E5 - 522 will not start past logo

Similar Questions

• error code 213:19 what is?  Photoshop Elements will not start past this error message.

  What is the error code: 213:19... Photoshop Elements will not start past this error message

  Error 213:19 | Problem is the license for this product

• HP Pavilion will not start past blue hp invent screen

  My computer does not boot past the blue hp
  Invent the screen. I took the sides off the computer. I started and I realized what was the noise that I heard and whence he came. It's the hard drive makes a noise like a fan starting then a rattling noise. Then it stop trying to load and is repeated several times, then closes. I unplugged the power supply for the drive hard drive now it
  take care when I unplug it but I can't do anything without hard drive.

  Your hard drive has failed. If you are still in warranty, contact HP to send a new hard drive. If you are out of warranty, it will be much cheaper to buy a retail hard drive to replace the original. Hope you have a value recovery disk?

• A500 will not start loading Logo Android guard, never rooted always Stock Please Help

  My son has tried many password twice and locked our tablet. I tried a few steps on the hard reset and now it shows Anroid on the screen, then turns off, then goes back to the Android screen stuck in a boot loop that follows. It will never start. I have a card in it but its Blanck and it seems that is where the restoration seeks to draw. Please can someone help me with this on the acquire reloaded and return to stock. Thank you.

  You need to format the Tablet again.

  Press the volume low botton and bttm power at the same time when the Tablet vibrates release the displaced volume due to the orientation of the screen from one side to the other, when the little letter come release all funds and do a factory reset.

  If this does not work, lets say when you lock the unit with the password after that 30 minutes, it will come out to you to try again.  If something happened to send it to the service.  Be aware that this may be a reason for 1000 even a bad MB.

  Good luck

• My iMac will not start past the gray screen

  At startup, the iMac rings and goes to the grey screen where he hangs up and does not progress.

  I tried with the command/R button from Mac, but the utility never appears.

  I tried to start with the SHIFT key down... same thing.

  Is there something I can do?

  Thank you very much!

  Paul,

  My iMac (early 2010) has just started doing the same thing.  Initially, I could start in recovery mode, but download time was 18 hours and time increased.  I stopped the download and downloaded the installation on a USB disk on my MacBookPro in the hopes that I could start the iMac to the USB instead soon and not tomorrow. Now, I can't get the computer to boot on the USB stick or the recovery partition.

  So he can start on the USB key you must hold down the option key when you hear the chimes boot.  Then maybe you can try and have some success.

  If you find something that works to post here, if you think about it!

  Good luck!

• C satellite will not start - only toshiba logo appears

  My laptop is only 1 week and will not start.
  All I get is the toshiba logo and the screen becomes a pale bluish color.

  Any ideas?

  What is your laptop model?

  You are able to access the BIOS?
  Turn on the unit button and press F2 to enter the BIOS.
  The BIOS screen is visible?

  Another idea: the laptop turns on, press the F12 key.
  Usually, you should see a start menu. Here choose the last option called HARD drive recovery.
  This option allows you to recover the computer laptop back to factory settings.

• My dell optiplex 740 will not start. The screen is black, once it displays the Dell logo. It does not say that the computer is in mode 'sleep'.

  My dell optiplex 740 will not start.  The screen is black, once it displays the Dell logo.  It does not say that the computer is in mode 'sleep'.

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You receive an error message?

  Method 1

  See the articles below and check if it helps.

  Computer stops responding with a black screen when you start Windows XP

  http://support.Microsoft.com/kb/314503

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

  Method 2

  I suggest that you start the computer in the last good known Configuration mode and safe mode, post back with the result.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  How to fix a computer that does not start

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/how-to-fix-computer-that-will-not-start

  Method 3

  If the computer can boot in any mode, then I suggest that you perform the clean boot procedure and check if it helps.

  It is possible that some third-party programs installed on the computer is causing the problem.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• Windows XP will not load past the Blue error screen

  Hi, wondering for a while if someone can help me...

  My xp system will not load past the Blue error screen that is displayed when the computer stopped suddenly or inadequate.

  No matter what are the measures that you choose to take (safe mode, the most recent configurations... etc) the system will just beyond the blue screen on the windows logo download page, where the loading bar moves about 10 seconds before returning to the blue loading page.

  So far I have tried to leave the computer as long as an unused months while I was abroad, remove the battery for varying amounts of time and leaving the computer as long as a day.

