals does not cross?

    But as the DMA2200 has a HDMI output that welland the Dell1900FP supports DVI - D Dual Link entry too, I. The 1900FP has a resolution of 1280 x 1024 and it can be run up to 75 Hz, 60 Hz it's native refresh rate. So, I went back to the store and bought a HDMI<->DIV - D Single Link cable.

    Only one? Yes, why not!

    DVI dual link as its name suggests has drivers more than the single link DVI for signal transmission. Single link DVI supports a maximum bandwidth of 165 MHz (1920 x 1080 at 60 Hz, 1280 x 1024 at 85 Hz) and use 12 of the 24 pins available. Dual link DVI uses all 24 pins available and supports a maximum bandwidth 2 x 165 MHz (2048 x 1536 at 60 Hz, 1920 x 1080 at 85 Hz).

    So, I plugged the HDMI<->DVI - D on the DMA2200, the Dell1900FP monitor and the monitor directly on channel 2: digital input. But... a black screen again. As I left the monitor rescanning the entrance, he tells me "Please press any key of the mouse button. It seems that the monitor sees a digital signal, but expected more... hmm... what to do?

    I tried to use NTSC (instead of our PAL) on the DMA2200 menu as the frequency changes, but it does not work. I also used all of the selections of entry on the DMA2200-menu (like composite-sd and hd). Normally, the HDMI options is grayed out and uses the default Auto option; but in composite-hd, my old TV mode (connected by SCART) turns black, but can still use the menu on the screen before the DMA and am able to change the HDMI settings, like 480 720 (if I remember correctly) and 1080 p (progressive format) and 1080i (interlaced). I hoped a solution here, but maybe it's just not my day.

    Then.

    Y at - there anyone out there that can help me to get a picture on the monitor? Whether vga or dvi - d... Please...

    Your Dell LCD and DMA2200 not being able to understand/sync between them with a direct DVI connection you could try to put a device inbetween them so that your Setup program can work. Try this device, basically, you connect the DMA2200 using RCA cables to the KWorld device and this KWorld device is then connected to your Dell LCD screen.

    See you soon.

  • Why is my second screen does not work - it starts with my main screen, but then turns off.

    My HP Pavilion P7-1120 Desktop PC does not work with two screens - there 8gig of ram...  1.5 terabyt hard drive, Windows 7 64-bit primary system works via the VGA port, but the second screen does not rest via the DVI port.  The two normal startup with the start-up of information on both screens, then the secondary display stops and I get a message "no signal".  Both monitors worked with my laptop PC and older myDell...

    When I go into the control panel and the view tab - the PC does not recognize the second monitor.

    GEO...

    It's not a problem with my PC or whatever it is in the box.  Cables work on other screens of the RGA and DVI.  There is a problem with my screen - the works of port RGA, is not the DVI port.  Another monitor works properly by the DVI.

    Now fixed.

    TKS for the entry.

    GEO...

  • Venue 11 7140 pro micro HDMI does not work after upgrade windows 10

    Has anyone tried connect a HDMI microphone on their place of dell 11 7140 pro after windows 10 upgrade? Mine does not work after the upgrade, but the HDMI from the dock works.

    I have thus display driver problems on 10 to win.

    For me, the micro HDMI port works fine. I use an active adapter, so that could make a difference.

    The HDMI on the dock works well, but only if I directly connect to an HDMI display. If I try to use a passive DVI adapter, then the external screen is not recognized. In addition, the DisplayPort on the wharf is also unnecessary, regardless of the type of cable or attached monitor.

    I encounter this problem after performing a new installation of Win 10, using the brand Dell drivers and latest drivers Intel installed by Windows update.

    It is certainly a driver problem Win 10 because everything works fine if I boot the Tablet under Linux using a USB key.

  • 3007WFP-HC does not work above 1280 x 800

    I'm putting in place two of these monitors but cannot get above resolution 1280 x 800. When I go to set my screen resolution, I have the opportunity to go up to 2560 x 1600, but when I select anything above 1280 x 800, monitors just flash of color bars.

    I use a NVidia NVS 310, two DisplayPort / Dual-Link DVI-D adaptersand two cables Dual - Link DVI - D (Dell NG032 to be exact). I installed the driver for the monitor (R222148). And verified that I have the latest driver for my video card is installed.

    Out of curiosity, I tried to use a DVI Single-Link cable and my screen resolution options changed so they maxed out at 1280 x 800. In addition, another strange thing is that, despite the possibility of going up to 2560 x 1600, the "recommended" tag is 1280 x 800.

    * The only resolutions supported by this nine year old monitor is 1280 x 800 or 2560 x 1600
    * Computer and/or video card with a DisplayPort on or Mini-DisplayPort will do only 1280 x 800, using any combination of wiring for the DVI converter 3007WFP-HC-D DL in the port
    * All HDCP content do it 1280 x 800
    * For 2560 x 1600, computer and/or video cards on the port and the cable should be DL DVI - D

    Even if the NVS 310 supports the conversion of DP adapter DVI - D DL, the 3007WFP-HC does not work. You need to remove the NVS 310 and install a video card with DVI - D DL dual output port.

  • HP 2159 m monitor audio does not work

    I would have assumed that the driver download, etc., would have set up correctly, but it does not work. (or I'm expecting something that does not happen?) For example, in listening to an Internet radio station, the only sound I get is from the hard drive & not the speakers in the monitor. Any ideas?

    How did your monitor connected to your PC?   VGA, DVI or HDMI?   VGA or DVI connections need an audio cable from the monitor to the audio output on the back of your PC.

