EA6500 (v1) constantly reboots with the new Firmware (1.1.29)

The latest firmware available (Build 162351) Ver.1.1.29 for my EA6500 (v1) is very unstable, and I had to roll back to 1.1.28 (Build 146072).

This occurs when the two bands of wireless network are enabled. The router works for 5-10 minutes (sometimes even shorter) and restart only randomly.

When wireless networks are disabled, it is pretty solid as a rock.

Roll back to 1.1.28 solves this problem, if at least I can have functioning wireless networks.

It would still be nice to be able to use the latest and best however. As long as I would be able to access the router using my Tablet and IE11.

Has anyone seen similar behavior? If so, advice?

Thank you



How did you get the update? The proposed method is to:

Perform a factory reset

Flash the firmware manually after uploading to a pc cable

do a factory reset

make the config from scratch, not from a restore

The second Reset clears any old stuff on the router and solves some problems such as you saw.

Tags: Linksys Routers

Similar Questions

  • Recognition of devices with the new firmware on EA3500

    Under devices, I find that my laptop Apple (WIFI connection) and our Dell Desktop (LAN) connection are considered to be the same device.  The operating system shows the EA3500 of this device is the system connections apple IOS and address numbers displayed in this device.  It is therefore impossible to set parental control separately on each computer.  What could I do to get the EA3500 to recognize these separate devices?  I tried to force Apple WIFI network address to another address.  All that happened was the address of device updated on the list of EA3500 devices, but LAN and WIFI addresses remain together in the same device name and MAC OS on the list of devices.

    I have the latest firmware downloaded on my EA3500.  It wasn't a question previously when I ran the old firmware.

    Here is one that I see in the list display the LAN address for the address of Dell and WIFI for Apple on the same devices screen.  When I turn off a device, the respective entry goes.  Only when both computers are turned off reflects the unique device entry on the EA3500 offline.

    Details of the device:

    Name: Macbook Pro laptop

    Manufacturer: Apple

    Model: MacBook


    IP (LAN)-1:

    MAC address: XX (does not list address voluntarily)

    -2 (wireless) IP address:

    MAC address: XX (does not list address voluntarily)

    I couldn't get the a screenshot as assignment would fail.

    This is a bug that comes and goes. Personally, I didn't for a while. But it's still there (even with the latest firmware)... If you catch this bug, it is usually difficult to shake because it can resurface. It affects too EA4500.

    There is no real rhyme or reason why it appears.


  • Problems with the new firmware 0.1.E.1.4


    After the last update, my phone (Samsung Galaxy S3) has problems with his phone for headset support.

    I can only use the headset as headphones to phone for calls. Do not go with general audio profile.

    Sometimes I can connect audio but it disconnects quickly.

    It is a very serious problem that needs to be fixed, but I doubt that Sony will be releasing a fix quickly.

    So, how do I go back to the previous firmware? (0.1.D.0.6)

    With this firmware, I had no problem. The new firmware has a significant improvement as long as Visual but the helmet doesn't help...

    I need help. Thank you.

    OK, I just do a downgrade.

    I did a factory Reset on the helmet, downloaded "Update Services" and the program tells me that there is an update available, after the update has been completed I'm back on 0.1.D.0.6!

  • Problems with the new firmware

    New firmware called my books podcasts and mixed together books and podcasts.  Podcast alley section. Also fails to player.  Firmware has screwed my player. Need help please, I have a sanDisk Sanasa fuse + MP3 player and latest firm ware (today).  Thanks in advance.

    The first time that you access the books, it's confusing, but take a look on all small three points at the bottom of the screen after you type the central point.  This reveals that there are three screens partitions via slide to right or left on the touch screen.

    To navigate between the choices, some books with a single tap Center, then sweep right or left to go between Audible / books / Podcasts.

    Do you like the new LOCK feature?

    I just made the connection, your name reminds me of Benjamin Vandervoort, played by John Wayne, in The Longest Day.  He served with distinction in Holy Mother Church.


  • Having problems with the new firmware, how do I go back?

    I use my rocket to play 'learn the french' CD with very short (2 minutes) titles.  I am constantly jump back securities to repeat what they said.  Unfortunately, the "back to the previous track" button doesn't seem to work right now audio books, and I would try to go back to the old firmware to see if it's the "rocket" or something in how I ripped and my tag CD.  (the track numbers are there, so I think it's the firmware).

    How to get back?

    Thank you!

    Manually install 1.02.26

  • Can no long use transfer to SD card with the new firmware update 23.0.1.A.3.12

    I just received the last update for my Z2. My camera now has a 23.0.1.A.3.12 firmware.

    I encountered a problem. Can I transfer is more pictures on SD card through transfer to SD card as storage.

