EA6300 SSID Broadcast

Similar Questions

• Disable the SSID broadcast

  I have a v1 WRT610N router and cannot find where I'm able to disable the SSID broadcast.  I thought I had looked at all the settings screens, but I can't.   can someone tell me how to disable the SSID broadcast for this router?  Thank you!

  Click on wireless on top and it should show these two things

  (On the red circles)

  

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Unable to connect via wireless with SSID broadcast disabled

  I want to configure my router for my SSID is not broadcast, because I think it's a logical step to take for increased security. I have not been able to do since I started using my new laptop Inspiron 5558. I tried this several times and every time I turn off the SSID broadcast, I am not able to connect to the Wi - Fi on this laptop. Other remote computers in my house and my smartphone connect without problem, but nothing I've tried helps my new computer Dell laptop to connect via Wi - Fi, except for allowing the SSID broadcast.

  I have a router Actiontec MI424WR reverend E. I have installed the new driver and the Intel PROset utility and unfortunately nothing has changed. I went to the settings to investigate some of the other solutions offers, and I came across something that seems to have solved my problem. What I found in SETTINGS/network & Internet/change adapter options/Wi-Fi/see the status of my properties of connection/Wireless / on the connection tab, it was an uncontrolled area with the words "connect even if the network is not broadcasting its name (SSID). I checked this box, and since then, I was able to connect to my network wireless with SSID broadcast disabled. I will now call this resolved and if no new problems arise. start a new post. Thanks for sticking with me on this.

  Ed J.

• SSID broadcast

  Want a couple of opinions on the broadcast of the SSID or not. We have 200 series 1200 ap on a University campus and currently distributed only in a few areas (5%) on campus we also have cisco WLSE to manage.

  In my humble OPINION, not broadcasting the SSID is security the same way that wrap you in aluminum foil you made the bulletproof. (It is not / is not, believe me).

  A large part of the decision boils down to bandwidth management.

  For example, do not broadcast your SSID, anyone using MS Windows Zero Config Wireless will have connection problems... ZWC always will prefer a SSID broadcast, often even if you have the client 'hard-coded' to associate with a specific SSID. Expect phone calls.

  Or the other decision, I hope that you have some solid backend authentication and authorization.

  It is essentially you have something other people want to (bandwidth, potentially free band). If you're lucky, people will * only * steal bandwidth.

  In the past, I think you will find that 'only' bandwidth theft is not enough, you will get some hotshot King or kiddie-script, or spammer, porn that will do malicious things in and on your network (if you are broadcasting your SSID or not.. Word bypass).

  Convenience for users and reduce the ' my laptop does not connect to your wireless system (it tries to connect to rogue AP from some students or other hotspot) calls. "

  Also keep them my mind is that if you don't broadcast your SSID, unlike someone else (malicious) (advertise * your * SSID)... they can usurp the user and capture traffic... or at least it makes it much easier to perform a man-in-the-middle attack (do a search for "ettercap").

  Advertise your SSID and have a good system of auth/auth on the back-end. Everything in the newspaper and be vigilant. Have a plan (and a strong policy) to deal with attackers and did not hesitate to run it.

  It is worth a few days of discussion, around this topic and a variety of opinions each valid in a given context. You must weigh the consumers against the administration, against the risk, compared to the budget... and a dozen other variables.

  (In general), there is no single best answer for most scenarios.

  That's why a good designer / architect system pulls down the fortunes and worth ever penny.

  Good luck

  Scott

• EA2700 disable SSID broadcast

  I am the latest firmware of the EA2700, but why I can not find it is turn off the broadcast SSID function?

  In the broadcast SSID router configuration is no longer an option in Linksys Smart Wi - Fi routers. Because there are different software for wifi analyzers, network whose SSID are hidden, yet be detected and seen by these software.

  Learn more why linksys decided to remove this option, please see this link:

  Title: where can I disable Broadcasting SSID in Linksys Smart Wi - Fi account?

  ID article: 25811

• Help: wet610n will not connect to wrt610n when the ssid broadcast is disabled

  I have a wet610n wirteless bridge linking very well with my router wrt610n broadcast ssid is enabled on the router, but when I turn it off then (the rest unchanged), the wet610n can not connect.

  What I am doing wrong?

