EA6500 multiple IP addresses on the Internet interface

I have verizon fios business with 5 static IP addresses and am set up for ethernet wan. I can use EA6500 as the router instead of use the own router to Verizon, but I can't understand how to assign every 5 static IP on the internet interface addresses. I have already affected the first IP address in the Web interface, but don't see a way to add multiple IP addresses internet interface or NAT section where I can create static NAT.

Is it still possible with EA6500? If so, how?

I don't think it's possible, given that the router support 1 address static IP at a time.

Tags: Linksys Routers

Similar Questions

  • Can a VPN 3005 cause multiple IP addresses on the external interface?

    Nice day

    Can a VPN 3005 cause several IPS on an external interface?

    I expect to use it in an environment that has 2 ADSL connections to an internet service provider. For the sake of the exercise, we could call them ROUTER1 and ROUTER2.

    We have a few VPN we always want to spend by ROUTER1 and some VPN we always want going through ROUTER2.

    Is this possible?

    Thank you very much

    No, not possible, sorry.

  • Change the IP address of the external Interface

    I need to change the IP address of the external interface remotely.  I have SSH in to the ASA plan and make a change.  I can't be there to make this change, since the site is out of State.  There will be problems?  The current configuration is

    interface Ethernet0/0
    nameif outside
    security-level 0
    IP 66.102.7.22 255.255.255.248

    The new IP address will be 66.102.7.18 255.255.255.248.  Also, is this the right syntax?

    interface Ethernet 0/0

    no address ip 66.102.7.22 255.255.255.248

    IP 66.102.7.18 255.255.255.248

    Thank you.

    Diane

    Diane,

    If you access the ASA via its public IP address on the external interface, and if you change this IP address, you will lose communication with the ASA.

    It's better if you can make the change from the inside.

    If you need to change remotely, you can change the IP address, and then try the SSH connection to the new IP address.

    However if a problem occurs, you cannot access the ASA.

    The syntax is correct.

    Federico.

  • address of the loopback interface or sencondary in ASA

    I have a problem with Server Load balancing feature for firewall load balancing. If want to achieve this, we create an address of the loopback interface or secondary ip address in TWO firewalls (ASA). using hurried SLB mode... Can anyone suggest how this can be accomplished.

    Loopback interface cannot be configured on SAA. For load balancing on refer to the URL

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805fda25.shtml

  • VPN client with counterpart on secondary ip address on the public interface of the router

    Hello

    On our office LAN, we have a Linux server than it hosting a VPN connection to a remote client.

    Do this to ISAKMP card on our Cisco router port connections to the internal ip address of the Linux host.

    However, we now want to allow our users to establish VPN connections to our local network using the unit of Cisco VPN Client.

    Of course, this would present challenges, as the ISAKMP our router port is mapped through an internal host.

    So, we tried to set up a secondary ip address on the router and VPN clients to connect to that.

    What we see in our newspapers is as follows:

    Phase 1 is very well established, and the VPN Client prompts the user for a user name and password.

    Authentication of the phase 2 starts, but the router says it's is not to receive a proposal of hash of the client.

    185 12:18:06.943 09/03/11 Sev = Info/4 IKE / 0 x 63000014
    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

    (in this case, where x.x.x.x is the secondary ip address on the public interface)

    After that, the Phase 1 SA is removed and the connection fails.

    My understanding is that the Phase 2 negotiation takes place with the ip address assigned to the client in Phase 1, which suggests that the problem occurs because the client communicates with the main on the interface ip address, and no secondary ip address.

    When remove us the mapping of port isakmp and the VPN client to connect to the primary ip address, everything works fine.

    Question:

    It is possible to establish 2 router VPN Client uses a secondary ip address?

    If not, is there some way I can implement the port mapping so that it occurs, the connection comes from a specific ip address?

    Garreth

    Should be supported on IOS.

    The command is crypto ctcp port...

    Check this link:

    http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6635/ps6659/prod_white_paper0900aecd8061e2b3.html

    Federico.

  • MULTIPLE ADDRESSES ON THE EXTERNAL INTERFACE IP

    Hi all

    We put in place a number of ASAs for use with corporate VPN. When remote users connect using anyconnect they can hairpin on the Internet from Headquarters and must assign a public IP address for this purpose. To avoid people getting the same public address every time they go to the internet, we want to set up a pool of public addresses which will be awarded at random to the user of the VPN. Also, for their incoming connection requests, we have a ddns that solves a unique ip address for incoming connections. So, in summary clients connect to a single IP address on our ASAs, then hairpin at the internet and receive a public IP address from a pool. Look at us a few options to do so, but would appreciate any suggestions as to how best to achieve this goal.

