EA6500 - devices get weird IPs and DNS servers

Similar Questions

• Time Capsule has lost the Internet connection and DNS servers

  I use a Time Capsule for Time Machine via Ethernet backups for a couple of years, use it in mode bridge taking its Internet connection directly from my router and connected in turn by Ethernet to my iMac. (Most of the time that I also had wifi off on my iMac and took my Internet directly via the TC Ethernet connection.) A few months ago I upgraded to El Capitan, and the TC has lost its connection Internet (flashing yellow). A few days later I drove back to the Yosemite (for other reasons - Mail had gone mad) to restore a backup of the TC and everything was fine again for a few months. It may or may not be meaningful I plugged TC yesterday to new laptop for my wife to support for the first time, and this laptop is running El Capitan. Since then, the TC has once more lost its Internet connection and DNS settings and is stuck on flashing orange. By clicking on the 'Internet connection' status alert, tells me that the TC is not a valid IP address.

  

  I have reset the TC, repeatedly and reconfigured but all without success. After consulting the other discussions, I also tried giving the unit an alphanumeric name with no spaces & special characters and change the IPv6 "Link-local" configuration only, but this did not affect the result. And I updated the firmware for good measure. Then I unplugged overnight and carried out a full power cycle the steps recommended here, restart the router, TC and the computer (and performed a factory reset on the TC, while the router & computer was turned off). After doing that, the TC has become undetectable by AirPort Utility, until I have reset reconfigured once again, he and ended up in the same place.

  It may or may not be important to mention the following:

  1 when you set the TC after a reset, I repeatedly selected the option of adding to an existing network instead of create a network, but the installation wizard who ignored each time.

  2. in the installation each time, this point, I shows me the following, which seems to suggest that there is a problem but don't say so explicitly:

  

  I would be grateful for any advice.

  Weird how everything's going well for a few years and then crazy when you have something will change.

  El Capo adds some network problems more... but something could be fundamentally wrong with the installer.

  Your current configuration, it is apparently bridged but cannot get an IP address. The address 169.254 is give it since it's self generated.

  You need to do a manual installation. It simply means the Assistant is unable for any reason to be your network so start over and do it manually of misfortune (wow, or also possible misery, woah being where you are now!) to go...!

  1. I need to know what modem you are connected. Make and model please?

  2. the most important. What is the main router on your network or a modem?

  I gave the edge to make manual settings a few times. Somehow my instructions for Yosemite/El Capo got lost... I'll try and hunt down them. In the meantime, the basic method remains the same.

  https://discussions.Apple.com/thread/6509420

  It is not so difficult... You just know where you're going before you start.

  Airtport Utility cannot find airport Time Capsule on one of my Macs 2009

• In any case, to get space ESX and ESXI servers disk root partitions?

  I just wanted to see if there was a simple script I could run to check disk space on local servers - space not logic unit number. We had a situation where the root partition has been completed and caused a problem. I was wondering if there was a way to check using Powercli

  Cheers in advance!

  Have you ever had a glance at monitoring of the use of the ESX host storage (for example: / var/log) with PowerShell ?

  Condition that sudo is configured correctly on the ESX Server, it uses plink.exe to establish an SSH connection to the ESX Server and then executes a "df" for file systems and their size.

• Unable to set the IP address and the DNS servers manually

  I am running Windows 7 Professional 64-bit with SP1 on a Lenovo ThinkPad. The problem is that whenever I connect to my home LAN I can not put addresses IPv4 and DNS servers manually. Once I got close and open network and sharing Center option 'obtain an IP address automatically"is re-selected.

  I tried to set the IP address and DNS servers by entering the control panel command in administrator mode but the problem persists. The problem with the automatic configuration of IP addresses, is that my ISP DNS servers are slow, resulting in a slow internet. I also tried just setting DNS servers leaving windows automatically get IP addresses, but that did not too.
  I appreciate any ideas as to why this is happening and how ressemelable this question. Thanks in advance.

  Hello

  I suggest you to ask your question on the TechNet Forums, where we have some support professionals who are well equipped with knowledge on area issues, to do so please visit the link provided below.

