E PowerEdge T300 PERC 6I controller

Similar Questions

• Disc question PowerEdge T300 Perc 6 / I Raid 5

  I have a PowerEdge T300 with Perc 6 / I and Raid 5 with 3 hot swap 15 k 146 GB disks and 1 hot spare in the fourth slot from the backplane. Drive HARD 0 is orange flashing while HDD1 thru HDD3 are green. I have a new hard drive to install. I have to restart under the Perc 6 / I installation, disable HDD0, then turn the power off and replace it and walk back in Perc 6 / I and add the new disk and restart. Drive HARD 0 rebuild in the table or what I need to assign the new drive as the new hot spare? Are there instructions on how to replace a drive like that?

  Thank you

  Mark

  Once in the controller and you can just physically pull the failed drive. After removing, then wait a moment and insert the new drive. If the virtual disk has been degraded, then it should start to rebuild on its own once the replacement is inserted. If the virtual disk has been Optimal, then physically pull the drive and insert the replacement. Then in the BIOS OF THE controller, you can configure the replacement as a hot spare.

• PowerEdge 860 - PERC RAID controller compatibility

  I would like to add RAID 1 functionality on a PowerEdge 860 server we have at the office.  I was unable to determine what is the Dell Reference number for the RAID controller for that server.

  Is there a Dell RAID controller with BBU Cache memory which can support the PE860?   Would the PERC 5 / i raid controller work?  If so, what model number of Dell is compatible.  As the PE860 has long been considered his retirement there is nothing from the Dell Web site.  Searching the Web I found not less of 6 different numbers of parts Dell for a PERC 5 / i controller.

  Thanks in advance if anyone can be useful.

  -Paolo

  Hello Paolo

  PF100

  Is there a Dell RAID controller with BBU Cache memory which can support the PE860?

  No, the only supported the internal RAID controller is the SAS 5/IR. The SAS 5/iR has no cache. The PERC 5 / I is not supported on the 860. The only controllers that contain cache are external controllers as the PERC 5/e.

  You might be able to get a PERC 5 / i for work on the server, but we have not posted it to the 860. There is not many versions of the PERC 5 / i, which have been released, so I'm pretty confident that most or all of the part numbers you have found work. Whenever we change something on a part given a new part number. For example, if we decide to start using another antistatic bag to ship the PERC 5 / i in then we would give him a new part number.

  You can see here the valid controllers. The 860 is displayed on the inheritance tab:

  http://www.Dell.com/learn/us/en/04/campaigns/Dell-RAID-controllers

  Thank you

• PowerEdge 1900 perc 5 / I controller battery replacement

  I have a replacement battery message in the Application to manage Open Dell for a Dell PowerEdge 1900 Perc 5 / i controller. If I replace the battery I lose the current RAID configuration? Also all the procedures available for the replacement of the battery?

  Thank you

  Jeff Hicks

  Here is a link to the manual, page 92 will give you the steps to replace the battery: ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_poweredge/poweredge-1900_Owner%27s%20Manual_en-us.pdf

  Your RAID configuration is stored on the discs. Turn the power off and replace the battery, then start back. Upon request, accept the configuration of readers and move forward.

  Kind regards

• Dell PowerEdge T300 ntoskrnl.exe missing or corrupt [MS]

  Dell PowerEdge T300
  To: Win server 2003 32-bit st
  pOWEReDGE Expandable RAID Controller BIOS
  LSI 2007
  PERC 6 / i adapter
  6.0.3 - 0002 Pack FW

  It operating system starta no segnalando immediatamente di installare una copia del file ntoskrnl.exe

  Diagnostica no notes problemi hw

  It is properly Marin raid:

  1Protection drive found on the host adapter
  1 virtual drive managed by the BIOS

  Per ripristinare it Sop ho tried a con un disco di install di w2003 startare my non vede he raid e non ho a disposizione I driver (f6).

  Buongiorno,

  pilot of the it by it e perc6i controller he following:

  http://downloads.Dell.com/FOLDER97889M/10/DELL_MULTI-DEVICE_A07_R211422.exe

  Speaking saluti

  Manual

• Dell PowerEdge T320 PERC H710P Upgrade

  Dear support, I have a Dell PowerEdge T320 server that was purchased with a software RAID controller in S100.  I just bought a PERC H710P controller and hoped to help on the installation.  Do I need anything else to install the card as a set of cables?  I have a 8 x 3.5 "hot swappable backplane already installed with a pair of cables SAS that connect to the motherboard.  What else do I need to do this work?  I'm also not sure where the PERC H710P controller must be installed?  I can't find pictures or drawings on the Internet.