    Thank you

    Hello

    It seems to me that the order of the chosen one NAT IP address of the NAT pool is random. I tested on my home with a pool of public addresses small ASA5505.

    I don't know if there is difference between different levels of Software ASA or rather the NAT configuration format. Since the 8.2 (and below) and 8.3 format (and more recent) is completely different.

    If we guess you configure NAT pool for VPN Client users connected to the ASA then configurations need you so

    Software of 8.3 and above

    permit same-security-traffic intra-interface

    object-group, network VPN-POOL

    Description the user VPN address Pools

    object-network 10.10.10.0 255.255.255.128

    object-network 10.10.20.0 255.255.255.128

    network of the PUBLIC-POOL object

    1.1.1.1 range 1.1.1.254

    interface of VPN-POOL PUBLIC POOL dynamic NAT (outside, outside) after auto source

    8.2 software and below

    permit same-security-traffic intra-interface

    NAT (outside) 200 10.10.10.0 255.255.255.0

    NAT (outside) 200 10.10.20.0 255.255.255.0

    Global 1.1.1.1 - 1.1.1.254 200 (outside)

    Global 200 (external) interface

    I don't know what is the amount of your user, but I guess you don't such a pool of important public addresses for users. The configurations above also contain a dynamic PAT when the NAT pool runs out.

    Is that what you're looking for?

    Hope this helps

    -Jouni

  • Cannot access a Web site, but can ping IP addresses on the internet

    -With the help of Vista SP2 64-bit on laptop faulty.

    -Number of computers on the same network have access to the internet.

    -Tried several network interfaces on this laptop, but no luck for access to the network, wired or wireless

    -From this notebook, I can ping addresses Internet IP so the problem seems to be the side DNS.

    -Flushing DNS cache and reset the network interface.

    -Rebooted several times.

    What did I miss?

    Thanks in advance

    Hey easternguy,.

    Check if you can test the Web site by name.

    To do this:

    a. Click Start and type cmd.

    b. press ENTER.

    c. type the following command:

    ping hostname

    Ping uses name resolution to resolve a computer by IP address name. Therefore, if you successfully ping the IP address but you cannot ping a computer name, there is a problem with host name resolution, and no network connectivity.

    Case 1: If you can not ping the Web site using its address, follow these steps.

    In this case, try changing your host file.

    In the C:\Windows\System32\Drivers\etc Hosts files may be damaged or corrupted.

    Review the contents of your HOSTS file and compare it to the screenshot below. There is no need to worry about any line that starts with a # is ignored by Windows. In addition, the line "127.0.0.1 localhost" can be ignored without risk, because it is a standard input.

    Everything that appears in your HOSTS file without a # earlier this year, aside from the "127.0.0.1 localhost" line, should be regarded with suspicion when we try to diagnose the cause of the problem. The fastest way to test the involvement of HOSTS file is to just rename the host file. By changing the name of the HOSTS file, prevent us Internet Explorer to use it and so all problems caused by the file.

    Case 2:

    If you can ping external websites by IP address and name, but can't browse the web, probably your browser is misconfigured.

    Check that you do not have an incorrect Proxy Server affected necessary or not.

    For Internet Explorer, follow these steps.

    a. open Internet Explorer.

    b. go to Tools / Internet Options.

    c. click on the Connections tab.

    d. click the LAN Settings button.

    "e. uncheck both" "automatically detect settings" and "use a proxy server for your LAN '.

    This should be it.

    Kind regards

    Shinmila H - Microsoft Support

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Best practices ACL - on the Internet interface

    I have a question relating to the ACL on an interface oriented routers 'Internet '.

    After reading several whitepapers on the subject, an ACL recommended would typically contain the following instructions.

    In addition, the Cisco SDM automatically generates an ACL externally similar face:

    IP extended INBOUND access list

    permit any any icmp echo

    permit any any icmp echo response

    allow all all unreachable icmp

    deny ip 10.0.0.0 0.255.255.255 everything

    deny ip 172.16.0.0 0.15.255.255 all

    deny ip 192.168.0.0 0.0.255.255 everything

    deny ip 127.0.0.0 0.255.255.255 everything

    refuse the host ip 0.0.0.0 everything

    refuse an entire ip

    !