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

• RVS4000 disabling IPS kills DNS

  Background: I recently bought a couple of routers RVS4000 put in place a VPN between my home and office. Initial setup went great and I got the VPN works with dynamic DNS at both ends quite easily. The only problem was that the performance sucked bad. my ISP gives me 45 MB/s and one see frequently in both directions of test of speed and SFTP on other servers sites, and they plan to upgrade our building at 100 Mb/s next month. With the RVS4000 in place I usually go down 12 MB/s in download and 7 Mbps. no problem, I thought. I read that most performance problems from the intrusion prevention have to look at each package. So I turned off the SPI...

  Problem: The problem I have is that if I turn off the IPS and DNS breaks on each computer on the network :-( Look-up go so slowly that my web browsers frequently time out. If I have somewhere access by IP address, then all is well and the flow of the router is acceptable (I see 28 MB/s, I actually managed to resolve the address of a speed test server). Unfortuantely this didn't do me much good if I do not have DNS. I restored the factory setting for a router and then carried out tests after each step of the configuration. Everything was fine until I turn off the IPS. I then restored to factory State, confirmed everything was fine and nothing else except the IPS; When I disabled it IPS DNS died once again!

  Question: Is there a work around for this? I pay for 100 M/s wiring between my home and office and with the active IPS I'm lose 90% of the performance. If I disable the IPS, the unit is essentially useless. Help! Any suggestion is welcome. If I can't solve this problem, soon the routers will have to return it for a refund.

  V 1.3.0.5 firmware is now available for download here: http://www.cisco.com/en/US/products/ps9928/index.html.

  Share your ideas.

  Thank you!

• Exit DNS servers

  Hi guys,.

  I am trying to list the DNS servers configured on each ESX host in the format below.

  ESX host

  -> DNS server

  -> DNS server

  ESX host

  -> DNS server

  -> DNS server

  That's what I have so far but I do not get the list of DNS servers, I get only one.

  $test2 = @)
  foreach ($v in ($vmh)) {}
  $details = "" | Select DNS name
  $VMHost = get-VMHost $v
  $details.name = $vmhost. Name
  $DS # = ($VMHost | get-VMHostNetwork) .dnsaddress
  ($vmhost | get-VMHostNetwork) .dnsaddress | {ForEach-Object
  $details. DNS = $_
  }
  $test2 += $details
  }
  $test2

  Thank you

  Dougie

  Try something like this

  foreach($esx in Get-VMHost){
      Write-Host $esx.Name
      $net = Get-VMHostNetwork -VMHost $esx    if($net.DnsAddress){
          $i = 1        $net.DnsAddress | %{
              Write-Host "`tDNS$i" $_            $i++        }
      }
  }
  

• Why is-36 of Firefox on Windows receiving connections from DNS servers? Option network.dns.get - ttl

  Following update Firefox 36, my firewall was flooding asking me to allow external connections from the Internet to my browser. Looking at it more closely, Comodo Firewall indicates that external websites are trying to connect to Firefox, port 53 to an arbitrary port on my machine.

  If I disable the option FF36 new network.dns.get - ttl, it stops. I can't find any documentation or help on this option.

  Why Firefox do this? Is Comodo incorrect when he labels it as an external connection attempt? (It has normally been extremely good to differentiate the incoming and outgoing traffic). I guess that Firefox is trying to determine the TTL for DNS caching, but it is not make sense why DNS servers then try to connect to me.

  I am reluctant to create a firewall rule to that arbitrary Internet connections on my machine are OK as long as their origin on port 53, tips on how to manage all that this new feature is firmly States would be appreciated.

  Thanks in advance for any help.

  Hi grammarye,

  Yes, you're right in thinking that Firefox is trying to find the TTL value. This is new in Firefox 36 behavior and was presented as services frequently changing DNS records (such as Cloudflare) were not working properly for Firefox users.

  Firefox makes asynchronous DNS searches - which means it will make a DNS query and then proceed to perform another task instead of waiting for an answer.

  Your ISP DNS server puts in cache only TTL an area for a short time, so if it does not the current LIFE expectancy, he will interview with other DNS servers to find.

  IANAE, but probably what is happening is:

  1. Firefox tries to find the DNS record for the domain that you want to connect to
  2. Your ISP DNS server does not have the current LIFE expectancy, then connects with other DNS servers to find
  3. During this time, Firefox lingers with something else
  4. DNS server, then reconnects to give you full DNS, including the TTL check
  5. Comodo sees the packets of the DNS server and panic

  I completely agree that arbitrary ports of white list is a bad idea, but in this case, the behavior is completely harmless.

