E430 - no internet - but can connect to the network. Any idea?

Similar Questions

• I am not able to connect to the main wifi network but can connect to the network of comments.

  Hello

  This is something new, I am facing to where I am not able to connect to a main network of airport extreme, but can connect to the network of comments. Guest network works perfectly fine while the main network does not connect to devices in the home. I also found that none of my base stations are visible in the airport utility (I Airpot extreme and Airport Express on the same network). Help, please.

  The first step in troubleshooting with this type of problem is to perform a complete network power cycle on your network. If you decide to do...

  Power off all the devices on your network... modem, routers, computers, printers, etc... in any order you want.

  Wait a minute

  Turn on the modem first and leave a few minutes, he managed by itself

  Turn on the next device that is connected to a modem and leaves turn a good minute

  Keep turn on devices one by one at a time, one minute apart, until the entire network is back

  Recheck the network and report on your results

• Home wireless network users can no longer connect to the internet via router, but can connect to the network

  Modem Arris Touchstone telephony Windows Vista on PC, router Linksys WRT54G2, Netwk disk, Set netwk as private.

  My father's home network no longer works. All Pc's are running Vista. DSL is connected to the Modem Arris. Modem is connected by ethernet to the LinksysWRT54G2 router, that is connected to the PC. Other Pc is able to connect to the local network, but not to the internet. Main PC connects to the internet with a separate connection. See the other PC on the network. Daddy has no save the password and can not get him out of Linksys.

  Never mind. After 6 hours I fixed it. I don't know how I did it, but I think it was because I have unplugged and pressed the reset button on the modem for 10 seconds.

• can connect to the network but not internet XP

  I use a computer on a local network xp, can connect to the network, ping the DNS server, gateway, etc.  However, I can't not conncet to internet.  When I ping a web address using the address of the site name or xxx.xxx.x.xx I have no success.  Tried to reset winsock, tcp/ip, without success.  Would appreciate any help.

  First course of action:

  1. turn off the PC.

  2. turn off the router.

  3. turn on the router.

  4. turn on the PC.

• no internet but not connected to the wireless router

  I have 400 SL with windows vista installed.
  Everything worked well for years, until a few days ago.
  It is the symptom, and what I've done:
  1. the laptop CAN connect to the wireless network, no problem, very strong, just signal has no internet.
  cannot ping google.ca.
  In network and sharing Center:
  Computer---> network---> Internet
  ^                   ^
  |                     |
  Red Cross OK
  2. all other devices (iphone, ipad, other laptops) can connect to the network and internet.
  3 did a system restore on the eve of this stoppped working. always the same.
  4A bought a wireless adapter, always the same. but it works fine on the other laptop
  5 tried to set a static IP, subnet mask, gateway, still the same problem.
  6. any other device can ping each other with the exception of this laptop...
  7. the seller cordless tool is uninstalled (Lenovo connection management tool)
  8 rebooted a million times between all the steps
  9 safe mode with network has the same problem.
  10 tried to use other wireless, still the same problem...
  need help...
  Thank you
  -Virginia

  Hi Virginia,

  Thanks for posting your query in the Microsoft Community Forums.

  After the description of the problem, I understand that you can not connect to a wireless network on windows vista computer.

  I appreciate your efforts on this issue, however no need for you to worry we are here to help and guide you in the right direction.

  Help me with the information below.

  -Don't you make changes on the computer before this problem?

  I suggest you to disable temporarily security software and then check if you are able to connect.

  Method 1

  You can also temporarily disable the security software and check if it works.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important: These steps may increase your security risk. These steps may also make the computer or the network more vulnerable to attack from malicious users or malicious software such as viruses. We recommend the process that this article describes to enable programs to operate as they are designed for, or to implement specific program features. Before you make these changes, we recommend that you evaluate the risks that are associated with implementing this process in your particular environment. If you decide to implement this process, take additional measures to protect the system. We recommend that you use this process only if you really need this process.

  Method 2

  Reset the router and see if that helps.

  Note: to help you reset the router, you can consult the manual that came with the router or the router contact manufacturer.

  You can see this help article.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• Why can't connect using Apple Airport WIFI of my remote security cameras but can connect using the Xfinity WIFI Modem/Router open?

  Why can't connect using Apple Airport WIFI of my remote security cameras but can connect using the Xfinity WIFI Modem/Router open?

  Two possibilities:

  (1) your airport WiFi might have a network name that is not in line with best practices, wireless

  A good wireless network name is...