    I would like to consider making a repair of the system as this will often fix problems after an upgrade – it will be factory reset your phone

    Turn off your phone and unplug the PC (Hold to increase the volume and power for 10 seconds)
    Start PC Companion and select the area of support then updated my phone/Tablet then blue fix my phone/Tablet and follow the instructions on the screen - when you are prompted, always connect your phone off press and hold volume or back button - this should begin the process of repair or reformatting

    If you use Windows 8/8.1 or a 64-bit operating system and then adjust the settings for PC Companion and run in compatibility mode and choose Windows 7 or XP

  • EA6500: What changes or improvements of the new Firmware offer?

    I just connected to two of my three routers EA6500 and noticed that they have new firmware: This new version gives anything of note... or... did some minor changes?

    See the release notes for the update here:


  • Sierra not coordinated with the new version of the iMac

    After reading what hoops I have to jump if for my 8 year old Mac Pro 4.1 to run Sierra, I wonder why launch the Sierra was not coordinated more closely with the new Apple Desktop launch (s).

    I read that this iMac 27 "5K is the best choice to replace my Mac Pro for graphics and video. Is my correct info and what is the new one be released? A small idea.

    Can your Mac Pro4, 1 switch to the Sierra if you update your Mac Pro 4.1 for Mac Pro5, 1 one EFI firmware.

    On the updates of the EFI and SMC firmware for Mac computers with processor Intel - Apple Support

  • Updated my iPad with the new OS.

    Updated my iPad with the new OS. Initially it lights, so I have two buttons held together and finally happened. Now it is stuck on the screen with the time and will not move forward, nor is it resets. Is there any solution for this?

    Thank you


    Try a forced reboot. Hold down the home and Sleep/Wake buttons simultaneously for about 15-20 seconds , until the Apple logo appears. You won't lose anything.

    If a force restart does not help try recovery Mode:


  • Satellite A100-225 keeps freezing and crashing with the new HARD drive

    Hi all

    I have a Satellite A100-225 with a 100 GB SATA Hitachi drive I int it that recently started showing bad sectors. Then I bought a Hitachi 320 GB SATA II drive to replace it. I tried the drive and it was recognized right away, so I didn't need to change the SATA speed. I ran the restore a disk installed newest. The problem I have is that the computer keeps freezing and crashing with the new drive. It takes a lot of time to load up when turned on and there is a noticeable to untermittant delay when you drag the cards around solo.

    I tried to run the Hitachi drive test and it comes back fine. I also tried to turn the SATA speed of the drive down from 300 to 150 via the firmware, and although I saw a slight improvement, it is still not right.

    I talked to Hitachi and they say that he could not be 100% compatible, so the problems. Someone at - it else sucessfully set up a replacement for this notebook drive and if so what make and model. Has anyone else had simular problems?

    Thank you

    Years ago, I've updated yet more former Satellite M70 with SATA HDD (270 GB if I m remembering well) and everything was fine.
    In my view upgrade with SATA HDD normal shouldn't be a problem. Do not SATA II because it will not work faster.

    I can't say for sure, but there must be a compatibility problem.

    Let's see if someone else had better luck with the upgrade of the disk on the Satellite A100.

    Have you checked this forum with advanced search option? Maybe you can find some old NET on upgrade the HDD on A100.

  • The new Firmware...

    Well... I downloaded the new firmware three times and it still doesn't work. What is happening is: I click on the icon (I put it on my desk), he asked me "do you want to run this file? I click on "Run" and the box that opens goes and nothing happens after that. He worked on the first download with my mp3 player. I have a Sansa clip and I had no problems with it until this week. What happened was: I turned it on and it works normally, it seemed, I chose my song, I wanted to listen to and carried on with what I was doing and then it off suddenly. I know that the battery was not dead because I had loaded this day here so I walk back and the Database "Refresh" came so I just went back for the song I was listening to - AND THE IT TURNS OFF AGAIN. So I try to turn it on, it going off, turn it on, it turns off. Finally, it no longer lights. Can I go online to do some troubleshooting to see what the problem was and I've saw that Firmware was supposed to help-so I did a security scan to make sure it was safe for my computer and started to download. As I said, the first time, I downloaded the software that it worked very well. But he said that I had to clear 6 MB of free space on my camera - I did everything what I deleted still shows up on my device so that I could not download the firmware, then I just gave up with it because I've had enough with it does not properly. Sansa never gave no problems so far. Is this the end for my mp3 player? I need to know if I can invest in something else.    Thank you.

    The original video had problems with bad Soldered joints on the battery terminal wires. Sorry to say, this is what it looks like happened to yours. If you are adventurous and handy with a soldering tip fine iron (or know someone who is) you can probably fix it.

