E0Q10AV: Laptop is no longer sleep properly after the upgrade of the SSD.

Hey there!

My laptop Pavilion 15 t-n100 touchscreen goes to sleep when the lid is closed properly, or even completely off when said. He enters this weird State where the light on the power button and the WiFi switch light goes orange but continues to stay on. I can't turn on the laptop by pressing the power button or the keys on the keyboard. Battery regularly and soon enough, the computer laptop completely off. I can also get to fully power off by pressing the power button.

This occurred after I reinstalled the operating system and everything on the computer from scratch when I swapped in a Samsumg 850 500 gb SSD. (Totally worth $ 175 given the speed boots and program begins are!) I do not think that I hung it bad, but I'm open to said if I did!

I already have:

  • Checked to make sure that "Wake on the keyboard" is enabled. This is the case.
  • I looked for a new BIOS on the support page - http://support.hp.com/us-en/drivers/selfservice/HP-Pavilion-TouchSmart-15-n100-Notebook-PC-series/54...
  • Absolutely no BIOS is available for this computer on any page of HP.
  • I ran the HP Support Assistant who was installed with the laptop.
  • I ran the Intel Driver Update Utility 2.2. It's all there.
  • Sometimes, when I run the online tool for updating my computer on the HP support page it will tell me that there is a recommended Intel MEI to install. I told him to do, and then he tells me I'm downgrading when I do this. Should I try a MEI decommissioned HP?

Help! -J' tried a ton of stuff and I'm exhausted! I even actually posted in a forum instead of just research and TAPI and try until I have understand

Steve

Advertisement

Steve

you have different problems

Displays the Windows Home or Pro Version 10

You are doing home-PRO system

Samsumg 850 problem you need to install the software of Samsung for PC Wizard

Magicain install use them Samsung hibernation settings

Your Sytem Page

HP computers - sleep and Hibernate issues (Windows 10 )

install the intel update of mei 9.5.24.1790 1.5 M

install the new HP Support Assistant you of new drivers and bios for install

Tags: Notebooks

Similar Questions

  • Send a message that the computer does not shut down properly after the resumption he out of the hibernation mode.

    My laptop has Windows Vista and is about 3 years old.  It is in excellent shape, but recently it has been brought to my attention that whenever I put into hibernation mode and resume, I receive a message that indicates that the system or computer is not stopped correctly, and so I have to restart the computer.   Why is this happening? and any solution for this?   Thank you in advance.

    Hi SuzanneSchwester,

    Thanks for posting your query in Microsoft Communities. It seems that you are getting a message that the computer is not shut down properly after the resumption he out of the hibernation mode. Provide the following information:

    ·         Did you do changes on the computer before the show?

    ·         What is the brand and model of the computer?

    Follow the steps in the article.

    You have problems after you resume Windows Vista from sleep or Hibernate computer

    You can see these articles for more information:

    Solve power problems

    Turn off a computer: frequently asked questions

    I hope this helps. Let us know if you need more assistance.

    Thank you.

  • The screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. What should do?

    I installed upgrading W7 W8. Already during the final phase of installation, the screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. I tried the settings of brightness through the hardware buttons and in energy savings, but it remained the same. What should do? Karl

    Looking for a display updated sony driver.   Its always a good idea to do so during the updating of the OSs.

  • 14 - n001TX: HP laptop shutdown properly after the upgrade to windows 10.

    After that I have upgraded my computer laptop 14-n001TX HP for windows 10, is not shut down properly. It propely to stop after 5-10 minutes, but is not shutdown properly after working more than 50 minutes-1 hour.  When I stop the laptop, the screen turns off but fan, the led power and seeing the "f12" key not turn off.

    Then I went to Power Options > choose the power button > change settings that are currently unavailable > UNCHECKED enable fast start. But still the problem was not resolved.  In addition to "sleep" mode in my laptop is not working properly. When I go to display mode standby turns off and rest works. But the laptop wakes again if I press a key. At this time I have to press and hold the power button until the laptop stops. I do the same thing when my laptop is not shut down properly.

    (This occurs even in windows 8.1). What is the solution for this problem?

    Hello

    Try the following.

    Open settings and select System.  Select food and sleep, and then click additional power settings - in the next window, click on "Choose what the power button" in the left pane.

    In the next window, click on "Change settings that are currently unavailable" (close), then Remove the check mark from the box against 'Turn on a quick start (recommended) '.  Click on the button Save the settings, and then close the open windows and restart the laptop.