  ... In short no more than 20 characters

  Simple... no special characters like an apostrophe, dollar sign, asterisk, etc.

  Compact, without spaces in the name

  For example, a wireless network network name as... red .dfedoryk Apple wireless network... .is not what you want. Something like... .dfedorykwireless. .. masse are much more likely to connect to non-Apple devices.

  Same guidelines your password

  (2) Apple gives the same name to network 2.4 GHz and 5 GHz network that produces double router band.  Some non-Apple devices are confused by the present, you may need to use the option to assign a different name for the network of 5 GHz on the router from Apple. Then, 'point' your device to the network name specific to which you want to connect.

• Unable to connect to creative cloud but can connect to the adobe site... Please help

  Unable to connect to creative cloud but can connect to the adobe site... Please help

  already done. without success. now chat with adobe helpdesk. Thank you

• Problem of password of account, without that we can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid.

  Hi, I hope you can help with this problem. A friend has 6 computers networked to a Tower Server and have a problem. A worker student put computers into hibernation, and since then, nobody can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid. I tried to get into the pc to try removing network and replace it, but I can't get on the Administrators account because it has been disabled. I'm at a loss on how to proceed. My friend cannot afford a service call, so I'll try to help him.  Thank you

  If the computer is on a domain then there are at least two accounts that can be used to remove the computer from the domain:

  • A domain administrator account.
  • A local administrator account.

  When your friend has launched Windows for the first time after buying the machine, he was prompted to enter the name of an account. This account is created automatically with administrator privileges. He should use it now.

• My Windows XP home edition with service pack 3 now displays the status of my absorbing as "State of the network" wireless network connection but never connects to the network.

  My Windows XP home edition with service pack 3 now displays the status of my absorbing as "State of the network" wireless network connection but never connects to the network. This started after my last Microsoft update has been installed. .

  original title: status: network address acquisition
  Hi BKlap,
   
  Try these methods in the order.
   
  Method 1: Repair the network connection to solve the problem.
  For more information, see:
  To force a network adapter to acquire an IP address
   
  Note: The information in the article applies to Windows XP Home Edition as well.
   
  Method 2: Follow the steps listed in this article to resolve the problem:
  How to troubleshoot connectivity TCP/IP with Windows XP

• Cannot ping the default gateway with Centrino Advanced-N 6235 on XPS 12 but CAN connect to the Internet

  I have a XPS 12 with an Intel Centrino Advanced-N 6235 wireless card.  I can't ping the default gateway with the wireless card.  When I use a USB network adapter, I can ping the default gateway for the wired connection.  I can connect to the Internet and the internal network with the wireless card and can ping other computers on the network.  I am trying to run a program to connect wireless to a projector.  I have two different programs for the two different projectors.  I can connect by cable but not wireless.  I think that the problem is anything that does not make me a ping of the default gateway or something on the wireless card.  I have a 10 latitude with a Broadcom wireless card that is connected to the same access point and can ping the default gateway and can connect wirelessly to two projectors.  They all have two windows 8 Pro.

  I downloaded the new drivers from Dell, uninstalled, reinstalled, tried to update Windows install the drivers, all with no success. Any ideas?

  The solution of the problem by chance.  I was connected to the computer with a different network than what has been used to authenticate user account on the wireless.  When I switched the user account for the user account that was logged on to the computer was the same who authenticate to the wireless, it worked.  Go figure!

• Can connect to the network, but not the internet, a "Local" access only

  Just installed a new router and am now unable to connect to internet on my HP laptop. The laptop is running Windows Vista 64-bit Service pack 1. Pulling him diagnose & repair window returns a message indicating "your modem or router is not available.

  I tried several things to get the internet to connect. I have reinstalled the driver, turned off the firewall, disabled the Internet Version 6 (TCP/IPv6) Protocol and manually configure the network connection.

  I have a desktop computer with a wireless adapater that performs the exact same OS as the laptop and I have no problem with this connection.

  I am able to connect to the internet if I connect the laptop to the ethernet cable. I am completely confused and would appreciate any advice!

  Hi Ima be,

  You can follow the steps below and check if that helps you solve the problem.

  Method 1

  Try to power cycle the router and the computer and check if it helps.

  On the PC:

  1. Save your work and restart the machine.

  On the router or modem (if wireless printing):

  1. Unplug the router and the modem.
  2. Wait 30 seconds.
  3. Plug in the modem and wait for it to come to the ready state.
  4. Plug in the router.

