E535 high battery drain when the laptop is turned off

Similar Questions

• Tecra A5 - charges the battery only when the computer is turned off

  Hello

  For a few days, my Tecra A5 has started to beep and stop it (like when the battery is low) then that it was connected to the power supply adapter.

  I finally realized that when the computer is plugged in, the battery discharge and does not use the power supply to recharge.

  On the other hand, if I turn off the computer, the battery starts to charge.
  I replaced the battery a few months ago, so I think it's still OK.

  The charger would be defective? Seems strange since it can always recharge the battery when the computer is turned off.

  Thanks in advance for your contributions.

  > The charger is defective?

  Theoretically; Yes, but could also be electronic supply on the motherboard is affected, but on the first stage of the AC adapter should be verified and laptop needs to be tested with AC adapter new, good work.

• Satellite P30 seems to completely charge the battery only when the unit is turned off completely

  Hi, I have my Toshiba Satellite p30 and only works on battery. This unit operate on sector or only on the battery as after the period of time go down the warning, then closes. The orange light fades in and out, but seems that it will only fully charge when the unit is turned off completely.

  I only just received this unit so bit of a novice.

  MASH

  Hello

  normally, the battery should always charge until it is full when the power is connected.
  If you have an orange light flashes, it means that something is wrong. Maybe your battery is faulty or something else. This should be checked by a technician.

  Good bye

• Wireless router WRT160N cable on the desk, I loose internet when the laptop is turned off.

  I have wrt160n v2 router wireless, it does not work for me.

  If my wireless XP laptop is only powered ON the Vista desktop internet wired connection works, I'm not wired or wireless using laptop computer, not on the internet, only power.

  If the laptop is turned off, I have no internet on the desktop, always connected via the router.

  The laptop is used and I didn't know if the without built-in thread was pretty new, so I bought a card to go in wireless.

  When everything is on everything is to play on the internet times two computers, but if you turn off the laptop I have to connect internet directly on the Office to continue in the internet.

  I started working with a tech support yesterday and they are difficult to understand. I had put in the new firmware and the problems persist.

  Can someone help me, I don't really have time to be on the phone for hours figure this all out.

  Thank you

  Jackie

  go to http://audipages.com/router/ and follow the instructions

• HP ENVY m4-1015dx Notebook PC: hp envy m4 battery not charging but fresh when the laptop is turned off

  Hello!

  I was with my hp envy m4 core i7 for quite a while now... recently, I formatted and installed windows 8.1 64-bit installed. I decided to download some drivers from the hp site and I realized I needed to provide my model of laptop model number I could not remember so I decided to remove the battery while the computer is still connected to the power for the number, then I went back to the battery. the latter, I realized that the cell had not accused beyond of 7%, which was the level of support, until I removed the battery and when I checked the charge level, it indicated that it was plugged in but does not support. When I tried to repeat the entire process as well as close the laptop, remove the battery and turning it again nothing work and completely refusing to charge for its on.when I decided to turn off completely and then it was off it perfectly complete accused 100% operating battery estimated more than six hours of charge time, guys help me to understand what might have developed and what will be the best solution.

  Hi @Phanz,

  Thank you for your inquiry.

  I entered which you have tried to download the driver on the HP website for your laptop but realized you need the model number.  You have removed the battery while the laptop is running.  Now when you reinstall the battery, it shows that it is connected but does not charge and continues to 7%.   You have repeated the process and close Notepad and removed and reinstalled battery, but there was no change. If you turn off it charges the battery to 100%.

  You did all your Windows updates?

  Have you tried the troubleshooter in Windows?

  First of all, I would like to try a Windows restore to before remove you the battery.

  HP computers - using the Microsoft System Restore (Windows 8)

  If restore doesn't work or is not possible, you could try a Refresh Your PC to solve problems (Windows 8).

  Then you can try the following steps.

  HP laptops - test and calibrate the battery (Windows 8)

  The battery method compatible ACPI Microsoft control is basically the driver that communicates between the computer and the battery. There is a chance that it became corrupt and bad reads the battery level.