    So my question is...

    What is the point of lines 4-8 during the last line blocking them anyway?

    I understand that when we discover the ACL there's the number of matches by explicit ACL entry, but in terms of blocking, I don't see the advantage.

    Instead, the following ACL would provide the same benefit and be easier to maintain.

    IP extended INBOUND access list

    permit any any icmp echo

    permit any any icmp echo response

    allow all all unreachable icmp

    refuse an entire ip

    !

    Am I missing something obvious?

    Thanks in advance for the help,

    Kind regards.

    Hello Peter,.

    I believe that when people post these examples, they assume you will put additional instructions forward the "deny ip any any" at the end. There are really a few rules that you must use when you create an Internet facing ACL:

    1 deny incoming traffic from your IP addresses registered to prevent identity theft.

    2 refuse incoming Microsoft LAN traffic (port 445, 137-139, etc)-any legitimate Microsoft LAN traffic should be limited to a VPN.

    3 deny traffic from private addresses or null.

    I'm sure that you realize that packages can be made with the ILO established is enabled and use private addresses (broadcast or unicast) or your addresses as a source to create the undesirable traffic or denial of service attacks. That's why these statements are called separately. You would use before the "permit tcp everything (recorded your IP range), set up" statement.

    Your ACL proposed only allows tcp responses to queries generated internally. Unless you really don't want any UDP traffic, you must include a reflexive access list statement to allow the UDP. I hope also that you have a big server log or only a few hosts on your network - check all tcp traffic will take a little space!

  • the IP address of the MGT network used in the interface of BVI1

    We strive to implement the autonomous AP using mgt address in the BVI1 interface, but without success.

    Would appreciate another set of eyes looking at it.

    The client authenticates with server radius very well but no IP address is assigned to the customer.

    pass us the IP helper on our IVR L3 address for vlan 57 and vlan 54 the vlan mgt.

    All our other standalones have the ip address of BVI1 in the same vlan as the VLAN of the customer.

    The config is attached.

    The switch for the port configuration is the following:

    interface GigabitEthernet0/45
    switchport trunk encapsulation dot1q
    switchport trunk vlan native 54
    switchport trunk allowed vlan 54,56,57,103,106
    switchport mode trunk
    events-the link status logging
    inline static power

    VLAN 54 is the vlan mgt in use for all other devices. We just never tried to use it for AP before this attempt.

    You can also add this command:

     interface Dot11Radio0.54 encapsulation dot1Q 54

    See the configuration guide for basic here:

    http://rscciew.WordPress.com/2014/05/24/multiple-SSID-configurations-on-...

    http://mrncciew.com/2013/11/14/autonomous-AP-with-external-RADIUS/

    Concerning

    Remember messages useful rates

  • Unable to connect to the internet. PC a firewall via ethernet. "no isp address.

    I have windows xp on my pc. I can't connect to the internet it tells me that I am a firewall via ethernet. and I did not have an Internet service provider address and the address of the Internet service provider on my computer laptop girls is different. my ISP told me that I need to download and install something out of microsoft will fix my problem automaticily. I know not what I'm supposed to download and not more than my provider of the Internet service provider. can anyone help.

    Hi angieb9171,

    · Provide you receive the exact error message.

    · Who is the provider of Internet services on the computer?

    · When was the last time you were able to connect to the internet?

    · What type of internet connection do you use?

    · You have security software installed on the computer

    Follow the methods below to hone in on the question:

    Method 1:

    The security software installed on the computer may block access to the internet on the computer.

    If you have any third-party security software installed on the computer, turn it off and check if it works.

    Important: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

    Method 2:

    Follow the steps in the below link: how to troubleshoot possible causes of Internet connection problems in Windows XP:http://support.microsoft.com/kb/314095

    See also: the problems of Internet connection:http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-Internet-connection-problems

    With regard to:

    Samhrutha G S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • How Internet IP address with the Linksys BEFSX41 router pings?

    Hello.

    Does anyone know how to let my Internet IP address responding to pings from the outside with this model of router? I can't seem to find the option to set (the configurations of way more than my old Netgear RT311). I couldn't find it via Google search (all internal pings). I use the 1.52.15 firmware version.

    Thank you in advance.