    When windows has reloaded, download the driver directly from Intel IMEI on the following link, unzip the and run the installer.

    https://Downloadcenter.Intel.com/download/26127/Intel-management-engine-consumer-driver-for-Intel-nu...

    Once the installation is complete, restart the laptop.

    When the machine rebooted, re - activate the quick start and restart the computer once more - let Windows take over completely for a few minutes before checking.

    Kind regards

    DP - K

  • HP pavilion n003tx: MY HP laptop does not shut down properly after installing windows 10

    My HP laptop worked perfectly with windows 8.1. After the upgrade to windows 10 is not shut down properly. Power and wireless signals is always bright and also consumes the battery.  I need to press the button for at least 4 seconds power in order to stop completely.

    Is there any possibility to get rid of this problem

    Spoiler (Highlight to read)

    When I disabled the quick start in power options > it works very well with a certain delay before start-up

  • computer does not work properly after the update, because the screen is black.

    Advice please! :-(

    After an update there about 2 months, my computer has never worked properly after that I turned it back. My windows start page is longer there. My screen is black. The words are only in white and fluorescent yellow...

    The only way I can go online to find Norton (is always at the bottom of the black screen) and go to help. I can get a search bar like that. Almost as if this black screen hides everything below.  Computer is 13 months old.

    My internet provider says it isn't them. Gateway said it's not my computer so idk what happened after this update.

    Any advice would be so appreciated.

    Thank you.

    Hi Patty,.

    Welcome to the Microsoft community. I would be grateful if you can answer these questions.

    1. You have installed the latest drivers for Windows 8?
    2. What is the model number for Gateway computer?

    If you get a black screen after upgrade to Windows 8, it might be due to an outdated or incompatible graphics card driver. Update to the latest version of the display driver should fix this.

    Try to remove all external devices connected to the computer and then try to start the computer and check if it works. Follow these methods and check if that helps:

    Method 1: To resolve this problem, update the Gateway website. video card driver

    Step 1: Check out these Microsoft items for additional reference:

    Download and install the drivers

    http://Windows.Microsoft.com/en-in/Windows-8/all-drivers

    Step 2: If you are not able to find drivers for Windows 8 to HP support. Try to install the graphics drivers in compatibility mode and check:

    Download your applications and devices in Windows 8.1

    http://Windows.Microsoft.com/en-in/Windows-8/get-apps-devices-working

    If the problem persists, proceed to the next method.

    Method 2: I suggest to follow the suggestions provided in this Microsoft KB article and check if this can help:

    Windows 8 starts with a blank screen after a standard or hibernation

    http://support.Microsoft.com/kb/2756559/en-us

    See also the suggestion provided by Scott (owner of Forum) from this thread and check if this may help.

    http://answers.Microsoft.com/en-us/Windows/Forum/windows8_1-performance/black-screen-when-logging-into-Windows-80-or/93bb4530-C31C-4a2d-91e6-7ec2fc420379

    I hope this helps. If you need help with Windows, let us know and will be happy to help you.

  • FN key is not working properly after the upgrade vista on Satellite A100-334

    After I upgraded my NB A100-334 PSAA9E the Fn keys no longer work. Have downloaded all the drivers offered by Toshiba on their site. A positive result. Can someone, please. THA Flowbee

    Hello

    usually to use your keys FN you must download software toshiba special tools to enable this FN - key feature.
    Where the drivers have downloaded you´ve? Have you tried tools in the same place? If this isn't the case, then you´ve has got a new mission. :)

    If Yes and you didn t find anything so here try:

    http://209.167.114.38/support/download/ln_byModel.asp

    It s toshiba canadia Web site. Maybe you will find the tools here.

    Good luck
    Welcome them

  • Keyboard and mouse did not work properly after the service pack 2 update

    key Board runs very slowly and mouse runs through the screen when it is used. Acer Aspire 5050-3371 came with Vista home

    Hello

    Do you use a touchpad or mouse wired / wireless?

    Your laptop is connected with laptop keyboard?

    I suggest you to check if the keyboard and mouse work will find in safe mode. Follow the steps that will help you perform the following checks:

    Method 1

    a. restart the computer.
    b. start typing the F8 key.
    c. you get early boot option window.

    For more information, see: the boot advanced (including safe mode) options

     

    After the entry into SafeMode Log in your user account and check if the keyboard and mouse are working.

    After you perform method 1 Troubleshooting and if you find the keyboard and the mouse does not work correctly then you can perform the following procedure.