  You can want to whitelist Firefox in your Comodo Firewall, or continue to let network.dns.get - disabled ttl.

  (edited to fix broken links and add a sentence)

• Im trying to open the tutorial of 23 minutes on how to use different tools in photoshop and it continues to come with unable to resolve the DNS servers worked fine yesterday? Ive had creative cloud on my laptop for a week and still have not been able t

  Im trying to open the tutorial of 23 minutes on how to use different tools in photoshop and it continues to come with unable to resolve the DNS servers worked fine yesterday? Ive had creative cloud on my laptop for a week and not yet able to get past the basics make me very frustrated.

  I guess you meant the links when you open photoshop CC. I tested all four videos of the 23 min tutorial and they all played fine. If something between you and adobe does not work correctly.

  • Check that your firewall is blocking the net. Try to access youtube videos and see if they play very well
  • Go to the adobe tv site and try to play one of the videos here. Adobe TV
  • If youtube plays very well and adobe tv does not work, next is to check if you have flash installed. Some videos require flash, others are html 5. Sorry that I could not confirm what player has been used for this tutorial. I think that html 5 but not sure.
  • Next is to look at the properties of your browser and check multimedia settings are not disabled if it y in a. (this is totally dependent on the browser)

  If none of this helps, let us know.

• PowerCLI Script to change the DNS servers and domain name

  Hello

  Brand new to PowerCLI, I'm trying to create a script that will change the domain name and the DNS servers of my ESXi servers. I found that I need to update the Vmware.Vim.HostDnsConfig to update these settings. I created the following script and the following error.

  $config = new-Object VMware.Vim.HostDnsConfig
  $config.domainName = "new.domain.com".
  $config.address = new-Object System.String [] (2)
  $config.address [0] = "10.69.69.80".
  $config.address [1] = "10.69.70.80".

  _this $ = get-view-Id "HostNetworkSystem-networkSystem.

  _this $. UpdateDnsConfig ($config)

  You can not call a method on a null value expression.
  

  Line: 1 char: 23
  

  + $_C. UpdateDnsConfig < < < < ($config)
  

  + CategoryInfo: InvalidOperation: (UpdateDnsConfig:String)], RuntimeException
  

  + FullyQualifiedErrorId: InvokeMethodOnNull

  I guessed the error message that I need to a value in the host name, I do not need to change the host name. So I create a variable to remove the host name and place it in the $config. Line received host name but still a mistake because the variable is pulling more information that I need.

  $hostname = get-VMHost | Select name

  $config. Hostname = $hostname

  When I insert the above code I have an error.

  Exception by calling 'UpdateDnsConfig' with '1' or the arguments: ' year error occurred during the configuration of the host.
  Line: 1 char: 23
  + $_C. UpdateDnsConfig < < < < ($config)
  + CategoryInfo: NotSpecified: (:)) [], MethodInvocationException)
  + FullyQualifiedErrorId: DotNetMethodException

  When I look at the $config I see the following.

  DHCP: false
  VirtualNicDevice:
  HostName: @{Name = ESXI01}
  Domain name: new.domain.com
  Address: {10.69.69.80, 10.69.70.80}
  SearchDomain:
  DynamicType:
  DynamicProperty:

  Of course the @{Name = ESXI01} will not work. Someone can explain how to get a host name in a variable and pass it to the Config.Hostname?
  

  You should be able to do easily by using the command "set-vmhostnetwork.

  I don't think that you can just write to VMWare.Vim.HostDnsConfig.

• Is "PXE - MOF: PXE ROM. exit" then below I don't get, "No Bootable Device - Insert Boot Disk and press any key any" why?

  I bought the lifetime windows, defender security system, I also downloaded the windows repair and ran it, I even cleaned my c drive and defragmented, but I always get the same black screen. This is what it looks like.

  PXE - MOF: Exit PXE ROM.

  No boot device - insert boot disk and press any key

  /} In this area here, I slash turns clockwise

  Does anyone know how planned it and most importantly, how to prevent?

  Try to change your startup settings for...