  In the absence of a recovery disk, I have no idea how to do to return to the form and would like to receive advice or suggest, keeping in mind I'm not a computer genius (if had'nt you may have guessed). Preferably, without losing my element pictures and videos stored on the hard drive, but it's just preference.

  Thank you, Jay

  Hello

  It does not seem good friend if the Windows operating system does not start even using safe mode, then I don t think you will be able to run the operating system without new OS reinstallation. :(

  To back up data from the HARD drive I recommend that you connect the internal HARD drive to external USB HDD controller and a backup of the HARD drive on another computer.

  Then you could try to reinstall the operating system on your laptop using the Toshiba Recovery CD

  See you soon

• L50-A-19N satellite will not start in the BIOS

  Hello

  I have a problem with my laptop.
  I have installed 8.1 and fedora 20 windows.

  I was in fedora, when I decided to restart Windows.
  Instead of grub, I saw message with the error and my notebook has stopped booting.

  I pressed the power button / stop, he died but when Im trying to start it again, I see the logo of Toshiba Leading Innovation and that's it.

  It will not start any further.
  I decided to get my system, but when I press F2 or F12, nothing happens.
  I can't get into the BIOS!

  Please, help me to solve it.

  Somehow, this seems really strange
  I m wondering why you are unable to access the BIOS

  What you can try to do is, remove the laptop HARD drive and switch on and press F2.
  From my point of view of the rare even if the isn't HARD drive connected, you should be able to access the BIOS.

  But for Pierre, I'm not very well your laptop problem is related to the faulty / corrupt Boot partition m

  However, your comments would be greatly appreciated

• L775-11N satellite will not start

  Hello

  I bought a L775 almost a year ago, but today it has stopped booting. It freezes at the screen of the BIOS (Toshiba logo).
  No HDD LED activity, but all the others are fine.

  I think that the HARD drive is defective, as I traded with my portable Linux and it works.

  However, (a Seagate Momentus XT ST95005620AS) HARD drive works on another computer and even on Linux with the Toshiba (on an external HARD drive enclosure). He has some bad sectors (INTELLIGENT default), but it works as it should.

  I tried to clean the CMOS memory, wipe the HARD drive (using GParted), but nothing.

  Any ideas?

  I think it fails because of the CHIP, as the BIOS will not start on this HARD drive because of the errors, but I'm not sure. I tried to update the BIOS (I think that I've upgraded to 1.90 but there is a 2.0 release), but looks like it is a Windows software only.

  Thanks for your replies

  EDIT: I can boot the disk when it is inside a USB enclosure.

  Hello

  I don t think that this question is related to the failure of HARD drive.
  Even if the HARD drive is faulty, the laptop must pass the POST (power self test) properly but it doesn t it freezes to the Toshiba start screen and this means that the POST has not been passed

  I think you should check the RAM. A faulty RAM can cause this kind of problem
  Otherwise, it could be a serious problem with the motherboard.

• Equium L10 will not start

  Please help - my Equium L10 will not start.

  Power supply is OK. When the power is connected the orange battery light comes on. I press the power button the green power light turns on momentarily (literally a Flash), then both the Green and orange lights out with orange alone returning it on about 2 seconds later.

  Else does nothing - no fan activity, no hard disk, no activity of the screen activity, no other light - you get the picture!

  I tried the following:
  Removed battery and tried to start with AC power not only - no joy
  Removed AC power and I tried booting with battery only - no joy
  Barrette of RAM removed and reinstall - no joy

  Does anyone have ideas before considering a tech? Suggestions (with the exception where to paste!) would be welcome.

  Kind regards

  Gary C

  Hmm .He doesn't sound good. For me, it looks like a motherboard problem. It is maybe something wrong with electronic power to the Board of Directors of s. But not for sure.

  What you can do is to remove the battery and unplug the power adapter for a while.
  Wait about 20 minutes and connect the battery and adapter for the laptop. Then try turning on the laptop computer.
  If this does not help I recommend contact the ASP technician, because I don t think you will be able to know what's exactly wrong.

  So I hope that the technician can find the fault quickly and can solve this problem.

  Good luck

• iMac will not start. From sound and sometimes Apple, but no further details. How can I get?

  Just got an iMac and it will not start up.  I can get the sound start and, sometimes, the Apple logo, but it stops there.