    Method 2:

    You can also perform the clean boot and check if you are able to start successfully. Clean boot will start Windows Vista by using a minimal set of drivers and startup programs and helps eliminate conflicts of third party software.

    The following link has steps showing how to perform the clean boot: http://support.microsoft.com/kb/929135

    Note: Please make sure that the computer is configured to start as usual according to step 7 of the article: how to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7:http://support.microsoft.com/kb/929135.

    Hope the helps of information. Please post back and we do know.

  • How can I get my laptop to recognize my printer wireless after the automatic update?

    After the automatic update I couldn't open any program (Word, Excel, internet etc.) that I managed to resolve by restoring my laptop settings before the update. It seems to have worked until I went to use my printer. My laptop will not find my printer through devices and printers, and when I go to print a document, an error box pops up saying "Windows cannot print due to a problem with the installation of the current printer.

    Your help would be appreciated gratefully.

    You must view the windows update history and the KB updates that have been installed, that you believe that the cause of the condition.

    And also to give the brand / model of the printer and the laptop

  • PP 2015.3 Edit to tape function suddenly not working properly after the update

    I have maybe in a small percentage. I have grown to love PP and have been using it for controlling certain emissions tape HDSR. I think I went from 2015.0 a.3. The reading seems to have suffered in this update. I get now loss of images of PP did not keep in touch with the reading. So put together it on tape fails and insertion don't will go not to the point where there was a framework has fallen.

    There are a few other issues that are easy to manage, but tried to go through telephone support on this issue.

    -Insert video or audio over half the time after insertion is finished, PP gets stuck. The Strip was inserted but the glass remains and to pass to the next punch that I have to cancel the dialog box.

    -PP will are not more than 8 channels of audio. -Final Cut 7 can arm all12, available on our SONY SRW-5800.

    -After the 2015.3 update the PP would go through the motions of insertion on the Strip, but it would not actually insert audio, so if I was not paying attention you'd think they had set just a note QC. But no! PP just doesn't work. This problem has been resolved by removing the preference PP folder in My Documents on Mac OS X.

    So my main problem still remains that reading is basic and is no longer usable for laybacks professional Ribbon. I had to go back to Final Cut 7 and snap a simple 422HQ to tape. There must be something that I am missing, but the time allotted to me to troubleshoot this with time etc etc is limited. What could have changed in the update for the functions to change the band which makes it unusable now?

    I want to really just to install the old version, but phone support wasn't helping me with that and said I couldn't.

    Mac Pro 5.1 12 Core

    OS X 10.10.5

    32 GB OF RAM

    NVIDIA GTX980

    PP 2015.3

    Black Magic Decklink Extreme 3D +.

    Video Fund 10.6.2

    Tape recorder plugged with cable RS - 232 9-pin

    Adobe must have heard our complaints.  The new update of PP 2015.4 seems to have resolved most of the questions that we take.  I always have a random frame dropped here and there.  Export to tape option is viable again in PP 2015.4.  I'm under PP 2015.4 with the latest drivers from the AJA.

  • fonts Mathematica does not properly after the senior at el capitan

    I used Mathematica 5.2 on my MBP with Mountain Lion. After the upgrade to El Capitan, there is a problem loading the fonts and Mathematica does not load correctly. Any ideas? Wolfram has a package of fonts, but don't know what fonts to download or how to install them on my MBP. Any ideas?

    Please, back up all data before proceeding.

    Launch the application book fonts and validate all the fonts. You must select the fonts in order to validate them. See the built-in Help and support article for instructions. If the font book detects any problems, solve them.

    Start in safe mode rebuild the font caches. Restart as usual and test.

    Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or the boot volume is a software RAID, you cannot start in safe mode. In this case, ask for instructions.

    If you still have problems, then in the font book menu bar, select

    The file restore Standard ▹ fonts...

    You will be prompted to confirm and then enter your administrator login password.

    Also note that if you disable or remove built-in fonts, for example by using a third-party font manager, the system may become unstable.

  • Satellite A50 - 109 fan works not properly after the HD upgrade

    Yesterday, I upgraded the HD of my laptop A50-109 of 3 months. The original HD installed in the laptop was (to my surprise) a Fujitsu HD 40 GB 4200 RPM 2 MB cache.

    So I've upgraded to a Toshiba 80 GB 5400 RPM 16 MB of cache and had to re - install Windows XP Pro and all the drivers of toshiba.