  Or require the wet610n ssid will be broadcast (I didn't read that anywhere)?

  Thank you

  I have power cycled it, but I tried again and then experienced little more after you reset the wet610n and reconfiguring again.

  What seems to work, is to allow the broadcast of the SSID of the router and leaving the wet610n bridge wireless connection. So I can turn off the broadcast of the SSID and power cycle the wet610n and it can then connect.

  Without the first activation of SSID and connected, the bridge connects wireless.

  Thank you - it is "resolved".

• On remote access points SSID broadcast

  I'm deploying a Uniified Wireless Communication network that spans two location (Head Office and branch) using 1xWLC 4402 and 13 x 1252 APs. Is it possible to configure the access points to the branch to broadcast the ssid, which would not be released on the APs on the WLC seat.

  Thank you

  OLA

  Hi, you could use "overwrite WLAN' to do.

  Here the necessary instructions... to search "To substitute WLAN" in the document to get good paragraph...

  http://www.Cisco.com/en/us/docs/wireless/controller/4.0/Configuration/Guide/c40wlan.html#wp1089232

• AP1231G SSID broadcasts do not [config posted]

  I recently bought a set of access points AP1231G that have been pre-configured as root and nonroot bridges. Initially, I couldn't have a SSID will be displayed, thinking that I may have missed something that has been preconfigured I wiped the config and started from scratch. I went through several guides configuration to enable WPA with open authentication, but have had no success with the SSID is broadcast, and still less connecting to the AP.

  Any help is greatly appreciated. Config below:

  version 12.3
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host ap name
  !
  enable secret 5 $1$ lgoW$ zk7dfGkGLlZiOQuRFsxfV.
  !
  IP subnet zero
  !
  !
  No aaa new-model
  dot11 syslog
  !
  dot11 ssid MW2
  open authentication
  authentication wpa key management
  Comments-mode
  WPA - psk ascii 7 02050D4808090C285F4D06
  !
  !
  !
  username password Cisco 7 02250D 480809
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  encryption ciphers aes - ccm mode
  !
  SSID MW2
  !
  base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface BVI1
  IP 10.81.220.5 255.255.255.0
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  !
  output of the TFTP server
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end

  the antennas are connected?

  Concerning

  Surendra

• Cisco 5508 wlc mesh SSID broadcast?

  Hello

  I feel a strange phenomenon in my environment. Users on computers laptops Windows seem to be trying to connect to the SSID, they see the arrival of an access point which is mode bridge (and not broadcasting an SSID). I confirmed that nothing weird happens where the bridge would be broadcast SSID (standing right next to the newly imaged bridge on a laptop and when I connect I continue straight to a properly configured flexconnect AP).

  There is no output from the path of the box in Windows to tell the operating system that an access point is not valid once he thinks he is, so I'm reaching out to the community to see if someone else has seen this before. My next troubleshooting step is to bridges in stand-alone mode, if I can't find an answer.

  The environment consists of a WLC HA pair, standard 5508 flexconnect environment internal wireless, and we have a pair of bridge linking the two buildings. The affected computers are Windows 7 and Windows 8

  Hello

  Are you sure the mesh, access point is not configured to announce the WLAN of concern?

  Unless it is in a group of AP with no WLAN, WLAN 1-16 will be announced via its interface 2.4 ghz (and 5 GHz so "mesh access customer backhaul" is enabled).

  Here's a controller cli command to confirm (1550 is the AP name) ("site name" is the ap group)

  (jk-4400-111) > show ap WiFi 802. 11 b 1550

  Site Name........................................ 1550
  Site description...

  WLAN ID BSSID Interface
  -------         -----------        --------------------------
  18 management 88:f0:77:b7:b2:20
  management 88:F0:77:B7:B2:21 19

• WLC 2100 limit SSID Broadcast for each AP

  All,

  Is there a way to limit a certain AP to an individual SSID?  We have a WLC 2100 and 6 attached AP.  Let me know if you need more information.

  Thank you.

  Is there a way to limit a certain AP to one individual SSID?  We have a 2100 WLC and 6 AP's attached.  Let me know if you need anymore information.
  

  If you want, for instance, AP1 to broadcast the SSID, 1, 3 and 5.  AP2 to broadcast the SSID 2, etc.

  If this is the case, then AP groups is the way to go.