    What model of PC you are using?

    I have this same split-screen on my e9280t PC connected via DVI with audio cable.

  • Safari does not work after installing macOS Sierra

    Safari and apple store does not work after installing macOS Sierra

    Alas, my crystal ball is in the shop for cleaning, so you will need to provide more details on what "doesn't work" and above all error messages. First of all, let's start the App Store. Provide as much information as possible for those of us who do not sit on your shoulder.

  • My iPad Apple 3rd generation wifi + his cell phone does not work

    MY 3rd generation Apple iPad, wifi + cell

    model number MD408LL/a

    Serial number DM * VGL

    THE SOUND DOES NOT WORK

    < personal information under the direction of the host >

    All sounds, or simply notification and sounds apps (for example do music and videos app still have sound)? If notifications and apps you have notifications on mute: on the iPad side switch - Apple Support ? If the sounds in all applications which have tried for example soft-reset/reboot of the iPad, insert/remove the headphones?

  • After recent, iPhone, 6, update, Windows, Explorer, does not work, see, iPhone

    I installed the latest update required for my iphone ios 6 a few days ago, and now when I try to download pictures from my iphone to my PC (via USB connection), the PC does not see the iphone.   iTunes sees it yet, but windows Explorer does not work.  It seems that some setting has been broken through the update of ios.  A way to solve this problem?

    Restart the computer and the iPhone. Unlock the iPhone before connecting it to the computer. Any change?

    TT2

  • Open the link behind Mail does not work

    Sierra using my link opened behind Mail does not work. The link opens on the top of the window.

    This option works for me in Sierra... is working for you with your previous version of the OS?

  • iPhone 5 home button does not work after ios 10

    My 5 Iphone Home button does not work after update final IOS version of 10.

    The home button works on the first push to wake the phone but it will not open the phone the second button.

    I activated the assist button, which does not work either. But what I discover is if I open device for assistance then touch and lock screen click on the button home will work once to open the phone. If I open any app I can't close it unless I go through the same routine.

    You attempted to restart your phone?

    You can do so by holding the sleep/wake button and the Home button simultaneously until the Apple logo appears

  • Do not disturb (on request) does not work

    I have an iPhone 7 more with iOS 10.0.2. I had set up as NEW when I got it. I use the function do not disturb I SLEEP every night to block the incoming notifications apps and emails (including work with the application Outlook email). I leave the phone won't cut not so I can make sure my alarm wakes me up the morning. But it does not work. I still wake up emails and notifications of the app. It worked on my old iPhone with iOS 6, 8, 9 or even 10.

    I see a lot of old messages and questions about DND not work, but they were more specific to older phones and ' iOS.

    Anyone else having this problem?

    Any ideas for help?

    Thank you.

    I'm sure that I understood this.

    I had "only when locked" checked and not 'always' in settings do not disturb.

    I leave my iPhone unlocked all night using the bedside table Central app as my alarm clock.

    There we go.

  • Contact ID does not work after update iOS10.0.2

    http://www.Macworld.co.UK/how-to/iosapps/iOS-10-troubleshooting-tips-3646690/

    Troubleshooting iOS 10 tips: Touch ID does not work

    Some users have reported that a previously happy Touch ID installation stopped working when they made the update to iOS 10. It is a pain, but rescuable - you will probably need erase your fingerprints and re-enter.

    First, however, try something simpler: go to settings > Touch ID & password, enter your password, then press the buttons next to pay Apple and iTunes and App Store so that they become white. Turn off your iPhone and turn it off again, then go back to settings and turn the two knobs back to green (you will need to enter your password Apple ID).

    Who fixed the problem?  I haven my Aff!

    If not, go through the fingerprint stored in settings > Touch ID & password - press each of them in turn - then erase fingerprints. Then go back and press Add A digital footprint and put back them in. It's a bit complicated, but it should fix the problem.

    I did all that, but the problem could not be solved.

    Try the following steps:

    1. go in the settings, press button ID & password, enter your password. Then turn off iTunes and App Store. Restart your iPhone or iPad. Return to Touch ID and password in the settings and re - turn on iTunes and App Store. Press Add a fingerprint to add another print.

    2 remove and re-add fingerprints: settings > Touch ID & password > enter your device code > scroll to find fingerprints fingerprints. Press the fingerprint, that you want to remove, and then press DELETE.

    3. restart your iPhone by pressing and hold the Sleep/Wake and home.

Maybe you are looking for

  • Apple ID to be used for work

    I have an apple using my work email address, as it was convenient ID.  Now, I get an iphone through work.  I've changed my email address on the old account, but now I can't use my work email address to install the new iphone.  What can I do?

  • I don't hear a thing from my computer. already troubleshooted. am I missing driver sound? What should do?

    -troubleshooted and still no solution -help please!

  • Deleted TUNMP. SYS and need to reinstall it.

    A few days ago my computer started having problems to download (very slow) emails and also a program file is 650 MB and it yielded to about 7 to 9 kps.  I went into the Device Manager and found a yellow exclamation mark under network adapters. Map Mi

  • Themes on Windows 7

    Hello I was bored of the interface of base of Windows 7 on my laptop and decided to look for some themes, there was not in the control panel (customization) so I decided to look online, found one that I like on Microsoft.com somewhere and you press '

  • Send all VPN traffic and the other end it blocks Internet

    Hello I wonder if I can get a RV042 VPN Tunnel to a RV082 and in the RV082 block all traffic on the internet that comes form the computers that are behind the RV042. Something like this: Remote PC-> RV042-> VPN-> RV082-> firewall RV082 (block interne