    Now, since the upgrade, the fan is constantly working even when CPU power, cooling method and all the others are on the lowest setting possible. Before the upgrade, the fan would obey the parameter of cooling method and the fan would be COMPLETELY silent, IE does not work because there was minimal use of the CPU, etc.

    Now the situation has changed, and the fan runs constantly no matter what use. I am terribly disturbed by noises, and I see no reason for the change.

    Is there a solution or should I return the HD or laptop?

    Hi Simon,.

    A very interesting discovery.

    Kind regards

  • Play Lenovo Vibe K4 Note mobile store does not properly after the recent update...

    After the last update, my game store does not work correctly. A lot of apps is not proceed with the installation an error...

    Help, please

    Hi Digambar,

    Welcome to the community of Lenovo!

    Please perform the below mentioned the troubleshooting for the troubleshooting steps:

    1. go to settings--> Apps--> all Apps-> Google Playstore: clear the Cache, erase the data
    Note: All browsing history will be get deleted.
    2. If the problem is persists kindly update the playstore Google later.
    3. make sure that the update of the system is up-to-date.

    Please come back to us if the trobleshooting helped you.

    Thank you & best regards

  • PC laptop Envy 17: Envy 17 laptop PC fingerprint reader works only after the start

    The fingerprint on my Envy 17 reader reads only a fingerprint the first time that I connect once the system is booted (after shutdown or restart). From time to time, it will read once the system is locked, but that is extremely rare. I put the system in place using my MSN account and also configured SimplePass with default settings. SimplePass version is 8.00.57.

    I looked on several other issues in the forum and did not find something like this. Other issues reported when related to player doesn't work do not, for example. I found a few link in some messages describing such tasks that go back to a previous version of SimplePass.

    I don't know if it is related to my problem or not, but I noticed that the drive light sometimes flashes a sequence once the system is running. It seems that when the light flashes, it will not be read. It stops flashing when I placed my finger on the reader. (I think that the typical sequence is 3 flashes, pause, 1 flash. This cycle repeats.) This isn't always for that well, and I have found no correlation between the flashes and the measures taken after the initial logon.

    I made the fingerprint reader driver, rather than later.

    I uninstalled SimplePass (after update to the last with no luck) and the drive works fine now. I use RoboForm for my password management and it supports using the fingerprint so I'm covered there. I guess it should be renamed "SimplyNoPass."

  • Devices may not work properly after the upgrade

    While trying to update, I received this message:
    "These devices does not work after the upgrade.
    Before the upgrade, we recommend that you update the drivers for those devices.
    Cancel the upgrade, open Control Panel and search for
    "update device drivers", or select the instrument manufacturer
    Web site to search for updated drivers.
     
    Storage controllers: controller IDE ASZE9NGB

    I searched Google, Bing and Microsoft and... nothing. Please help me! Thanks in advance!

    This diagnosis you have done to date?
     
    Did you look in Event Viewer?
     
    Error messages?
     
    Please provide details about your current problem.

    We are better able to help you if you help by providing us with as much information as possible...

    Suggestions for asking for help on a site.

    http://support.Microsoft.com/kb/555375

    http://www.CatB.org/~ESR/FAQs/smart-questions.html

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_other-windows_update/what-information-to-post-in-the-Windows-Update/1467f44b-ee27-4F7D-98d7-f1c4b35b3395

Maybe you are looking for

  • LINUX and satellite L20

    HelloI have a TOSHIBA Satellite L20 - 182 notebook (PSL2XE) and I want to change my OS from Windows to Ubuntu Linux.Unfortunately, I couldn't find a drivers for my laptop that runs on Ubuntu Linux. So my question is - where can I find the drivers for

  • GEYED icons in Device Manager

    In Device Manager, I have a long list (gray diamond icons some more dark grey with a black outline) under the title "-pilot no Plug and Play" if I right click on the paler gray icon then 'properties', I see generally the following "currently, this ha

  • User profile why does XP Home disappears

    I would like to know which situations of XP Home user profile disappear?

  • Mutual redistribution between EIGRP and BGP and match statements

    Hello Experts I'm working on a problem of mutual redistribution between EIGRP and BGP The idea is a beacon (210) on traffic from our LAN on R2 - 2 so that it can be put in correspondence and denied the R3-7. The goal is to prevent routing loops. The

  • HP Pavilion G5418uk

    The HP Pacilion G5418uk there a connector 6 power pins? The internal connector that can be used to power the video cards. I asked twice for questions before you buy. First time, I got a response but avoided my question and asked me to buy a computer.


HashFlare