  1 CD-ROM
  2 USB
  3. HARD DRIVE
  4. (if available) floppy drive
  5 LAN.
  You can change it by pressing the button shown next to "Boot Order"

• I try to go to the website of tomtom and I get an error message DNS-cannot find server.

  I try to go to the website of tomtom and I get an error message DNS-cannot find server.  I tried the computer desktop and laptop and do not know what the problem is. I thought it was the Web site, but I could put my internet work top. Help, please.

  How your internet connection are connected, if you use Proxy, then try to uncheck bypass for local addresses...

  If you use a direct connection without proxy, even try to open in another browser, firefox IE, if its opening try to update the browser to your desktop computer.

  Thank you & best regards

  Alex k

• How to set an IP address manually and manual DNS servers for my printer HP Photosmart 7525?

  Cannot print.  EU of evil when the printer was initially put in place.  "Happytohelp01" Assstance solved the advised me; a manual IP address unBalayage DNS servers for the printer.  I did not write the information and now my printer is not working (it only worked for about a month), now nada.  I've had at the start of the connection to the web server problems - now its doing the same thing, but I don't know what IP Address and DNS to use.  Please help if you can.

  Hi @LaceyNo1,

  Welcome to the HP Forums!

  I understand that you are wondering, how to set an IP address manually and manual DNS servers for your printer HP Photosmart 7525. I am pleased to see that for you!

  After some research, I think I found the post, my colleague @happytohelp01, helped you with. In this post, Re: Photosmart 7525.

  Hope this is what you are looking for and have a good day!

• When I select this option I get the dialog box 'Create image s system' but it cannot find any 'backup devices on this computer"and lists the error 0 x 81000036

  Error image system original title: windows 7 0 x 81000036

  I'm doing a backup system image.  When I select this option I get the dialog box 'Create image s system' but it cannot find any 'backup devices on this computer"and lists the error 0 x 81000036.

  I have an ESATA connection on my Dell laptop I was trying to make the image on.  I use the unit every day to save files and which works very well.  He just leaves me CCADE with the system image backup...

  any ideas?

  Hello

  ·         You have created a system image backup before that?

  ·         You did it changes on your computer?

  ·         Is your esata formatted NTFS drive?

  Try to save the image of the boot system: http://support.microsoft.com/kb/929135

  Note: make sure that you start the computer in normal mode after a repair.

  See also the linkfor more information about the backup: http://windows.microsoft.com/en-US/windows7/Back-up-your-programs-system-settings-and-files

• Try to install Windows 7 via USB, El Capitan, Macbook Pro 2011 but get this error "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  I am trying to install Windows 7 via USB, (El Capitan, Macbook Pro - early 2011), but this mistake "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  You cannot use a USB on Mac 2011 Installer. Please burn the ISO on a physical DVD Windows (a DVD - R Carbon SL on the rate of burning slower is better) and use it to install Windows. The file Info.plist changes only allowing the creation of USB, but does not fully support a USB Installation.

• When I try and send a file to my laptop I get this error: "bluetooth device not found please make sure that your bluetooth device is propably connected and turned on."

  original title: BLUETOOTH PROBLEM Please HELP!

  When I try to send a file from my computer to my cell phone an error message appears saying "bluetooth device not found".

  Make sure that your bluetooth device is propably connected and turned on. »

  In addition, the mobile is unable to send any file to computer th.

  I've already matched the mobile with the computer and I use windows 7 please help.

  
  

   

  When I try to send a file from my computer to my cell phone an error message appears saying "bluetooth device not found".

  Make sure that your bluetooth device is propably connected and turned on. »

  In addition, the mobile is unable to send any file to computer th.

  I've already matched the mobile with the computer and I use windows 7 please help.

  
  

  Hey xtheultimatethinkerx

  Here is the vista forums

  Try the repost in Forum windows 7 the link below

  http://answers.Microsoft.com/en-us/Windows/default.aspx#tab=2

  Answers by topic

  • Office & Customization
  • Files, folders, & search
  • Game
  • Hardware drivers &
  • Install, upgrade, and activate
  • Internet Explorer
  • Music & Sound
  • Networking, mail, electronic, & updated online
  • Maintenance & performance
  • Photos & Video
  • Programs
  • Security, privacy, and user accounts
  • System repair & recovery
  • TV and movies on Windows
  • Windows Update

  Walter, the time zone traveller