• Unique SSID broadcast to multiple AP

  Hi all

  How can we configure multiple Access Points in order to disseminate the same unique SSID?

  need to know the configuration...

  Thanks in advance.

  Here's a blog post I did on this very subject, virtual SSID

  http://www.my80211.com/home/2011/5/2/WLC-how-Cisco-virtualizes-the-base-radio-MAC-address-on-the.html

• WiFi does not connect if the SSID is not broadcast.

  I've updated to Sierra this afternoon. Everything seemed fine after the update. After dinner, my MacBook Pro (retina, 15 inches, beginning 2013) would not connect to Wifi. I reduced to a few things.

  It wouldn't connect the 5 GHz n If the SSID has been hidden. If I admitted the SSID to shown, it would connect without problems. It would connect to the 2 GHz band, even with the hidden SSID.

  I did the typical SMC reset and reset the NVRAM. I deleted the files related wifi and restarted the router and the MBP. I'm obviously on now and the speed seems normal with no dropouts. I can't hide the SSID now and will continue to work until he's asleep; No dice after that without reactivation SSID broadcast.

  Any thoughts?

  See you soon,.

  Fred

  With your same Apple ID, you can register for a free developer account and start a conversation with Apple engineers. They will answer your question: Bug Reporter https://bugreport.apple.com/

• WiFi does not work if the SSID is not broadcast by router

  I have a new 55HX929 and tried to connect to my wifi with its built-in wireless adapter. I do not broadcast my network SSID the router for security and privacy. The searched TV network, does not, and then it asks to enter the SSID. Then, it saves the information and trying to connect but fails. If I enable SSID broadcast on the router and then the tv connects fine but I don't have to do. My tivo with its usb wireless adapter works fine with the SSID broadcasts do not when I configure the network settings. On the same stand as the TV with the power of the signal fine. I am currently using a wireless connected to the ethernet jack TV bridge to work around the problem, but it's a waste when the tv should work with a standard network configuration.

  Reading sortiesdvd.com, people have the same problem with NX720 and Sony Google Internet tv. So it seems to be a common problem with Sony games.

  I tried online support chat, and they were not able to help. Everything they told me to do was reset the router and tv which does not help. I don't think they understood that a SSID came from how they responded to my questions.

  Can we get a fix for this?

  Thank you for your messages. We have forwarded your comments to Sony engineering for future updates.

• WLS-9163 is unable to reconnect in wireless mode after reboot in a WLAN with broadcasting SSID

  Initial configuration is defined by MAX using cable.  Wireless configuration is DHCP, with Infrastructure, WPA - PSK.  I save the settings and unplug the wired connection.  Then I delete the original instrument from the list of devices OR DAQmx of MAX.  Then I do a 'find network DAQmx Devices'.  The wireless device is discovered and works (self-test passes).  WLS link on the device indicator is green.

  Then, if I cycle power on the 9163, the WLS link never comes.

  This seems to be because my thread is not broadcasting an SSID.  If I go to a nearby access point and turn on the SSID broadcast, the WLS Link LED lights and MAX can review system.

  Is there a way to make the 9163 connect to a WLAN that don't broadcast a SSID?

  Burned - salvation

  First of all, thank you for the detailed notes. This helps a lot. You have the right version of DAQmx; now, we just need to upgrade the firmware. Here's how:

  After you have added the device in MAX (preferably on an Ethernet connection), click the button "Update Firmware":

  

  You will get a window that looks like this, where you can see what version of firmware you have. Click the folder to find the new firmware. It takes by default in a directory on your hard drive that contains the file 'ni9163fwROM.cfg' (if that's not listed for some reason, you can find it here: C:\Program Files\National Instruments\NI-DAQ\fpgafiles\mionetwork\ni9163)

  

  After the start of the update, you will look at a window of the scrollbar for a minute or two. Then, the device will be auotmatically reboot. You may need to reconfigure your settings after the update.

  Regarding the deletion/time that you did. You should not. After you have configured the wireless, you should see an IP address in MAX on the wireless tab. If she is not there, click "Refresh" now you can pull the Ethernet cable and continue to use the device. (If you want to convince yourself, click on the "Refresh" button again and you will see that the "Link Status" for the "Wired" connection is "down".)

  I hope this helps. Let us know what happens. Thank you