  Have tried to use 'command-option-P-R' together. Have you tried "D".  Tried "control C".  Are there other possibilities that I could try?

  Install or reinstall OS X from scratch

  Make sure that you have backed up your files because the following procedure will remove all of the hard drive.

  HD recovery start:

  Restart the computer and after the buzzer, press on and hold down the COMMAND and R until the menu screen appears.

  Erase the drive:

  1. select in the main menu disk utility and click on the continue button.

  2. once the charges of THE select your boot volume (usually Macintosh HD) in the

  list on the left. Click on the Erase tab in the main window of THE.

  3. set the type of format Mac OS extended (journaled). If necessary, click

  Security and button all the option data from scratch in a single pass. Click

  the clear button and wait until the process is complete.

  4 leave FROM and return to the main menu.

  Reinstall OS X: Select reinstall OS X and click on the install button.

  Note : You will need an active Internet connection. I suggest to use Ethernet if possible

  because it is three times faster than wireless.

  This should install the version of Mac OS X that you had installed it.

  If this does not work then your hard drive has failed and must be replaced. Please make an appointment at the Apple Store - Genius Bar store and bring it into service. If you are in the United States or is unable to make an appointment in this way, contact your Apple store.

• Computer laptop HP Presario CQ57 (Windows 7) will not start.

  Computer laptop HP Presario CQ57 (Windows 7) will not start.

  Memory test: past

  Smart Check: spent

  DST short: failure

  ID Q7PS33-5T76ND-MFKR5F-60VV03 failure

  Product ID: QE321UA #ABA

  Hard drive

  Hello:

  The failure of DST short is normally indicative of a hard drive that has failed and must be replaced.

  The operating system and the software can be reinstalled using recovery discs that you made or purchased from HP.

  In order to use the recovery disks, you need to replace the hard drive with one of the same storage capacity or more.

• Update Windows xp caused my computer blue screen and now will not start.

  Update Windows xp caused my computer blue screen and now will not start.  There has been no change to my system hardware or software otherwise.  After that windows update Setup, he asked to restart the computer.  When restarted, the computer screens and past blue to the quick menu for safe mode and last known configuration to work.  None of these mode of work, not to shelter or otherwise.  The only thing that he will now implementing market is quickly flashing the blue screen and restart once again to this quick menu.

  It's really annoying because I have important files on this computer work and can't afford to get in shape!   I put my confidence in using windows and keep it updated.   During the installation of your updates, it made my system fails and does not restart.   I'll be very upset if this update of windows xp causes me to have to reformat and lose important files!

  Any advice on a solution?   I need to get this computer work as soon as POSSIBLE.

  Ben River

  I ordered the Dell XP disc and did the re-install. It works fine now. The Dell technical support had me do some updates on the web as well. I have not had problems since. What happened with the automatic updates completely wiped out my operating system. At least I don't have to buy a new computer.

  If nothing else works, try reinstalling your operating system. It worked for me.

• Computer will not start normally - boots to the BIOS boot screen

  Hi, today I had problems on my computer and it will not start normally upward. This started happening today. When I turn on the monitor, the HP logo appears on a blue screen (as usual), but then, there are a lot of vertical white lines grouped perfectly on the screen (it's never happened before) he started to arrive yesterday. and when I try to start it, there is just a black screen for a long time and sometimes the system recov appears but it takes SO long to finish so I just stopped and went into safe mode and did a quick scans with Malwarebytes, MS Security Essentials and SUPERAntiSpyware, but they are all come clean except SUPER which came with a few things from tracking cookies...

  Today, I have scanned a full scan with malwarebytes and it says that there is no infection.

  can someone help me? I'm at the library atm! Thank you!

  Picture of the blue screen with lines here: http://img638.imageshack.us/img638/8583/post1278441253416372.jpg

  also - im wondering how to start with recov disks? I have two drives but only as on slot dvd thing and I know to start upward with her? should I boot with it because the layout is a little down? and I don't have an installation disc windows vista then Yes.

  Thank you very much!

  Hello Winston,

  According to the image that you posted, it seems that the blue screen is a blue screen with the HP logo on the subject.

  If this is the case, then the machine has not yet reached Windows and is suspended in the machine Power On Self Test.

  My recommendation for this scenario is to contact HP about what there is something at the level of the material / process/firmware BIOS which prevents the machine to get it to start Windows Vista.

  Let us know what they have to say.

  Best regards

  Matthew_Ha