    See the demo of the UI here. Change the option "Block anonymous Internet requests" for people with reduced mobility. Then the router will respond to the pings on the ip address. If this does not work once you change it, check that the BEF was really a public IP address on the internet port. Check the status page it shows what IP address the router uses on the internet port.

  • SSL VPN IP address other than the IP address of the interface?

    Hi,

    Is it possibe to use a differnt IP Address from the same Subnet of OUTSIDE
    INTERFACE? Instead of Interface IP Address itself. The Idea behind is,
    Clients should not use OUTSIDE Interface IP Address for SSL VPN, but whereas they can
    use from the IP Address Pool of OUTSIDE Interface.

    Regards

    Brassart Abbas

    If SSL is completed on an ASA firewall, you can finish it on all other ip addresses but the external interface.

    If it is completed on a router IOS, Yes, you can use a different ip address to put an end to the SSL VPN connection.

    Hope that answers your question.

  • Network for access to the external interface inside

    Hey,.

    I have an ASA5520 7.2 (1) I have a few probs with - which is something I struggle with that.

    I'm trying to hit a website of a host on the inside network that is actually hosted internally, but decides the static NAT would focus on the external interface of the firewall.

    Now I can see the TCP built, translation occurring at a port on the external interface, this port high dialogue to one of the static electricity would be addresses on the external interface, then that's all. There are no more entries in my journal in regards to the connection and I get not syn on the internal web server is so the connection is not back in.

    IP address outside 222.x.x.9 255.255.255.248

    IP address inside 192.168.87.1 255.255.255.0

    Static NAT to Web servers: -.

    public static 222.x.x.10 (Interior, exterior) 192.168.87.5

    access lists access... :-

    list of allowed inbound tcp extended access any host 192.168.87.5 eq http

    Access-group interface incoming outside in

    Everything works fine when creating a global internet address - just not when address from inside and dynamic PAT is performed to the original address.

    Here's a capture session by using the following access to capture list inside and outside interfaces simultaneously

    permit for line of web access-list 1 scope ip host 222.222.222.10 all

    web access-list extended 2 line ip allow any host 222.222.222.10

    on the INSIDE interface (nothing is connected to the outside) (ip addresses have been replaced by nonsense) - but address 222 is would take into account the interface static and the other is on the internal network.

    316: 19:14:02.900206 192.168.87.10.2275 > 222.222.222.10.80: S 2029971541:2029971541 (0) win 64512

    317: 19:14:05.973185 192.168.87.10.2275 > 222.222.222.10.80: S 2029971541:2029971541 (0) win 64512

    192.168.87.10 is my client is trying to connect

    Someone of any witch hunt, which is stop this function work?

    All networks are directly attached and there is no route summary ancestral anywhere.

    I hope you guys can help!

    Concerning

    Paul.

    To my knowledge the ASA supports only hairpining on a VPN tunnel. The security apparatus does not allow traffic that is sent to an interface to go back in the direction of what she received.

  • Share USB over the internet using the E3000

    I just bought an E3000 router, everything started installation and configuration USB share for my network. But how to share this USB on the Internet with the family etc. ??? I keep searching and searching and just can't find the answer. It's the ONLY reason I bought this specific model.

    You are able to share the drive within the network?

    Open the router configuration page and go to storage tab, click Activate the FTP server FTP server void tab and enable access to the Internet.

    Now, go to the status tab and check the IP address of the Internet on the status page. Note the Internet IP address. Consider the Internet IP address X.X.X.X. . Open the Internet browser and in the address bar, type ftp://X.X.X.X .

  • WLC - slot configuration of the dynamic Interface DHCP settings

    Hi guys,.

    If I have a dynamic interface that is connected to a subnet where the router interfaces have DHCP servers configured under the orders of support address, do I need to configure the DHCP fields in the dynamic interface configuration?

    I have the support address configured on routers connected AND these fields configured with the same DHCP servers.

    I was wondering if I can take the IP address of the configuration of WLC?

    Thx a lot indeed.

    Ken

    Ken, the DHCP address in the dynamic interface, is the address the WLC is unicast the DHCP request when a client tries to use this interface. In normal operation, this address is needed. Is there a way to get the WLC to fill the package to the wire to make it a show instead of a unicast packet. CLI command is dhcp proxy disable config.

    But I think that even if you issue the CLI command, the software wants the DHCP address in the dynamic interface.

    HTH,

    Steve

Maybe you are looking for