  Step 1. Go to the Device Manager
  Step 2. Select the stacks
  Step 3. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 4. Click on uninstall
  Step 5. At the command prompt, put a checkmark in the box to remove the current driver
  Step 6. Shut down the computer

  Step 7: Remove the battery for a minute and then put new
  
  When the computer returns to the top it should automatically find the driver.
  
  Step 8. Go to the Device Manager
  Step 9. Select the stacks
  Step 10. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 11. Click "automatically search for an updated driver.

  Do the same thing with embedded controller compatible ACPI Microsoft.

  Last option is to reinstall your Windows 8.1 Pro.

  Good luck!

• Want to fire green W701 fingerprint reader when the laptop is turned off

  I realize the amount of electricity it uses is trivial, but unfortunately the accusation that carries the battery isn't much else. For the most part it's just because I don't have a use for the fingerprint reader. I completely uninstalled the software from the control panel. I thought that would get the light, but the "light on" survived the uninstaller not so complete.

  I hope that there is a way to do it in the bios. If necessary I could re-download the software of fingerprint and do a from there, if possible.

  It is possible to do anyway, please let me know. It's a minor thing, but I'm pretty annoyed that I'd make a sort.

  When you turn on the computer (off-state), press F1 when you see the Lenovo logo (until the BONES start to load). "I think that you should find the fingerprints under security settings). It shouldn't be too hard to find.

  Edit: Looks like that I don't remember it correctly. In the BIOS, you have the option to completely disable the fingerprint reader, but you do not have the option to turn off the green light only without disabling the fingerprint reader. If you want to disable the fingerprint reader completely turn off the computer, then turn on and press F1 when you see the Thinkpad logo (prior to the OS). When you enter BIOS click protection on the menu, and then select access to the Port of IO. In this list, you should have the ability to disable the fingerprint reader that I am sure that will also disable the go-ahead since the sensor is no longer in use. Press F10 to save and exit from BIOS.

  To remove the green light only, or disable the option to turn on your computer by sliding the finger without completely disabling the fingerprint reader, in my view, you must reinstall the fingerprint reader software. Then, you must open the application after installation and type your password or by the finger scan enter enter parameters. Then click the settings button in the toolbar and you should have several tabs where you can turn off the green light or disable the use of fingerprint predesktop authentication.

  -gan

• Satellite P10 - 802 - CD when the laptop is turned off?

  Hello

  Apparently, my laptop can read audio CDs while it is turned off using the audio buttons dedicated next to the cd player.

  He says in the presentation of the product and also the manual.
  I don't know how to do. can I just put it on a disk before you turn off the power (if not, I can't eject the disc)?

  Then I press play?

  Hello

  I think you should read carefully read the user manual, because you can find all the information on this subject in Chapter 4-8:

  If your computer is on or off, CD/DVD/audio control buttons are locked by default. To unlock, press the CD mode / digital for more than 3 seconds. Press the CD / Digital again for more than 3 seconds to block them again. When the CD mode / digital is unlocked, press CD mode / Digital and digital briefly to switch between the CD mode. The system LED status indicator will show you how you are.

  For more information see the user manual and if you n t have it you can download it on the Toshiba site.

  Welcome them

• E7440 latitude: Wake-on-Lan works when the laptop is turned off, but not when it's put into hibernation

  I have a Latitude E7440 running a clean install of Windows 10. If the computer has been stopped, I can use a Wake - On - Lan Magic Packet to the MAC address of the Ethernet port (as described here) to turn the computer back on. But if the computer is in hibernation, it does not work.

  Probably, it is that when the computer is in hibernation the link on my switch light is off, but when it is stopped, the link light is on.

  So my question is: How can I get this phone to maintain the LAN port when hibernation, in the same way on shutdown? Thanks in advance.

  smammy,

  Click on the link below for a possible resolution following on problem of your computer network settings.

  How do I enable Wake on Lan on Windows 10

• Re: Satellite M30X - battery won't charge unless the laptop is turned off!