  Thank you

  Joe

  Jpmigliozzi,

  You should also order the cable (part # DJXF7) as well. This is the cable that connects the 710 in the bottom of the basket 8 x 3.5. Look at the picture below and let me know if those are the cables you already have.

  

  Let me know.

• PowerEdge T710 PERC H700 RAID level migration issue

  In my new role, I inherited a number of servers managed until now by someone else.  One of them is a PowerEdge T710 with a Controller PERC H700.  There are two matrices; the other has four 3TO disks in a RAID-5 configuration.

  I don't need the storage space any where near as much as the reliability factor.  Is it possible to do a migration on-site from RAID 5 to RAID-6 without disturbing data?  There is enough free space, and I have no problem losing a portion of the free space I have.

  "Is it possible to do a migration on-site from RAID 5 to RAID-6 without disturbing data?"

  Yes, BUT you can use this method by ADDING another disk.  RAID 6 requires a minimum of 4 drives.  Insert a disk "to hot', then in the software OpenManage (OMSA), go into storage, PERC, virtual disks and reconfigure in the drop-down list of tasks available for RAID 5.

  "There is enough free space, and I have no problem losing a portion of the free space I have."

  Apart from the fact that RAID 6 requires a minimum of 4 drives, even if you want to spend a 4 drive RAID 5 has a 4-drive RAID 6, it could NOT be done.  You can't make a smaller table.  The controller doesn't know - or care - on real data of BONE on the disks (so the amount of 'free space' is not serious) and is not worried about virtual disk space (which would be filled if the total capacity of the discs has been used).

• PowerEdge T310 - PERC H200 RAID1

  Hi all

  Bit of a newbie when it comes to RAID configurations in servers and wanted to ask a question.
  We have a server with a raid Perc H200 controller and 2 x 250 GB SATA HDD, which has the OS and 2 x 500 GB SATA HDD data/file sharing, both configured in Raid 1
  to provide redundancy. My question is, we want to replace drive HARD 2 x 500 GB with 2x2TB readers.
  I'll be able to replace the first 500 GB drive with the largest one, reconstruction can replace the second disc. The new 2 TB HARD drive will always appear as a 500 GB and if so, what can do to increase capacity.

  Thank you

  Charles

  If you replace each disc and wait that he rebuild, your table will always be 500 GB, and there is no way to use the extra space.  You will need to backup your 500 GB RAID 1, remove the drives, insert larger disks, configure RAID 1, restore the data.

• PowerEdge 2850 - Perc 4e/Di - status of the RAID-1 array

  I'm trying to give a sense of the info in OMSA 2.1.0 for a RAID 1 virtual disk on a server Poweredge 2850 + Perc 4e/Di.   Array disk 0:0 died at an unknown point in the past.  Info OMSA before replacing the drive:

  

  

  We have added another 0:0 drive, he rebuilt successfully automatically and this is the current info:

  

  

  

  So the State of the virtual disk RAID-1 is is more "degraded" and yet it is still showing only 0:1 Hitachi disk array and not the new 0:0 Seagate.  How this should be interpreted?  We also have another virtual disk raid 10 on this same server with discs model even who had also a drive down and replace this trained player the new Seagate drive not appearing in the table of Raid-10 list as expected.  the difference was that the Raid array-10, the original disk was displayed in OMSA as 'impossible', while on RAID-1 above, no other player has been listed.

  It should show the other disk.  A few things to try:

  • Refresh the screen VD
  • Closing/re-open OMSA
  • Stop/re-start services OMSA (DSM)
  • Clear the ESM/Hardware log in OMSA
  • Restart the server
  • Updating system firmware (BIOS, ESM, PERC (first pilot), HARD drive)

  All the foregoing may work, but it's probably caused by obsolete OMSA and/or firmware/drivers.

• PowerEdge 2900 Perc 6 / i internal Raid Controller

  OK, so I use a server Dell PowerEdge 2900 with a PERC 6 / i integrated RAID controller

  I have configured the RAID array very well, installed Windows 2008 R2 and works fine and dandy

  The only problem I encounter is that, when starting the server (Post), I get a message on the cable SAS B are not connected or misconfigured.  The bottom of the basket on my server, which goes to the internal drives, has only a port where I can plug a cable between the Perc 6 / i.  Where is the 2nd wire supposed to go?  I can't find the second port.

  Thank you

  Hello

  joeyjojo56

  I get a message on the cable SAS B are not connected or misconfigured.  The bottom of the basket on my server, which goes to the internal drives, has only a port where I can plug a cable between the Perc 6 / i.  Where is the 2nd wire supposed to go?  I can't find the second port.

  PERC connector 0 goes to the bottom of basket. Connector on the PERC 1 connects to the modular Bay. If you don't have the module Bay optional then you ensure that you use the 0 on the PERC and not the connector 1.

