E4200 limited to 20Mbps

Similar Questions

• E4200 limits in Bridge Mode

  Hello

  My setup goes like this: I have a fiber to Ethernet from my ISP connector. The Ethernet cable going to one ISP has published my Zyxel router. In this router fixed phoneservice connects to give us a landline VoIP service (which is cheaper). An Ethernet cable going to the Internet port on the E4200 to the Zyxel router LAN port. That works fine but I had to put the E4200 in Bridge Mode so that it can connect to the Internet through the Zyxel router I need to use phone services my ISP provides.

  I bought the E4200 because I wanted to use the dualband functionally and get an 802.11n 5 GHz network configuration and to give me the ability to block certain Web sites and services that I know Cisco/Linksys is famous for--the ability to control your network.

  Well, imagine my surprise when I couldn't use the Parental control settings when the router is in Bridge Mode. This is the reason why I bought this router on an Apple Airport extreme. Is there anyway to allow me to use the Parental control in Bridge Mode or a better way to connect to the router with the rest of my network?

  Thanks for any help!

  If you do not have devices (mainly the game features) which require an open NAT, you can connect an ethernet cable from the Zyxel router to the Internet port on your E4200 and simply use it as a normal router without mode bridge.

  Make sure that the ip address of the E4200 is on a different subnet (just change the third octet (to the third decimal number) to something different than used as IP default Zyxel.

  You could call your ISP and ask them how to dumb down the Zyxel so that you can use the E4200 as main router and Zyxel as a modem too.

• E4200 descendant speed limited to 6 Mbps

  I posted this in the forum of wired, because it is the wire speed is limited, but it seems that there is so more expertise E4200 here, here, it's once again:

  I have a fiber service Hotwire and the plan is supposed to provide 20 Mbps downlink speeds.

  I just bought a Linksys/Cisco E4200 to replace an old Dell TrueMobile 2300 of 2004.  With this router, I had announced full backward speed.

  Now, when I run a speed test with the E4200 in place, the downlink speed is only 5168 Kbps or more.  Watching the test speed meters, I see the data arriving in bursts, all a few seconds than a whole bunch of it gets through, and then for a second or two, nothing.  It's pretty steady.

  But if I run a speed test with the cable to connect ONTARIO directly on a laptop, I see 19001 Kbps - pretty close to 20.  It is the same cable that plugs into the back of the router.

  With E4200 in place

  

  Live in laptop

  

  Any ideas that I can check or set in the E4200 to change this behavior?

  -Christmas

  OK, do the senseless thing and going through all configs and just try the options and re - test every time, I have found a setting that seems to have bypassed the problem...

  I enabled MAC address Clone (it has been disabled by default) and cloned Mac. my PC

  I can only guess there is a problem between the router and the Motorola HAVE.  Maybe they don't like Cisco and arbitrarily limit the speed if they feel a Cisco's Mac address?  I know, it's a stretch.

  In any case, I'm happy.

  -Christmas

• Wired download speed limited to 6 Mbps, without a router E4200 is 19 Mbit/s

  I have a fiber service Hotwire and the plan is supposed to provide 20 Mbps downlink speeds.

  In fact, if I run a speed test with the cable to connect ONTARIO directly on a laptop, I see 19001 Kbps - pretty close to 20.

  But when I put my new Cisco's E4200 in place, the downlink speed drops to only 5168 Kbps or more.

  I see the data arriving in bursts, all a few seconds than a whole bunch of it gets through, and then for a second or two, nothing.

  Surely, this router should be able to go this fast.  My old Dell TrueMobile 2300, which replaced this new model of Cisco, capable of handling the full speed, and it was made in 2004!

  Any ideas I could check or set in the E4200 to change this behavior?

  -Christmas

  OK, do the senseless thing and going through all configs and just try the options and re - test every time, I have found a setting that seems to have bypassed the problem...

  I enabled MAC address Clone (it has been disabled by default) and cloned Mac. my PC

  I can only guess there is a problem between the router and the Motorola HAVE.  Maybe they don't like Cisco and arbitrarily limit the speed if they feel a Cisco's Mac address?  I know, it's a stretch.

  In any case, I'm happy.

  -Christmas

• Linksys E4200 - can update firmware and roll backs damage my router?

  Hello

  I had to restore the firmware on my Linksys E4200 (v2) because I had problems after upgrading the firmware. I tried to upgrade again and again met with problems. In short, I improved a few times and restored several times. Currently I'm on the old firmware and I without any problem.

  In the old days, it was not wise to update the firmware of some peripheral hardware too often, because some devices has agreed that a limited number of updates to firmware... don't ask me why :-)

  Is this also the case with the Linksys E4200 or can I upgrade and roll back as often as the requires, or as often as I want to try to upgrade because of new features...?