  Hello

  I have a Satellite M30X who is about 4 years old and all of a sudden, she stopped electric network load when the laptop is turned on but strangely fees - although very slowly - when it is turned off.

  Any ideas please.

  Thanks for your help
  Amanda

  Hello

  If you want and if you can, then you could try to replace the battery to check if this problem is related to a dysfunction of the accumulator.
  I mean your battery is 4 years old and it wouldn't be nothing unusual if your battery does not work as it should.
  My battery is about 6 years old and 3 years may not be loaded correctly.

  But note that these are only suggestions and if you want to be 100% sure, you should ask a technician for a detailed notebook check.

  Concerning

• My reading shows the HDMI as a default device, but the sound is yet to come of the computer laptop, even when the volume is turned off on it

  Original title: HDMI sound

  I know that many have had problems, but I did not mine specifically. My HDMI connection was working fine with my laptop HP and m HD tv. I didn't use it for a while, now it is just the video, no audio on the TV. My reading shows the HDMI as a default device, but the sound is yet to come of the computer laptop, even when the volume is turned off on it. Ive read all the reviews and updates of pilot who was old. I don't know what else to do!

  Hello

  System Restore does not have this long period of time.

  You may want to refer to the suggestions in the thread below link and check.

  No sound via HDMI output portable computer connecting to TV

  I hope this helps.

• can I move all functions to another monitor and still close the laptop without turning off the second monitor on a laptop

  can I move all functions to another monitor and still close the laptop without turning off the second monitor on a laptop

  You define 'Action close lid' to the 'status quo' instead of sleep or Shut down:
  Go to-> double click "Power Options" Control Panel-> 'Select a power plan' under your selected plan, click "Change plan settings"-> "Change plan", click on the blue link 'Change advanced power'-> in 'Advanced settings' tab expand "power buttons and lid"-> extend the action of the 'close' lid, set "on battery" and "Plugged in" to "Do nothing"-> click apply-> OK button

  Multiple monitors: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/multiple-monitors-frequently-asked-questions

  Set up multiple monitors
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-multiple-monitors

  Move windows between multiple monitors
  http://Windows.Microsoft.com/en-us/Windows-Vista/move-Windows-between-multiple-monitors

  Understanding multiple monitors
  http://Windows.Microsoft.com/en-us/Windows-Vista/understanding-multiple-monitors

• Microsoft ON essential to keep all the time automatically, when the PC is turned OFF? I don't know to do.

  Dear Sir/Mam...

  I installed Microsoft essential to protect my notebook of virus & spy ware. When I turn off my laptop sound off automatically. Please send me the details to keep essential Microsoft on all the time, even my laptop is OFF please. Icon for turn on essential Microsoft whenever I start my computer. I can't find the related parameters in the ICONS.

  Once a computer is turned off, it's... Well well, off the coast.  But not just asleep, off.  By the definition of 'off' it does nothing.  Microsoft Security Essentials is a program and only works when the computer is turned on, as all of your other programs.  You cannot run a program when the computer is turned off.  The good news is that a computer is turned off is completely protected against malware are malicious software programs and does not work either.  There is absolutely no need to have anything by protecting your computer when it is turned off.  That said, I think that your concern doesn't really MSE all the time, but that's automatically done already when you turn on your laptop.  Not to worry.

  You see the pop-up warning that MSE has not yet started Microsoft.  If you click on the Start button in the pop - up notification MSE should start (but not immediately).  It may take a minute or two.  If you wait just MSE must start with itself and the notice will go away without having to do anything.

  I see the same thing when I run one of my virtual machines that you see when you start your laptop.  I'm very familiar with it.  It goes away in a few minutes and only means that from MSE wasn't the first thing the computer did when I turned on.  Windows moves to finally start MSE, but you can the long hurry up if you want.

  To manually start Microsoft Security Essentials, find its icon on the lower right side of your taskbar (called the "notification area").  The icon looks like a Red House with an X on it.  Right-click on the icon and choose open on the pop up list.  The MSE window opens on the desktop.  Click on "Start it now" button in the window that appears.  The window fades.  It may take a little time to start the MSE.  When everything is OK, home in the notification area icon will turn green with a check mark.