  After you put cycle check the connection between the router and the computer.

  Method 2

  If the steps above do not help, you mayreset TCP/IP stack. To reset access the link below and either click on "Fix it for me" or follow the instructions to fix it yourself:http://support.microsoft.com/kb/299357
   
  Disable the IP helpdesk:
  1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter
  2. scroll down to the IP assistance service, right-click on it and select Properties
  3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.
  4. then click on "Stop" to stop the service from running in the current session
  5. click on OK to exit the dialog box

  Method 3

  Disable IPv6 and remove IPv6 virtual cards:
   
  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.
  NOTE: You should do this for each network connection, even if they are disabled.

  Method 4

  Disable the DHCP Broadcast Flag:
  Link: http://support.microsoft.com/default.aspx/kb/928233
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://support.microsoft.com/kb/322756.  How to back up and restore the registry in Windows
   
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
   
  To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:
  1. Click Start, type regedit in the search box, and then click regedit in the list programs.
  2. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  3. Locate and then click the following registry subkey:
  4 HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}
  5. in this registry path, click the (GUID) subkey that corresponds to the network adapter that is connected to the network.
  6. on the Edit menu, point to new, and then click DWORD (32-bit) value.
  7. in the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.
  8. right click on DhcpConnEnableBcastFlagToggle, then click on modify.
  9. in the value data box, type 1 and then click OK.
  10. close the registry editor.
   
  By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.
  You can also try uninstalling and reinstalling the driver for the wireless card.

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• WRT1200ac and WRT1900ac OPENVPN can connect but can not see the network

  I can connect but can not see the computers on the network. I've tried everything. Any help would be great. Thank you

  Firewalls are disabled on remote computers?

• Unable to connect to creative cloud but can connect to the adobe Web site

  I can connect to the Web site, but the creative cloud says that my password is incorrect every time
  I tried to change my password and it will not always open a session

  Windows or Mac?

  
  

  Tried to reset password of the Adobe Creative Cloud app?

  1)
  

  

  2)

  

  
  

• Satellite A200 - can connect to the network (LAN & WLAN) but no Internet

  Hi all

  I have a problem very annoying and confusing.

  I've just set up my internet connection at home. From the beginning, my Toshiba was unable to properly communicate with the router to set up the connection, I had to use Mac. my partner

  After much time spent talking with the ISP and the manufacturer of the router, I was told that there is a problem with my network card - it is not compatible with the router. I don't think that this is the case, my laptop is fairly new, newer than the router actually. So, it seems a logical explanation. As this laptop was able to connect to every other internet connection as needed. And more importantly, my phone can communicate with the router as I can connect 'local only' but not to the internet. I get an error that can not diagnose Vista.

  Device Manager shows that my wireless and ethernet devices are working properly.

  My network settings are also on the parameters required by the router.

  I'm at a loss total, and personal support from my ISP and DLINK (manufacturer of the router). Any help / advice would be GREATLY appreciated!

  Thank you

  Edward

  Hello, Edward

  This explanation of compatibility is for me nothing else good joke. I use PC Toshiba laptop for years and none of them has a few special network adapter.

  Can you please as first step test the functionality of connecting your laptop to another router? Maybe some friend of you can help.
  When you connect your laptop using the cable LAN is green LED on ONE LAN port?
  You see a flashing orange?

  Do you have access to the settings of the router using internet explore on your Satellite A200?

• L755 satellite internet connection drops but stilll connected to the network

  Hello

  I hope one of you can help me. I have a laptop 13 q Satellite L755 nice for a year and a half.

  My problem is that I surf the net and suddenly my internet connection drops down. On Firefox or IE, I have a message with a triangular signal yellow saying: "your connection has be revived."
  I'm still waiting on my network but I can't access the internet.

  The strangness, is that my family other PC or laptop have no problem on the connection.
  This happens on the wifi and cable. At home or other places of connection.
  In France and the United States. So my conclusion is that there is a problem with my laptop.

  I looked around some forums. It seems that some have a problem with IPv6.
  I have disabled the option to use IPv6 on my laptop, but I still have the problem.

  Another comment: I play the Kingdom of the fortress online.
  Sometimes I disconnect from this game but I can still surf the internet for a few minutes before undergoing a total disconnection.

  Looking forward for your help.

  As this happens using WLan and LAN its really hard to say why your connection is interrupted.
  Have you tested the internet connection with fresh preinstalled system?
  I mean it is possible that some software / updates received or installed in the past it would affect.