  Thank you

  SJW

  As long as you do the right steps during the upgrade/downgrade the router (loading the firmware using a wired computer, not to interrupt the upgrade/downgrade process, load the right file, etc.), the unit should be fine.

• Support USB E4200

  The web site says that the E4200 has a USB port to connect printers and USB drives.  That sounded to me like several devices could be added.  It is not only to be able to connect to one.  Since I have 3 USB drives and 2 USB printers, which sounded a lot.   Implementation, it seems that this port will not use a hub and can be used for a USB device.  How can this be?  Which is so limited as to be almost useless.  Is there any way around this?

  Their intention was to a device that will be used at a time, not two. AFAIK, there is no away around it, and I'm sure that material limitations are to take account of this.

• E4200 Base on a browser utility unavailable

  I manually configured my E4200 (v1, material, v1.0.03 firmware) months ago and it worked perfectly.  My wireless PC and connected to the Internet perfectly.  I connected the utility based on a browser occasionally when I needed to upgrade the firmware or my DSL flaked and I needed to restart the E4200.  My problem is now I can't connect to a browser-based utility.  Connectivity Internet is fine.  I brought any configuration changes.  When I connect to the URL I get the certificate error message "there is a problem with the security certificate. of this Web site", which is normal.  I then click on the link "Continue to this website (not recommended).".  It would normally ask me to connect.  Now, it just displays the error "cannot display the webpage".  I hit the factory reset button and that reset the configuration to connect to the utility based on a browser.  I then rebooted my. CFG file that contains the right configuration, I saved when I could connect to a browser-based utility.  Afterwards I couldn't connect to a browser-based utility.  I tried again the factory reset button and re-flashed the v1.0.03 firmware, then reloaded my. CFG file.  Same result.  Does anyone have any suggestions?  Could this be a hardware failure?  It makes no sense to me that software would suddenly cease to work without configuration change.  (I have over 30 years of experience in the COMPUTER industry, so I know that some of you will be skeptical about the claim that "I don't change anything.")  But really, I wouldn't change anything.)  Thank you.

  All,

  I've seen the same behavior: not being able to connect to the console (default 192.168.1.1) browser while the router works fine, all PCs are online and you are able to ping the router, ipaddress, and netbios name.

  Reading this thread: I remember also have increased the level of security by limiting the "HTTPS" console only a few weeks ago (by deselecting "HTTP"). This behavior appears on W7, 64-bit with IE9, but also with Chrome and Firefox.

  It was a simple solution (in my case):

  Connect a / or walk on it for a Windows XP machine in your network (with IE7 or IE8).

  connect to the console of the browser (by default: HTTPS://192.168.1.1).

  Provide your admin and credentials

  And voila, you're in.

  Configure the router to also allow HTTP then (to improve security uncheck the abilty to connect to the console via WLan)

  Apply the changes and you're done.

  (If you walk on it for your W7 IE9 machine you will notice that you are able to connect again).

  I hope it will work for you as it did for me.

  PS If you use HTTPS, your browser will complain about an invalid certificate, it's OK because it's a (sort of) SelfSigned certificates not provided by Trusted Third Party (Verisign / Digicert etc.). Since you are the connection to that source in your own home, that you trust, it's good to ignore the warning and continue on the console.

• Function of more limited rotation on imac than the iphone!

  I just realized that the edit > function of rotation is more limited on Photos/imac compared on my iphone.

  It is surely not good! On my 27 inch screen it only allows me to rotate 90 degrees, but on the iphone I can adjust to any angle that I wish, and it also gives a grid to help align things.

  Maybe it's a setting I'm missing - otherwise I find it's a huge gap for not being able to properly rotate the photos on my imac.

  In Photos on my Mac 2.0,.

  -I select the picture

  -Click the button to reveal the editing tools (top right photo window, to the left of the Details button)

  -then right click on the first symbol third with two arrows dotted ("crop" in French...)

  -then click, hold down and up and down

• I have FaceTime disabled through restrictions on my daughter's phone.  However, she is still able to make and receive calls FaceTime. If it is limited, how this phenomenon is happening and is there a way to prevent it from happening in the future?

  I have FaceTime disabled through restrictions on my daughter's phone.  However, she is still able to make and receive calls FaceTime. If it is limited, how this phenomenon is happening and is there a way to prevent it from happening in the future?

  How do you know that she can always use Facetime?

  Could she learned/guessed the password restriction?

• iCloud Sync Limitations

  I have two questions (so far)

  1. I have sync had the records office and Documents on my MacBook Pro, but I can't go on my iMac, because (to quote the error message) "you have too many files, too many files in a single folder, or too many folders nested in your Documents or files from office."

  I have a lot of capacity iCloud passing, after having updated in advance.

  Does anyone know what the limits are or where to find them?