  When I see the Red House, I usually just give the computer a few minutes to complete marketing and the problem goes away on its own.  On rare occasions I start MSE myself.

  Colin Barnhorst

• My Ipad charger charge my iphone 5s only when the phone is turned off

  Hi guys. My Ipad charger charging my iphone 5s only when the phone is turned off. The phone does not recognize if it is on and I can't transfer files with it. Help, please?

  Hey Bigfootinyourface,

  I understand that you have a problem with your iPad charger or cable. Accessories and connectors uncertified can often result in the mentioned behavior. Article in the link below provides information that you may find useful.

  Identify the fakes or not certified lightning connector accessories
  https://support.Apple.com/en-us/HT204566

  See you soon!

• "due to an unidentified problem, windows cannot display windows firewall settings" fixed but still can not visit some sites and the laptop now turns off the coast on me. What should I do?

  I have an Apire one laptop with Windows xp service pace 3. I had to restore it to factory about 3 years ago. Some time after that the sound system began to slow and the Synaptics mouse stop working properly. I can move the pointer, but the left click does not work. It works in safe mode but not in normal windows. I used the Acer eRecovery for correct, but it did not work. I tried to download the driver for the mouse on the internet, but some how it could stop the download. I gave up at tring to fix. Some time in late March or early April, I couldn't access internet and after 22:30. I ran the diagnosis that is provided by internet explore and he said that the HTTP and HTTPS worked but the FTP did not work. AVG later told me my firewall is disabled and there was the possibility to reactivate it and I did. After internet explore stop allowing you to enter certain sites that I wanted to enter, I ran the Diagnostics again and he told me that a firewall client has been the cause of the problem. I tried to control my firewall setting, but had that "due to a problem not identified, windows cannot display the firewall settings". I thought AVG was the problem, so I have unintalled then he returned and attempted to access the firewall but got the same message. I typed in Google MySapce and found this site. I followed a few directions given to others in the thread started by joecarpenter33 and discovered that my firewall has been deleted and Base filtering engine has been deleted also. I downloaded and ran Malwarebytes ANti-Malware and SUPERAntiSpyware Free Edition and tdsskiller. MBAM has found a Trojan. The results of the analysis is less to:

  Malwarebytes Anti-Malware (Trial) 1.75.0.1300
  www.Malwarebytes.org

  Database version: v2013.04.10.14

  Windows XP Service Pack 3 x 86 NTFS (secure/setting network Mode)
  Internet Explorer 8.0.6001.18702
  Ziadie Berry: BERRY-LAPTOP [Director]

  Protection: disabled

  10/04/2013-17:44:54
  MBAM-log-2013-04-10 (17-44-54) .txt

  Scan type: quick scan
  Analyze the options enabled: memory | Startup | Registry | File system | Heuristic or Extra | Heuristics/Shuriken | PUPPY | PUM
  Analyze the options disabled: P2P
  Objects scanned: 271656
  Time elapsed: 43 minute (s), 42 second (s)

  The process of memory detected: 0
  (No malicious items detected)

  Modules of memory detected: 0
  (No malicious items detected)

  The registry keys detected: 0
  (No malicious items detected)

  The registry values detected: 0
  (No malicious items detected)

  Registry data items detected: 0
  (No malicious items detected)

  Files detected: 0
  (No malicious items detected)

  Files detected: 1
  C:\RECYCLER\S-1-5-21-4674304-3331980883-3375822000-500\$7832f44fdd2ba165f6ea01bec7f363fd\n (Trojan.0Access)-> quarantined and deleted successfully.