    You can Google "dismantling the Sansa Clip" and find all kinds of Youtube videos and other pictograms on the way to get it out without damaging it and put it back together. Otherwise, I fear that it is ruined; transfer the files out of it (as long as it always connects to the computer) and get a new player, maybe a Clip + or Zip if you like the small size and as a bonus, these new players have a SC slot to expand memory.

  • How to change the SSID name of the computer to be Compatible with the new name SSID router

    Need to change the default name of the SSID router and then reconfigure adapters wireless in each PC to be compatible with the new router SSID.  A PC has Windows XP Home Edition Version 2002 Service Pack 3 and the other Vista Home Premium.  What are the steps to change the SSID on each PC?  Your response will help complete a home network wireless system.  Thanks in advance.


    Your computers use the SSID of your router - sound essentially its name.

    Check this box:
    Setting up a wireless router with Vista

    If necessary:

    Make sure you know the details of connection to your wireless router - SSID and password.

    You lose connection when you do and have to redo your logon.

    Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
    lower left click on merge or delete network locations - REMOVE all instances of your network (and the
    others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

    Setting up a wireless router with Vista

    I hope this helps.

    Rob - bicycle - Mark Twain said it is good.

  • I have updated to the new firmware, cannot connect to WVC54GC


    I update my WVC54GC (V1.1) with the latest firmware from the site (ver 1.26), when the update is complete, blue Led restart, I stoked market once again, but I can't connect to the camera, I have reset, same problem, the led flashes blue awhile then drove on continious, I try to connect with the software (search for camera) and with the browser to the default IP address :, nothing...

    Maybe something wrong during the download of the firmware.

    How can I go back to the old firmware? is that their another method for hard reset it (other then on the reset button on the side)

    Thank you to for your advice.

    I solve this problem (after reset the cam for 30 seconds), all settings became as default, including the IP address are set to:

    I connect to my PC directly via the cable to the cam, so I changed the configuration of the network card in my PC to:



    Gateway: (this is the IP of the Cam)

    By this solution, I was connected directly to the cam, and I've reconfigured the settings; WiFi, new Ip,... then when I restarded the Cam; all future returned and the cam worked as before (I have not find otherwise with the latest firmware date V1.26 Feb 2008, I had before V1.21 date 2006).

    The funniest thing I bought the cable connection (reverse connection) Ethernet, and when I finished the configuration of the cam, I tried the standard cable (straight): this work is too, so you can use the standard Cam ethernet cable.

  • never had a disc of windows vista with the new laptop and no option to make a recovery disk, and I need to format my laptop to factory / clean, help!

    never had a disc of windows vista with the new laptop and no option to make a recovery disk, and I need to format my laptop to factory / clean, help!

    How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

    There is no Vista free download legal available.

    Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

    Normally, they do this for a cost of $ small.


    In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

    See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

    Normally, you have to press F10 or F11 at startup to start the recovery process...

    Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.


    Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

    They will tell you how to do this.

    Every computer manufacturer has their way of doing recovery disk/s.


    Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
    A good Vista DVD contains all versions of Vista.
    The product key determines which version of Vista is installed.

    There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

    If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu


    MS advice on the conduct of clean install.


    A tutorial on the use of a clean install


    Super Guide Windows Vista Installation

    After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

    Save all data, because it will be lost during a clean installation.

    See you soon.

    Mick Murphy - Microsoft partner

  • My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

    My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

    Hello brooksm549,
    Thank you for using communities of Apple Support.

    I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

    On the use of the battery on your iPhone, iPad and iPod touch

    When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

    Maximize the life of the battery and battery life

    Best regards.

Maybe you are looking for

  • Tecra M3: Question about the length of battery life

    I used to have a M2 which had a battery life of approximately 3 hours and 45 minutes. Last January, I had a M3 and was surprised it was only 1:30 running just Word and a memory low music program. Closing of the screen and running the program of music

  • Satellite A300D keyboard problem after using an external USB keyboard

    I use a Satellite A300D series laptop and while at home, I use a UBS keyboard on it, but once the laptop is used without a USB keyboard only some of the keys seem to work, I get number 6 when I press the i key. I thought that this could be because th

  • I have I can tell if my anti virus program is activated?

    I have installed mcafee but I don't know that it is enabled and working.

  • Is there a way to fill the new cartridges?

    I inserted 564 new cartridges in my printer and shortly after it stop working. My new printer accepts the same 564 cartridges, but I had to use the ink cartridges that came with the new printer because they were the cartridges 'setup '. Is there an e

  • If sqlplus session statement

    Hi allI have to get the result of a statement and continue.This runs a sqlplus session.Oracle 11gdeclare v_dname varchar (20);StartSelect djob.get_dbname in the sys.dual v_dname;end;If (v_dname = "PRD") thenrun IMMEDIATELY 'truncate table MY_DAT_TBL;