  2. what happens if you have the same name of folders on two Macs and try to synchronize the other?  for example if you have the same software installed on both machines you might have a folder of Documents/Adobe on each example.  If a folder is renamed automatically, I fear that it could affect the application next time it is run.

  For your first question, I do not know what are the limits, but what happens if you were to move some items from these folders and subfolders?  Which would be then able to synchronize your documents easily?

• VPN connection error - pppd limited

  Hi I think I have a problem with OX, the captain and the networks, I sail perfectly with the team but since update stops running the VPN, I tried the possibility to go to recovery mode to 'disable csrutil' then ' sudo chmod u + s / usr / sbin / pppd "but it does not work when you use Netextender or FortiClient." I have another Mac with Lion and works properly the only difference I notice in the file 'pppd' Captain makes me 'limited, compressed' and only 'compressed' Lion I put a photo and a newspaper of netextender:

  15/09/2016 10:15:59.271 [603 General info] NetExtender 8.1.788 for Mac OS X initialized

  15/09/2016 path of the bundle app NetExtender 10:15:59.299 [General info 603] = /Applications/NetExtender.app

  15/09/2016 createLogPanel() 10:16:01.045 [gui info 603]

  15/09/2016 10:16:01.730 [config info 603] loading saved profiles...

  15/09/2016 10:16:16.507 [connect info 603] user: "prueba".

  15/09/2016 10:16:16.507 [connect info 603] domain: "abcd.hos."

  15/09/2016 10:16:16.509 [connect info 603] Server: 'vpn.abcd.es:444 '.

  15/09/2016 10:16:16.581 [603 general notice] connection to vpn.abcd.es:444...

  15/09/2016 10:16:16.820 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)

  15/09/2016 10:16:16.821 [General notice 603] retry...

  15/09/2016 10:16:16.822 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)

  15/09/2016 10:16:16.823 [General error 603] authentication failed: connection failed. See the log for more details.

  15/09/2016 10:16:16.823 [General error 603] NetExtender connection failed.

  15/09/2016 10:16:16.823 [General notice 603] SSL VPN disconnect...

  15/09/2016 10:16:17.058 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)

  15/09/2016 10:16:17.058 [General notice 603] retry...

  15/09/2016 10:16:17.060 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)

  15/09/2016 10:16:17.061 [General error 603] disconnect command failed

  15/09/2016 10:16:17.063 [General notice 603] SSL VPN connection is completed.

  15/09/2016 10:16:17.063 [config info 603] loading saved profiles...

  15/09/2016 10:16:17.065 [gui info 603] connection failed. See the log for more details.

  

  I think that the problem is a network file or because I put the wrong password and I cannot detect this error. as I said the VPN working properly with another MAC using the same network.

  Help...

  You shouldn't be messing with the security features of the operating system.

  Problems may have to do with the network, or client software that you use.

  I start by making sure all the software are updated and then create a new entry, vpn, double control system that everything has been entered correctly.

  FWIW, I use the built-in features of VPN on El Capitan to connect to my University regularly and without problem.

  I'm not familiar with "Fortinet", and I suspect that you may need to be updated, or simply use the built-in VPN.

• There should be a limitation or personal parental control on hotspot. Children feel obliged to allow their friends to use their hotspot. And the parents who pay for it!

  There should be a limitation or personal parental control on hotspot. Children feel obliged to allow their friends to use their hotspot. And the parents who pay for it!

  This is a user to user support forum, so there is really nothing anyone here can do for you, I'm afraid.

  However, you can send your comments Apple

  http://www.Apple.com/feedback/

• How to overcome the limits of mail?

  I want to send a mass email to more than 100 people. How can I exceed the limits of sending mail?

  You can use a Gmail account with the e-mail. Their limit is 500 recipients for a single e-mail.

• How can I disable limited Mode for watching Youtube videos?

  How can I disable limited Mode for watching Youtube videos?

  You need the restriction code to disable restrictions.

  UPDATED - revised to include the correct article for Mac.

  OS X El Capitan: set up parental controls

• Zoom is limited, even with Zoom.maxPercent to 99999

  I can zoom in only a few times (8 times the default value). I used to be able to zoom in more, then Zoom.maxPercent has been introduced and limited, but through the: config I could change that. Zoom.maxPercent changing has no effect more either.

  I don't know what is happening. I can zoom in now, but do not know how I got there. I suspect that restarting a profile was not enough to reset Firefox. I had to close all. (I wanted to be able to zoom in a new profile, but why I couldn't enlarge my old profile for awhile? Don't know.) Anyway, of course I don't have a zoom of 50 value. The first time I've changed these values I didn't know what I needed. As to why, I use it to design layouts in fr 'em zoom to see the effects sensitive (b) want to blow up Chinese characters and Japanese easily for inspection or copy (c) it allows to make quickly the images that use glyphs (the interface to paste the glyphs into Gimp is heavy). -Thank you for your time.