  (end)

  Malwarebytes Anti-Malware (Trial) 1.75.0.1300
  www.Malwarebytes.org

  Database version: v2013.04.10.14

  Windows XP Service Pack 3 x 86 NTFS
  Internet Explorer 8.0.6001.18702
  Ziadie Berry: BERRY-LAPTOP [Director]

  Protection: enabled

  10/04/2013 23:43:49
  MBAM-log-2013-04-10 (23-43-49) .txt

  Scan type: quick scan
  Analyze the options enabled: memory | Startup | Registry | File system | Heuristic or Extra | Heuristics/Shuriken | PUPPY | PUM
  Analyze the options disabled: P2P
  Objects scanned: 269636
  Elapsed time: 49 minute (s), 41 second (s)

  The process of memory detected: 0
  (No malicious items detected)

  Modules of memory detected: 0
  (No malicious items detected)

  The registry keys detected: 0
  (No malicious items detected)

  The registry values detected: 0
  (No malicious items detected)

  Registry data items detected: 0
  (No malicious items detected)

  Files detected: 0
  (No malicious items detected)

  Files detected: 1
  C:\WINDOWS\assembly\GAC\Desktop.ini (Rootkit.0access)-> quarantined and deleted successfully.

  (end)

  I ran the Diagnostics today after Internet explore and my other browsers stop allowing me to internet access. That's what came back:

  Diagnosis of last run time: 17/04/13 17:48:14 WinSock Diagnostic
  WinSock status

  attmpting error information to validate the Winsock base providers: 2
  error not all entries could be found in the basic services provider winsock catalog. A reboot is required.
  user redirection of information in support of the appeal

  Diagnosis of network adapter
  Network location detection

  Info to help home Internet connection
  Identification of network adapter

  Info network connection: name = Local, peripheral network connection = Realtek RTL8102E Family PCI - E Fast Ethernet NIC, MediaType = LAN, type = LAN
  Info network connection: name = wireless, peripheral network connection = Atheros AR5007EG Wireless Network Adapter, MediaType = LAN, type = Wireless
  Info both Ethernet connections and wireless available, ask the user for selection
  required user input action: select network connection
  Info Wireless connection selected
  State of the network adapter

  Info network connection status: connected

  HTTP, HTTPS, FTP Diagnostic
  HTTP, HTTPS, FTP connectivity

  WARN HTTPS: error 12029 connecting to www.microsoft.com: a connection with the server could not be established
  warn HTTP: error 12029 connecting to www.microsoft.com: a connection with the server could not be established
  warn HTTP: error 12029 connecting to www.hotmail.com: a connection with the server could not be established
  WARN HTTPS: error 12029 connecting to www.passport.net: a connection with the server could not be established
  WARN FTP (passive): error 12029 connecting to FTP.Microsoft.com: a connection with the server could not be established
  WARN FTP (active): error 12029 connecting to FTP.Microsoft.com: a connection with the server could not be established
  error could not make an HTTP connection.
  error could not make an HTTPS connection.
  error could not make an FTP connection.
   
  Still, he remains connected to the wirelesss connection, but won't let me access the internet. Right now I use a proxy to help, but access to the sites are limited.

  I used the tweaking software and my firewall is back but, I have yet to visit some sites and the laptop now turns off by itself.

  Hello

  Follow these methods.

  Method 1.

  Start the computer in safe mode with network and run a full scan of computer viruses.

  To start the computer in safe mode: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 2.

  If the steps above do not help, then try to scan the computer using Windows defender in offline mode and check if that helps.

  Search for spyware and other potentially unwanted software: http://windows.microsoft.com/en-US/windows7/Scan-for-spyware-and-other-potentially-unwanted-software

  What is Windows Defender Offline? : http://windows.microsoft.com/en-US/windows/what-is-windows-defender-offline

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 3.

  You can create a new user account and check. Once the new user account works fine, then copy the data from the old user account for the user account.

  How to copy data from a user profile damaged to a new profile in Windows XP: http://support.microsoft.com/kb/811151

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• The trash empties automatically when the computer is turned off. How can I fix it.

  The trash empties automatically when the computer is turned off.  How can I fix?

  The trash empties automatically when the computer is turned off.  How can I fix?

  Find what to do (something you installed and/or took the time and effort of installing) and undo - because it isn't Microsoft / default, or even something extremely simple (not something inadvertently, you can check, etc.) to (that happen.)