  Thank you

• Looking to replace a RAID in older (UCS-61) with a new (UCP-51) Perc 5i controller on a PowerEdge r610 server...

  Hello world

  I'm looking to get RAID 5 in an old R610 capabilities we have laying around. The new controller seems to be compatible with the server and he knows well. Whenever I start the server with the new Perc 5i card it gives me:

  "Invalid pcie card found in the internal storage location.

  System stopped! »

  Is there a step in this process I am missing? This is my first time doing something like this and get beat. If I put the old controller to back in or no controller at all, it starts without a problem. I've updated the BIOS BIOS server Dell R610 version 6.4.0.

  Any advice would be greatly appreciated.

  The PERC 5 is not supported on the R610.  You need the PERC 6 / i.  The PERC 5 might work, but you cannot use it in the location of storage dedicated; you will need to try another location PCIe.

• PowerEdge R230 add RAID controller

  Need advice: the goal is to add Dell PowerEdge RAID Controller H330 server Dell Poweredge R230.

  Originally, the data connection is to the motherboard with a mini SAS connector, power cord is related to the Board of Directors itself as well go with a connector 6-pin. Given that the new RAID controller has a different SAS (SFF8644) mini connector, I can't use the original cable.

  So try to solve that I bought 4 X SFF-8482 SAS a cable - Mini SAS SFF 8643. It would connect the RAID controller for readers. (THIS)

  I also added a power cords: 4 Pin IDE power Molex 1 male to 3 x female Splitter & 2 x 4-pin Molex to 6-pin PCI-E adjust Power Supply Cable (THIS) and (THIS). It was supposed to feed readers - but is not and they won't turn on.

  No idea why? Other ideas of ways to solve this problem?

  Thank you

  IB - EN1

  1. initially, I understood the topology based on the information on the user manual, see the attached figure describing Cabling two 3.5-inch hard drives 'to the PERC card. Isn't this relevant?

  The information I had previously provided are based on the wiring of the Controller PERC H330 with basket 4 x 3.5 "which I assumed you had based on your notes. Thanks for your clarification and ignore these P/Ns. Here are the cables you need.

  • Signal and cable LED to P/N 6R7VT the H330 controller to connect to the motherboard
  • Cable SAS junction A H330 for 2 hard drives or optical drives, P/N TTN3V
  • Hard/optical drive power cable from the system board P/N N9P7R for 4 HD (shipped with your server. Use only 2 connectors) or P/N VXR2 for 2 hard drives.

  IB - EN1

  457CH, TWV59, 6R7VT: I can not find an any of them on the dell Web site, you can share links?

  I would recommend that you directly contact Dell sales in your area.

  Thank you.

• PERC 6 controller

  Buongiorno,
  Ho need di ricevere quotazione by Controller PERC 6 UN tag del prodotto service: B36HS3J

  PowerEdge 2950

  Rimango in attesa di a gentile riscontro vostro.

  Buongiorno,

  Server it ha più di 8 anni, the material party non sono più available per questo Server unfortunately alla vendita.

  Todas

  Marco

• DELL PowerEdge T300 boot CD

  Hi, my T300 PE with Windows Server 2003 keep restart when loading Windows, I need to repair operating system , but I lost the CD to boot for my T300.im of PE begging you to give me the link (if able iso link) where I can download it.

  Thank you very much!

  Let me be more clear... you can NOT repair the BONES with SBUU.  The only thing that will make SBUU is to help you to re - install Windows and it will be, WIPE OUT, all the information on your current disks!

  You said Server 2003 won't start - it keeps just reboot to the Windows form.  If you want to solve this problem, you need to boot CD of the 2003 version of the Recovery Console.  Since 2003, cannot communicate with readers without a RAID driver, you will need to load the RAID driver (below) of a disk at F6 during installation of Windows (the first thing you see when you start on the Windows CD).  Since your T300 probably does not have a floppy drive, you will need to use nLiteOS.com to integrate this driver (text mode) in the middle of 2003.

  If you don't care about the data on the disks and want to destroy any re - install Windows, then use SBUU, but who does not resemble what you're trying to do.

  RAID drivers:

  Use this option if you have a PERC 6/i:

  Use this if you have a SAS 6/iR controller:

• Batteria per PowerEdge 2950 [MS] 6i controller

  Buonasera, abbiamo UN powerEdge 2950 tell di batteria del controller Perc 6i auswechseln che a bordo. Può inviarmi tempi di delivery e quotazione del componente?

  Use e mail: [email protected]

  Grazie e buona serata.

  Eseguito ordine: th di Ricevimento Ordine: customer 292356836: 3228826 - INTERLINEA S.R.L. N ° di Re: 15440626

  Speaking saluti

  Manual